Breakdown characteristics of gas‐insulated switchgear for nonstandard lightning impulse waveforms under nonuniform electric field

To improve the insulation specification of gas‐insulated switchgear (GIS), it is necessary to recognize the insulation characteristics of SF₆ gas during actual surges (called nonstandard lightning impulse waveforms) occurring at field substations. The authors observed the insulation characteristics of SF₆ gas gap under various types of nonstandard lightning impulse waveforms and compared them quantitatively with those obtained with standard lightning impulse waveforms. The experimental results were used to derive an evaluation method for real surges, which was applied to typical surges for various UHV and 500‐kV systems. In the preceding study, therefore, only the case of a quasi‐uniform electric field (with a typical range of field utilization factors in the bus of a GIS) was investigated. In the present investigation, the insulation characteristics of an SF₆ gas gap for a nonuniform electric field were observed experimentally and an evaluation method for converting nonstandard lightning impulse waveforms equivalently to the standard lightning impulse waveform was investigated. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 177(1): 11–18, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21144     

Dielectric characteristics of oil‐filled transformer in the presence of nonstandard lightning surge waveforms

To achieve a rational insulation design for transformers, it is important to evaluate dielectric strength against surges actually impinging on equipment on‐site. This paper deals with the breakdown voltage characteristics of an oil gap under nonstandard lightning surge waveforms combined with oscillatory voltages. It is found that the breakdown voltages of the oil gap under nonstandard impulse waveforms are higher than standard lightning impulse voltages. The results can be ascribed to V–t characteristics of the oil gap in short‐time impulse voltage ranges. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 146(3): 39–45, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10229     

Insulation characteristics of CO2 gas for nonstandard lightning impulse oscillations: Evaluation method of nonstandard lightning impulse waveform for CO2 gas insulation

SF₆ gas is widely used in electric power apparatus such as gas‐insulated switchgears (GIS), because of its superior dielectric properties; however, it has been identified as a greenhouse gas at COP3 in 1997, and alternative insulation gases to SF₆ have recently been investigated. One of the candidates is CO₂ gas, which has lower global warming potential (GWP). However, CO₂ gas has a lower withstand voltage level than SF₆ gas; therefore, it is necessary to rationalize the equipment insulation level and reexamine the insulating test voltage for electric power apparatus as low as possible. From our previous investigation, in SF₆ gas insulation system, we obtained that the insulation requirements of the real surges (called nonstandard lightning impulse waveform) are not as severe as those of the standard lightning impulse waveform. This paper describes the evaluation method for real surges, based on insulation characteristics of CO₂ gas gaps. Furthermore, the method was applied to typical field overvoltage waveform in the lightning surge time region for 500‐kV systems and it is obtained that the equivalent peak value of the standard lightning impulse waveform is possibly reduced by 10 to 15%. © 2008 Wiley Periodicals, Inc. Electr Eng Jpn, 163(3): 1– 9, 2008; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20560     

Evaluation of Breakdown Characteristics of Gas Insulated Switchgears for Non-Standard Lightning Impulse Waveforms - Breakdown Characteristics for Non-Standard Lightning Impulse Waveforms Associated with Lightning Surges

To lower the insulation specifications (specifically, the lightning impulse withstand voltage) of a gas insulated switchgear (GIS) and thus cut the equipment cost while maintaining the high reliability of its insulation performance, it is necessary to define in an organized way the insulation characteristics for non-standard lightning impulse voltage waveforms that represent actual surge waveforms in the field and compare them with the characteristics for the standard lightning impulse waveform quantitatively. In the preceding paper, lightning surge waveforms and disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations were analyzed and five to six non-standard lightning surge waveforms with basic frequencies of 0.6 to 5.0 MHz were identified. In this paper, the dielectric breakdown voltage - time characteristics were measured under several different conditions mainly for the quasi-uniform SF₆ gas gaps that represent an insulation element of a GIS toward four kinds of non-standard lightning impulse waveforms associated with lightning surges. As a result, in the tested range, the dielectric breakdown values for nonstandard lightning impulse waveforms were higher than for the standard lightning impulse waveform by 3% to 32%.     

V-t characteristics of SF6 gas during lightning surges

The waveform of a standard lightning impulse differs greatly from those of actual lightning surges acting on GIS. This raises the problem of the equivalence of the standard lightning impulse. This report describes the effect of voltage waveforms on insulating performance in an SF₆ gas gap subjected to fast oscillating impulse voltages simulating actual lightning surges, and the evaluation of V-t characteristics by applying the equal area criterion. © 1997 Scripta Technica, Inc. Electr Eng Jpn, 119(4): 1–11, 1997     

Insulation characteristics and its evaluation method of N2 gas for nonstandard lightning impulse waveforms

Until recently, SF₆ gas has widely been used as the best insulating medium in substation equipment. However, SF₆ gas was specified to be a greenhouse gas at COP3 in 1997 because of its high global warming potential (GWP), and alternative insulation gases to SF₆ have been sought for a long time. Alternatives using the natural gases are considered to be suitable, but none of them show better properties for insulation as well as good environmental compatibility. Therefore, it is necessary to rationalize the equipment insulation level and reduce the test voltage of electric power apparatus to as low a level as possible. The actual lightning surge waveform (so‐called nonstandard lightning impulse waveform) occurring in the actual field is different from the standard lightning impulse waveform (1.2/50 μs). There are many cases in which the actual lightning surge waveform has a steep rise and large decay of overvoltage, and the insulation requirements are not as severe as those for the standard lightning impulse waveform. In this paper, we focused our research on N₂ gas as an SF₆ substitute and investigated the insulation characteristics of N₂ gas for a single‐frequency oscillatory waveform with various frequencies from 2.7 to 20.0 MHz and damping ratios. Based on the experimental results, it might be possible to reduce the test voltage of N₂ gas insulation by evaluating the crest value of the actual lightning surge waveform that has been converted into an equivalent standard lightning impulse waveform. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 167(2): 10–20, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20754     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Results of lightning impulse tests for a 275‐kV full GIS substation

This paper describes the outline and results of the lightning impulse tests for a 275‐kV full GIS substation. The behavior of lightning surges is a very important factor for the rational design of substations and low‐voltage and control circuits inside the substations. For the above reason, we carried out lightning impulse tests for a new 275‐kV full GIS substation. In these tests, we measured voltage induced in low‐voltage and control circuits, transient characteristics of grounding grid, injected voltage and current waveforms, and so on. By investigating these data, we confirmed the behavior of lightning surges inside the substation. We also compared simulated waveforms by EMTP analysis with the measured waveforms. The simulated results agreed well with the measured results. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 146(1): 46–58, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10230     

Evaluation of breakdown characteristics of gas insulated switchgears for non-standard lightning impulse waveforms - method for converting non-standard lightning impulse waveforms into standard lightning impulse waveforms -

To lower the lightning impulse withstand voltage of gas insulated switchgear (GIS) while maintaining the high reliability of its insulation performance, it is important to define in an organized way the insulation characteristics for non-standard lightning impulse voltage waveforms that represent actual surge waveforms in the field and compare them with the characteristics for the standard lightning impulse waveform quantitatively. In the preceding researches, lightning surge waveforms and disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations were analyzed and five to six kinds of non-standard lightning impulse waveforms with basic frequencies of 0.6 to 5.0 MHz were identified. Then, the dielectric breakdown voltage ? time characteristics were measured under several different conditions on the quasi-uniform SF6 gas gaps and partly the coneshaped insulating spacers that represent insulation elements of GIS for six kinds of nonstandard lightning impulse waveforms. In this paper, the resultant breakdown voltages were evaluated in terms of the overvoltage duration, which led to their formulation in a unified way. On the basis of these insulation characteristics and their unified formulation, the paper investigated a method for converting non-standard lightning impulse waveforms into standard lightning impulse waveforms with equivalent stress for the insulation. When the constructed algorithm was applied to five examples of representative two type waveforms in the lightning surge time region, they were converted into standard lightning impulse waveforms with crest values reduced by 20% to 34%, suggesting potentiality for reduction of lightning impulse insulation specifications of GIS.     

Insulation characteristics of SF6 gas for nonstandard impulse voltage polarity reversal pulse waveforms

Evaluation of insulation strength for lightning surge that actually enters into substations is important in estimating insulation reliability of gas‐insulated equipment. The standard lightning impulse voltage (1.2/50 µs) is used for factory tests. However, the actual lightning surge waveforms in substations are complex and are usually superimposed with various oscillations. Insulation characteristics of SF₆ gas as a function of such complex voltages have not been sufficiently clarified. This paper deals with gap breakdown characteristics in SF₆ gas under submicrosecond pulses. Breakdown voltages are lower under a polarity reversal condition than under a monopolarity condition. The cause of this difference is discussed while observing discharge propagation using an image converter camera. The electrode size effect is also discussed. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 146(4): 18–25, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10246     

Development of 72‐kV high‐pressure air‐insulated GIS with vacuum circuit breaker

SF₆ gas has excellent dielectric strength and interruption performance. For these reasons, it has been widely used for gas‐insulated switchgear (GIS). However, use of SF₆ gas has become regulated under agreements set at the 1997 COP3. Thus, investigation and development for GIS with a lower amount of SF₆ gas are being carried out worldwide. Presently, SF₆‐free GIS has been commercialized for the 24‐kV class. Air or N₂ gas is used as the insulation gas for this GIS. On the other hand, SF₆‐free GIS has not been commercialized for the 72‐kV‐class GIS. The dielectric strengths of air and N₂ gas are approximately one‐third that of SF₆ gas. To enhance the insulation performance of air and N₂ we have investigated a hybrid gas insulation system which has the combined features of providing an insulation coating and suitable insulation gas. We have developed the world's first 72‐kV SF₆‐free GIS. This paper deals with key technologies for SF₆‐free GIS, such as the hybrid insulation structure, a bellows for the high‐pressure vacuum circuit breaker, a newly designed disconnector and spacer, and prevention of particle levitation. Test results of the 72‐kV high‐pressure air‐insulated GIS with the vacuum circuit breaker are described. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 13–23, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20451     

Steep Impulse Voltage Characteristics of Suspension Insulators

Transmission and distribution lines are sometimes struck by lightning and there is some risk of electrical puncture of suspension insulators due to high and steep lightning surge voltage. When the insulators suffer from steep lightning surge voltages, the solid insulating body of the insulators sometimes is punctured before external flashover in the air occurs. These characteristics were investigated on the insulators in the laboratory by using different steep impulse voltages. From the investigation results, both V-t characteristics of external flashover and internal puncture were obtained on the insulators. It was found that the puncture of the insulators is a matter of probability, depending on the dimensions of the insulators, steep impulse voltages and number of impulse voltage applications. Especially, the effect of number of voltage applications on puncture probability was clarified and partial damage by a small number of voltage applications was verified before complete puncture occurred. Based on the study results, an empirical equation relating to probability of puncture (P), impulse voltage (V) and number of voltage applications (N) was established.     

Problems of the application of N2/SF6 mixtures to gas‐insulated bus

In designing a gas‐insulated bus (GIB) using N₂/SF₆ mixtures, there are many application problems, such as the mixture pressure needed in order to maintain the required dielectric and heat transfer performance. Problems of recycling SF₆ are also essential in applying N₂/SF₆ mixtures. This paper presents the minimum breakdown field strength at lightning impulse and the temperature rise of the conductor and enclosure as measured for N₂/SF₆ mixtures. Considering the dielectric and heat transfer properties, we clarify the problems of application of mixtures to a GIB and discuss the appropriate mixture ratio of SF₆ in designing a GIB comparable to the present dimensions. In addition, the lowest limit of SF₆ content in a liquefied recovering method is theoretically estimated for reference in practical SF₆ recovery from mixtures. It is important for design to consider both breakdown phenomena, including the area effect of electrode, and the heat transfer properties of mixtures. © 2001 Scripta Technica, Electr Eng Jpn, 137(4): 25–31, 2001     

Application of step‐response test for evaluation of uncertainty of standard measuring system for lightning‐impulse high voltage

In evaluating the uncertainty of the standard measuring system for lightning‐impulse high voltages, which is composed of a standard voltage divider, a digital recorder, and calibrators, step‐response tests of the standard voltage divider may be useful. In this paper, a convolution algorithm is employed to calculate the output impulse voltage waveforms from measured step‐response waveforms. The uncertainties of peak‐value measurement due to the influence of the nominal epoch, uncertainty of the peak‐value measurement due to dispersion of the AC scale factor, and uncertainty of the virtual front‐time measurement due to long‐term stability are evaluated. Furthermore, the error of the virtual front time of the output waveforms is discussed. The front part of the step‐response waveform, t≤ T₃₀%, does not influence the error of the virtual front time. Therefore, for the standard voltage divider, the step‐response parameters, that is, the experimental response time, partial response time, settling time, and overshoot, have almost nothing to do with the error of the virtual front time. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 180(2): 24–32, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21279     

Partial discharge endurance life of polymer insulating materials at high temperature

This paper describes the partial discharge (PD) characteristics and V‐t characteristics of several insulating materials, such as liquid crystal polymer, epoxy resins, polyimide, and polyethylene‐terephthalate (PET) with a needle‐plane electrode system at elevated temperature. The life index n for an applied electric field less than 20 kV/mm is found to be about 9 and that for more than 20 kV/mm is found to be less than 4. The PD characteristics of the insulating materials varied. These V‐t characteristics due to PD degradation were similar to those at room temperature except for the absolute life time. © 1998 Scripta Technica, Electr Eng Jpn, 126(1): 15–22, 1999     

Insulation technology in dry air and vacuum for a 72‐kV low‐pressure dry‐air insulated switchgear

A new 72‐kV rated low‐pressure dry‐air insulated switchgear applying electromagnetic actuation and a function that supports CBM has been developed. First, the dielectric characteristics in dry air under lightning impulse application were investigated for bare and insulator‐covered electrodes. The dependence of the breakdown electric field strength on the effective area was found in order to apply it to the configuration design of the insulation mold for the vacuum interrupter. In addition, the dependence of the moisture volume on the surface resistance was found in order to decide the moisture volume in the gas pressure tank. Next, a new vacuum circuit breaker (VCB) was designed. To keep the dimensions the same as in the previous 72‐kV SF₆ gas insulated switchgear, the distance between contacts in the vacuum interrupter must be shorter than in the previous switchgear. The voltage withstand capability between electrodes practically designed for the vacuum interrupter was investigated under DC voltage application, in a small capacitive current breaking simulation. The gap configuration, including contacts and slits, was optimized and the distance was shortened by 11% from the previous switchgear. As a result, the new low‐pressure dry‐air insulated switchgear was designed to be comparable in external size to the previous SF₆ gas insulated switchgear. Using dry air as an insulation medium with low pressure makes it possible to reduce the environmental burden. © 2011 Wiley Periodicals, Inc. Electr Eng Jpn, 175(1): 18–24, 2011; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21058     

Relative permittivity and conductivity of water‐treed region in XLPE estimated by an equivalent circuit

By dividing a water‐treed XLPE sheet sample of 1 mm thickness into a nondegraded region and a water‐treed one, relative permittivity and AC conductivity σ_AC2 of the water‐treed region have been estimated using an equivalent circuit. The variation of and σ_AC2 with the length r of the water‐treed region has been discussed based on the Sillars model. It was concluded that the volume fraction of water in the water‐treed layer is in the range from 0.5% to 1.5% for the most‐degraded XLPE sheet, which depends on the ratio of axes of spheroids to which water‐filled voids and channels are compared. It was also concluded that the AC conductivity of water in the water‐treed region ranges from 3 × 10^?3 S/m to 2 × 10^?2 S/m. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 148(3): 7–14, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10332     

Evaluation of breakdown characteristics of gas insulated switchgears for non-standard lightning impulse waveforms - analysis and generation circuit of non-standard lightning impulse waveforms in actual field

To lower the insulation specifications (specifically, the lightning impulse withstand voltage) of a gas insulated switchgear (GIS) and thus cut the equipment cost while maintaining the high reliability of its insulation performance, it is necessary to define in an organized way the insulation characteristics for non-standard lightning impulse voltage waveforms that represent actual surge waveforms in the field and compare them with the characteristics for the standard lightning impulse waveform quantitatively. In this paper, first, lightning surge waveforms and disconnector switching surge waveforms at UHV, 500 kV, and 275 kV substations were analyzed and five non-standard lightning surge waveforms with basic frequencies of 0.6 to 5.0 MHz were identified. Next, high-voltage circuits that generate these non-standard lightning surge waveforms were designed and constituted using EMTP (electro magnetic transients program) based on a circuit with a gap, inductors, and resistors connected in series and resistors and capacitors connected in parallel. Further, circuits were actually constructed, to obtain voltage waveforms approximately equal to those designed. Finally, the dielectric breakdown voltage-time characteristics were measured under several different conditions for the quasi-uniform SF₆ gas gap that represents an insulation element of a GIS. As a result, it was found that, in the tested range, the dielectric breakdown values for non-standard lightning impulse waveforms were higher than for the standard lightning impulse waveform by 6% to 32%     

Observation space for lowest PDOP in absolute‐range‐based 2‐D wireless location systems

A closed‐form expression for the position dilution of precision (PDOP) in absolute‐range‐based two‐dimensional (2‐D) wireless location systems is derived. Then, using the closed‐form expression, the observation space (OS) required for achieving the lowest PDOP of $2/\sqrt{N}$ is studied, where N is the number of measuring points. The OS is measured by central angle of a sector which covers all measuring points. The target is located at the vertex of the sector. It is shown that, for achieving the lowest PDOP of $2/\sqrt{N}$, the OS is required to be larger than or equal to π/2 while N is even. When N = 3, the OS is instead required to be larger than or equal to 2π/3. It is also shown that the OS of 2π/3 is sufficient to achieve the lowest PDOP of $2/\sqrt{N}$ while N is odd. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Dielectric characteristics of turn-to-turn insulation models of gas-insulated transformer under very fast transient voltages

This paper deals with the partial discharge inception voltage (PDIV) and breakdown voltage (BDV) characteristics of turn-to-turn insulation models for SF₆ gas-insulated transformers in the presence of steep-front short-pulse voltages, whose waveforms are 35/65 ns and 50/370 ns. It was determined that PDIV at nanosecond pulses were 1.05 to 1.15 times higher than those at standard impulse voltages and that the BDV at nanosecond pulses were about 1.4 times higher than those at standard impulse voltages. The ratio of impulse PDIV to ac PDIV is 1.40 to 1.48 for standard impulse voltages and 1.32 to 1.37 for switching impulses. © 1998 Scripta Technica, Inc. Electr Eng Jpn, 121(3): 36–43, 1997