Influence of aminosilane‐functionalized carbon nanotubes on the rheometric,mechanical, electrical and thermal degradation properties of epoxidized natural rubber nanocomposites

We describe the preparation, characterization and physical properties of multiwalled carbon nanotube (MWCNT)‐filled epoxidized natural rubber (ENR) composites. To ensure better dispersion in the elastomer matrix, the MWCNTs were initially subjected to aminopropyltriethoxysilane (APS) treatment to bind amine functional groups (?NH₂) on the nanotube surface. Successful grafting of APS on the MWCNT surface through Si–O–C linkages was confirmed using Fourier transform infrared spectroscopy. Grafting of APS on the MWCNT surface was further corroborated using elemental analysis. ENR nanocomposites with various filler loadings were prepared by melt compounding to generate pristine and APS‐modified MWCNT‐filled elastomeric systems. Furthermore, we determined the effects of various filler loadings on the rheometric, mechanical, electrical and thermal degradation properties of the resultant composite materials. Rheometric cure characterization revealed that the torque difference increased with pristine MWCNT loading compared to the gum system, and this effect was more pronounced when silane‐functionalized MWCNTs were loaded, indicating that this effect was due to an increase in polymer–carbon nanotube interactions in the MWCNT‐loaded materials. Loading of silane‐functionalized MWCNTs in the ENR matrix resulted in a significant improvement in the mechanical, electrical and thermal degradation properties of the composite materials, when compared to gum or pristine MWCNT‐loaded materials.© 2013 Society of Chemical Industry     

Reduction of percolation threshold through double percolation in melt‐blended polycarbonate/acrylonitrile butadiene styrene/multiwall carbon nanotubes elastomer nanocomposites

We demonstrate a method that involves melt blending of polycarbonate (PC) and melt‐blended acrylonitrile butadiene styrene (ABS) with multiwall carbon nanotubes (MWCNTs) to prepare electrically conducting PC/MWCNT nanocomposites at significantly low MWCNT loading. The partial solubility of ABS in PC led to a selective dispersion of the MWCNTs in the ABS phase after melt‐blending PC and ABS. Thus, a sudden rise in electrical conductivity (∼10⁸ orders of magnitude) of the nanocomposites was found at 0.328 vol% of MWCNT, which was explained in terms of double percolation phenomena. By optimizing the ratio of PC and the ABS–MWCNT mixture, an electrical conductivity of 5.58 × 10⁻⁵ and 7.23 × 10⁻³ S cm⁻¹ was achieved in the nanocomposites with MWCNT loading as low as 0.458 and 1.188 vol%, respectively. Transmission electron microscopy revealed a good dispersion and distribution of the MWCNTs in the ABS phase, leading to the formation of continuous MWCNT network structure throughout the matrix even at very low MWCNT loading. Storage modulus and thermal stability of the PC were also increased by the presence of a small amount of MWCNTs in the nanocomposites.POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

Preparation and characterization of multi‐walled carbon nanotube/poly(ethylene terephthalate) nanoweb

Multi‐walled carbon nanotube (MWCNT)/Poly(ethylene terephthalate) (PET) nanowebs were obtained by electrospinning. For uniform dispersion of MWCNTs in PET solution, MWCNTs were functionalized by acid treatment. Introduction of carboxyl groups onto the surface of MWCNTs was examined by Fourier transform infrared (FTIR) spectroscopy and X‐ray diffraction (XRD) analysis. MWCNTs were added into 22 wt % PET solution in the ratio of 1, 2, 3 wt % to PET. The morphology of MWCNT/PET nanoweb was observed using field emission‐scanning electron microscopy (FE‐SEM) and transmission electron microscopy (TEM). The nanofiber diameter decreased with increasing MWCNT concentration. The distribution of the nanofiber diameters showed a bi‐modal shape when MWCNTs were added. Thermal and tensile properties of electrospun MWCNT/PET nanowebs were examined using a differential scanning calorimeter (DSC), thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA) and etc. Tensile strength, tensile modulus, thermal stability, and the degree of crystallinity increased with increasing MWCNT concentration. In contrast, elongation at break and cold crystallization temperature showed a contrary tendency. Electric conductivities of the MWCNT/PET nanowebs were in the electrostatic dissipation range. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Ethylene‐vinyl acetate copolymer/multiwalled carbon nanotube/organoclay nanocomposites

