Effects of extrusion conditions on the properties of recycled poly(ethylene terephthalate)/nanoclay nanocomposites prepared by a twin‐screw extruder

The effects of extrusion conditions on the mechanical properties of recycled poly(ethylene terephthalate) (rPET)/clay nanocomposites were studied. Nanocomposites of recycled PET containing 2.5 and 5.0 wt % of montmorillonite modified with organophilic quaternary ammonium salt (DELLITE 67G) were prepared by melt compounding using a corotating twin‐screw type extruder at two different screw rotation speeds: 250 and 150 rpm. The highest value of Young's modulus was found for low screw rotation speed (150 rpm). Morphological analysis using transmission electron microscopy (TEM) revealed the presence of fully exfoliated clay platelets in samples prepared at 150 rpm. It was concluded that the screw rotation speed should be optimized when preparing recycled PET/clay nanocomposites by melt compounding. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Recycled poly(ethylene terephthalate)/layered silicate nanocomposites: morphology and tensile mechanical properties

Various amounts (1, 3 and 5 wt%) of a non-modified natural montmorillonite clay (Cloisite^® Na⁺) or of an ion-exchanged clay modified with quaternary ammonium salt (Cloisite^® 25A) were dispersed in a recycled poly(ethylene terephthalate) matrix (rPET) by a melt intercalation process. Microphotographs of composite fracture surfaces bring evidence that particles of Cloisite^® 25A are much better dispersed in the rPET matrix than those of Cloisite^® Na⁺. Moreover, WAXS measurements indicate that the lamellar periodicity of Cloisite^® 25A is increased in the composites, which evidences intercalation of rPET between silicate layers (lamellae) of the clay. In the case of Cloisite^® Na⁺, a very small thickening of lamellae due to mixing with rPET indicates only minute intercalation.Uniaxial tensile tests show that both clays increase the modulus of the rPET composites; more effective Cloisite^® 25A accounts for a 30% increase at loading of 5 wt%. Yield strength remains practically unaffected by the used fractions of the clays while tensile strength slightly decreases with the clay content; in parallel, strain at break dramatically drops. Tensile compliance of the composites is virtually independent of applied stress up to 26 MPa. Essential part of the compliance corresponds to the elastic time-independent component, while the viscoelastic component is low corresponding only to a few percent of the compliance even at relatively high stresses. The compliance of the composites is only slightly lower than that of the neat rPET, the reinforcing effect of Cloisite^® 25A being somewhat stronger. Both clays have beneficial effect on the dimensional stability of the composites since—in contrast to the neat rPET—the creep rate does not rise at long creep periods.     

Synthesis and characterization of poly(ethylene terephthalate)/attapulgite nanocomposites

A kind of clay with fibrous morphology, attapulgite (AT), was used to prepare poly (ethylene terephthalate) (PET)/AT nanocomposites via in situ polymerization. Attapulgite was modified with Hexadecyltriphenylphosphonium bromide and silane coupling agent (3‐glycidoxypropltrimethoxysilane) to increase the dispersion of clay particles in polymer matrix and the interaction between clay particles and polymer matrix. FTIR and TGA test of the organic‐AT particles investigated the thermal stability and the loading quantity of organic reagents. XRD patterns and SEM micrographs showed that the organic modification was processed on the surface of rod‐like crystals and did not shift the crystal structure of silicate. For PET/AT nanocomposites, it was revealed in TEM that the fibrous clay can be well dispersed in polymer matrix with the rod‐like crystals in the range of nanometer scale. The diameter of rod‐like crystal is about 20 nm and the length is near to 500 nm. The addition of the clay particles can enhance the thermal stability and crystallization rate of PET. With the addition of AT in PET matrix, the flexural modulus of those composites was also increased markedly. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1279–1286, 2007     

Toughening of recycled poly(ethylene terephthalate) with clay‐compatibilized rubber phase

Recycled bottle‐grade PET (rPET) is a valuable low‐cost polymeric material. However, enhancement of its mechanical properties is necessary for many applications. This work is focused on clay‐reinforced/compatibilized rPET/elastomer system. Although the clay addition to various rPET/elastomer blends caused a remarkable refinement of structure, more pronounced for clay with less polar modification, both a gain or decrease in strength and toughness occurred, whereas an increase in modulus was found for all systems. This is a consequence of simultaneous complex affecting many parameters by clay and both antagonistic and synergistic combination of respective effects. Best results were found for low contents of EPR rubber and its preblending with clay. The presented results indicate that a suitable combination of nanosilicates with rubber can lead to rPET materials with fairly enhanced properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

TPV及PP-g-MAH对回收PET的改性研究

以马来酸酐接枝聚丙烯(PP-g-MAH)为相容剂,回收聚对苯二甲酸乙二醇酯(rPET)为基体材料,动态硫化热塑性弹性体(TPV)为增韧材料,制备了rPET/TPV/PP-g-MAH共混物。用SEM、DMA及DSC分析了TPV及PP-g-MAH对rPET断面结构、储能模量和结晶性能的影响,并测试了共混物的力学性能。结果表明:加入9.95%TPV后,rPET/TPV共混物的熔融温度下降了2.33℃,结晶温度提高了2.82℃,断裂伸长率及缺口冲击强度明显提高,弯曲强度和拉伸强度略有下降;加入PP-g-MAH后,TPV球状粒子嵌入rPET基体材料中,共混物的相容性提高,储能模量明显增大,刚性增强,弯曲强度和拉伸强度有所提高;与纯rPET相比,含1.8%PP-g-MAH的rPET/TPV/PP-g-MAH共混物的断裂伸长率提高了129.06%,缺口冲击强度提高了47.02%。     

Preparation and characteristics of nitrile rubber (NBR) nanocomposites based on organophilic layered clay

The effect of clay modification on organo‐montmorillonite/NBR nanocomposites has been studied. Organo‐montmorillonite/NBR nanocomposites were prepared through a melt intercalation process. NBR nanocomposites were characterized by X‐ray diffraction (XRD), transmission electron microscopy (TEM), dynamic mechanical thermal analysis (DMTA) and a universal testing machine (UTM). XRD showed that the basal spacing in the clay increased, which means that the NBR matrix was intercalated in the clay layer galleries. On TEM images, organo‐montmorillonite (MMT) particles were clearly observed, having been exfoliated into nanoscale layers of about 10–20 nm thickness from their original 40 µm particle size. These layers were uniformly dispersed in the NBR matrix. The DMTA test showed that for these nanocomposites the plateau modulus and glass transition temperature (T_g) increased with respect to the corresponding values of pure NBR (without clay). UTM test showed that the nanocomposites had superior mechanical properties, ie strength and modulus. These improved properties are due to the nanoscale effects and strong interactions between the NBR matrix and the clay interface. Copyright © 2003 Society of Chemical Industry     

Enhancement of the thermal stability,mechanical properties and morphologies of recycled PVC/clay nanocomposites

Summary Recycled PVC/clay nanocomposites were prepared by melt mixing of recycled PVCs and modified clays. Characterization of the nanostructure of the nanocomposites was carried out using wide angle X-ray diffraction (WAXD) and transmission electron microscopy(TEM). In case of 10wt.%, the characteristic peak of modified clay was perfectly disappeared, because of aids of plasticizers as co-intercalator. Thermal stability was evaluated from the thermal decomposition behaviors and linear dimension changes by TGA and TMA system. Coefficients of thermal expansion of the nanocomposites were also observed from TMA analysis. Dynamic mechanical properties were evaluated using DMA system. The thermal and mechanical properties of the nanocomposites were improved simultaneously for varied clay loadings, 1,3,5,10wt.%, compared to recycled PVC. Especially, the storage modulus of the nanocomposites with 10wt.% clay loading was increased 11 times compared to that of recycled PVC.     

Morphological influence on mechanical characterization of ethylene‐vinyl acetate copolymer–clay nanocomposites

Ethylene‐vinyl acetate copolymer (EVA)/montmorillonite (MMT) clay nanocomposites with varying degree of intercalation and exfoliation have been prepared using direct melt blending techniques with various degrees of polarity (9, 18, and 28 wt% vinyl acetate [VA]) and two different types of clay modification. Morphological characterization using wide‐angle X‐ray scattering (WAXS) and transmission electron microscopy (TEM) have indicated/confirmed the presence of intercalation and/or a combination of intercalation and exfoliation existing in the nanocomposites. The effects of these (simple intercalation or mixed intercalation/exfoliation) states and the effect of changing matrix polarity (by changing VA wt% content) on the nanocomposite mechanical behavior were studied. There is sufficient evidence from the mechanical studies that 1) the presence of nanoclay can simultaneously improve modulus and strength of the nanocomposites, and 2) the mechanical properties are a combined function of the clay concentration and the nanocomposite morphology (due to the VA wt% and presence of clay). It is shown here that interrelation between the VA wt% content and the clay exfoliation affects the mechanical properties in a way that has a positive and increasing slope with increasing loading of clay. It is shown that a clear understanding of the nanocomposite mechanical properties can be obtained from its morphological analysis. POLYM. ENG. SCI., 45:889–897, 2005. © 2005 Society of Plastics Engineers     

Morphology and properties of nanocomposites from organoclays with reduced cation exchange capacity

Organoclays with different levels of reduction in the original cation exchange capacity (CEC) were prepared to characterize the morphology and Young's modulus of their melt‐processed nanocomposites made from nylon 6 (PA‐6) and polypropylene/polypropylene grafted with maleic anhydride (PP/PP‐g‐MA). Wide‐angle X‐ray scattering (WAXS), transmission electron microscopy (TEM), and Young's modulus data are reported. Three different levels of CEC reduction were obtained; WAXS analysis and percentage loss on ignition (LOI) calculations for these organoclays showed a reduction in both the intergallery spacing and in the amount of organic modifier contained in the clay with CEC reduction. The morphology and modulus results show that these reduced‐CEC organoclays led to lower exfoliation and modulus enhancement for both PA‐6 and PP/PP‐g‐MA nanocomposites. The results may be influenced by differences in layer charge and charge distribution that could have been produced during the charge reduction process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Organic interfacial tailoring of styrene butadiene rubber–clay nanocomposites prepared by latex compounding method

The styrene butadiene rubber (SBR)–clay nanocompounds were prepared by the latex compounding method, and then hexadecyl trimethyl ammonium bromide (C16) and 3‐aminopropyl triethoxy silane (KH550) were added into these nanocompounds on a two‐roll mill to prepare nanocomposites with strong interfacial interaction. The structure and properties of SBR–clay nanocomposites were carefully studied by X‐ray diffraction (XRD) studies, transmission electron microscopy (TEM), Rubber Process Analyzer (RPA), and mechanical testing. Compared with unmodified nanocomposites, the dispersion structure of modified SBR–clay nanocomposites is better with part rubber‐intercalated or part modifier‐intercalated structure. The tensile strength and the modulus at 300% elongation of modified SBR–clay nanocomposites are higher than three times of those of unmodified nanocomposites, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1826–1833, 2007     

Effects of N,N′-Ethylenebis(stearamide) on the Properties of Poly(ethylene terephthalate)/Organo-montmorillonite Nanocomposite

Poly(ethylene terephthalate)/organo-montmorillonite (PET/OMMT) nanocomposites were melt-compounded using twin screw extruder followed by injection molding. N,N′-ethylenebis(stearamide) (EBS) was selected as a dispersing agent to improve the dispersibility and exfoliation of OMMT clay in PET matrix. Morphological properties of the PET/OMMT nanocomposites were examined by using X-ray diffraction analysis, transmission electron microscopy and atomic force microscopy. Thermal properties of the nanocomposites were characterized by using dynamic mechanical thermal analysis. It was found that the OMMT are well dispersed and exfoliated in the presence of EBS. Remarkable enhancement in impact strength and storage modulus of PET/OMMT was achieved by the addition of EBS.     

Poly(ethylene terephthalate) nanocomposite fibers with new organomica via in situ intercalation

Poly(ethylene terephthalate) (PET) nanocomposites with a newly synthesized organomica (C₁₆BIMD‐Mica) were obtained by using the in situ interlayer polycondensation of ethylene glycol with dimethylterephthalic acid. The PET hybrids were melt‐spun to produce monofilaments with various organoclay contents and draw ratios. The thermomechanical properties and morphologies of the PET hybrid fibers were determined using differential scanning calorimetry, thermogravimetric analysis, wide angle X‐ray diffraction, electron microscopy (SEM and TEM), and a universal tensile machine. The XRD analyses and TEM micrographs showed that the levels of exfoliation and intercalation could be controlled by varying the clay content. The thermomechanical properties of the PET hybrid fibers were found to be better than those of pure PET fibers. POLYM. ENG. SCI., 47:1820–1826, 2007. © 2007 Society of Plastics Engineers     

相容剂对rPET/mLLDPE共混物性能的影响

以回收聚对苯二甲酸乙二醇酯(rPET)为基体材料,茂金属线型低密度聚乙烯(mLLDPE)为共混材料,马来酸酐接枝线型低密度聚乙烯(LLDPE-g-MAH)、丙烯酸酯复合接枝苯乙烯-丁二烯弹性体为相容剂,制备了rPET/mLLDPE共混物。采用DSC和SEM分析了相容剂对共混物结晶性能及断面结构的影响,并检测了共混物的力学性能。结果表明:mLLDPE的加入使得rPET/mLLDPE共混物的熔体结晶峰向右移动,结晶温度提高了29.03℃;相容剂的加入使得共混物中rPET的玻璃化转变温度向低温方向移动,rPET与mLLDPE相容性增强;含3%LLDPE-g-MAH的rPET/mLLDPE共混物中,MAH基团与rPET中的羟基发生接枝反应,相界面模糊,rPET与mLLDPE界面黏结力增强,与纯rPET相比,其断裂伸长率提高了93.73%,缺口冲击强度提高了54.6%。     

Recycling of poly(ethylene terephthalate) as polymer‐polymer composites

Microfibrillar reinforced composites (MFC) comprising an isotropic matrix from a lower melting polymer reinforced by microfibrils of a higher melting polymer were manufactured under industrially relevant conditions and processed via injection molding. Low density polyethylene (LDPE) (matrix) and recycled poly(ethylene terephthalate) (PET) (reinforcing material) from bottles were melt blended (in 30/70 and 50/50 PET/LDPE wt ratio) and extruded, followed by continuous drawing, pelletizing and injection molding of dogbone samples. Samples of each stage of MFC manufacturing and processing were characterized by means of scanning electron microscopy (SEM), wide‐angle X‐ray scattering (WAXS), dynamic mechanical thermal analysis (DMTA), and mechanical testing. SEM and WAXS showed that the extruded blend is isotropic but becomes highly oriented after drawing, being converted into a polymer‐polymer composite upon injection molding at temperatures below the melting temperature of PET. This MFC is characterized by an isotropic LDPE matrix reinforced by randomly distributed PET microfibrils, as concluded from the WAXS patterns and SEM observations. The MFC dogbone samples show impressive mechanical properties—the elastic modulus is about 10 times higher than that of LDPE and about three times higher than reinforced LDPE with glass spheres, approaching the modulus of LDPE reinforced with 30 wt% short‐glass fibers (GF). The tensile strength is at least two times higher than that of LDPE or of reinforced LDPE with glass spheres, approaching that of reinforced LDPE with 30 wt% GF. The impact strength of LDPE increases by 50% after reinforcement with PET. It is concluded that: (i) the MFC approach can be applied in industrially relevant conditions using various blend partners, and (ii) the MFC concept represents an attractive alternative for recycling of PET as well as other polymers.     

Supercritical carbon dioxide (scCO2) dispersion of poly(ethylene terephthalate)/clay nanocomposites: Structural,mechanical, thermal,and barrier properties

Dispersed poly(ethylene terephthalate) (PET)/clay nanocomposites can lead to materials with superior barrier and mechanical properties. PET/clay nanocomposites were prepared by melting extrusion of PET with as‐received or supercritical carbon dioxide (scCO₂) predispersed Cloisite^® 30B (30B). The predispersion of 30B was assessed by WAXD, SEM, and TGA, and results indicated that scCO₂ processing could predisperse 30B and the surface modification of the clay was preserved after processing. The structure of PET/30B nanocomposites was investigated by WAXD and TEM confirming that PET has penetrated into the clays inter‐galleries and the predispersed clays lead to improved interfacial interaction and homogenous clay dispersion. Both tensile strength and Young's modulus were improved by 12.1% and 24.9% respectively, as incorporating of 3 wt % of scCO₂ processed clay. Differential scanning calorimetry (DSC) results indicated that clay particles served as nucleation agent could increase the crystallinity whereas had no impact on melting process. In addition, with the addition of 1 wt % of predispersed clay, a significant reduction of oxygen permeation (～33%) was achieved at 23 °C and the maximum reduction (44%) was achieved by adding 3 wt % processed clay. Moreover, we confirmed the effect of temperature on the permeation of PET/30B nanocomposites depended both on the Arrhenius behavior of the organic phases and tortuous path effects, where improved clay dispersion resulted in a higher effective activation energy. Moreover, the transparency of PET matrix was preserved for all nanocomposites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44779.     

Effect of clay on properties of polyimide‐clay nanocomposites

Effect of clay on mechanical, thermal, moisture absorption, and dielectric properties of polyimide‐clay nanocomposites was investigated. Nanocomposites of polyimide (ODA‐BSAA) hybridized with two modified clay (PK‐802 and PK‐805) were synthesized for comparison. The silicate layers in the polymer matrix were intercalated/exfoliated as confirmed by wide‐angle X‐ray diffraction and transmission electron microscopy. Thermal stability, moisture absorption, and storage modulus for these nanocomposites are improved as hybridized clay increases. Reduced dielectric constants due to the hybridization of layered silicates are observed at frequencies of 1 kHz–1 MHz and temperatures of 35–150°C. The tetrahedrally substituted smectite (PK‐805) resulted in higher mechanical strength and dielectric constants than those of octahedrally substituted smectite (PK‐802), which could be attributed to their stronger ionic bonding between clay layer and polymer matrix. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 318–324, 2007     

Morphology and mechanical and viscoelastic properties of rubbery epoxy/organoclay montmorillonite nanocomposites

The morphology and mechanical and viscoelastic properties of rubbery epoxy/organoclay montmorillonite (MMT) nanocomposites were investigated with wide‐angle X‐ray scattering (WAXS), transmission electron microscopy (TEM), tensile testing, and dynamic mechanical thermal analysis. An ultrasonicator was used to apply external shearing forces to disperse the silicate clay layers in the epoxy matrix. The first step of the nanocomposite preparation consisted of swelling MMT in a curing agent, that is, an aliphatic diamine based on a polyoxypropylene backbone with a low viscosity for better diffusion into the intragalleries. Then, the epoxy prepolymer was added to the mixture. Better dispersion and intercalation of the nanoclay in the matrix were expected. The organic modification of MMT with octadecylammonium ions led to an increase in the initial d‐spacing (the [d₀₀₁] peak) from 14.4 to 28.5 Å, as determined by WAXS; this indicated the occurrence of an intercalation. The addition of 5 phr MMTC18 (MMT after the modification) to the epoxy matrix resulted in a finer dispersion, as evidenced by the disappearance of the diffraction peak in the WAXS pattern and TEM images. The mechanical and viscoelastic properties were improved for both MMT and MMTC18 nanocomposites, but they were more pronounced for the modified ones. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 103: 3547–3552, 2007     

Poly(ethylene terephthalate) nanocomposites by in situ interlayer polymerization: the thermo-mechanical properties and morphology of the hybrid fibers

Nanocomposites of poly(ethylene terephthalate) (PET) with C₁₂PPh-MMT as an organoclay were synthesized by using the in situ interlayer polymerization approach. The PET nanocomposites were melt-spun at different organoclay contents and different draw ratios to produce monofilaments. The thermo-mechanical properties and the morphologies of the PET nanocomposites were examined by using a differential scanning calorimeter, a thermogravimetric analyzer, a wide angle X-ray diffactometer, scanning and transmission electron microscopes, and a universal tensile machine. Some of the clay particles were well dispersed in the PET matrix, and some of them were agglomerated at a size level of greater than approximately 10 nm. The thermal stability and the tensile mechanical properties of the PET hybrid fibers increased with increasing clay content at a DR=1. However, the values of the ultimate tensile strength and the initial modulus of the hybrid fibers decreased markedly with increasing DR from 1 to 16.     

Effects of compatibilizer,compounding method,extrusion parameters,and nanofiller loading in clay‐reinforced recycled HDPE/PET nanocomposites

Nanocomposites based on recycled high density polyethylene (rHDPE), recycled polyethylene terephthalate (rPET), and organoclay (C10A) were made using twin screw extruder followed by hot pressing. The independent effects of polymer/clay compatibility, preparation method, extrusion parameters, and clay loadings were investigated. Ethylene‐glycidyl methacrylate could effectively improve the compatibilization of immiscible rHDPE/rPET blend with clay, which confirmed by the good polymers‐clay adherence and domain size reduction obtained in scanning electron microscopy images. Although intercalated structures were observed in the composites made by one‐step compounding, in the composites prepared by two‐step extrusion method, enhanced dispersion of clay in polymer blend was found from X‐ray diffraction results. Higher extrusion temperature and intermediate speed of rotation (90 rpm) appeared to increase the mechanical properties due to improvement of nanofiller dispersion in matrix. Results showed that the stiffness increased whereas tensile and impact strength decreased with clay content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42287.     

Preparation and properties of styrene–butadiene rubber based nanocomposites: The influence of the structural and processing parameters

Rubber‐based nanocomposites were prepared with octadecyl amine modified sodium montmorillonite clay and styrene–butadiene rubber with different styrene contents (15, 23, and 40%). The solvent used to prepare the nanocomposites, the cure conditions, and the cure system were also varied to determine their effect on the properties of the nanocomposites. All the composites were characterized with X‐ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, and transmission electron microscopy (TEM). The XRD studies revealed exfoliation for the modified clay–rubber composites. The TEM photomicrographs showed a uniform distribution of the modified clay in the rubber matrix. The thickness of the particles in the exfoliated composites was around 10–15 nm. Although the FTIR study of the unmodified and modified clays showed extra peaks due to the intercalation of the amine chains into the gallery, the spectra for the rubber–clay nanocomposites were almost the same because of the presence of a very small amount of clay in the rubber matrix. All the modified clay–rubber nanocomposites displayed improved mechanical strength. The styrene content of the rubber had a pronounced effect on the properties of the nanocomposites. With increasing styrene content, the improvement in the properties was greater. Dicumyl peroxide and sulfur cure systems displayed similar strength, but higher elongation and slightly lower modulus values were obtained with the sulfur cure system. The curing of the samples at four different durations at 160°C showed that the cure time affected the properties. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 698–709, 2004