The enhanced mechanical properties of a covalently bound chitosan‐multiwalled carbon nanotube nanocomposite

In the present work, chitosan (CS)‐grafted multiwalled carbon nanotube (MWCNT) nanocomposites were prepared via covalently bonded CS onto MWCNTs that had weight fractions of MWCNTs ranging from 0.1 to 3.0 wt % by a simple method of solution casting. The structure, morphology, and mechanical properties of the films were investigated by Fourier transform infrared spectroscopy, field emission scanning electron microscopy, optical microscopy, wide‐angle X‐ray diffraction, contact angle, and tensile testing. The results indicated that the CS chains were attached onto the MWCNTs successfully via covalent linkages. More interestingly, the MWCNTs provided a matrix that facilitated the crystallization of CS. Compared with the pure CS, the tensile strength and Young's modulus of the nanocomposites were enhanced significantly from 39.6 to 105.6 MPa and from 2.01 to 4.22 GPa with an increase in the MWCNT loading level from 0 to 3.0 wt %, respectively. The improvement in the tensile strength and modulus were ascribed to the uniform dispersion of MWCNTs covalently linked to the CS matrix. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Natural rubber/multiwalled carbon nanotube composites developed with a combined self-assembly and latex compounding technique

Carbon nanotubes (CNTs), with their high aspect ratio and exceptionally high mechanical properties, are excellent fillers for composite reinforcement if they are uniformly dispersed without aggregation. Combining the latex compounding and self-assembly techniques, we prepared a novel natural rubber (NR)/multiwalled carbon nanotube (MWCNT) composite. Before self-assembly, the MWCNTs were treated with mixed acid to ensure that the MWCNTs were negatively charged under an alkaline environment. The structure of the MWCNTs was tested with Fourier transform infrared spectroscopy. The properties of composites with different MWCNT loadings were characterized with transmission electron microscopy, scanning electron microscopy, thermogravimetric analysis, and tensile testing. The results indicate that the MWCNTs were homogeneously distributed throughout the NR matrix as single tubes and had good interfacial adhesion with the NR phase when the MWCNT loading was less than 3 wt %. In particular, the addition of the MWCNT led to a remarkable reinforcement in the tensile strength, with a peak value of 31.4 MPa for an MWCNT content of 2 wt %, compared to the pure prevulcanized NR (tensile strength = 21.9 MPa). The nanocomposites reinforced with MWCNTs should have wide applications because of the notable improvement in these important properties. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Thermosetting polyurethane multiwalled carbon nanotube composites

Thermosetting polyurethane (PU) multi‐walled carbon nanotube (MWCNT) nanocomposites at loadings up to 1 wt % were prepared via an addition polymerization reaction. The morphology of the nanocomposites and degree of dispersion of the MWCNTs was studied using a combination of scanning electron microscopy (SEM), high resolution transmission electron microscopy (HRTEM) and wide angle X‐ray diffraction (WAXD), and revealed the nanotubes to be highly dispersed in the PU matrix. Addition of just 0.1 wt % MWCNTs resulted in significant enhancements in stiffness, strength and toughness. Increases in Young's modulus, % elongation at break and ultimate tensile strength of 561, 302 and 397% were measured for the nanocomposites compared to the unfilled PU. The effect of the MWCNTs on the modulus of the PU was evaluated using the Rule of Mixtures, Krenchel and Halpin‐Tsai models. Only the Halpin‐Tsai model applied to high aspect ratio nanotubes was in good agreement with the modulus values determined experimentally. Strong interfacial shear stress was found between PU chains and nanotubes, up to 439 MPa, calculated using a modified Kelly‐Tyson model. Evidence for strong interfacial interactions was obtained from the Raman spectra of both the precursor materials and nanocomposites. When the MWCNTs were added to the isophorone diisocyanate an up‐shift of 14 cm^?1 and on average 40 cm^?1 was obtained for the position of the carbon‐hydrogen (C? H) out‐of plane bending (766 cm^?1) and isocyanate symmetric stretch (1420 cm^?1) modes respectively. Moreover, an up‐shift of 24 cm^?1 was recorded for the nanotube tangential mode (G‐band) for the 1.0 wt % nanocomposite because of the compressive forces of the PU matrix acting on the MWCNTs. The dynamic mechanical (DMA) properties of the PU thermoset and the nanocomposites were measured as a function of temperature. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and properties of polyurethane/multiwalled carbon nanotube nanocomposites by a spray drying process