Ethylene‐vinyl acetate copolymer (EVA) was melt‐mixed with multiwalled carbon nanotubes (MWCNTs) and organoclays, and the effects of simultaneous use of organoclays and MWCNTs on the surface resistivity and tensile properties of EVA nanocomposites were investigated. The surface resistivity of EVA/MWCNT nanocomposite with 1 phr of MWCNT is out of our measurement range (above 10¹² Ω/square). With increasing content of organoclay from 0 to 3 phr, the surface resistivity of the EVA/MWCNT/organoclay nanocomposites with 1 phr MWCNT remains out of our measurement range. However, the surface resistivity of the nanocomposite decreases to 10⁶ Ω/square with addition of 5 phr organoclay. The tensile properties of EVA/MWCNT/organoclay nanocomposites with 1 phr MWCNT and 5 phr organocaly are similar to those of EVA/MWCNT nanocomposites with 5 phr MWCNT except tensile modulus. POLYM. COMPOS. 2012. © 2012 Society of Plastics Engineers     

A Solvent‐Free Dispersion Method for the Preparation of PET/MWCNT Composites

A simple, easily accessible solvent‐free method for the dispersion of MWCNTs into PET is proposed, based on the preparation of a microparticulate polymer/nanotube masterbatch via cryogenic impact‐milling and its subsequent melt blending with the bulk polymer. Thermal and mechanical properties of nanocomposites prepared using this method were evaluated as a function of nanotube concentration. Thermal stability was improved, and superior crystallization behavior of PET in the nanocomposites was observed. Significant improvements of around 25% in tensile strength and tensile modulus of the nanocomposites was achieved using this strategy, with only 0.25 wt.‐% MWCNT, compared to previous literature data where 1 wt.‐% MWCNT was employed.

     

Improved dielectric performance of polypropylene/multiwalled carbon nanotube nanocomposites by solid‐phase orientation

By means of a die‐drawing technique in the rubbery state, the effect of the orientation of the microstructure on the dielectric properties of polypropylene (PP)/multiwalled carbon nanotube (MWCNT) nanocomposites was examined in this study. The viscoelastic behavior of the PP/MWCNT nanocomposites with MWCNT weight loadings ranging from 0.25 to 5 wt % and the dielectric performance of the stretched PP/MWCNT nanocomposites at different drawing speeds and drawing ratios were studied to obtain insight into the influences of the dispersion and orientation state of the MWCNTs and matrix molecular chains. A viscosity decrease (ca. 30%) of the PP/MWCNT‐0.25 wt % (weight loading) melt was obviously due to the free volume effect. Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction were adopted to detect the orientation structure and the variation of crystal morphology of the PP/MWCNTs. Melting plateau regions, which indicated the mixed crystallization morphology for the stretched samples, were found in the DSC patterns instead of a single‐peak for the unstretched samples. We found that the uniaxial stretching process broke the conductive MWCNT networks and consequently increased the orientation of MWCNTs and molecular chains along the tensile force direction; this led to an improvement in the dielectric performance. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42893.     

Thermal conductivity and dynamic mechanical property of glycidyl methacrylate‐grafted multiwalled carbon nanotube/epoxy composites

The well dispersed multiwalled carbon nanotube (MWCNT)/epoxy composites were prepared by functionalization of the MWCNT surfaces with glycidyl methacrylate (GMA). The morphology and thermal properties of the epoxy nanocomposites were investigated and compared with the surface characteristics of MWCNTs. GMA‐grafted MWCNTs improved the dispersion and interfacial adhesion in epoxy resin, and enhanced the network structure. The storage modulus of 3 phr GMA‐MWCNTs/epoxy composites at 50°C increased from 0.32 GPa to 2.87 GPa (enhanced by 799%) and the increased tanδ from 50.5°C to 61.7°C (increased by 11.2°C) comparing with neat epoxy resin, respectively. Furthermore, the thermal conductivity of 3 phr GMA‐MWCNTs/epoxy composite is increased by 183%, from 0.2042 W/mK (neat epoxy) to 0.5781 W/mK. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical and thermal properties of polyphenylene sulfide/multiwalled carbon nanotube composites

