Rapid living free‐radical polymerization of methyl acrylate under 60Co γ‐ray irradiation at room temperature

Rapid living free‐radical polymerization of methyl acrylate under ⁶⁰Co γ‐ray irradiation in the presence of benzyl 1H‐imidazole‐1‐carbodithioate at room temperature is reported. The results showed that the polymerization is a fast living process, and that the molecular weight of the polymer is as high as 39 600 g mol^?1 at 68 % conversion with M_w/M_n = 1.09 within 68 min. The polymerization rate was markedly influenced by the structures of thiocarbonylthio compounds. Copyright © 2004 Society of Chemical Industry     

Influence of γ‐irradiation on poly(methyl methacrylate)

Poly(methyl methacrylate) (PMMA) was γ‐irradiated (5–20 kGy) by a ¹³⁷Cs source at room temperature in air. The changes in the molecular structure attributed to γ‐irradiation were studied by mechanical testing (flexure and hardness), size‐exclusion chromatography, differential scanning calorimetry, thermal gravimetric analysis, and both Fourier transform infrared and solution ¹³C‐NMR spectroscopy. Scanning electron microscopy was used to investigate the influence of the dose of γ rays on the fracture behavior of PMMA. The experimental results confirm that the PMMA degradation process involves chain scission. It was also observed that PMMA presents a brittle fracture mechanism and modifications in the color, becoming yellowish. The mechanical property curves show a similar pattern when the γ‐radiation dose increases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 886–895, 2002     

Synthesis and thermal properties of polystyrene/montmorillonite nanocomposites by γ‐ray radiation polymerization

Polystyrene/montmorillonite nanocomposites were prepared by γ‐ray radiation polymerization. X‐ray diffraction and high‐resolution transmission electron microscopy confirmed that polystyrene (PS) could be easily inserted between the sheets of montmorillonite (MMT) to form intercalated nanocomposites. In these PS/MMT nanocomposites, the distance between the sheets of MMT was barely influenced by varying the content of the MMT. Thermal stabilities of the samples were studied by thermal gravimetric analysis and differential scanning calorimetry. The glass‐transition temperature of PS/MMT nanocomposites was obviously higher than that of the pure PS. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1692–1696, 2003     

Atom‐transfer radical polymerization of methyl methacrylate with α,α′‐dichloroxylene/CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine initiation system under microwave irradiation

The atom‐transfer radical polymerization (ATRP) of methyl methacrylate (MMA), using α,α′‐dichloroxylene as initiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine as catalyst was successfully carried out under microwave irradiation (MI). The polymerization of MMA under MI showed linear first‐order rate plots, a linear increase of the number‐average molecular weight with conversion, and low polydispersities, which indicated that the ATRP of MMA was controlled. Using the same experimental conditions, the apparent rate constant (k) under MI (k = 7.6 × 10^?4 s^?1) was higher than that under conventional heating (k = 5.3 × 10^?5 s^?1). © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2189–2195, 2004     

Characterization of mechanical properties of γAl2O3 dispersed epoxy resin cured by γ‐ray radiation

Epoxy resins are widely utilized as high performance thermosetting resins for many industrial applications, but they are characterized by relatively low toughness. Incorporation of rigid inorganics is suggested to improve the mechanical properties of epoxy resins. An attempt is made to disperse nanosized γ‐Al₂O₃ particles into diglycidyl ether of bisphenol A epoxy resins for the improvement of the mechanical properties. These hybrid epoxy–alumina composites are prepared using by the γ‐ray curing technique conducted at 100 kGy under nitrogen at room temperature. The composites are characterized by determining the gel content, flexural strength, Youngis modulus, and toughness at room temperature using scanning electron microscopy and FTIR studies. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1898–1903, 2004     

Homogeneous graft copolymerization of chitosan with butyl acrylate by γ‐irradiation via a 6‐O‐maleoyl‐N‐phthaloyl‐chitosan intermediate

The graft copolymerization of butyl acrylate (BA) onto chitosan was tried via a new protection‐graft‐deprotection procedure. About 6‐O‐maleoyl‐N‐phthaloyl‐chitosan was synthesized and characterized by Fourier transform infrared spectra analysis (FT‐IR) and ¹H‐NMR. Because the intermediate 6‐O‐maleoyl‐N‐phthaloyl‐chitosan was soluble in organic solvents, the graft copolymerization was carried out in a homogeneous system. Grafting was initiated by γ‐irradiation. The graft extent was dependent on the irradiation dose and the concentration of BA monomer, and copolymers with grafting above 100% were readily prepared. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 489–493, 2006     

Homogeneous graft copolymerization of chitosan with methyl methacrylate by γ‐irradiation via a phthaloylchitosan intermediate

The graft copolymerization of methyl methacrylate (MMA) onto chitosan was tried via a new protection‐graft‐deprotection procedure. Because the intermediate phthaloylchitosan was soluble in organic solvents, the graft copolymerization was carried out in a homogeneous system. Grafting was initiated by γ‐irradiation. The graft percentage extent was dependent on the irradiation dose and the concentration of MMA monomer, and copolymers with grafting above 100 % were readily prepared. The graft copolymers exhibited a high affinity not only for aqueous acid but also for some organic solvents. Differential scanning calorimetry measurements revealed the presence of a glass transition phenomenon, which could be ascribed to the poly(methyl methacrylate) side‐chains. Copyright © 2004 Society of Chemical Industry     

Synthesis of ω‐amino‐α‐phenylcarbonate alkanes and their polymerization to [n]‐polyurethanes

Aliphatic [n]‐polyurethanes have recently been synthesized from ω‐isocyanato‐α‐alkanols or, more traditionally, by cationic ring‐opening polymerization of cyclourethanes or by the Bu₂Sn(OMe)₂‐promoted polycondensation of ω‐hydroxy‐α‐O‐phenylurethane alkanes. For the latter procedures, the conditions employed do not seem to be suitable for highly functionalized monomers. In contrast, the polymerization of ω‐amino‐α‐phenylcarbonate alkanes is expected to occur under milder conditions. ω‐Amino‐α‐phenylcarbonate alkanes have been synthesized from 6‐aminohexanol (1) and 3‐aminopropanol (6). The procedure involves the N‐Boc protection of the amino group, followed by activation of the alcohol. Removal of the N‐Boc affords the corresponding ω‐amino‐1‐O‐phenyloxycarbonyloxyalkane hydrochlorides. Other oligomeric comonomers between 1 and 6 have been prepared. The polymerization of these precursors takes place in the absence of metal catalysts to afford the corresponding linear and regioregular [n]‐polyurethanes. The procedure described is useful for the preparation of stable ω‐amino‐α‐phenylcarbonate alkane derivatives, which possess varied chain lengths between the terminal functions. These monomers yield [n]‐polyurethanes having various structures starting from just two aminoalkanols. The polyurethanes were obtained in high yields, with reasonable molecular weight and polydispersity values, and they were characterized spectroscopically and thermally. These studies reveal constitutionally uniform structures that are free of carbonate or urea linkages. Copyright © 2010 Society of Chemical Industry     

Surface modification of aramid fibers with γ‐ray radiation for improving interfacial bonding strength with epoxy resin

Co⁶⁰ γ‐ray radiation as a simple and convenient method for surface modification of Armos aramid fibers was introduced in this article. Two kinds of gas mediums, N₂ and air, were chosen to modify aramid fiber surface by γ‐ray irradiation. After fiber surface treatment, the interlaminar shear strength values of aramid/epoxy composites were enhanced by about 17.7 and 15.8%, respectively. Surface elements of aramid fibers were determined by XPS, the analysis of which showed that the ratio of oxygen/carbon was increased. The crystalline state of aramid fibers was determined by X‐ray diffraction instrument. The surface topography of fibers was analyzed by atomic force microscopy and scanning electron microscope. The degree of surface roughness and the wettability of fiber surface were both enhanced by γ‐ray radiation. The results indicated that γ‐ray irradiation technique, which is a suitable way of batch process for industrialization, can significantly improve the surface properties of aramid fibers reinforced epoxy resin matrix composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and characterization of CdS and CdS/polyacrylonitrile nanocomposites by γ‐irradiation and emulsion polymerization

CdS and CdS/polyacrylonitrile (PAN) nanocomposites were prepared by γ‐irradiation and emulsion polymerization. The CdS and CdS/PAN nanocomposites were characterized by powder X‐ray diffraction, infrared spectroscopy, Fourier transform Raman spectroscopy, transmission electron microscopy, X‐ray diffraction, X‐ray photoelectron spectroscopy, and thermal analysis (thermogravimetric analysis/dynamic thermal analysis). In photoluminescence spectroscopy analysis, the maximum peak of CdS/PAN nanocomposites prepared by γ‐irradiation and emulsion polymerization was at about 485 nm, whereas the maximum peak of CdS nanocomposites was at about 460 nm. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2335–2342, 2004     

Dissolution of latex films after γ‐ray treatment

Latex films were prepared by annealing pyrene (Py)‐labeled poly(methyl methacrylate) particles at glass‐transition temperature (100°C). These films were then irradiated by γ‐rays from ⁶⁰Co in a gamma cell at room temperature at the same dose rate (rad/h) for 30 min. Before dissolution films were annealed at elevated temperatures for a 30‐min time interval to complete the film formation process. Steady‐state fluorescence (SSF) technique were used to monitor the dissolution of these irradiated latex films. The dissolution of films in chloroform–heptane (80–20%) mixture was monitored in real time by the Py fluorescence intensity change. Relaxation constants k₀ and desorption coefficients D_d of polymer chains were measured. It was observed that both D_d and k₀ values first increased and then decreased by increasing the annealing temperature. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 129–137, 2002     

Functionalization of crosslinked polyacrylamide through γ‐radiation‐induced grafting of 4‐vinylpyridine

Crosslinked polyacrylamide beads were irradiated in air with a Co⁶⁰ γ‐radiation source. The preirradiated beads were graft‐copolymerized through heating with 4‐vinylpyridine in the presence of benzoyl peroxide. Grafting was studied as a function of various reaction parameters and was determined from the increase in the weight of the original polymer and the estimation of pyridine pendants in the homopolymer‐free graft copolymer. Although making the polymer basic in character, this modification retained the hydrophilic nature of polyacrylamide. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2613–2620, 2002     

Novel anionic polymerization of β-lactones mediated by alkali metal supramolecular complexes

The anionic polymerization of β-lactones mediated by supramolecular complexes of alkali metal alkoxides and naphthalenides is demonstrated. The novel chemistry of the initiation and the propagation steps of polymerization is discussed.     

Direct Decarboxylative Alkynylation of α,α‐Difluoroarylacetic Acids under Transition Metal‐Free Conditions

An efficient and generally applicable protocol for decarboxylative coupling of α,α‐difluoroarylacetic acids with ethynylbenziodoxolone (EBX) reagents has been developed, affording α,α‐difluoromethylated alkynes bearing various functional groups in moderate to excellent yields. Remarkably, this potassium persulfate (K₂S₂O₈)‐promoted reaction employs water as solvent under transition metal‐free conditions, thus providing a green synthetic approach to α,α‐difluoromethylated alkynes.

     

Ruthenium(II)‐Catalyzed Protocol for Preparation of Diverse α,β‐ and β,β‐Dihaloenones from Diazodicarbonyls

Efficient one‐step syntheses of α,β‐ and β,β‐dihaloenones were achieved by ruthenium(II)‐catalyzed reactions between cyclic or acyclic diazodicarbonyl compounds and oxalyl chloride or oxalyl bromide in moderate to good yields. This methodology offers several significant advantages, which include ease of handling, mild reaction conditions, one‐step reaction, and the use of an effective and non‐toxic catalyst. The synthesized compounds were further transformed into highly functionalized novel molecules bearing aromatic rings on the enone moiety using the Suzuki reaction.

     

Cationic copolymers of α,β‐poly‐(N‐2‐hydroxyethyl)‐DL‐aspartamide (PHEA) and α,β‐polyasparthylhydrazide (PAHy): synthesis and characterization

In the present study the derivatization of two water‐soluble synthetic polymers, α,β‐poly(N‐2‐hydroxyethyl)‐DL ‐aspartamide (PHEA) and α,β‐polyasparthylhydrazide (PAHy), with glycidyltrimethylammonium chloride (GTA) is described. This reaction permits the introduction of positive charges in the macromolecular chains of PHEA and PAHy in order to make easier the electrostatic interaction with DNA. Different parameters affect the reaction of derivatization, such as GTA concentration and reaction time. PHEA reacts partially and slowly with GTA; on the contrary the reaction of PAHy with GTA is more rapid and extensive. The derivatization of PHEA and PAHy with GTA is a convenient method to introduce positive groups in their chains and it permits the preparation of interpolyelectrolyte complexes with DNA. © 2000 Society of Chemical Industry     

Concentrated emulsion polymerization for preparation of β‐cyclodextrin‐supported chromatography columns

Concentrated inverse emulsion polymerization was used for making chromatography columns (based on crosslinked polystyrene divinylbenzene (PS‐DVB)) with pore sizes less than 10 μm. According to DSC‐thermal gravimetry thermograms, it was confirmed that the residual monomer concentration after polymerization process is negligible. For application of these columns in chiral chromatography, the β‐cyclodextrin is chemically fixed on the PS‐DVB resin pore surface. The presence of hydroxyl groups in the PS‐DVB resin after chemical modification was confirmed by FTIR spectroscopy. By chemical modification of the PS‐DVB resin, thermal stability increased up to 446°C. The structure of columns was analyzed by scanning electron microscopy (SEM). SEM evaluations showed that the porous structure of PS‐DVB resin was maintained intact after the chemical modification with β‐cyclodextrin. According to X‐ray data, presence of the crystalline domain that is related to β‐cyclodextrin is confirmed.© 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 857–863, 2006     

Effects of reaction conditions on laccase‐catalyzed α‐naphthol polymerization

Enzymatic oxidative polymerization of α‐naphthol was carried out batch‐wise with the laccase enzyme, produced by Trametes versicolor (ATCC 200801). The polymerization reaction was conducted in a closed, temperature controlled system containing acetone (solvent) and sodium acetate buffer for pH control. The effects of the organic solvent (acetone) composition, monomer (α‐naphthol) and enzyme concentrations, buffer pH and temperature on the polymerization rate were investigated with respect to initial reaction conditions and depletion rate of dissolved oxygen. The optimum acetone composition, pH, monomer, dissolved oxygen and enzyme concentrations were determined as 50% (v/v), 5, 3409 gm⁻³, 20.3 gm⁻³ and 0.173 U cm⁻³, respectively; these values provided the most desirable conditions for initial reaction rate. Temperature rise supported the rate increase up to 37 °C, after which the rate tended to be stable due to a drop in dissolved oxygen concentration. The product polymer, poly(α‐naphthol), with an average molecular weight of 4920 Da was soluble in common organic solvents. © 2000 Society of Chemical Industry     

Highly Enantioselective Phase‐Transfer Catalytic α‐Alkylation of α‐tert‐Butoxycarbonyllactams: Construction of β‐Quaternary Chiral Pyrrolidine and Piperidine Systems

A new enantioselective α‐alkylation of α‐tert‐butoxycarbonyllactams for the construction of β‐quaternary chiral pyrrolidine and piperidine core systems is reported. α‐Alkylations of N‐methyl‐α‐tert‐butoxycarbonylbutyrolactam and N‐diphenylmethyl‐α‐tert‐butoxycarbonylvalerolactam under phase‐transfer catalytic conditions (solid potassium hydroxide, toluene, −40 °C) in the presence of (S,S)‐3,4,5‐trifluorophenyl‐3,3′,5,5′‐tetrahydro‐2,6‐bis(3,4,5‐trifluorophenyl)‐4,4′‐spirobi[4H‐dinaphth[2,1‐c:1′,2′‐e]azepinium] bromide [(S,S)‐NAS Br] (5 mol%) afforded the corresponding α‐alkyl‐α‐tert‐butoxycarbonyllactams in very high chemical (up to 99%) and optical yields (up to 98% ee). Our new catalytic systems provide attractive synthetic methods for pyrrolidine‐ and piperidine‐based alkaloids and chiral intermediates with β‐quaternary carbon centers.     

Highly Enantioselective Michael Addition of Cyclic 1,3‐Dicarbonyl Compounds to β,γ‐Unsaturated α‐Keto Esters

A highly enantioselective Michael addition of cyclic 1,3‐dicarbonyl compounds to β,γ‐unsaturated α‐keto esters catalyzed by amino acid‐derived thiourea‐tertiary‐amine catalysts is presented. Using 5 mol% of a novel tyrosine‐derived thiourea catalyst, a series of chiral coumarin derivatives were obtained in excellent yields (up to 99%) and with up to 96% ee under very mild conditions within a short reaction time.