Effect of organic modifiers and silicate type on filler dispersion,thermal, and mechanical properties of ABS‐clay nanocomposites

Acrylonitrile–butadiene–styrene (ABS)–clay composite and intercalated nanocomposites were prepared by melt processing, using Na‐montmorillonite (MMT), several chemically different organically modified MMT (OMMT) and Na‐laponite clays. The polymer–clay hybrids were characterized by WAXD, TEM, DSC, TGA, tensile, and impact tests. Intercalated nanocomposites are formed with organoclays, a composite is obtained with unmodified MMT, and the nanocomposite based on synthetic laponite is almost exfoliated. An unintercalated nanocomposite is formed by one of the organically modified clays, with similar overall stack dispersion as compared to the intercalated nanocomposites. T_g of ABS is unaffected by incorporation of the silicate filler in its matrix upto 4 wt % loading for different aspect ratios and organic modifications. A significant improvement in the onset of thermal decomposition (40–44°C at 4 wt % organoclay) is seen. The Young's modulus shows improvement, the elongation‐at‐break shows reduction, and the tensile strength shows improvement. Notched and unnotched impact strength of the intercalated MMT nanocomposites is lower as compared to that of ABS matrix. However, laponite and overexchanged organomontmorillonite clay lead to improvement in ductility. For the MMT clays, the Young's modulus (E) correlates with the intercalation change in organoclay interlayer separation (Δd₀₀₁) as influenced by the chemistry of the modifier. Although ABS‐laponite composites are exfoliated, the intercalated OMMT‐based nanocomposites show greater improvement in modulus. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Crystallization kinetics of poly (L‐lactic acid)/montmorillonite nanocomposites under isothermal crystallization condition

Poly(L ‐lactic acid)/o‐MMT nanocomposites, incorporating various amounts of organically modified montmorillonite (o‐MMT; 0–10 wt %), were prepared by solution intercalation. The montmorillonite (MMT) was organically modified with dilauryl dimethyl ammonium bromide (DDAB) by ion exchange. Transmission electron microscopy (TEM) and X‐ray diffraction (XRD) reveal that the o‐MMT was exfoliated in a poly(L ‐lactic acid), (PLLA) matrix. A series of the test specimens were prepared and subjected to isothermal crystallization at various temperatures (T₁–T₅). The DSC plots revealed that the PLLA/o‐MMT nanocomposites that were prepared under nonisothermal conditions exhibited an obvious crystallization peak and recrystallization, but neat PLLA exhibited neither. The PLLA/o‐MMT nanocomposites (2–10 wt %) yielded two endothermic peaks only under isothermal conditions at low temperature (T₁), and the intensity of Tm₂ (the higher melting point) was proportional to the o‐MMT content (at around 171°C). The melting point of the test samples increased with the isothermal crystallization temperature. In the Avrami equation, the constant of the crystallization rate (k) was inversely proportional to the isothermal crystallization temperature and increased with the o‐MMT content, especially at low temperature (T₁). The Avrami exponent (n) of the PLLA/o‐MMT nanocomposites (4–10 wt %) was 2.61–3.56 higher than that of neat PLLA, 2.10–2.56, revealing that crystallization occurred in three dimensions. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Liquid‐crystalline copolyester/clay nanocomposites

A series of novel polymer–clay nanocomposites, that is, liquid‐crystalline copolyester/montmorillonite (MMT) nanocomposites, were synthesized by the intercalation polycondensation of terephthalic acid, p‐acetoxy benzoic acid, and 1,2‐diacetoxy benzene in the presence of different organically modified montmorillonites (OMt's). The OMt's were prepared by the ion exchange of MMT with octadecylamine hydrochloride, p‐aminobenzoic acid hydrochloride, or lysine hydrochloride. X‐ray diffraction and transmission electron microscopy studies indicated that the inorganic cations in the MMT interlayers were already exchanged by organic onium ions and that the OMt intercalated with p‐aminobenzoic acid or lysine was good for obtaining more delaminated clay nanocomposites. The glass‐transition temperature and modulus of the nanocomposites increased compared with those of the pure polymer, whereas the isotropic temperature decreased. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3155–3159, 2003     

Synthesis and characterization of polyurethane cationomer/MMT hybrid composite

BACKGROUND: The development of polymeric nanocomposites incorporating intercalated or exfoliated layered silicate clays into the organic matrix has been substantially motivated by the significant improvements induced by the presence of the inorganic component. Moreover, understanding and controlling the dispersion of inorganic layers into segmented polyurethane matrices by means of ionic interactions, and exploiting these interactions to enhance physicomechanical behaviour, could be of great interest in the field of polymer nanocomposites. RESULTS: New cationic polyurethane elastomers were prepared starting from poly(butylene adipate)diol (M_n = 1000 g mol^?1), 4,4′‐diphenylmethane diisocyanate, 1,4‐butanediol and N‐methyldiethanolamine or N,N′‐β‐hydroxyethylpiperazine, used as potential quaternizable moieties. The characterization of the polymers was achieved using specific analyses employed for the macromolecular samples (Fourier transform infrared and ¹H NMR spectroscopy, thermogravimetric analysis (TGA), gel permeation chromatography). An extension of our research on polymers reinforced with organically modified montmorillonite (OM‐MMT) in order to prepare hybrid composites with improved properties was performed and the resulting materials were characterized using TGA, X‐ray diffraction, atomic force microscopy and scanning electron microscopy. Also, the mechanical properties of the cationic polyurethane/OM‐MMT composites were investigated in comparison with the pristine ionic/non‐ionic polymers and their composites containing non‐ionic polymer blended with OM‐MMT or ionic polymer and unmodified MMT. CONCLUSION: The insertion of the organically modified clay into the polymeric matrix gave an improvement of the mechanical properties of the polyurethane composites, especially the tensile strength and stiffness of the hybrid materials. Copyright © 2009 Society of Chemical Industry     

Synthesis of poly(butyl acrylate‐co‐methyl methacrylate)/montmorillonite waterborne nanocomposite via semibatch emulsion polymerization

Poly(butyl acrylate‐co‐methyl methacrylate)‐montmorillonite (MMT) waterborne nanocomposites were successfully synthesized by semibatch emulsion polymerization. The syntheses of the nanocomposites were performed in presence of sodium montmorillonite (Na‐MMT) and organically modified montmorillonite (O‐MMT). O‐MMT was used directly after the modification of Na‐MMT with dimethyl dioctadecyl ammonium chloride. Both Na‐MMT and O‐MMT were sonified to obtain nanocomposites with 47 wt % solids and 3 wt % Na‐MMT or O‐MMT content. Average particle sizes of Na‐MMT nanocomposites were measured as 110–150 nm while O‐MMT nanocomposites were measured as 200–350 nm. Both Na‐MMT and O‐MMT increased thermal, mechanical, and barrier properties (water vapor and oxygen permeability) of the pristine copolymer explicitly. X‐ray diffraction and transmission electron microscope studies show that exfoliated morphology was obtained. The gloss values of O‐MMT nanocomposites were found to be higher than that of the pristine copolymer. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42373.     

Structural characterization of hydrophilic polymer blends/montmorillonite clay nanocomposites

The nanocomposite films comprising polymer blends of poly(vinyl alcohol) (PVA), poly(vinyl pyrrolidone) (PVP), poly(ethylene oxide) (PEO), and poly(ethylene glycol) (PEG) with montmorillonite (MMT) clay as nanofiller were prepared by aqueous solution casting method. The X‐ray diffraction studies of the PVA–x wt % MMT, (PVA–PVP)–x wt % MMT, (PVA–PEO)–x wt % MMT and (PVA–PEG)–x wt % MMT nanocomposites containing MMT concentrations x = 1, 2, 3, 5 and 10 wt % of the polymer weight were carried out in the angular range (2θ) of 3.8–30°. The values of MMT basal spacing d₀₀₁, expansion of clay gallery width W_cg, d‐spacing of polymer spherulite, crystallite size L and diffraction peak intensity I were determined for these nanocomposites. The values of structural parameters reveal that the linear chain PEO and PEG in the PVA blend based nanocomposites promote the amount of MMT intercalated structures, and these structures are found relatively higher for the (PVA–PEO)–x wt % MMT nanocomposites. It is observed that the presence of bulky ester‐side group in PVP backbone restricts its intercalation, whereas the adsorption behavior of PVP on the MMT nanosheets mainly results the MMT exfoliated structures in the (PVA–PVP)–x wt % MMT nanocomposites. The crystallinities of the PEO and PEG were found low due to their blending with PVA, which further decreased anomalously with the increase of MMT concentration in the nanocomposites. The decrease of polymer crystalline phase of these materials confirmed their suitability in preparation of novel solid polymer nanocomposite electrolytes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40617.     

Influence of granulometry and organic treatment of a Brazilian montmorillonite on the properties of poly(styrene‐co‐n‐butyl acrylate)/layered silicate nanocomposites prepared by miniemulsion polymerization

The influence of granulometry and organic treatment of a Brazilian montmorillonite (MMT) clay on the synthesis and properties of poly(styrene‐co‐n‐butyl acrylate)/layered silicate nanocomposites was studied. Hybrid latexes of poly(styrene‐co‐butyl acrylate)/MMT were synthesized via miniemulsion polymerization using either sodium or organically modified MMT. Five clay granulometries ranging from clay particles smaller than 75 μm to colloidal size were selected. The size of the clay particles was evaluated by specific surface area measurements (BET). Cetyl trimethyl ammonium chloride was used as an organic modifier to enhance the clay compatibility with the monomer phase before polymerization and to improve the clay distribution and dispersion within the polymeric matrix after polymerization. The sodium and organically modified natural clays as well as the composites were characterized by X‐ray diffraction analysis. The latexes were characterized by dynamic light scattering. The mechanical, thermal, and rheological properties of the composites obtained were characterized by dynamical‐mechanical analysis, thermogravimetry, and small amplitude oscillatory shear tests, respectively. The results showed that smaller the size of the organically modified MMT, the higher the degree of exfoliation of nanoplatelets. Hybrid latexes in presence of Na‐MMT resulted in materials with intercalated structures. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

A comparative study on camphorsulphonic acid modified montmorillonite clay based conducting polymer nanocomposites

Nanotechnology has emerged as a subject of immense academic interest and excitement in the past few decades. The immediate goal of this science aims at the production of high performance nanomaterials. The present study reports comparative investigations on the in situ polymerization of polyaniline (PANI), and its derivatives poly(1‐naphthylamine) (PNA) and poly(o‐toluidine) (POT) within the camphor sulphonic acid (CSA) modified montmorillonite (MMT) layers. The polymerization as well as intercalation of the conducting polymers was confirmed by FT‐IR, UV‐visible spectroscopies, and XRD studies, whereas the morphology of the nanocomposites was analyzed by TEM studies. It was found that the PANI derivatives (PNA and POT) revealed higher intercalation as compared with PANI. The morphology of nanocomposites was found to be governed by the type of conducting polymer intercalated. A large variation in the morphology as well as particle size was observed between the nanocomposites of PANI and its derivatives. The conductivity was found to be in the range of 10⁻³–10⁻² S·cm⁻¹. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Preparation,properties, and anticorrosion application of poly(methyl methacrylate)/montmorillonite nanocomposites coating on brass via solution polymerization