Polyphenylene sulfide (PPS)/multiwalled carbon nanotube (MWCNT) composites were prepared using a melt‐blending procedure combining twin‐screw extrusion with centrifugal premixing. A homogeneous dispersion of MWCNTs throughout the matrix was revealed by scanning electron microscopy for the nanocomposites with MWCNT contents ranging from 0.5 to 8.0 wt %. The mechanical properties of PPS were markedly enhanced by the incorporation of MWCNTs. Halpin‐Tsai equations, modified with an efficiency factor, were used to model the elastic properties of the nanocomposites. The calculated modulus showed good agreement with the experimental data. The presence of the MWCNTs exhibited both promotion and retardation effects on the crystallization of PPS. The competition between these two effects results in an unusual change of the degree of crystallinity with increasing MWCNT content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

High‐performance electromagnetic interference shielding material based on an effective mixing protocol

A facile and economic method is developed for the fabrication of new lightweight materials with high electromagnetic interference (EMI) shielding performance, good mechanical properties and low electrical percolation threshold through melt mixing. Electrical properties, DC conductivity, EMI shielding performance and mechanical properties of poly(trimethylene terephthalate) (PTT)/multiwalled carbon nanotube (MWCNT) nanocomposites with varying filler loading of MWCNTs were investigated. High‐resolution transmission electron microscopy was used to determine the distribution of MWCNTs in the PTT matrix. The newly developed nanocomposites show excellent dielectric and EMI shielding properties. Theoretical electrical percolation threshold was achieved at 0.21 wt% loading of MWCNTs, due to the high aspect ratio and the three‐dimensional network formation of MWCNTs. Experimental DC conductivity values were compared with those of theoretical models such as the Voet, Bueche and Scarisbrick models, which showed good agreement. The PTT/3% MWCNT composite showed an EMI shielding value of ～38 dB (99.99% attenuation) with a sample thickness of 2 mm. Power balance was used to determine the actual contribution of reflection, absorption and transmission loss to the total EMI shielding value. The nanocomposites showed good tensile and impact properties and the composite with 2% MWCNTs exhibited an improvement in tensile strength of as much as 96%. © 2018 Society of Chemical Industry     

Electrical and mechanical properties of acrylonitrile‐butadiene‐styrene/multiwall carbon nanotube nanocomposites prepared by melt‐blending

The electrical properties in polymer/carbon nanotube (CNT) nanocomposites are governed not only by the degree of dispersion but also to a greater extent on the aspect ratio of the CNTs in the final composites. Melt‐mixing of polymer and CNTs at high shear rate usually breaks the CNTS that lowers the aspect ratio of the nanotubes. Thus, homogeneous dispersion of CNTs while retaining the aspect ratio is a major challenge in melt‐mixing. Here, we demonstrate a novel method that involves melt‐blending of acrylonitrile‐butadiene‐styrene (ABS) and in situ polymerized polystyrene (PS)/multiwalled CNT (MWCNT) nanocomposites, to prepare electrically conducting ABS/MWCNT nanocomposites with very low CNT loading than reported. The rationale behind choosing PS/MWCNT as blending component was that ABS is reported to form miscible blend with the PS. Thus, (80/20 w/w) ABS/(PS/MWCNT) nanocomposites obtained by melt‐blending showed electrical conductivity value ≈1.27 × 10^?6 S cm^?1 at MWCNT loading close to 0.64 wt %, which is quite lower than previously reported value for ABS/MWCNT system prepared via solution blending. Scanning electron microscopy and differential scanning calorimetry analysis indicated the formation of homogenous and miscible blend of ABS and PS. The high temperature (100°C) storage modulus of ABS (1298 MPa) in the nanocomposites was increased to 1696 MPa in presence of 0.64 wt % of the MWCNT. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis of glass fiber‐multiwall carbon nanotube hybrid structures for high‐performance conductive composites

The conductive polyamide 66 (PA66)/carbon nanotube (CNT) composites reinforced with glass fiber‐multiwall CNT (GF‐MWCNT) hybrids were prepared by melt mixing. Electrostactic adsorption was utilized for the deposition of MWCNTs on the surfaces of glass fibers (GFs) to construct hybrid reinforcement with high‐electrical conductivity. The fabricated PA66/CNT composites reinforced with GF‐MWCNT hybrids showed enhanced electrical conductivity and mechanical properties as compared to those of PA66/CNT or PA66/GF/CNT composites. A significant reduction in percolation threshold was found for PA66/GF‐MWCNT/CNT composite (only 0.70 vol%). The morphological investigation demonstrated that MWCNT coating on the surfaces of the GFs improved load transfer between the GFs and the matrix. The presence of MWCNTs in the matrix‐rich interfacial regions enhanced the tensile modulus of the composite by about 10% than that of PA66/GF/CNT composite at the same CNT loading, which shows a promising route to build up high‐performance conductive composites. POLYM. COMPOS. 34:1313–1320, 2013. © 2013 Society of Plastics Engineers     

Properties of surface‐modified multiwalled carbon nanotube filled poly(ethylene terephthalate) composite films

Poly(ethylene terephthalate) (PET)/multiwalled carbon nanotube (MWCNT) composites were prepared by in situ polymerization. To improve the dispersion of MWCNTs in the PET matrix, functionalized MWCNTs having acid groups (acid‐MWCNTs) and acetic groups (acetic‐MWCNTs) on their surfaces were used. The functional groups were confirmed by infrared spectrometry. Scanning electron microscopy showed that acetic‐MWCNTs had a better dispersion in the PET matrix than pristine MWCNTs and acid‐MWCNTs. A reaction between PET and acetic‐MWCNTs was confirmed by a shift of the Raman G band to a higher frequency and an increase of the complex viscosity in the rheological properties. The composites containing functionalized MWCNTs showed a large increase in their tensile strengths and moduli. The values of the strengths and moduli of the PET/acetic‐MWCNT composites were higher than those of the PET/acid‐MWCNT composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Low percolation threshold and high electrical conductivity in melt‐blended polycarbonate/multiwall carbon nanotube nanocomposites in the presence of poly(ε‐caprolactone)

This study focuses on the electrical properties of polycarbonate (PC)/poly(ε‐caprolactone) (PCL)‐multiwall carbon nanotube (MWCNT) nanocomposites. MWCNTs were incorporated into thermoplastic PC matrix by simple melt blending using biodegradable PCL based concentrates with MWCNT loadings (3.5 wt%). Because of the lower interfacial energy between MWCNT and PCL, the nanotubes remain in their excellent dispersion state into matrix polymer. Thus, electrical percolation in PC/PCL‐MWCNT nanocomposites was obtained at lower MWCNT loading rather than direct incorporation of MWCNT into PC matrix. AC and DC electrical conductivity of miscible PC/PCL‐MWCNT nanocomposites were studied in a broad frequency range, 10¹?10⁶ Hz and resulted in low percolation threshold (p_c) of 0.14 wt%, and the critical exponent (t) of 2.09 from the scaling law equation. The plot of logσ_DC versus p^?1/3 showed linear variation and indicated the existence of tunneling conduction among MWCNTs. At low MWCNT loading, the influence of large polymeric gaps between conducting clusters is the reason for the frequency dependent electrical conductivity. Transmission electron microscopy and field emission scanning electron microscopy showed that MWCNTs were homogeneously dispersed and developed a continuous interconnected network path throughout the matrix phase and miscibility behavior of the polymer blend. POLYM. ENG. SCI., 54:646–659, 2014. © 2013 Society of Plastics Engineers     

Electrical and rheological percolation in poly(vinylidene fluoride)/multi‐walled carbon nanotube nanocomposites

