Accelerant‐promoted free radical polymerization of methacrylates by stabilized nitroxide unimolecular initiators: synthesis and characterization

BACKGROUND: This investigation evaluates the effectiveness of initiator adducts for living and controlled polymerization of methacrylates, crosslinking of dimethacrylates and thermal stabilities of the resulting polymers. Adducts of 2,2,6,6‐tetramethyl‐1‐piperidinyloxy with benzoyl peroxide and with azobisisobutyronitrile were prepared and evaluated as stabilized unimolecular initiators for the free radical polymerization of methacrylate monomers using sulfuric acid as catalyst. The monomers used were methyl methacrylate, triethylene glycol dimethacrylate (TEGDMA) and ethoxylated bisphenol A dimethacrylate (EBPADMA). RESULTS: Successful polymerization was achieved at 70 and 130 °C with reaction times ranging from 45 min to 120 h. The dispersity (D) of poly(methyl methacrylate) (PMMA) was 1.09–1.28. The livingness and extent of control over polymerization were confirmed with plots of M_n evolution as a function of monomer conversion and of the first‐order kinetics. The glass transition temperature (T_g) for PMMA was 123–128 °C. The degradation temperature (T_d) for PMMA was 350–410 °C. T_d for poly(TEGMA) was 250–310 °C and for poly(EBPADMA) was 320–390 °C. CONCLUSION: The initiators are suitable for free radical living and controlled polymerization of methacrylates and dimethacrylates under mild thermal and acid‐catalyzed conditions, yielding medium to high molecular weight polymers with low dispersity, high crosslinking and good thermal stability. Copyright © 2008 Society of Chemical Industry     

Resistivity of conductive polymer–coated fabric

Preparation of conductive polymer–coated fabrics was carried out by admicellar polymerization. By this method, a thin layer of conductive polymers (polypyrrole, polyaniline, and polythiophene) was formed on cotton and polyester fabrics by a surfactant template. The effects of monomer concentration, oxidant to monomer ratio, and addition of salt on the resistivity of the resulting fabrics were studied. The results showed that the apparent surface and volume resistivity decreased with an increase in monomer concentration in the range 5–15 mM, but was not strongly dependent on the oxidant to monomer ratio over the range of 1 : 1 to 2 : 1. Addition of 0.5M salt was found to reduce the resistivity significantly. The lowest resistivity obtained was with polypyrrole‐coated fabric, with resistivity around 10⁶ ohm. SEM micrographs of the treated fabric surface showed a filmlike polymer coating, confirming that the fabrics were successfully coated by admicellar polymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2629–2636, 2004     

Accelerated controlled radical polymerization of methacrylates

BACKGROUND: Nitroxide adducts 1,1‐ditertbutyl‐1‐(1‐methyl‐1‐cyanoethoxy)‐amine (AIBN/DBN), 1,1‐ditertbutyl‐1‐(benzoylperoxy)‐amine (BPO/DBN) and 2,2,6,6,‐tetramethyl‐4‐oxo‐1‐(1‐methyl‐1‐cyanoethoxy)‐piperidine (AIBN/4‐OXO‐TEMPO) were prepared and evaluated as stabilized unimolecular initiators for controlled radical polymerization of methacrylate monomers using sulfuric acid as an accelerating additive. Their effectiveness was evaluated from polymerization rates, molecular weight control and dispersity (D) of the polymers. Thermal stabilities of the polymers were also examined. The monomers used were methyl methacrylate, triethylene glycol dimethacrylate (TEGDMA) and ethoxylated bisphenol A dimethacrylate (EBPADMA). RESULTS: Polymerization was accomplished at 70 and 130 °C in 5 min to 144 h. The value of D of poly(methyl methacrylate) (PMMA) was 1.05–1.22. The glass transition temperature (T_g) for PMMA was 122–127 °C. The activity of the chain ends was established by chain extension and controlled polymerization was established by plotting M_n versus monomer conversion. First‐order kinetics in monomer consumption was established and an electron paramagnetic resonance study was conducted. Decomposition temperature (T_d) for PMMA was 360–380 °C, for poly(TEGDMA) was 300–380 °C and for poly(EBPADMA) was 360–440 °C. Photoinitiation without additive yielded no polymer. Thermal initiation by AIBN/4‐OXO‐TEMPO was the fastest. CONCLUSIONS: The initiators are applicable in low‐temperature additive‐enhanced controlled polymerization of methacylates and dimethacrylates, producing polymers with excellent attributes and a low value of D. Copyright © 2008 Society of Chemical Industry     