The aim of this study is to improve the anticorrosive property of 7Cu3Zn brass. The methyl‐methacrylate (MMA) monomer solution, modified with fluorine radical and silicone, was used as the polymer matrix to mix with the different percentages of modified montmorillonite (MMT) loading and to exfoliate the lamellar structure of MMT on a nanometer scale during the solution polymerization process, and then form a thin nanocomposites coating on brass as a protective layer. The structural characterization was examined using Fourier transform infrared spectroscopy, X‐ray diffraction (XRD), and transmission electron microscope (TEM). The anticorrosive property of nanocomposites was evaluated using potentiodynamics polarization and electrochemical impedance spectra. The results show that the d‐spacing of MMT was increased, and both exfoliation and intercalation microstructure were observed. Moreover, with the MMT loading increase, the appearance of the intercalation microstructure was more remarkable as a result of silicate layers aggregation. The 1.0 wt %‐coated brass coupons presented the optimistic property of anticorrosion, whose oxygen permeability, corrosion current (i_corr), polarization resistance (R_p), and corrosion rate (R_corr) were 3.5 g/(m²°h), 6.86 nA/cm², 5.81 × 10⁵ Ω°cm², and 0.103 × 10^?3 mm/year, respectively. These results indicate that nanocomposites have potential for anticorrosion application. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4135–4143, 2007     

Effect of matrix molecular weight on the dispersion of nanoclay in unmodified high density polyethylene

The effect that polymer molecular weight has on the dispersion of relatively polar montmorillonite (MMT) in nonpolar, unmodified high density polyethylene (HDPE) was examined. Polymer layered silicate (PLS) nanocomposites were prepared via melt compounding in a single screw extruder using three unmodified HDPE matrices of differing molecular weight and organically modified MMT (organoclay) in concentrations ranging from 2 to 8 wt%. The weight average molecular weights (M _W) of the HDPE matrices used ranged from 87,000 to 460,000 g/mol. X‐ray diffraction (XRD), tensile testing, dynamic mechanical thermal analysis (DMTA), and dynamic rheometry were performed on these nanocomposites. Nanocomposites generated from the high molecular weight (HMW) HDPE matrix exhibited increased intercalation of the MMT as shown by XRD and greater improvements in the Young's modulus when compared with nanocomposites generated from the low (LMW) and middle molecular weight (MMW) matrices. DMTA measurements carried out in torsion showed that the increase in shear modulus of the HMW nanocomposites was not as great as that of the LMW and MMW counterparts as observed from a lower percentage enhancement in the storage modulus (G′) and estimated heat distortion temperature (HDT). This was attributed to the higher degree of mechanical anisotropy in the HMW nanocomposites. POLYM. COMPOS., 28:499–511, 2007. © 2007 Society of Plastics Engineers     

Influence of the type of quaternary ammonium salt used in the organic treatment of montmorillonite on the properties of poly(styrene‐co‐butyl acrylate)/layered silicate nanocomposites prepared by in situ miniemulsion polymerization

Hybrid latices of poly(styrene‐co‐butyl acrylate) were synthesized via in situ miniemulsion polymerization in the presence of 3 and 6 wt % organically modified montmorillonite (OMMT). Three different ammonium salts: cetyl trimethyl ammonium chloride (CTAC), alkyl dimethyl benzyl ammonium chloride (Dodigen), and distearyl dimethyl ammonium chloride (Praepagen), were investigated as organic modifiers. Increased affinity for organic liquids was observed after organic modification of the MMT. Stable hybrid latices were obtained even though miniemulsion stability was disturbed to some extent by the presence of the OMMTs during the synthesis. Highly intercalated and exfoliated polymer‐MMT nanocomposites films were produced with good MMT dispersion throughout the polymeric matrix. Materials containing MMT modified with the 16 carbons alkyl chain salt (CTAC) resulted in the largest increments of storage modulus, indicating that single chain quaternary salts provide higher increments on mechanical properties. Films presenting exfoliated structure resulted in the largest increments in the onset temperature of decomposition. For the range of OMMT loading studied, the nanocomposite structure influenced more significantly the thermal stability properties of the hybrid material than did the OMMT loading. The film containing 3 wt % MMT modified with the two 18 carbons alkyl chains salt (Praepagen) provided the highest increment of onset temperature of decomposition. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

The effect of clay modification on the mechanical properties of poly(methyl methacrylate)/organomodified montmorillonite nanocomposites prepared by in situ suspension polymerization

Poly(methylmethacrylate) (PMMA)/montmorillonite (MMT) nanocomposites were prepared by in situ suspension polymerization. MMT was previously organically modified by different modification agents [dioctadecyl dimethyl ammonium chloride (DODAC) and methacrylatoethyltrimethyl ammonium chloride (MTC)] and different modification method (cation‐exchange reaction and grafting reaction), ultimately giving rise to five kinds of organomodified MMT (OMMT). The structure of the OMMT was studied by Wide angle X‐ray diffraction (WAXD) and Fourier transform infrared spectroscopy (FTIR). Meanwhile, the structure of the PMMA/MMT nanocomposites microspheres was also investigated by WAXD. The molecular weight of the polymers extracted from PMMA/MMT nanocomposites was measured by gel permeation chromatograph (GPC). Finally, the mechanical properties of these PMMA/MMT nanocomposites were studied in detail. It was found that large interlayer spacing (d₀₀₁) of OMMT could not entirely ensure an exfoliated structure of resultant PMMA/MMT nanocomposites, while OMMT with relative small d₀₀₁ could still yield exfoliated structure as long as the compatibility between OMMT and polymer matrix was favorable. In addition, the results of mechanical investigation indicated that the compatibility between OMMT and PMMA matrix turned out to be the dominant factor deciding the final mechanical properties of PMMA/MMT nanocomposites. POLYM. COMPOS., 37:1705–1714, 2016. © 2014 Society of Plastics Engineers     

Mechanical properties and rheological behavior of poly(butylene terephthalate)/clay nanocomposites with different organoclays

Poly(butylene terephthalate)–clay nanocomposites with three different organically modified clays were prepared via melt blending in a twin‐screw extruder. Decyl triphenylphosphonium bromide, hexadecyl triphenylphosphonium bromide, and cetyl pyridinium chloride were used to modify the naturally occurring montmorillonite clay. The organically modified clays were characterized with X‐ray diffraction for the d₀₀₁‐spacing and with thermogravimetric analysis to determine the thermal stability. The prepared nanocomposites were injection‐molded and examined for the dispersion quality of the clay, the mechanical properties, and the rheological behavior. The tensile strength of the nanocomposites increased with a 1% addition of clay; however, more clay decreased the tensile strength. Nanocomposites with finely dispersed clay platelets and nanocomposites with poorly dispersed clay platelets showed very different rheological behaviors. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Crystallization behavior of nylon 11/montmorillonite nanocomposites under annealing

Exfoliated nylon 11/montmorillonite (MMT) nanocomposites were prepared via in situ polymerization by the dispersion of organically modified MMT in 11‐aminoundecanoic acid monomer. The polymorphic behavior of the nylon 11/MMT nanocomposites was investigated with X‐ray diffraction, transmission electron microscopy, and Fourier transform infrared with attenuated total reflectance. MMT induced and stabilized the δ‐crystalline form of nylon 11. The crystal structure of nylon 11 was transformed from a hexagonal δ‐form structure to a triclinic α‐form structure during the annealing process. Meanwhile, the hydrogen bonds in the nanocomposites also exhibited some differences from neat nylon 11 after annealing. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5483–5489, 2006     

Organomodification of montmorillonite and its effects on the properties of poly(butylene succinate) nanocomposites

The pristine sodium montmorillonite (MMT) was organically modified with hexadecyltrimethylammonium bromide (HTAB) at different contents. The organoclay was characterized by X‐ray diffraction (XRD), Fourier transform infrared spectroscopy, energy dispersive X‐ray techniques, and thermogravimetric analysis. Then, poly(butylene succinate) (PBS) nanocomposites were prepared by melt‐mixing process using maleic anhydride‐grafted PBS (PBS‐g‐MA) as compatibilizer. It was found that the mechanical properties of PBS nanocomposites filled with organoclay were apparently higher than that of the nanocomposite filled with MMT. This is attributed to the better filler–matrix interactions between PBS and the organoclay and the better filler dispersion. This is verifiable through the XRD, scanning electron microscopy, and transmission electron microscopy. The addition of PBS‐g‐MA further improved the mechanical properties. It was also found that our laboratory synthesized organoclay modified with HTAB has provided a better reinforcing efficiency when compared with the commercial octadecylamine‐modified organoclay. Besides that the thermal properties of PBS nanocomposites were studied through differential scanning calorimetry. POLYM. ENG. SCI., 2013. © 2013 Society of Plastics Engineers     

Preparation and properties of montmorillonite‐based polyimide nanocomposites

Montmorillonite (MMT)‐based polyimide (PI) nanocomposites were prepared via two‐stage polymerization of PI using polyamic acid (PAA). The clay was organically modified using various alkylammonium ions to examine the effect of changes in alkyl length on the intercalation spacing of both the treated clays and their hybrids with PAA and PI. The intercalation behavior of clay in the PI matrix and its thermal and mechanical properties were investigated as a function of clay concentration. The d‐spacing of organically modified MMT (O‐MMT) increased with increasing length of the alkylammonium chain. PI/O‐MMT hybrids form exfoliated nanocomposites at clay concentrations below 2 wt%, while they form intercalated nanocomposites together with some exfoliated ones at clay contents exceeding 4 wt%. Young's modulus increased rapidly to a clay loading of 2 wt%, and leveled off with further increases in clay loading. The tensile strength at break increased rapidly up to a clay loading of 1 wt%, and then decreased sharply, while the strain at break showed a monotonic decrease with increasing clay loading from 0 to 8 wt%. The storage modulus, E′, in the temperature range below the glass transition temperature T_g, generally increased with increasing clay content, except at the highest clay content of 8 wt%. Copyright © 2004 Society of Chemical Industry     

Intercalated clay structures and amorphous behavior of solution cast and melt pressed poly(ethylene oxide)–clay nanocomposites

The polymer nanocomposite (PNC) films consisted of poly(ethylene oxide) (PEO) and sodium cations montmorillonite (MMT) clay were prepared by aqueous solution casting and direct melt press compounding techniques, whereas the films of PEO with trimethyl octadecyl ammonium cations organo‐modified montmorillonite (OMMT) clay were formed by melt pressed technique. The clay concentrations in the nanocomposites used are 1, 2, 3, 5, 10, and 20 wt % of the PEO weight. The X‐ray diffraction patterns of these nanocomposites were measured in the angular range (2θ) of 3.8–30°. The values of basal spacing d₀₀₁ of MMT/OMMT, clay gallery width W_cg, d‐spacings of PEO crystal reflections d₁₂₀ and d₁₁₂, and their corresponding crystallite size L, and the peaks intensity I (counts) were determined for these nanocomposites. Results reveal that the nanocomposites have intercalated clay structures and the amount of intercalation increases with the increase of clay concentration. As compared to melt pressed PEO–MMT nanocomposites, the amount of clay intercalation is higher in aqueous solution cast nanocomposites. At 20 wt % MMT dispersion in PEO matrix, the solution cast PEO–MMT nanocomposite almost changes into amorphous phase. The melt press compounded PEO–OMMT films show more intercalation as compared to the PEO–MMT nanocomposites prepared by same technique. In melt pressed nanocomposites, the PEO crystalline phase significantly reduces when clay concentration exceeds 3 wt %, which is evidenced by the decrease in relative intensity of PEO principal crystalline peaks. The effect of interactions between the functional group (ethylene oxide) of PEO and layered sheets of clay on both the main crystalline peaks of PEO was separately analyzed using their XRD parameters in relation to structural conformations of these nanocomposites. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39898.     

Preparation and characterization of poly(butylene terephthalate) nanocomposites with various organoclays

Layered‐silicate‐based polymer–clay nanocomposite materials were prepared depending on the surface modification of montmorillonite (MMT). Nanocomposites consisting of poly(butylene terephthalate) (PBT) as a matrix and dispersed inorganic clay modified with cetyl pyridinium chloride (CPC), benzyl dimethyl N‐hexadecyl ammonium chloride, and hexadecyl trimethyl ammonium bromide by direct melt intercalation were studied. The organoclay loading was varied from 1 to 5 wt %. The organoclays were characterized with X‐ray diffraction (XRD) to compute the crystallographic spacing and with thermogravimetric analysis to study the thermal stability. Detailed investigations of the mechanical and thermal properties as well as a dispersion study by XRD of the PBT/clay nanocomposites were conducted. X‐ray scattering showed that the layers of organoclay were intercalated with intercalating agents. According to the results of a differential scanning calorimetry analysis, clay acted as a nucleating agent, affecting the crystallization. The PBT nanocomposites containing clay treated with CPC showed good mechanical properties because of intercalation into the polymer matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of anionically polymerized butadiene‐isoprene copolymer/clay nanocomposites

Butadiene‐isoprene copolymer/montmorillonite (BIR/MMT) nanocomposites were synthesized successfully via in situ anionic polymerization. The results of transmission electron microscopy and X‐ray diffractometer showed that the clay layers were exfoliated and high reaction temperature benefited the exfoliation of layers in BIR/MMT. The polymerization still exhibited “living” characteristics with the addition of organophilic montmorillonite (OMMT). However, the contents of 1,2‐polybutadiene and 3,4‐polyisoprene of the copolymer decreased with the addition of OMMT, because of its absorption effect on N,N,N′,N′‐tetramethylethanediamine as revealed by ¹H NMR. Moreover, it was observed that the glass‐transition temperature of the BIR/MMT nanocomposites also decreased when compared with the BIR copolymers. The thermal stability of the nanocomposites was improved, because of the barrier property of exfoliated clay layers. © 2006 Wiley Periodicals, Inc. J Appl PolymSci 102: 1167–1172, 2006     

Polystyrene nanocomposite materials by in situ polymerization into montmorillonite–vinyl monomer interlayers

A different series of new polystyrene–clay nanocomposites have been prepared by grafting polymerization of styrene with vinyl‐montmorillonite (MMT) clay. The synthesis was achieved through two steps. The first step is the modification of clay with the vinyl monomers, such as N,N‐dimethyl‐n‐octadecyl‐4‐vinylbenzyl‐ammonium chloride, n‐octadecyl‐4‐vinylbenzyl‐ammonium chloride, triphenyl‐4‐vinylbenzyl‐phosphonium chloride, and tri‐n‐butyl‐4‐vinylbenzyl‐phosphonium chloride. The second step is the polymerization of styrene with different ratios of vinyl‐MMT clay. The materials produced were characterized by different physical and chemical methods: (1) IR spectra, confirming the intercalation of the vinyl‐cation within the clay interlayers; (2) thermogravimetric analysis (TGA), showing higher thermal stability for PS–nanocomposites than polystyrene (PS) and higher thermal stability of nanocomposites with of phosphonium moieties than nanocomposites with ammonium moieties; (3) swelling measurements in different organic solvents, showing that the swelling degree in hydrophobic solvents increases as the clay ratio decreases; (4) X‐ray diffraction (XRD), illustrating that the nanocomposites were exfoliated at up to a 25 wt % of organoclay content; and (5) scanning electron microscopy (SEM), showing a complete dispersion of PS into clay galleries. Also, transmission electron microscopy (TEM) showed nanosize spherical particles of ～ 150–400 nm appearing in the images. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3739–3750, 2007