A spray drying approach has been used to prepare polyurethane/multiwalled carbon nanotube (PU/MWCNT) composites. By using this method, the MWCNTs can be dispersed homogeneously in the PU matrix in an attempt to improve the mechanical properties of the nanocomposites. The morphology of the resulting PU/MWCNT composites was investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). SEM and TEM observations illustrate that the MWCNTs are dispersed finely and uniformly in the PU matrix. X‐ray diffraction results indicate that the microphase separation structure of the PU is slightly affected by the presence of the MWCNTs. The mechanical properties such as tensile strength, tensile modulus, elongation at break, and hardness of the nanocomposites were studied. The electrical and the thermal conductivity of the nanocomposites were also evaluated. The results show that both the electrical and the thermal conductivity increase with the increase of MWCNT loading. In addition, the percolation threshold value of the PU composites is significantly reduced to about 5 wt % because of the high aspect ratio of carbon nanotubes and exclusive effect of latex particles of PU emulsion in dispersion. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Interfacial crystallization of low‐crystallinity elastomer incorporated by multi‐walled carbon nanotubes: Mechanical reinforcement,structural evolution and enhanced thermal stability

In this paper, we report interfacial crystallization in olefin block copolymer (OBC) with low crystallinity incorporated by multi‐walled carbon nanotubes (MWCNTs). A hybrid shish‐kebab (HSK) superstructure in nanocomposites is observed that MWCNTs act as central shish and OBC crystals grow perpendicular to the nanotubes axis. The mechanical properties of nanocomposites are significantly improved with incorporation of MWCNTs. The most ideal reinforcing and toughening effect is both observed in nanocomposites with MWCNTs content of 1 wt % that can increase tensile strength by 122% as well as elongation at break by 36%. Efficient load transfer are confirmed with in‐situ Raman spectra that G’ band of MWCNTs in OBC matrix exhibit a downshifting trend and symmetric broadening of line shape which reveals additional macroscale strain from axial extension of MWCNTs in nanocomposites, thus suggesting a certain load is carried by HSK superstructure. The structural evolution of OBC and nanocomposites are investigated by in‐situ wide‐angle X‐Ray Diffraction (WAXD). The Herman's orientation factor of nanocomposites with 2 wt % MWCNTs incorporation is lower than that of neat matrix at mall and intermediate strains, indicating a heterogeneous stress distribution and low compliance of HSK superstructure, which is consistent with in‐situ Raman results. Moreover, the nanocomposites presents significantly enhanced thermal stability. The onset decomposition temperature of nanocomposites with 3 wt % MWCNTs can be 60.2°C higher than that of neat OBC. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42368.     

Fabrication of polystyrene/multiwalled carbon nanotube composite films synthesized by in situ microemulsion polymerization

A microemulsion polymerization method was used to achieve better compatibility between polystyrene (PS)/multiwalled carbon nanotubes (MWCNTs) nanocomposites and the host PS matrix to form films with excellent electrical and thermal properties. The films were prepared by embedding the PS/MWCNTs nanocomposite into the PS matrix. The MWCNTs were functionalized with PS nanoparticles to avoid the phase separation problem between the filler and host matrix and to enhance the good dispersibility of MWCNTs in the PS host matrix. The confirmation of the synthesis was analyzed by Fourier transform infrared spectroscopy, nuclear magnetic resonance, and Raman spectroscopy. The variation effect of the PS‐linking density on the MWCNT was revealed by scanning electron microscopy and transmission electron microscopy. An enhancement of the thermal and mechanical properties was revealed by thermal gravimetric analysis, differential scanning colorimetric analysis, and dynamic mechanical analysis. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Study on the Reusability of Multiwalled Carbon Nanotubes in Biodegradable Chitosan Nanocomposites

The mechanical properties, water absorption, biodegradation, multiwalled carbon nanotubes (MWCNTs) recovery and reusability of chitosan/oxidized MWCNTs nanocomposites were investigated. The highest Young's modulus (E) was obtained by the nanocomposites with 0.1 wt.% MWCNTs, while further increase of MWCNTs loading decreases the tensile strength (TS) and E. The water absorption and degradation rate of the nanocomposites were decreased by the loading of MWCNTs; 89.7% of MWCNTs were recovered by physical base separation. Thermogravimetric analysis (TGA), scanning electron microscopy (SEM) and tensile test results showed that the recovered MWCNTs displayed properties similar to the oxidized MWCNTs, suggesting the possibility of reuse and recycle.     

Mechanical and thermal properties of polyphenylene sulfide/multiwalled carbon nanotube composites

Polyphenylene sulfide (PPS)/multiwalled carbon nanotube (MWCNT) composites were prepared using a melt‐blending procedure combining twin‐screw extrusion with centrifugal premixing. A homogeneous dispersion of MWCNTs throughout the matrix was revealed by scanning electron microscopy for the nanocomposites with MWCNT contents ranging from 0.5 to 8.0 wt %. The mechanical properties of PPS were markedly enhanced by the incorporation of MWCNTs. Halpin‐Tsai equations, modified with an efficiency factor, were used to model the elastic properties of the nanocomposites. The calculated modulus showed good agreement with the experimental data. The presence of the MWCNTs exhibited both promotion and retardation effects on the crystallization of PPS. The competition between these two effects results in an unusual change of the degree of crystallinity with increasing MWCNT content. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Investigation on flame retardancy and rheological and thermomechanical characterisation of multiwall carbon nanotube reinforced nanocomposites

Abstract

In the present work, the influence of multiwalled carbon nanotubes (MWCNTs) on the flame retardancy and rheological, thermal and mechanical properties of polybutilen terephthalate (PBT) and polypropylene (PP) matrixes has been investigated. The carbon nanotube content in the thermoplastic materials was 2 and 5?wt‐%. The nanocomposites were obtained by diluting a masterbatch containing 20?wt‐% nanotubes using a twin‐screw extruder and the thermal properties were analysed by differential scanning calorimetry and thermogravimetric analysis; thermomechanical properties were determined by dynamic mechanical thermal analysis and the rheological behaviour was studied by a Thermo Haake Microcompounder. The results concerning the flame retardancy show that the MWCNTs are not equally effective as flame retardants in PP and PBT. The ignition time is increased only for PBT whereas the extinguishing time is decreased for PP and PBT. The reinforcement of the thermoplastics with multiwall carbon nanotubes is improved regarding the mechanical and thermal properties of the nanocomposites compared to pristine materials and the behaviour of thermoplastic nanocomposites regarding fire retardancy depends on the nature of the polymeric matrix.     

Toughening of cycloaliphatic epoxy resin by multiwalled carbon nanotubes

The toughness of cycloaliphatic epoxy resin 3,4‐epoxycyclohexylmethyl‐3′,4′‐epoxycyclohexane carboxylate (ERL‐4221) has been improved by using multiwalled carbon nanotubes (MWCNTs) treated by mixed acids. The MWCNT/ERL‐4221 composites were characterized by Raman spectroscopy and their mechanical properties were investigated. A significant increase in the tensile strength of the composite from 31.9 to 55.9 MPa was obtained by adding only 0.05 wt % of MWCNTs. And a loading of 0.5 wt % MWCNTs resulted in an optimum tensile strength and cracking energy, 62.0 MPa and 490 N cm, respectively. Investigation on the morphology of fracture surface of the composites by field emission scanning electron microscopy demonstrated the crack pinning‐front bowing and bridging mechanisms of toughening. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Alumina‐filled polystyrene micro‐ and nanocomposites prepared by melt mixing with and without latex precompounding: Structure and properties

Alumina fillers were incorporated in polystyrene (PS) in 4.5 wt % by melt blending with and without latex precompounding. Latex precompounding was used for the latex‐mediated predispersion of the alumina particles. The related masterbatch was produced by mixing PS latex with water dispersible boehmite alumina in various particle sizes followed by drying. The dispersion of the alumina in the PS was studied by transmission and scanning electron microscopy (TEM and SEM, respectively). The mechanical and thermomechanical properties of the PS composites were determined in uniaxial tensile, dynamic‐mechanical thermal analysis (DMTA), and short‐time creep tests performed at various temperatures. In addition, the melt flow of the composites was characterized in a plate/plate rheometer. It was found that direct melt mixing of the alumina with PS resulted in micro‐, whereas the masterbatch technique in nanocomposites. The stiffness and resistance to creep (summarized in master curves) of the nanocomposites were improved compared to those of the microcomposites. The properties of the composites were upgraded by decreasing nominal size of the water dispersible alumina. The preparation technique and the size of the alumina particles affected the tensile strength, melt viscosity, and heat distortion temperature in lesser extent than the stiffness and thus compliance data. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

PS/POE/功能化石墨烯纳米复合材料的制备和性能研究

利用马来酸酐接枝聚烯烃(POE-g-MAH)弹性体为增韧剂,乙二胺功能化石墨烯(G-EDA)为纳米填料,经熔融共混法制备了聚苯乙烯(PS)/POE-g-MAH/G-EDA纳米复合材料,并对填料和所得纳米复合材料的结构和性能进行了全面的表征。红外光谱(FTIR)、扫描电子显微镜(SEM)、力学性能、维卡软化温度和熔融指数测试表明:乙二胺(EDA)已成功接枝于石墨烯的表面上;共混过程中,POE-g-MAH的酐基与EDA的氨基发生反应改善了共混体系的界面相容性;G-EDA在熔融共混过程中均匀分散于PS基体中;随着G-EDA含量的增加,复合材料的拉伸强度先增大后降低,当G-EDA质量分数为0.5%时,复合材料的拉伸强度达到最大值,比PS/POE-g-MAH提高了12.3%,比纯PS提高了15.5%;而当G-EDA质量分数为0.75%时,复合材料的冲击强度达到最大值,比PS/POE-g-MAH提高了22%,比纯PS提高了22.4%。因此,当G-EDA的质量分数在0.5%~0.75%之间时,复合材料的综合力学性能最好。G-EDA的加入,纳米复合材料的邵氏A硬度、维卡软化温度等都逐渐增大,而熔融指数逐渐降低。     

Effects of Nickel Oxide (NiO) nanoparticles on the performance characteristics of the jatropha oil based alkyd and epoxy blends

Plant oil based alkyd resin was prepared from jatropha oil and blended with epoxy resin. Subsequently, alkyd/epoxy/NiO nanocomposites with different wt % of NiO nanoparticles have been prepared by mechanical mixing of the designed components. The structure, morphology, and performance characteristics of the nanocomposites were studied by UV‐visible spectroscopy, Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X‐ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and universal testing machine (UTM). The alkyd/epoxy/NiO nanocomposites showed the gradual increase in thermal stability with increasing NiO content. With 3 wt % NiO content the tensile strength of the nanocomposite increased by 19 MPa (more than twofold) when compared with the pristine polymer. Limiting oxygen index (LOI) value of the nanocomposites indicate that the incorporation of NiO nanoparticles even in 1 wt % can greatly improves the flame retardant property of the nanocomposites. This study confirms the strong influence of NiO nanoparticles on the thermal, mechanical, and flame retardant properties of the alkyd/epoxy/NiO nanocomposites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41490.     

Rubber/LDH nanocomposites by solution blending

The rubber nanocomposites containing ethylene vinyl acetate (EVA) having 60 wt % of vinyl acetate content and organomodified layered double hydroxide (DS‐LDH) as nanofiller have been prepared by solution intercalation method and characterized. The XRD and TEM analysis demonstrate the formation of completely exfoliated EVA/DS‐LDH nanocomposites for 1 wt % filler loading followed by partially exfoliated structure for 5–8 wt % of DS‐LDH content. EVA/DS‐LDH nanocomposites show improved mechanical properties such as tensile strength (TS) and elongation at break (EB) in comparison with neat EVA. The maximum value of TS (5.1 MPa) is noted for 3 wt % of DS‐LDH content with respect to TS value of pure EVA (2.6 MPa). The data from thermogravimetric analysis show the improvement in thermal stability of the nanocomposites by ≈15°C with respect to neat EVA. Limiting oxygen index measurements show that the nanocomposites act as good flame retardant materials. Swelling property analysis shows improved solvent resistance behavior of the nanocomposites (1, 3, and 5 wt % DS‐LDH content) compared with neat EVA‐60. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of carbon nanotube on PA6/ECO composites: Morphology development,rheological, and thermal properties

Thermoplastic elastomer (TPE) nanocomposites based on polyamide‐6 (PA6)/poly(epichlorohydrin‐co‐ethylene oxide) (ECO)/multiwall carbon nanotube (MWCNTs) were prepared by melt compounding process. Different weight ratios of ECO (20, 40, and 60 wt %) and two kinds of functionalized and non‐functionalized MWCNTs were employed to fabricate the nanocomposites. The morphological, rheological, and mechanical properties of MWCNTs‐filled PA6/ECO blends were studied. The scanning electron microscopy of PA6/ECO blends showed that the elastomer particles, ECO, are well‐dispersed within the PA6 matrix. The significant improvement in the dispersibility of the carboxylated carbon nanotubes (COOH‐MWCNTs) compared to that of non‐functionalized MWCNTs (non‐MWCNTs) was confirmed by transmission electron microscopy images. The tensile modulus of samples improved with the addition of both types of MWCNTs. However, the effect of COOH‐MWCNTs was much more pronounced in improving mechanical properties of PA6/ECO TPE nanocomposites. Crystallization results demonstrated that the MWCNTs act as a nucleation agent of the crystallization process resulted in increased crystallization temperature (T_c) in nanocomposites. Rheological characterization in the linear viscoelastic region showed that complex viscosity and a non‐terminal storage modulus significantly increased with incorporation of both types of MWCNTs particularly at low frequency region. The increase of rheological properties was more pronounced in the presence of carboxylic (COOH) functional groups, in the other words by addition of COOH‐MWCNTs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45977.     

Effects of multiwall carbon nanotubes on the thermal and mechanical properties of medium density polyethylene matrix nanocomposites produced by a mechanical milling method

Medium‐density polyethylene/multiwall carbon nanotube (MDPE/MWCNT) nanocomposites were produced by a mechanical milling method using a high‐energy ball mill. The MDPE and MWCNTs were added to the ball mill at a constant 20:1 weight ratio of ball/powders and milled for 10 h to obtain polyethylene matrix nanocomposites reinforced with 0.5, 1, 2.5, and 5 weight percent of MWCNTs. To clarify the role of both MWCNT content and milling time on the morphology of MDPE, some nanocomposite samples were investigated by using a scanning electron microscope. To evaluate the role of milling on the microstructure of the nanocomposites, very thin films of MDPE/MWCNTs were prepared and studied by transmission electron microscopy. Thermal behavior of these nanocomposites was investigated by using differential scanning calorimetry (DSC). Standard tensile samples were produced by compression molding. The dependence of the tensile properties of MDPE on both milling time and MWCNT content was studied by using a tensile test. The results of the microscopic evaluations showed that the milling process could be a suitable method for producing MDPE/MWCNT nanocomposites. The addition of carbon nanotubes to MDPE caused a change in its morphology at constant milling parameters. The results of the DSC tests showed that the crystallization temperature of MDPE increased as MWCNTs were added, although no dependency was observed as milling time increased. Crystallization index changed from 50 to 55% as MWCNT content increased from 0 to 5%. The results of the tensile tests showed that both the Young's modulus and the yield strength of MDPE increased as MWCNTs were added. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers     

Improvement in properties of multiwalled carbon nanotube/polypropylene nanocomposites through homogeneous dispersion with the aid of surfactants

The effects of different surfactants on the properties of multiwalled carbon nanotubes/polypropylene (MWCNT/PP) nanocomposites prepared by a melt mixing method have been investigated. Sodium dodecyl sulfate (SDS) and sodium dodecylbenzene sulfonate (NaDDBS) were used as a means of noncovalent functionalization of MWCNTs to help them to be dispersed uniformly into the PP matrix. The effects of these surfactant‐treated MWCNTs on morphological, rheological, thermal, crystalline, mechanical, and electrical properties of MWCNT/PP composites were studied using field emission scanning electron microscopy, optical microscopy, rheometry, tensile, and electrical conductivity tests. It was found that the surfactant‐treatment and micromixing resulted in a great improvement in the state of dispersion of MWCNTs in the polymer matrix, leading to a significant enhancement of Young's modulus and tensile strength of the composites. For example, with the addition of only 2 wt % of SDS‐treated and NaDDBS‐treated MWCNTs, the Young's modulus of PP increased by 61.1 and 86.1%, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical behaviors of ethylene/styrene interpolymer compatibilized polystyrene/polyethylene blends

In this study, ethylene/styrene interpolymer was used as a compatibilizer for the blends of polystyrene (PS) and high‐density polyethylene (HDPE). The mechanical properties including tensile and impact properties and morphology of the blends were investigated by means of uniaxial tension, instrumented falling‐weight impact measurements, and scanning electron microscopy. Tensile tests showed that the yield strength of the PS/HDPE/ESI blends decreases considerably with increasing HDPE content. However, the elongation at break of the blends tended to increase significantly with increasing HDPE content. The excellent tensile ductility of the HDPE‐rich blends resulted from shield yielding of the matrix. Izod and Charpy impact measurements indicated that the impact strength of the blends increases slowly with HDPE content up to 40 wt %; thereafter, it increases sharply with increasing HDPE content. The impact energy of the HDPE‐rich blends exceeded that of pure HDPE, implying that the HDPE polymer can be further toughened by the incorporation of brittle PS minor phase in the presence of ESI compatibilizer. The correlation between the impact property and morphology of the blends is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4001–4007, 2007     

Mechanical and morphological properties of lyocell blends: Comparison with lyocell nanocomposites (I)

The mechanical properties and morphologies of polyblends of lyocell with three different fillers are compared. Poly(vinyl alcohol) (PVA), poly(vinyl alcohol‐co‐ethylene) (EVOH), and poly(acrylic acid‐co‐maleic acid) (PAM) were used as fillers in blends with lyocell produced through solution blending. The variations of their properties with polymer matrix filler content are discussed. The ultimate tensile strength of the PVA/lyocell blend is highest for a blend lyocell content of 30 wt %, and decreases as the lyocell content is increased up to 40 wt %. The ultimate tensile strengths of the EVOH/lyocell and PAM/lyocell blends are highest for a lyocell loading of 20 wt %, and decrease with the increasing filler content. The variations in the initial moduli of the blends with filler content are similar. Of the three blend systems, the blends with PVA exhibit the best tensile properties. Lyocell/organoclay hybrid films were prepared by the solution intercalation method, using dodecyltriphenylphosphonium–Mica (C₁₂PPh‐ Mica) as the organoclay. The variation of the mechanical tensile properties of the hybrids with the matrix polymer organoclay content was examined. These properties were found to be optimal for an organoclay content of up to 5 wt %. Even polymers with low organoclay contents exhibited better mechanical properties than pure lyocell. The addition of organoclay to lyocell to produce nanocomposite films was found to be less effective in improving its ultimate tensile strength than blending lyocell with the polymers. However, the initial moduli of the nanocomposites were found to be higher than those of the polyblend films. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Structure and properties of multi‐walled carbon nanotubes/polyethylene nanocomposites synthesized by in situ polymerization with supported Cp2ZrCl2 catalyst

Multi‐walled carbon nanotubes (MWCNTs)/polyethylene (PE) nanocomposites were prepared via in situ polymerization with MWCNTs supported Bis‐ (cyclopentadienyl) zirconium dichloride (Cp₂ZrCl₂) catalyst. X‐ray photoelectron spectroscopy (XPS) and field emission scanning electron microscope (FESEM) results implied that Cp₂ZrCl₂ catalyst was immobilized in the surface of the MWCNTs supports via a bridge of methylaluminoxane (MAO). The efficient dispersion of MWCNTs in PE matrix and the strong compressive forces associated with PE on the MWCNTs were demonstrated by means of transmission electron microscope (TEM), FESEM and Raman spectra. With introducing 0.2 wt% MWCNTs, both the tensile strength and elongation of MWCNTs/PE nanocomposite were improved by factors of 1.6 (from 29 to 45 MPa) and 1.5 (from 909% to 1360%) comparing with the pure PE, respectively. Morphology observation of fractured surface revealed that the PE firmly adhered to the nanotubes, which was responsible for the significant improvement of the mechanical properties of nanocomposites. Thermal stabilities of the nanocomposites were significantly improved. In addition, the MWCNTs/PE nanocomposites showed very high ultraviolet (UV) shielding property, which could increase photooxidative stability of the PE. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers