Synthesis and characterization of high‐density polypropylene‐grafted polyethylene via a macromolecular reaction and its rheological behavior

High‐density polyethylene grafted isotactic polypropylene (PP‐g‐HDPE) was prepared by the imidization reaction between maleic anhydride grafted polyethylene and amine‐grafted polypropylene in a xylene solution. The branch density was adjusted by changes in the molar ratio between maleic anhydride and primary amine groups. Dynamic rheology tests were conducted to compare the rheological properties of linear polyolefins and long‐chain‐branched polyolefins. The effects of the density of long‐chain branches on the rheological properties were also investigated. It was found that long‐chain‐branched hybrid polyolefins had a higher storage modulus at a low frequency, a higher zero shear viscosity, a reduced phase angle, enhanced shear sensitivities, and a longer relaxation time. As the branch density was increased, the characteristics of the long‐chain‐branched structure became profounder. The flow activation energy of PP‐g‐HDPE was lower than that of neat maleic anhydride grafted polypropylene (PP‐g‐MAH) because of the lower flow activation energy of maleic anhydride grafted high‐density polyethylene (HDPE‐g‐MAH). However, the flow activation energy of PP‐g‐HDPE was higher than that of PP‐g‐MAH/HDPE‐g‐MAH blends because of the presence of long‐chain branches. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Peroxide‐catalyzed swell grafting of maleic anhydride onto polypropylene

A new grafting method was developed to incorporate maleic anhydride directly onto solid‐state polypropylene powders. Maleic anhydride grafts altered the nonpolar characteristics of polypropylene so that much better mixing was achieved in blends and composites of polypropylene with many other polymers and fillers. Maleic anhydride was grafted onto polypropylene by the peroxide‐catalyzed swell grafting method, with a maximum extent of grafting of 4.60%. Fourier transform infrared spectroscopy, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, tensile testing, and impact testing were used to characterize the isotactic polypropylene (iPP), maleic anhydride grafted polypropylene (MAH‐g‐iPP), and (isotactic polypropylene)/(calcium carbonate) composites (iPP/CaCO₃). The crystallinity and heat of fusion of the MAH‐g‐iPP decreased as the extent of grafting increased. The mechanical properties of the CaCO₃ filled polypropylene were improved by adding MAH‐g‐iPP as a compatibilizing agent. The dispersion of the fillers in the polymer matrix and the adhesion between the CaCO₃ particles and the polymer matrix were improved by adding the compatibilizer.     

Crystallization behavior of PP/PP‐g‐MAH/GFR PA66 blends: Establishment of their continuous‐cooling‐transformation of relative crystallinity diagrams

Polypropylene/polypropylene‐grafted‐maleic anhydride/glass fiber reinforced polyamide 66 (PP/PP‐g‐MAH/GFR PA 66) blends‐composites with and without the addition of polypropylene‐grafted‐maleic anhydride (PP‐g‐MAH) were prepared in a twin screw extruder. The effect of the compatibilizer on the thermal properties and crystallization behavior was determined using differential scanning calorimetry analysis. The hold time was set to be equal to 5 min at 290°C. These conditions are necessary to eliminate the thermomechanical history in the molten state. The crystallization under nonisothermal conditions and the plot of Continuous‐Cooling‐Transformation of relative crystallinity diagrams of both PP and PA 66 components proves that PP is significantly affected by the presence of PP‐g‐MAH. From the results it is found that an abrupt change is observed at 2.5 wt % of PP‐g‐MAH as a compatibilizer and then levels off. In these blends, concurrent crystallization behavior was not observed for GFR PA66. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1620–1626, 2007     

Effect of the compatibilizer on the morphology and properties of dynamically cured PP/POE/epoxy blends

Dynamic vulcanization was successfully applied to epoxy resin reinforced polypropylene (PP)/ethylene‐octene copolymer (POE) blends, and the effects of different compatibilizers on the morphology and properties of dynamically cured PP/POE/epoxy blends were studied. The results show that dynamically cured PP/POE/epoxy blends compatibilized with maleic anhydride‐grafted polypropylene (MAH‐g‐PP) have a three‐phase structure consisting of POE and epoxy particles dispersed in the PP continuous phase, and these blends had improved tensile strength and flexural modulus. While using maleic anhydride‐grafted POE (MAH‐g‐POE) as a compatibilizer, the structure of the core‐shell complex phase and the PP continuous phase showed that epoxy particles could be embedded in MAH‐g‐POE in the blends, and gave rise to an increase in impact strength, while retaining a certain strength and modulus. DSC analysis showed that the epoxy particles in the blends compatibilized with MAH‐g‐PP were more efficient nucleating agents for PP than they were in the blends compatibilized with MAH‐g‐POE. WAXD analysis shows that compatibilization do not disturb the crystalline structure of PP in the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Dynamically cured polypropylene/Novolac blends compatibilized with maleic anhydride‐g‐polypropylene

In this article, the dynamic vulcanization process was applied to polypropylene (PP)/Novolac blends compatibilized with maleic anhydride‐grafted PP (MAH‐g‐PP). The influences of dynamic cure, content of MAH‐g‐PP, Novolac, and curing agent on mechanical properties of the PP/Novolac blends were investigated. The results showed that the dynamically cured PP/MAH‐g‐PP/Novolac blend had the best mechanical properties among all PP/Novolac blends. The dynamic cure of Novolac improved the modulus and stiffness of the PP/Novolac blends. The addition of MAH‐g‐PP into dynamically cured PP/Novolac blend further enhanced the mechanical properties. With increasing Novolac content, tensile strength, flexural modulus, and flexural strength increased significantly, while the elongation at break dramatically deceased. Those blends with hexamethylenetetramine (HMTA) as a curing agent had good mechanical properties at HMTA content of 10 wt %. Scanning electron microscopy (SEM) analysis showed that dynamically cured PP/MAH‐g‐PP/Novolac blends had finer domains than the PP/MAH‐g‐PP/Novolac blends. Thermogravimetric analysis (TGA) results indicated that the incorporation of Novolac into PP could improve the thermal stability of PP. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Effect of compatibilizer on micromehanical deformations and morphology of dispersion in PP/PDMS blend

Role of maleic anhydride grafted polypropylene (PP‐g‐MAH) in interface modification in polypropylene (PP)/poly(dimethylsiloxane) (PDMS) elastomer blend has been investigated in this article through its effects on morphology of dispersion, micromechanical deformations such as voiding, crazing, shear yielding, fibrillation, and tensile behavior. During tensile deformation, PP/PDMS blend without the compatibilizer showed debonding at the elastomer‐matrix interface and it induced shear yielding and subsequently fibrillation in the matrix. The compatibilizer improved the interfacial adhesion between the PDMS domains and PP matrix, which prevented the debonding at elastomer‐matrix interface and the resulting shear yielding, and fibrillation was absent and rather caused extensive crazing in the matrix. Addition of PP‐g‐MAH reduced the size of dispersed PDMS domains, and narrowed the domain size distribution, which is attributed as an effect of interfacial adhesion produced by PP‐g‐MAH. Stress–strain curve and fibrillation also show similar effect of the interfacial adhesion caused by the compatibilizer. All these observations consistently lead to conclude that PP‐g‐MAH acts as a good compatibilizer for PP/PDMS blend. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Extrusion foaming behavior of a polypropylene/nanoclay microcellular foam

With maleic anhydride grafted polypropylene (PP‐g‐MAH) as a compatibilizer, composites of block‐copolymerized polypropylene (B‐PP)/nanoclay were prepared. The effects of the PP‐g‐MAH and nanoclay content on the crystallization and rheological properties of B‐PP were investigated. The microcellular foaming behavior of the B‐PP/nanoclay composite material was studied with a single‐screw extruder foaming system with supercritical (SC) carbon dioxide (CO₂) as the foaming agent. The experimental results show that the addition of nanoclay and PP‐g‐MAH decreased the melt strength and complex viscosity of B‐PP. When 3 wt % SC CO₂ was injected as the foaming agent for the extrusion foaming process, the introduction of nanoclay and PP‐g‐MAH significantly increased the expansion ratio of the obtained foamed samples as compared with that of the pure B‐PP matrix, lowered the die pressure, and increased the cell population density of the foamed samples to some extent. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44094.     

The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers     

Structure and properties of polypropylene/hydrotalcite nanocomposites

This article presents the study of the modification of the particle/matrix interface region and its effects on the structure and dynamic mechanical behavior of polypropylene (PP)/hydrotalcite nanocomposites prepared by melt extrusion. The interface modification was promoted by combinying the organophillization of the hydrotalcite particles with blending the PP with a maleic anhydride‐grafted‐PP (PP‐g‐MAH) or a maleic anhydride‐grafted‐poly(styrene‐co‐ethylenebutylene‐co‐styrene) (SEBS‐g‐MAH). Sodium dodecyl sulphate was used to promote the organophillization of the hydrotalcite particles. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) showed a partially exfoliated hydrotalcite structure, with an increasing exfoliation being achieved by adding a compatibilizer and organo‐modifying the particles. Values of the Young's modulus (E), storage modulus (E′), maximum tensile strength (σ_max), neck propagation strength (σ_neck), and elongation at break (ε_b) were found to depend both on the nature of the particle matrix interface as well as on the type of compatibilizer. Also, nanocomposites prepared with the organophillized particles showed lower T_g and loss factor values. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Crystallization kinetics of maleic anhydride‐modified iPP studied by POM

Melt nucleation and crystallization behavior of homo‐isotatic polypropylene (homo‐iPP), maleic anhydride (MAH)‐grafted‐iPP, and MAH‐modified iPP, produced from iPP and a small amount of MAH‐grafted‐iPP, was investigated by polarizing optical microscopy (POM), at T_c = 121–135^oC. Nucleation processes at a given T_c were faster for modified PP as compared to neat iPP. The induction time for nucleation increased nonlinearly with increasing T_c and decreased for modified PP, probably as a result of promoted heterogeneous nucleation due to the presence of carbonyl groups of MAH‐grafted‐PP. The average spherulite sizes were decreased by modification, and the growth rate was enhanced in maleated PP and modified PP. The induction time approach was applied to the results obtained by POM to compare the tendency for heterogeneous nucleation of neat and MAH‐modified PP. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3107–3118, 2000     

The effect of graft copolymers of maleic anhydride and epoxy resin on the mechanical properties and morphology of PP/ABS blends

In this work, maleic anhydride‐grafted polypropylene (PP‐g‐MAH) and maleic anhydride‐grafted poly(acrylonitrile‐butadiene‐styrene) (ABS‐g‐MAH) at 2 : 1 mass ratio were added as a compatibilizer in the PP/ABS blends. The compatibilizing effect was evaluated by adding the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ). The reaction in reactive extrusion, morphological structure, and properties of PP and ABS blends were investigated by using infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X‐ray spectrum, transmission electron microscope (TEM), dynamic thermomechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical properties tests. The results showed that the compatibilizing effect was greatly improved because of the addition of the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ) because the link structure of PP‐g‐MAH and ABS‐g‐MAH was formed by the reaction of anhydride group with epoxy group catalyzed by the imidazole. The size of the dispersed phase decreased dramatically, the interfacial adhesion between ABS particles and PP matrix was improved, and the tensile strength and flexural modulus of the PP/ABS blends increased further. The optimizing properties were obtained at 3 phr E51/2E4MZ. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40898.     

Effects of clay contents on the dynamic mechanical and rheological properties of polypropylene/MAH‐g‐POE/clay composites

A series of polypropylene/maleic anhydride grafted polypropylene octane elastomer (MAH‐g‐POE)/clay (PPMC) nanocomposites were prepared with a novel compatilizer MAH‐g‐POE and different contents of octadecyl amine modified montmorillonite, and the effects of clay contents on the dynamic mechanical and rheological properties of these PPMC composites were investigated. With clay content increasing, the characteristic X‐ray diffraction peak changed from one to two with intensity decreasing, indicating the decreasing concentration of the intercalated clay layers. The gradual decrease of crystallization temperature of PPMC composites with the increase of clay loading should be attributed to the preferred intercalation of MAH‐g‐POE molecules into clay interlayer during blending, which is also reflected by scanning electron microscopy observations. By evaluating the activation energy for the glass transition process of MAH‐g‐POE and polypropylene (PP) in the PPMC composites, it is found that clay intercalation could cause the restriction effect on the glass transition of both MAH‐g‐POE and PP, and this restriction effect appears stronger for PP and attained the highest degree at 5 wt % clay loading. The melt elasticity of PP could be improved apparently by the addition of MAH‐g‐POE, and 5 wt % clay loading is enough for further enhancing the elastic proportion of PP. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improvement of the physico‐mechanical properties and stability of waste polypropylene in the presence of wood flour and (maleic anhydride)‐grafted polypropylene

This paper deals with (maleic anhydride)‐grafted polypropylene (MAH‐g‐PP) and wood flour reinforcement and their effects on the dynamic, mechanical, morphological, and rheological properties of waste polypropylene (PP) composites. MAH‐g‐PP was used as a compatibilizer to improve the physical interaction between the filler and matrix. The composites were prepared by using a twin‐screw extruder followed by injection molding. Thermal stability and mechanical properties of the compatibilized system increased as compared to their values for the uncompatibilized system. Also, nearly 60% and 30% loss was found for mechanical properties and weight loss, respectively, in a biodegradability study. J. VINYL ADDIT. TECHNOL., 20:24–30, 2014. © 2014 Society of Plastics Engineers     

