Characterization of an alkali‐treated grass fiber by thermogravimetric and X‐ray crystallographic analysis

The thermal behavior of grass fiber was characterized by means of thermogravimetric analysis and differential scanning calorimetry analysis. The results proved that the removal of water‐soluble matter improved the thermal behavior of grass fiber over that of unleached fiber, and this was further enhanced by an alkali treatment of the grass fiber. The isothermal weight loss of the grass‐fiber specimens was analyzed at 100, 200, and 300°C for different time periods. Accelerated aging of the grass‐fiber samples was carried out to determine the effect of aging on the tensile strength. Partially delignified grass fiber showed maximum thermal stability. X‐ray diffraction analysis was also performed to verify the composition and to correlate the change in the tensile strength due to the water leaching and alkali treatment. The processing of grass fiber with NaOH and NaClO₂ reduced the amorphous fraction in the fiber sample. This may have been a result of the loss of the amorphous noncellulosic components of the fibers and the degradation of the unordered regions of the grass fiber. However, mercerization of the grass fiber revealed an increase in the amorphous fraction after a certain time exposure, confirming the decrease in the crystallinity. The morphology of the water‐leached and alkali‐treated grass fiber was studied with scanning electron microscopy © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Curing characteristics and mechanical properties of alkali‐treated grass‐fiber‐filled natural rubber composites and effects of bonding agent

To improve adhesion between fiber and matrix, natural rubber was reinforced with a special type of alkali‐treated grass fiber (Cyperus Tegetum Rox b). The cure characteristics and mechanical properties of grass‐fiber‐filled natural rubber composites with different mesh sizes were studied with various fiber loadings. Increasing the amount of fibers resulted in the composites having reduced tensile strength but increased modulus. The better mechanical properties of the 400‐mesh grass‐fiber‐filled natural rubber composite showed that the rubber/fiber interface was improved by the addition of resorcinol formaldehyde latex (RFL) as bonding agent for this particular formulation. The optimum cure time decreased with increases in fiber loading, but there was no appreciable change in scorch time. Although the optimum cure time of vulcanizates having RFL‐treated fibers was higher than that of the other vulcanizates, it decreased with fiber loading in the presence of RFL as the bonding agent. But this value was lower than that of the rubber composite without RFL. Investigation of equilibrium swelling in a hydrocarbon solvent was also carried out. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3151–3160, 2006     

Flax fiber surface modifications: Effects on fiber physico mechanical and flax/polypropylene interface properties

This study arises on the opportunities of using flax fibers as reinforcement for polypropylene (PP) matrix composites. For this purpose, untreated flax fiber bundles obtained by a retting process have been used. For improving compatibility between flax fiber bundles and PP matrix, fiber surface treatments such as maleic anhydride, maleic anhydride polypropylene copolymer, and vinyltrimethoxy silane have been carried out. On the other hand, alkali treatment has also been carried out for fiber modification. The effect of surface modification on tensile properties of single fibers and also on fiber‐matrix interfacial shear strength (IFSS) has been analyzed. Finally, both optical microscopy and atomic force microscopy have been used for characterizing flax fiber microstructural features. The current study completes previous results to elucidate the influence of treatments on fiber surface and flax fiber‐PP interface. POLYM. COMPOS. 26:324–332, 2005. © 2005 Society of Plastics Engineers.     

Thermal exposure effects on the long‐term behavior of a mullite fiber at high temperature

The behavior of an oxide fiber at elevated temperatures was analyzed before and after thermal exposures. The material studied was a mullite fiber developed for high‐temperature applications, CeraFib 75. Heat treatments were performed at temperatures ranging from 1200°C to 1400°C for 25 hours. Quantitative high‐temperature X‐ray analysis and creep tests at 1200°C were carried out to analyze the effect of previous heat treatment on the thermal stability of the fibers. The as‐received fibers presented a metastable microstructure of mullite grains with traces of alumina. Starting at 1200°C, grain growth and phase transformations occurred, including the initial formation of mullite, followed by the dissociation of the previous alumina‐rich mullite phase. The observed transformations are continuous and occur until the mullite phase reaches a state near the stoichiometric 3/2 mullite. Only the fibers previously heat treated at 1400°C did not show further changes when exposed again to 1200°C. Overall, the heat treatments increased the fiber stability and creep resistance but reduced the tensile strength. Changes observed in the creep strain vs. time curves of the fibers were related to the observed microstructural transformations. Based on these results, the chemical composition of the stable mullite fiber is suggested.     

Banana fiber reinforced low-density polyethylene composites: effect of chemical treatment and compatibilizer addition

In this study, an attempt has been made to utilize banana fiber (a natural fiber from agricultural waste) as reinforcement for low-density polyethylene (LDPE) to develop environmental friendly composite materials. LDPE/banana fiber composites were fabricated at different fiber loadings (10, 15, 20, 25, and 30 wt %) using compression molding technique. The composite with the composition of 25 wt % banana fiber was observed to be optimum on the basis of biodegradability and mechanical properties. Further, the effect of banana fiber surface treatment (alkali and acrylic acid) on the mechanical properties, morphology and water absorption behavior of the LDPE/banana fiber composites in the absence and presence of compatibilizer (maleic anhydride grafted LDPE, MA-g-LDPE) was comparatively studied. The alkali and acrylic acid treatment of the banana fibers led to enhanced mechanical properties and water resistance property of the composites, and these properties got further improved by the addition of the compatibilizer. The addition of compatibilizer to the acrylic acid treated banana fiber composites showed the most effective improvement in the flexural and impact strength and also, exhibited a reduction in the water absorption capacity. However, the tensile strength of the compatibilized composites with treated fibers resulted in slightly lower values than those with untreated fibers, because of the degradation of fibers by chemical attack as was evidenced by scanning electron microscopy (SEM) micrographs. SEM studies carried out on the tensile fractured surface of the specimens showed improved fiber-matrix interaction on the addition of compatibilizer.     

Interfacial studies on the surface modified aramid fiber reinforced epoxy composites

In this work, solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. The effect of chemical treatment on aramid fiber has been studied in a composite system. The surface characteristics of aramid fibers were characterized by Fourier transform infrared spectroscopy (FTIR). The interfacial properties of aramid/epoxy composites were investigated by means of the single fiber pull‐out tests. The mechanical properties of the aramid/epoxy composites were studied by interlaminar shear strength (ILSS). As a result, it was found that RES surface treatment is superior to ECP grafting treatment in promoting the interfacial adhesion between aramid fiber and epoxy matrix, resulting in the improved mechanical properties of the composites. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. This was probably due to the presence of reactive functional groups on the aramid fiber surface, leading to an increment of interfacial binding force between fibers and matrix in a composite system. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:4165–4170, 2006     

Effects of alkalization on tensile,impact, and fatigue properties of hemp fiber composites

The effects of alkalization surface treatment on hemp fiber properties and the properties of hemp fiber–reinforced polyester composites have been studied. Hemp fibers were exposed to 1, 5, and 10% sodium hydroxide (NaOH) solutions. The tensile properties and interfacial shear strength of all alkalized fibers were found to lie within the range of nonalkalized fibers. Laminates were made of alkalized fibers with unsaturated polyester resin, using hand lay‐up and compression moulding. Alkalization of fibers at low concentrations of 1 and 5% resulted in improvements in tensile and fatigue properties of composites made from these fibers, but no such improvements were observed for 10% alkalized fiber composites. The improvements were attributed to improvement in fiber/matrix bonding after this treatment, which was also confirmed by scanning electron microscopy images. No improvement in impact damage tolerance was observed for any of these three alkalized fiber composites. Immersion in distilled water reduced water absorption compared with nonalkalized fiber composites; however, the tensile properties in water were similar to those for nonalkalized fiber composites. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Influence of fiber surface treatment on properties of Indian grass fiber reinforced soy protein based biocomposites

The influence of fiber treatment on the properties of biocomposites derived from grass fiber and soy based bioplastic was investigated with environmental scanning electron microscopy, thermal and mechanical properties measurements. Grass fibers were treated with alkali solution that reduced the inter-fibrillar region of the fiber by removing hemicellulose and lignin, which reduce the cementing force between fibrils. This led to a more homogenous dispersion of the biofiber in the matrix as well as increase in the aspect ratio of the fiber in the composite, resulting in an improvement in fiber reinforcement efficiency. This led to enhancement in mechanical properties including tensile and flexural properties as well as impact strength. Additionally, the alkali solution treatment increased the concentration of hydroxyl groups on the surface, which led to a better interaction between the fibers and the matrix.     

Producing high‐quality precursor polymer and fibers to achieve theoretical strength in carbon fibers: A review

The precursor fiber quality has a large impact on carbon fiber processing in terms of its performance, production yield, and cost. Polyacrylonitrile precursor fibers have been used commercially to produce strong carbon fibers with average tensile strength of 6.6 GPa. There is a scope to improve the average tensile strength of carbon fibers, since only 10% of their theoretical strength has been achieved thus far. Most attempts to increase the tensile strength of carbon fibers have been made during the conversion of precursor fiber to carbon fiber. This review highlights the potential opportunities to enhance the quality of the polyacrylonitrile‐based precursor fiber during polymer synthesis, spinning, and postspinning. These high‐quality precursor fibers can lead to new generation carbon fibers with improved tensile strength for high‐performance applications. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43963.     

Effects of chemical surface pretreatment on tensile properties of a single glass fiber and the glass fiber reinforced epoxy composite

The aim of this article is to determine the effect of surface pretreatments, prior to the silanization, on the structure and tensile properties of the glass fibers and their epoxy composites. Commercial glass fibers were washed with acetone to remove the soluble portion of sizing, calcinated for the removal of organic matter, activated for surface silanol regeneration, and silanizated with glycidoxypropyltrimethoxysilane (GPS). Tensile test was carried out. The morphology of pretreated glass fibers and the fracture surfaces of the epoxy composites were observed with a scanning electron microscope (SEM). The results revealed that both apparent modulus and strength of a single glass fiber and the glass fiber/epoxy resin composites strongly depend on the fiber surface pretreatments. The acetone treatment did not change appreciably the composition and tensile properties of glass fibers, but there was a weak interface between fibers and matrix. In calcinated and acid activated fibers, the two competitive effects was observed: (1) degradation of the fibers themselves and (2) improved interfacial adhesion between the glass fibers and the epoxy matrix, once the samples was silanizated. The ATR‐FTIR results show that the surface content of Si OH increases as reflected by the increasing of the Si O band, resulting in an interaction between silane coupling agent and glass fiber. POLYM. COMPOS., 91–100, 2016. © 2014 Society of Plastics Engineers     

Structure–property relationships in glass reinforced polyamide,part 2: The effects of average fiber diameter and diameter distribution

We present the results of an extensive study of the influence of average fiber diameter and the width of the diameter distribution on the performance of injection‐molded glass‐fiber reinforced polyamide 6,6. In the average fiber diameter range from 9 to 18 μm, dry‐as‐molded (DaM) composite unnotched impact and tensile strength decreased significantly. The composite notched impact performance and tensile modulus showed little dependence on fiber diameter. The influence of broadening the fiber diameter distribution by blending glass fiber samples of different average diameter was found to be particularly negative on the level of composite unnotched impact when compared at equal number average diameter. After hydrolysis treatment, the composite tensile strength and modulus exhibited a large drop compared to the DaM results. In contrast, the unnotched impact results became insensitive to fiber diameter after hydrolysis. The average level of unnotched impact after hydrolysis was sufficiently high to show an increase over DaM when the fiber diameter was above 14 μm. Residual fiber length correlated significantly with fiber diameter with a lower average length for thinner fibers. The interfacial shear strength was found to be in the range of 26–34 MPa for DaM composites. There was a highly significant inverse correlation between the DaM interfacial strength and the average fiber diameter. It is shown that results from both tensile and unnotched impact measurements can be brought back to single trend lines by using a Z average value for the average fiber diameter, which is more heavily weighted to the thicker fibers in the distribution. POLYM. COMPOS., 28:331–343, 2007. © 2007 Society of Plastics Engineers     

Understanding the relation between structural and mechanical properties of electrospun fiber mesh through uniaxial tensile testing

Polymeric electrospun fibers have the potential to be utilized for a variety of applications such as tissue engineering, filtration, and textiles, owing to their high surface area per unit mass. However, these applications have some form of dependency on the mechanical properties of fiber meshes. Therefore, the current study is aimed at understanding the mechanical behavior of electrospun fiber systems at different length scales in order to establish a correlation between their structure and mechanical properties. Micro‐/nano‐fiber meshes of polystyrene were fabricated by the process of electrospinning and were subjected to uniaxial tensile testing. High‐resolution imaging during tensile testing revealed the macroscopic and microscopic structural evolution of these fibers. Further, the dependence of tensile strength, % elongation, and toughness of fiber meshes on the orientation of the fibers were also experimentally observed. The continuum mechanics simulation studies of fiber meshes with different orientations corroborated well with these experimental studies. Comprehensively, these studies demonstrated the changes in mechanical behavior of electrospun fiber meshes owing to the reorientation and alignment of fibers in meshes at microscopic and macroscopic length scale during tensile testing. Such study can be extrapolate for the design and fabrication of load‐bearing tissues scaffolds, and filtration devices. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45012.     

An improved method for single fiber tensile test of natural fibers

An improved Single Fiber Tensile Test (SFTT) for the natural fibers was depicted. Natural fibers have irregular shape, and are not uniform along the fiber length and also from one fiber to another. Applying the conventional method, which determine the fiber cross‐section by measuring the fiber diameter using optical microscopy, will result in inaccurate properties of the natural fibers with large standard deviation (SD). In the proposed new SFTT method, an accurate cross‐section area could be obtained from the Scanning Electron Microscope observation of a flat and clear fractured end surface of carefully selected tensile‐tested fibers and calculated using imaging analysis. Applying this new approach, tensile strength of different types of flax fiber, including bast fiber, enzyme‐retted and water‐retted fiber provided SD of less than 11%, while those of these fibers determined by the conventional approach had SD of over 24%. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Studies of different kinds of fiber pretreating on the properties of PLA/sweet sorghum fiber composites

In this article, truly degradable composites were prepared using sweet sorghum fibers which are residue of ethanol fermentation industry as reinforcement and renewable resource‐based biodegradable polyester, poly(L ‐lactide) (PLLA) as matrix, they were fabricated by melt‐blending. The effect of different kinds of pretreatments (dilute sulfuric acid pretreatment, mild alkaline/oxidative pretreatment, steam explosion pretreatment) on mechanical properties of composites were investigated. Besides the composition of untreated and treated fibers as determined by Van soest method, Fourier transformed infrared (FTIR) spectroscopic and scanning electron microscopic (SEM) were also used to study the change of sweet sorghum fibers before and after pretreatments. Mechanical properties testing indicated that tensile strength and impact strength of PLLA/treated fibers were improved except the dilute sulfuric acid pretreated fibers reinforced PLA composite. The mild alkaline/oxidative pretreated fiber reinforced PLA composite showed highest tensile strength of 46.12 MPa and impact strength of 8.02 kJ/m² which was 15.5 and 33% higher than that of the control. The SEM of impact fracture surface and DMTA test were carried out to investigate the interfacial morphology and interfacial adhesion between the fiber and matrix. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Study of SiC fiber axial compressive behavior using tensile recoil measurement

SiC fibers have been widely investigated as reinforcements for advanced ceramic matrix composites owing to their excellent high-temperature properties. However, the axial compressive strength of SiC fibers has not been thoroughly studied. In this study, the compressive behavior of two SiC fiber types containing different compositions and thermal degradation were characterized by tensile recoil measurements. Results illustrated that the SiC fiber compressive strength was 30%–50% of its tensile strength, after heat treatment at 1200℃–1800℃ for 0.5 h in argon. The fiber compressive failure mechanism was studied, and a “shear-bending-cleavage” model was proposed for the recoil compression fracture of pristine SiC fibers. The average compressive and tensile strengths of the pristine SiC-II fiber were 1.37 and 3.08 GPa, respectively. After treatment at 1800℃ for 0.5 h in argon, the SiC-II fiber compressive strength decreased to 0.42 GPa, whereas the tensile strength reduced to 1.47 GPa. The mechanical properties of the fibers degraded after high-temperature treatment. This could be attributed to SiC grain coarsening and SiC_xO_y phase decomposition.     

Investigations of the preparation technology for polyglycolic acid fiber with perfect mechanical performance

Polyglycolic acid (PGA) fibers were prepared by melt‐spinning process in this report. The effects of spinning parameters, such as windup rates and drawn ratio, on the mechanical properties of the fibers were discussed by analyzing the internal stress of as‐spun fibers, axial sound velocity, fiber tenacity, etc. The results showed that windup rate had a slight effect on the macromolecular orientation degree of the as‐spun fibers, which was quite unusual for melt spinning, whereas, the subsequent drawing process effectively increased the macromolecular orientation degree of the PGA fibers and consequently increased the tensile strength of the fibers. Low internal stress of as‐spun fibers obtained at lower windup rate led to higher drawing ratio, and the drawn fibers possessed relatively excellent mechanical properties. As a contrast, higher windup rate resulted in the strong internal stress of the as‐spun fibers, which had a negative influence on the drawing process, and so the tensile strength of the drawn fibers was relatively poor. Therefore, PGA fiber with perfect mechanical performance could be prepared at the technical parameters of lower windup rate and higher drawing multiples as well as slow drawing rate. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Characteristics of banana fibers and banana fiber reinforced phenol formaldehyde composites‐macroscale to nanoscale

Microfibers and nanofibers were prepared from macro banana fibers by a steam explosion process. The fiber surface of chemically modified and unmodified banana fibers was investigated by atomic force microscopy, the studies revealed a reduction in fiber diameter during steam explosion followed by acid treatments. Zeta potential measurements were carried out to measure the acidic property of the fiber surface; the surface acidity was found to be increased from macrofibers to nanofibers. The thermal behavior of macrofibers, microfibers, and nanofibers were compared. Substantial increase in thermal stability was observed from macroscale to nanoscale, which proved the high thermal stability of nanofibers to processing conditions of biocomposite preparation. The composition of the fibers before and after steam explosion and acid hydrolysis were also analyzed using FT‐IR. It was found that the isolation of cellulose nanofibres occurs in the final step of the processing stage. Further macrocomposites, microcomposites, and nanocomposites were prepared and mechanical properties such as tensile, flexural and impact properties were measured and compared. The composites with small amount of nanofibers induces a significant increase in tensile strength (142%), flexural strength (280%), and impact strength (133%) of the phenol formaldehyde (PF) matrix, this increase is due to the interconnected web like structure of the nanofibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1239‐1246, 2013     

LaPO4 coating on alumina-based fiber: Strength retention of fiber and improvement of interfacial performances

The characteristics of the interface are the key factors that determine the mechanical properties and fracture behavior of fiber-reinforced ceramic matrix composites. Design and preparation of coatings which can preserve fiber strength and maintain appropriate interfacial bonding strength are of great challenges. LaPO₄ coating is a promising weak interface coating for oxide fiber reinforced oxide ceramic matrix composites. Through this coating, the toughening mechanism of the composite such as fiber pulling out and fiber debonding is triggered. The LaPO₄ coating was deposited on the surface of alumina-based fibers by a solution precursor heterogeneous precipitation method. The effects of different precursors and different deposition temperatures on fiber strength were studied, and the mechanism of the strength degradation of the coated fiber was analyzed. It was found that the fibers coated with phytic acid precursor and deposited at 90 °C had the highest tensile strength compared to other coated fibers. The retention of strength is attributed to its loosely stacked coating. Besides, a single fiber pullout test was carried out to evaluate the effect of the coating on the interface of the composites. The results show that the composites coated by depositing citric acid precursor and phytic acid precursor at 90 °C can reduce the interfacial bonding strength by 32.5% and 46.7%, respectively compared to uncoated composites. This study has potential application value in the preparation of ceramic matrix composites used in oxidation and high temperature environments.     

Mechanical properties of surface‐modified ultra‐high molecular weight polyethylene fiber reinforced natural rubber composites

The mechanical properties of ultra‐high molecular weight polyethylene (UHMWPE) fibers reinforced natural rubber (NR) composites were determined, and the effects of fiber surface treatment and fiber mass fraction on the mechanical properties of the composites were investigated. Chromic acid was used to modify the UHMWPE fibers, and the results showed that the surface roughness and the oxygen‐containing groups on the surface of the fibers could be effectively increased. The NR matrix composites were prepared with as‐received and chromic acid treated UHMWPE fibers added 0–6 wt%. The treated UHMWPE fibers increased the elongation at break, tear strength, and hardness of the NR composites, especially the tensile stress at a given elongation, but reduced the tensile strength. The elongation at break increased markedly with increasing fiber mass fraction, attained maximum values at 3.0 wt%, and then decreased. The tear strength and hardness exhibited continuous increase with increasing the fiber content. Several microfibrillations between the fiber and NR matrix were observed from SEM images of the fractured surfaces of the treated UHMWPE fibers/NR composites, which meant that the interfacial adhesion strength was improved. POLYM. COMPOS., 38:1215–1220, 2017. © 2015 Society of Plastics Engineers     

Water uptake,chemical characterization,and tensile behavior of modified banana–plantain fiber and their polyester composites

Banana–plantain fibers (BPFs) were treated with acetic anhydride (AA), epichlorohydrin (EP), and an acetic anhydride–epichlorohydrin blend (AA_EP). Natural fiber–polyester composites (PCs) were fabricated using untreated and treated BPF by the hand lay‐up technique. Modified BPF Raman and Infrared spectroscopy (ATR‐FTIR) analysis revealed losses of lignin and hemicelluloses and new chemical bonds that confirmed the replacement of part of the raw fiber hydroxyl groups, which gave rise to a degree of hydrophobicity in the treated fibers. This change altered their water sorption isotherms, swelling behavior in water, impedance spectroscopy, and XRD analysis. Assays of water absorption and tensile resistance for untreated BPF (U) and modified BPF polyester composites demonstrated a remarkable reduction in water intake, whereas tensile strength was maintained (P < 0.05) for the modified BPF polyester composites. POLYM. COMPOS., 37:2960–2973, 2016. © 2015 Society of Plastics Engineers