Fabrication of poly(methyl methacrylate)‐block‐poly(N‐isopropylacrylamide) amphiphilic diblock copolymer on silicon substrates via surface‐initiated reverse iodine transfer polymerization

Amphiphilic diblock copolymer on silicon substrates were synthesized via surface‐initiated reverse iodine transfer polymerization (RITP) technique. The silicon substrates (Si (111) surface) were modified with the azo groups, which were introduced by the treatment of Si (111) surface with 4,4′‐azobis (4‐cyanopentanoic acid). The poly(methyl methacrylate) (PMMA) were then prepared under RITP conditions from the Si (111) wafer. The synthesis of amphiphilic diblock copolymer was carried out on Si‐g‐PMMA substrate by sequential addition of monomer N‐isopropylacrylamide (NIPAM). The observed narrow molecular weight distributions (M_w/M_n), linear kinetic plots, and linear plots of molecular weight (M_n) versus monomer conversion indicate that the chain growth from the silicon substrates is a controlled process with a “living” characteristic. The ellipsometry and contact angle results indicated that the MMA had grafted from the surface of the silicon substrates successfully and the graft layer was well defined. The structure of the polymer and the ability to extend the chains were characterized and confirmed with the surface sensitive techniques such as X‐ray photoelectron spectroscopy and atomic force microscope. POLYM. ENG. SCI., 54:925–931, 2014. © 2013 Society of Plastics Engineers     

Synthesis and characterization of poly[4‐(2‐thiazolylazo)phenyl methacrylate]‐co‐poly(methyl methacrylate)

A new methacrylic monomer, 4‐(2‐thiazolylazo)phenylmethacrylate (TPMA) was synthesized. Copolymerization of the monomer with methyl methacrylate (MMA) was carried out by free radical polymerization in THF solution at 70 ± 0.5°C, using azobisisobutyronitrile (AIBN) as an initiator. The monomer TPMA and the copolymer poly(TPMA‐co‐MMA) were characterized by Fourier transform infrared (FTIR), ¹H nuclear magnetic resonance (NMR), and elemental analysis methods. The polydispersity index of the copolymer was determined using gel permeation chromatography (GPC). Thermogravimetric analysis (TGA) of the copolymer performed in nitrogen revealed that the copolymer was stable to 270°C. The glass transition temperature (T_g) of the copolymer was higher than that of PMMA. The copolymer with a pendent aromatic heterocyclic group can be dissolved in common organic solvents and shows a good film‐forming ability. Both the monomer TPMA and the copolymer poly (TPMA‐co‐MMA) have bright colors: orange and yellow, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2152–2157, 2007     

The potential of Cu(I)Cl/2,2′‐bipyridine catalysis in a triblock copolymer preparation by atom transfer radical polymerization

The ability of atom transfer radical polymerization (ATRP) in the sequential synthesis of triblock copolymers was examined using Cu(I)Cl/2,2′‐bipyridine catalysis at 110°C in toluene, starting from PMMA macroinitiators terminated with the C‐Br group. The PMMAs were prepared by living anionic or group transfer polymerization (GTP), followed by bromination of the respective active site with Br₂ or N‐bromosuccinimide (NBS). The yield of the terminal bromination in the products of both living polymerizations was 60–64% at best, compared with the yield of the bromination of 1‐methoxy‐(1‐trimethylsilyloxy)prop‐1‐ene (a model of the GTP active site) with NBS, as found by ¹H‐NMR. The PMMA macroinitiators prepared were utilized to start the sequential ATRP, finally affording PMMA‐b‐PBuA‐b‐PSt (M_n 69,100), PMMA‐b‐PSt‐b‐PBuA (M_n 21,300) and PMMA‐b‐PSt‐b‐PMMA (M_n 35,200), which have not yet been synthesized by ATRP. After the second block has been formed, the Br‐unterminated part of PMMA macroinitiator was removed by extraction or repeated precipitation. In the third (last) sequence polymerization, induction periods were observed. The first two triblock copolymers were free of precursors and have M_w/M_n values 1.5–1.6 (SEC). In the course of the last step of PMMA‐b‐PSt‐b‐PMMA synthesis, the content of the PMMA‐b‐PSt precursor slowly decreased with increasing MMA conversion. Still, at ≈90% MMA conversion, about 10–15% of the precursor remained in the product. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3514–3522, 2001     

Facile preparation of conductive paint made with polyaniline/dodecylbenzenesulfonic acid dispersion and poly(methyl methacrylate)

We investigated an easy way to prepare industrially a conductive paint made with polyaniline (PANI)/dodecylbenzenesulfonic acid (DBSA) dispersion and poly(methyl methacrylate) (PMMA) in organic media. First, water‐dispersible PANI doped with DBSA was chemically synthesized with aniline sulfate using ammonium persulfate in water, and the resulting PANI/DBSA was readily extracted from the reaction medium with a mixture of toluene and methyl ethyl ketone (MEK) (toluene:MEK = 1:1 (v/v)), which is useful for industrial applications. The obtained PANI/DBSA organic dispersion was mixed with PMMA organic solution to give the corresponding PANI/DBSA conductive paint containing PMMA. A film prepared with the resulting PANI/DBSA conductive paint was found to possess relatively good conductivity and low surface resistivity for a conductive paint utilized for an electrostatic discharge even at low PANI/DBSA content in the PANI/DBSA–PMMA composite film (the conductivity and the surface resistivity were 9.48 × 10^?4 S cm^?1 and 3.14 × 10⁶ Ω cm^?2, respectively, when the feed ratio of PANI/DBSA:PMMA was 1:39 (w/w)). Furthermore, it was found that the conductivity of the film composed of PANI/DBSA–PMMA composite can be readily and widely controlled by the PANI/DBSA content of the composite or by the amount of DBSA used during the PANI/DBSA synthesis. The highest conductivity of PANI/DBSA–PMMA composite film (7.84 × 10^?1 S cm^?1) was obtained when the feed ratio of PANI/DBSA:PMMA was 1:4 (w/w). Copyright © 2007 Society of Chemical Industry     

Effect of dopant mixture on the conductivity and thermal stability of polyaniline/nomex conductive fabric

Electrically conductive polyaniline (PANI)/[poly(m‐phenylene isophthalamide)] Nomex composite fabric was prepared by in situ polymerization of aniline doped by a mixture of hydrochloride (HCl) and various sulfonic acids such as benzenesulfonic acid (BSA), sulfosalicylic acid (SSA), and dodecylbenesulfonic acid (DBSA); their effect on conductivity and physical properties were then investigated. PANI/Nomex composite fabrics doped by a mixture of protonic acids exhibited higher conductivity than those doped by other single dopants such as camphorsulfonic acid (CSA), p‐toluenesulfonic acid (TSA), BSA, SSA, and HCl. The conductivity of PANI/Nomex fabrics especially doped by a mixture of HCl and DBSA was evenly maintained up to 100°C without depression of mechanical properties of Nomex. Their conductivity was also maintained under extension of the composite fabric. In addition, electrical conductivity of PANI/Nomex fabrics was highly increased by ultrasonic treatment, which facilitated better diffusion and adsorption of aniline by cavitation and vibration. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2245–2254, 2002     

Photo-induced controlled radical polymerization with new Photocatalyst

Photo-induced electron transfer reversible addition-fragmentation chain transfer (PET RAFT) of methyl methacrylate (MMA) was investigated at 25 °C with rose bengal (4,5,6,7-tetrachloro-2′,4′,5′,7′-tetraiodofluorescein) (RB) as photoredox catalyst under visible light irradiation. The traditional chain transfer agent 4-cyanopentanoic acid dithiobenzoate (CPADB) was employed in this study. The kinetic curve of the photo-induced PET RAFT polymerization exhibited a good linear behavior. The number average molecular weights (M_n,GPC) of the poly(methyl methacrylate) (PMMA) increased linearly with respect to monomer consumption and they were in good agreement with the calculated values (M_n,th). At the same time the molecular weight distribution (M_w/M_n) was narrow. Temporal control of PET RAFT polymerization of MMA was demonstrated by “ON/OFF” experiments. The resulting PMMA was characterized by ¹H–NMR, and GPC. The resultant PMMA could be used as macro-chain transfer agents for the PET RAFT radical polymerization. The chain experiments were successfully carried out and the living characteristics were demonstrated. The probable mechanism was discussed.     

Polymerization of methyl methacrylate with Nickel(II)α‐benzoinoxime complex

Polymerizations of methyl methacrylate (MMA) monomer initiated by a novel Ni(II)α‐benzoinoxime complex have been achieved under homogeneous conditions in the 25–60°C temperature range. The activity for polymerization increases with reaction temperature and by carrying out the polymerization in solution of low‐polarity solvents without any induction time. The obtained polymers have weight‐average molecular weights about 10⁵ and slight broad polydispersity indexes (2.2 ≤ M_w/M_n ≤ 3.3). Dependence of rate constants polymerization and decomposition of initiator (k_app and k_d, respectively) on temperature was investigated and activation parameters were computed from Arrhenius plot. ¹H‐NMR analysis of PMMA revealed a syndio‐rich atactic microstructure in agreement with conventional radical process. Radical scavenger TEMPO effect together with microstructure and molecular weight distributions data supported that the polymerization proceed via free radical mechanism. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Fe‐mediated SET‐LRP of MMA and St in the presence of air

In this work, well‐defined homopolymers of methyl methacrylate (PMMA) and styrene (PSt) were prepared via single‐electron‐transfer living radical polymerization using CCl₄ as initiator and Fe(0)/N, N, N′,N′‐tetramethyl‐1,2‐ethanediamine as catalyst. The polymerization was conducted at 25 °C in N,N‐dimethylformamide in the presence of air. It proceeded in a ‘living’ manner, as indicated by the first‐order kinetics behavior, and the linear increase of the number‐average molecular weight (M_{n, GPC}) with conversion was close to the theoretical M_{n, theory}. Solvent and additives have a profound effect on the polymerization. In addition, the PMMA and PSt obtained remained of low dispersity. The chain‐end functionality of the obtained homopolymer of PMMA was characterized by proton nuclear magnetic resonance. A block copolymer of P(MMA‐block‐St) was achieved by using the obtained PMMA as macroinitiator. The living characteristics were further demonstrated by chain extension experiments. Copyright © 2012 Society of Chemical Industry     

Shielding and dielectric properties of sulfonic acid‐doped π‐conjugated polymer in 8.2–12.4 GHz frequency range

This article deals with dielectric and electromagnetic interference shielding properties of the polyaniline doped with dodecyl benzene sulfonic acid (DBSA) synthesized by microemulsion polymerization of aniline in aqueous solution of DBSA. Dielectric constant and shielding effectiveness due to absorption (SE_A) were calculated using S‐parameter obtained from the vector network analyzer in 8.2–12.4 GHz frequency range. Maximum SE_A of 26 dB (>99%) was achieved for polymer sample. The real part ε′ of complex permittivity shows small variation, whereas the imaginary part ε″ is found to decrease with the increase in frequency. Different formulations have been performed to see the effect of monomer to dopant ratio on intrinsic properties of polyaniline. Further characterization of polymer was carried out by UV–visible and thermal gravimetric analysis, whereas the conductivity measurements were carried out by the four‐probe method.© 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Graft copolymerization of methyl methacrylate onto rubber‐wood fiber using H2O2 and Fe2+ as an initiator system

Methyl methacrylate (MMA) was successfully grafted onto rubber‐wood fiber in a free‐radical solution polymerization initiated by ferrous ion and hydrogen peroxide. The effects of the reaction parameters (reaction temperature, reaction period, influence of hydrogen peroxide, ferrous ammonium sulfate, and monomer concentrations) were investigated. The grafting percentage showed dependency on H₂O₂, Fe²⁺, and monomer concentrations, as well as reaction temperature and reaction period. The optimum reaction temperature was determined to be about 60°C and the reaction period was 60 min. The optimum concentration of H₂O₂ was 0.03M and optimum amounts of Fe²⁺ and MMA were 0.26 mmol and 2.36 × 10^?2 mol, respectively. Poly(methyl methacrylate) (PMMA) homopolymer was removed from the graft copolymer by Soxhlet extractor using acetone. The presence of PMMA on the fiber was shown by FT‐IR spectroscopy and gravimetric analysis. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2499–2503, 2003     

Synthesis of PMMA‐PTHF‐PMMA and PMMA‐PTHF‐PST linear and star block copolymers

Combination of cationic, redox free radical, and thermal free radical polymerizations was performed to obtain linear and star polytetramethylene oxide (poly‐THF)‐polymethyl methacrylate (PMMA)/polystyrene (PSt) multiblock copolymers. Cationic polymerization of THF was initiated by the mixture of AgSbF₆ and bis(4,4′ bromo‐methyl benzoyl) peroxide (BBP) or bis (3,5,3′,5′ dibromomethyl benzoyl) peroxide (BDBP) at 20°C to obtain linear and star poly‐THF initiators with M_w varying from 7,500 to 59,000 Da. Poly‐THF samples with hydroxyl ends were used in the methyl methacrylate (MMA) polymerization in the presence of Ce(IV) salt at 40°C to obtain poly(THF‐b‐MMA) block copolymers containing the peroxide group in the middle. Poly(MMA‐b‐THF) linear and star block copolymers having the peroxide group in the chain were used in the polymerization of methyl methacrylate (MMA) and styrene (St) at 80°C to obtain PMMA‐b‐PTHF‐b‐PMMA and PMMA‐b‐PTHF‐b‐PSt linear and star multiblock copolymers. Polymers obtained were characterizated by GPC, FT‐IR, DSC, TGA, ¹H‐NMR, and ¹³C‐NMR techniques and the fractional precipitation method. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 219–226, 2004     

N-[Salicylidene-1,2-ethanediaminoethyl]-2-bromoisobutyramide as initiator for atom transfer radical polymerization and surface-initiated ATRP of methyl methacrylate on copper

N-[Salicylidene-1,2-ethanediaminoethyl]-2-bromoisobutyramide (SEB) was synthesized and characterized by elemental analysis, FT-IR and ¹H NMR. It had been successfully used as a bidentate initiator for the atom transfer radical polymerization (ATRP) of methyl methacrylate with CuBr/2,2′-bipyridine as the catalyst and N,N-dimethylformamide as the solvent at 70 °C. The kinetics was first order in monomer and the number-average molecular weight of the polymer increased linearly with monomer conversion, indicating the ‘living’/controlled nature of the polymerization. The polymerization reached high conversions producing polymers with a low molecular weight distribution (M _w/M _n = 1.34). The obtained poly(methylmethacrylate) (PMMA) functionalized with salicylidene-1,2-ethanediaminoethyl and ω-Br as the end groups were characterized by FT-IR spectroscopy. They can be used as macroinitiators for chain-extension reaction. Then, PMMA coatings were grafted from copper substrates by surface-initiated ATRP from a surface-bound SEB initiator. The electrochemical impedance spectroscopy measurements and potentiodynamic electrochemical experiments confirmed the successful grafting of the polymer coatings. Greatly improved short-term anticorrosive properties for PMMA modified electrodes were demonstrated by substantially increased resistance of the film for a period of 24 h as compared to bare copper.     

Monomers for adhesive polymers, 8a crosslinking polymerization of selected N‐substituted bis(acrylamide)s for dental filling materials

The free‐radical polymerization of bis‐(N‐ethylacrylamido)‐ethylenglycol ( I ), N,N′‐dimethyl‐1,6‐bis (acrylamido)‐hexan ( II ), and N,N′‐diethyl‐1,3‐bis(acrylamido)‐propan ( III ) were investigated. The cross‐linking polymerization was followed in bulk by using the ampoules technique and gravimetry. Polymerizations exhibited an abnormal kinetic behavior. For the monomer II , for example, the reaction order to 2,2′‐ azobisisobutyronitril (AIBN) initiator of 1.28, and the polymerization overall activation energy of 151 kJ/mol between 50 and 75°C were determined. The increasing temperature and decreasing initiator concentration resulted in an increase of double bonds consumption in the formed polymer network. At 75°C the residual unsaturation was under 2%, compared with 9.9% at 50°C. The monomer conversion‐time dependences were complemented also with differential scanning calorimetry (DSC) recording the heat released during polymerization. The extension of peak time with decreasing the instant heat flow rate at this point sort the studied bis(acrylamide)s according the reactivity in the following sequence: monomer III > I > II . The polymer samples sol–gel analyses in ethanol allowed the determination of the molecular weight M_c between the network crosslinks. The presence of microgel particles at the very beginning of polymerization and the changes in chain conformation with temperature we consider as the way in which was affected the polymerization kinetics of these monomers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanistic studies in tackified acrylic emulsion pressure sensitive adhesives

Twenty‐three wt % aqueous tackifier dispersion based on glycerol ester abietic acid (T_g = 64°C, M_w = 940) was added to emulsion polymer 50/32/15/3 poly(2‐ethyl hexyl acrylate‐co‐vinyl acetate‐co‐dioctyl maleate‐co‐acrylic acid) pressure sensitive adhesive (PSA). From these latices, 25 μm thick films were cast. The films were dried at 25°C for 24 h or at 121°C for 5 min. Dynamic mechanical analysis (DMA) of the films included measuring elastic modulus (G′) and damping factor (tan δ). Under the above drying conditions, the films did not produce significant differences in their DMA and PSA properties as measured by loop tack, peel, and shear holding power. DMA of the tackified acrylic film showed thermodynamic miscibility between the tackifier and polymer regardless of the drying conditions. Microgels formed during emulsion polymerization of the acrylic PSA brought inherent weakness to the tackified film properties. In the neat acrylic PSA film, these discrete networks entangled with the uncrosslinked chains while in the tackified film, these networks could not form entanglements due to the increased molecular weight between entanglements for the uncrosslinked chains. This lack of network entanglements caused shear holding power of the tackified acrylic PSA film to be 4× lower than that of the neat acrylic PSA film. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1965–1976, 2000     

Zinc‐based catalyst for the ring‐opening polymerization of cyclic esters

A zinc‐based catalyst zinc bis[bis(trimethylsilyl)amide] was used for the polymerization of cyclic esters including L ‐lactide (L ‐LA) and 2‐methyl‐2‐carboxyl‐propylene carbonate (MBC). The polymerization of L ‐lactide in THF could be carried out successfully under mild conditions in very short time by using the zinc catalyst and alcohols as the initiators. Kinetic study in solution polymerization prooved the polymerization has high monomer conversion degree close to 100% and the molecular weight of the resulting polyester has linear increase with the increase of [M]₀ /[I] (molar ratio of monomer to initiator). Sequential polymerization of L ‐LA and MBC in THF also showed high MBC conversion of 94% with a narrow molecualr weight maintained, indicating a living nature of this polymerization. The zinc catalyst system has also been used for the L ‐LA bulk polymerization with a high monomer conversion. ¹³C NMR indicated the polymer possesses high regioregularity and the minor regioirregular component was owing to the D ‐LA in the monomer inserted into the polymer mainchain during the transesterifcation. Interaction between monomer and zinc catalyst has been found to be a key factor to sustain a homogenous solution during the initiating procedure. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Surface modification of polyester and polyamide fabrics by low frequency plasma polymerization of acrylic acid

In this study, the surface characteristics of polyester and polyamide fabrics were changed by plasma polymerization technique utilizing acrylic acid as precursor. This monomer was used to produce hydrophilic materials with extended absorbency. The hydrophilicity, total wrinkle recovery angle (WRA°) and breaking strength of the fabrics were determined prior and after plasma polymerization treatment. The modification of surfaces was carried out at low pressure (<100 Pa) and low temperature (<50°C) plasma conditions. The effects of exposure time and discharge power parameters were optimized by comparing properties of the fabrics before and after plasma polymerization treatments. It was shown that two sides of polyester fabric samples were treated equally and homogeneously in plasma reactor. For polyester fabrics, the minimum wetting time, 0.5 s, was observed at two plasma processing parameters of 10 W–45 min and 10 W–20 min, where untreated fabric has a wetting time of 6 s. For polyester fabrics, the maximum value was obtained at 60 W–5 min with the wrinkle recovery angle of 306° where the untreated fabric has 290°. The optimum plasma conditions for polyamide fabrics were determined as 30 W–45 min where 2 s wetting time was observed. Wrinkle recovery angle of untreated polyamide fabric was 264°. In this study, after plasma polymerization of acrylic acid, wrinkle recovery angle values were increased by 13%. No significant change was observed in breaking strength of both fabrics after plasma treatment. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2318–2322, 2007     

Synthesis of 1,3‐benzodioxole end‐functionalized polymers via reversible addition–fragmentation chain transfer polymerization

Reversible addition–fragmentation chain transfer (RAFT) polymerization of styrene was carried out in the presence of a novel RAFT reagent, bearing 1,3‐benzodioxole group, benzo [1,3]dioxole‐5‐carbodithioic acid benzo [1,3]dioxol‐5‐ylmethyl ester (BDCB), to prepare end‐functionalized polystyrene. The polymerization results showed that RAFT polymerization of styrene could be well controlled. Number–average molecular weight (M_n(GPC)) increased linearly with monomer conversion, and molecular weight distributions were narrow (M_w/M_n < 1.4). The successful reaction of chain extension and analysis of ¹H NMR spectra confirmed the existence of the functional 1,3‐benzodioxole group at the chain‐end of polystyrene. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99: 3535–3539, 2006