Isotactic polypropylene toughened with poly(acrylonitrile–butadiene–styrene): Compatibilizing role of maleic anhydride grafted polypropylene

The β‐nucleating activity and toughening effect of acrylonitrile–butadiene–styrene (ABS) graft copolymer on isotactic polypropylene (iPP) and the compatibilizing role of maleic anhydride grafted polypropylene (PP‐g‐MAH) on the iPP/ABS blends were investigated. The results show that ABS can induce the formation of β‐crystal in iPP, and its β‐nucleating efficiency depends on its concentration and dispersibility. The relative content of β‐crystal form is up to 36.19% with the addition of 2% ABS. The tensile and impact properties of the iPP were dramatically enhanced by introducing ABS. The incorporation of PP‐g‐MAH into the iPP/ABS blends inhibits the formation of β‐crystal. The crystallization peaks of the blends shift toward higher temperature, due to the heterogeneous nucleation effect of PP‐g‐MAH on iPP. The toughness of iPP/ABS blends improved due to favorable interfacial interaction resulting from the compatibilization of PP‐g‐MAH is significantly better than the β‐crystal toughening effect induced by ABS. POLYM. ENG. SCI., 59:E317–E326, 2019. © 2019 Society of Plastics Engineers     

Study on the microstructure and properties of bromobutyl rubber (BIIR)/polyamide‐12 (PA12) thermoplastic vulcanizates (TPVs)

In this study, polyamide‐12 (PA12)/brominated isobutylene‐isoprene (BIIR) TPVs with good mechanical properties and low gas permeability were prepared by dynamic vulcanization in a twin‐screw extruder. The effects of three kinds of compatibilizers on the microstructure and properties of BIIR/PA12 TPV were studied. The compatibility between BIIR and PA12 was improved when maleated hydrocarbon polymeric compatibilizer is added. The reaction between maleic anhydride and amine in polyamide leads to the in situ formation of hydrocarbon polymer grafted polyamide which subsequently can be used to lower the interfacial tension between BIIR and polyamide. The compatibilizing effect of maleic anhydride modified polypropylene (PP‐g‐MAH) on BIIR/PA12 blends is the best among these compatibilizers because the surface energy of PP‐g‐MAH is very close to that of BIIR. The dispersed rubber phase of the blend compatibilized by PP‐g‐MAH shows the smallest size and more uniform size distribution, and the resulting TPVs show the best mechanical properties. The effects of fillers on the properties of BIIR/PA12 TPV were also investigated. The size of the BIIR phase increases with the increase in the content of CaCO₃. The modulus and tensile strength of TPVs increased with the increase in the content of CaCO₃ because of the reinforcing effect of CaCO₃ on TPVs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43043.     

Structure and mechanism of functional isotactic polypropylene via in situ chlorination graft copolymerization

This paper discusses the structure and mechanism of maleic anhydride (MAH) grafted onto isotactic polypropylene (iPP) via in situ chlorination graft copolymerization (ISCGC). The molecular structure of the grafted iPP was characterized using ¹H NMR and ¹³C NMR spectroscopy, viscosity‐average molecular weight and gel content. The structure of un‐grafted MAH present in the reaction system was investigated using Fourier transform infrared spectroscopy in order to explore the grafting of MAH on iPP. The main side‐reactions, including iPP chain scission and crosslinking, during the grafting reaction were explored. From the experimental results obtained, the reason for controlled macromolecular chain degradation and crosslinking of grafted iPP in ISCGC is proposed. Based on the structural characterization of the grafted polymer, the mechanism of grafting onto iPP obtained via ISCGC was deduced. Mechanical properties, both static and dynamic, of grafted iPP were also investigated and the results showed that the properties of the material changed due to grafted MAH. Copyright © 2011 Society of Chemical Industry     

Dynamically cured polypropylene/epoxy blends

The dynamic vulcanization process, usually used for the preparation of thermoplastic elastomers, was used to prepare polypropylene (PP)/epoxy blends. The blends had crosslinked epoxy resin particles finely dispersed in the PP matrix, and they were called dynamically cured PP/epoxy blends. Maleic anhydride grafted polypropylene (MAH‐g‐PP) was used as a compatibilizer. The effects of the reactive compatibilization and dynamic cure were studied with rheometry, capillary rheometry, and scanning electron microscopy (SEM). The crystallization behavior and mechanical properties of PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends were also investigated. The increase in the torque at equilibrium for the PP/MAH‐g‐PP/epoxy blends indicated the reaction between maleic anhydride groups of MAH‐g‐PP and the epoxy resin. The torque at equilibrium of the dynamically cured PP/epoxy blends increased with increasing epoxy resin content. Capillary rheological measurements also showed that the addition of MAH‐g‐PP or an increasing epoxy resin content increased the viscosity of PP/epoxy blends. SEM micrographs indicated that the PP/epoxy blends compatibilized with PP/MAH‐g‐PP had finer domains and more obscure boundaries than the PP/epoxy blends. A shift of the crystallization peak to a higher temperature for all the PP/epoxy blends indicated that uncured and cured epoxy resin particles in the blends could act as effective nucleating agents. The spherulites of pure PP were larger than those of PP in the PP/epoxy, PP/MAH‐g‐PP/epoxy, and dynamically cured PP/epoxy blends, as measured by polarized optical microscopy. The dynamically cured PP/epoxy blends had better mechanical properties than the PP/epoxy and PP/MAH‐g‐PP/epoxy blends. With increasing epoxy resin content, the flexural modulus of all the blends increased significantly, and the impact strength and tensile strength increased slightly, whereas the elongation at break decreased dramatically. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1437–1448, 2004     

聚丙烯（PP）／黏土复合材料熔融剂的研究

以马来酸酐（MAH）等为单体接枝聚丙烯作为聚丙烯（PP）／黏土复合材料熔融剂,考察了马来酸酐用量、引发剂过氧化苯甲酰（BPO）用量、反应时间、温度等因素对产物接枝率的影响,并通过红外光谱图对PP-g-MAH进行表征。结果表明,当m（PP）：m（复配单体）：m（BPO）=10．0：2．0：0．6、反应温度控制在120℃左右、复配单体为马来酸酐／苯乙烯时,熔融剂PP-g-MAH的接枝率可获得较大值3．9％。实验同时表明,反应时间对接枝率的影响不大;苯乙烯的加入对接枝率有较大的影响,与普通单体单一马来酸酐相比,加入苯乙烯的接枝率明显提高。     

Blends of poly(ethylene terephthalate) bottle waste with modified styrene butadiene rubber through reactive mixing

Styrene butadiene rubber (SBR) was modified by the grafting reaction of maleic anhydride (MAH) in the presence of the initiator benzoyl peroxide (BPO). This modified elastomer was then blended with poly(ethylene terephthalate) (PET) bottle waste, and the mechanical and morphological properties of the resulting blends were studied. The amount of grafted MAH was determined by chemical titration. The results revealed that the concentrations of MAH and BPO strongly affected the grafting process. The morphology of the dispersed phase for blends of PET waste and SBR‐g‐MAH was quite different from that of a simple blend of PET waste and SBR. Dynamic mechanical thermal analysis revealed suitable compatibility between PET waste and styrene butadiene rubber‐graft‐maleic anhydride (SBR‐g‐MAH). The enhanced compatibility resulted in better impact properties. The better compatibility was concluded to result from bond formation between the carbonyl group of SBR‐g‐MAH and the hydroxyl or carboxyl end groups of PET. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1615–1623, 2006     

Preparation and characterization of high melt strength polypropylene with long chain branched structure by the reactive extrusion process

The reactive extrusion of maleic anhydride grafted polypropylene (PP‐g‐MAH) with ethylenediamine (EDA) as coupling agent is carried out in a corotating twin‐screw extruder to produce long chain branched polypropylene (LCBPP). Part of PP‐g‐MAH is replaced by maleic anhydride grafted high‐density polyethylene (HDPE‐g‐MAH) or linear low‐density polyethylene (LLDPE‐g‐MAH) to obtain hybrid long chain branched (LCB) polyolefins. Compared with the PP‐g‐MAH, PE‐g‐MAH, and their blends, the LCB polyolefins exhibit excellent dynamic shear and transient extensional rheological characteristics such as increased dynamic modulus, higher low‐frequency complex viscosity, broader relaxation spectra, significantly enhanced melt strength and strain‐hardening behaviors. The LCB polyolefins also have higher tensile strength, tensile modulus, impact strength and lower elongation at break than their blends. Furthermore, supercritical carbon dioxide (scCO₂) is constructively introduced in the reactive extrusion process. In the presence of scCO₂, the motor current of the twin extruder is decreased and LCB polyolefins with lower melt flow rate (MFR), higher complex viscosity and increased tensile strength and modulus can be obtained. This indicates that the application of scCO₂ can reduce the viscosity of melt in extruder, enhance the diffusion of reactive species, and then facilitate the long chain branching reaction between anhydride group and primary amine group. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011