Nanocomposites of poly(vinylidene fluoride) (PVDF) and multi‐walled carbon nanotubes (MWCNTs) were prepared through melt blending in a batch mixer (torque rheometer equipped with a mixing chamber). The morphology, rheological behavior and electrical conductivity were investigated through transmission electron microscopy, dynamic oscillatory rheometry and the two‐probe method. The nanocomposite with 0.5 wt% MWCNT content presented a uniform dispersion through the PVDF matrix, whereas that with 1 wt% started to present a percolated network. For the nanocomposites with 2 and 5 wt% MWCNTs the formation of this nanotube network was clearly evident. The electrical percolation threshold at room temperature found for this system was about 1.2 wt% MWCNTs. The rheological percolation threshold fitted from viscosity was about 1 wt%, while the threshold fitted from storage modulus was 0.9 wt%. Thus fewer nanotubes are needed to approach the rheological percolation threshold than the electrical percolation threshold. Copyright © 2010 Society of Chemical Industry     

in situ synthesis of biopolyurethane nanocomposites reinforced with modified multiwalled carbon nanotubes

Biopolyurethane nanocomposites reinforced with silane‐modified multiwalled carbon nanotubes (s‐MWCNT) were successfully prepared. The carbon nanotube surfaces were modified by means of functional amine groups via ozone oxidation followed by silanization. The surface structure of the s‐MWCNTs was characterized by Fourier transform infrared spectroscopy, X‐ray photoelectron spectroscopy, and thermogravimetric analysis. The s‐MWCNTs were incorporated into a vegetable oil‐based polyurethane (PU) network via covalent bonding to prepare PU nanocomposites. The effect of s‐MWCNT loading on the morphology, thermomechanical, and tensile properties of the PU nanocomposites was studied. It was determined that the s‐MWCNTs were dispersed effectively in the polymer matrix and that they improved the interfacial strength between the reinforcing nanotubes and the polymer matrix. Storage modulus, glass transition temperature, Young's modulus, and tensile strength of the nanocomposites increased with increasing s‐MWCNT loading up to 0.8%. However, increasing the s‐MWCNT content to 1.2 wt % resulted in a decrease in thermomechanical properties of the PU nanocomposites. This effect was attributed to the fact that at high s‐MWCNT contents, the increased number of amine groups competed with the polyol's hydroxyl groups for isocyanate groups, causing a decrease in the integrity of the PU matrix. High s‐MWCNT contents also facilitated aggregation of the nanotubes, causing a decrease in thermomechanical properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42515.     

Unique nucleation of multi-walled carbon nanotube and poly(ethylene 2,6-naphthalate) nanocomposites during non-isothermal crystallization

Multi-walled carbon nanotube (MWCNT) and poly(ethylene 2,6-naphthalate) (PEN) nanocomposites are prepared by a melt blending process. There are significant dependence of non-isothermal crystallization behavior and kinetics of PEN/MWCNT nanocomposites on the MWCNT content and cooling rate. The incorporation of MWCNT accelerates the mechanism of nucleation and crystal growth of PEN, and this effect is more pronounced at lower MWCNT content. Combined Avrami and Ozawa analysis is found to be effective in describing the non-isothermal crystallization of the PEN/MWCNT nanocomposites. The MWCNT in the PEN/MWCNT nanocomposites exhibits much higher nucleation activity than any nano-scaled reinforcement. When a vary small quantity of MWCNT was added, the activation energy for crystallization is lower, then gradually increased, and becomes higher than that of pure PEN above 1.0 wt% MWCNT content. The incorporation of MWCNT improves the storage modulus and loss modulus of PEN/MWCNT nanocomposites.     

Thermal‐Insulation,Electrical, and Mechanical Properties of Highly‐Expanded PMMA/MWCNT Nanocomposite Foams Fabricated by Supercritical CO2 Foaming

Foaming behavior of poly(methyl methacrylate) (PMMA)/multi‐walled carbon nanotubes (MWCNTs) nanocomposites and thermally‐insulating, electrical, and mechanical properties of the nanocomposite foams are investigated. PMMA/MWCNT nanocomposites containing various amounts of MWCNTs are first prepared by combining solution and melt blending methods, and then foamed using CO₂. The foaming temperature and MWCNT content are varied for regulating the structure of PMMA/MWCNT nanocomposite foams. The electrical conductivity measurement results show that MWCNTs have little effect on the electrical conductivity of foams with large expansion ratio. Thermal conductivities of both solid and foamed PMMA/MWCNT nanocomposites are measured to evaluate their thermally insulating properties. The gas conduction, solid conduction, and thermal radiation of the foams are calculated for clarifying the effects of cellular structure and MWCNT content on thermal insulation properties. The result demonstrates that MWCNTs endowed foams with enhanced thermal insulation performance by blocking thermal radiation. Moreover, the compressive testing shows that MWCNTs improve the compressive strength and rigidity of foams. This research is essential for optimizing environmentally friendly thermal insulation nanocomposite foams with enhanced thermal‐insulation and compressive mechanical properties.     

The enhanced mechanical properties of a covalently bound chitosan‐multiwalled carbon nanotube nanocomposite

In the present work, chitosan (CS)‐grafted multiwalled carbon nanotube (MWCNT) nanocomposites were prepared via covalently bonded CS onto MWCNTs that had weight fractions of MWCNTs ranging from 0.1 to 3.0 wt % by a simple method of solution casting. The structure, morphology, and mechanical properties of the films were investigated by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, optical microscopy, wide‐angle X‐ray diffraction, contact angle, and tensile testing. The results indicated that the CS chains were attached onto the MWCNTs successfully via covalent linkages. More interestingly, the MWCNTs provided a matrix that facilitated the crystallization of CS. Compared with the pure CS, the tensile strength and Young's modulus of the nanocomposites were enhanced significantly from 39.6 to 105.6 MPa and from 2.01 to 4.22 GPa with an increase in the MWCNT loading level from 0 to 3.0 wt %, respectively. The improvement in the tensile strength and modulus were ascribed to the uniform dispersion of MWCNTs covalently linked to the CS matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

The effect of multiwalled carbon nanotube dimensions on the morphology,mechanical, and electrical properties of melt mixed polypropylene‐based composites

The effect of multiwalled carbon nanotube (MWCNT) dimensions and surface modification on the morphology, mechanical reinforcement, and electrical properties of PP‐based composites, prepared by melt mixing, has been studied. The MWCNTs of small (d < 10 nm) and large (d = 40–60 nm) diameters with various intrinsic aspect ratios (L/d) have been used as filler. Transmission electron microscopy and very cold neutrons (VCN) scattering showed that both as‐received and surface modified small diameter MWCNT(1)s exhibit a strong tendency to bundle or cluster together in melt compared to both long MWCNT(3)s and short MWCNT(2)s large diameter nanotubes. The fractions of isolated nanotubes are higher and the mass‐fractal dimensions are lower for thick MWCNT‐based nanocomposites. The nanotubes of all types are heterogeneous nucleation sites for PP crystallization. The tensile and DMA testing results revealed that both long thick MWCNT(3)s with L/d ≈ 300 and thin MWCNT(1)s with highest intrinsic L/d > 1000 exhibit similar reinforcing effects, because drastically decreasing the effective aspect ratio (L/d)_eff of the thin flexibly nanotubes within polymer matrix. The nanocomposites based on the long large diameter MWCNT(3)s demonstrated the lowest percolation threshold equal to 1.5 vol % loading, highest dielectric and electromagnetic waves shielding properties. It was concluded that the choice of optimal diameter and length of MWCNTs is right approach to the improvement in the dispersion state and straightness of multiwelled carbon nanotubes in polymer melt as well as to enhancement of their efficiency as reinforcing and conductive nanosized filler. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Electrical conductivity and oxygen permeability of polyacrylonitrile/multiwalled carbon nanotubes composites

Polyacrylonitrile (PAN)/Multiwalled carbon nanotube (MWCNT) nanocomposites were prepared by nonconventional ultrasonic‐assisted emulsifier free emulsion polymerization technique with variable percentage of functionalized carbon nanotube. PAN/MWCNT nanocomposites were characterized by ultraviolet‐visible (UV‐visible) spectroscopy and Fourier transform infrared (FTIR) spectroscopy. The result from UV‐visible suggested that the functionalized MWCNT had interfacial interaction with PAN matrices. The surface morphology of functionalized MWCNT and PAN/MWCNT nanocomposites were studied by scanning electron microscopy (SEM). Electrical properties of PAN/MWCNT nanocomposites were measured and the result indicated that the conductivity increased with increasing concentration of MWCNTs. The oxygen permeability of PAN/MWCNT nanocomposites gradually increased with increase of MWCNT concentration, the result which was in agreement with the vertical alignment ofMWCNT in SEM. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers