Effect of annealing on poly(urethane‐siloxane) copolymers

Poly(urethane‐siloxane) copolymers were prepared by copolymerization of OH‐terminated polydimethylsiloxane (PDMS), which was utilized as the soft segment, as well as 4,4′‐diphenylmethane diisocyanate (MDI) and 1,4‐butanediol (1,4‐BD), which were both hard segments. These copolymers exhibited almost complete phase separation between soft and hard segments, giving rise to a very simple material structure in this investigation. The thermal behavior of the amorphous hard segment of the copolymer with 62.3% hard‐segment content was examined by differential scanning calorimetry (DSC). Both the T₁ temperature and the magnitude of the T₁ endotherm increased linearly with the logarithmic annealing time at an annealing temperature of 100°C. The typical enthalpy of relaxation was attributed to the physical aging of the amorphous hard segment. The T₁ endotherm shifted to high temperature until it merged with the T₂ endotherm as the annealing temperature increased. Following annealing at 170°C for various periods, the DSC curves presented two endothermic regions. The first endotherm assigned as T₂ was the result of the enthalpy relaxation of the hard segment. The second endothermic peak (T₃) was caused by the hard‐segment crystal. The exothermic curves at an annealing temperature of above 150°C exhibited an exotherm caused by the T₃ microcrystalline growth. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5174–5183, 2006     

Electrochemical preparation of poly(2‐bromoaniline) and poly(aniline‐co‐2‐bromoaniline) in acetonitrile

Electrochemical preparation of poly(2‐bromoaniline) (PBrANI) and poly(aniline‐co‐2‐bromoaniline) [P(An‐co‐2‐BrAn)] was carried out in an acetonitrile solution containing tetrabutylammonium perchlorate (TBAP) and perchloric acid (HClO₄). The cyclic voltammograms during the copolymerization had many features similar to those for the usual polymerization of aniline. The copolymer exhibits a higher dry electrical conductivity value than that of PBrANI and a lower one than that of PANI. The observed decrease in the conductivity of the copolymer relative to PANI is attributed to the incorporation of bromine moieties into the polyaniline chain. The structure and properties of the polymer and copolymer were elucidated using cyclic voltammetry (CV), FTIR, and UV‐vis spectroscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2460–2468, 2003     

All‐polymer electromechanical systems consisting of electrostrictive poly(vinylidene fluoride‐trifluoroethylene) and conductive polyaniline

The low elastic modulus and the ability to withstand high strain without failure make the conducting polymer attractive for a wide range of acoustic applications based on high‐strain electroactive polymers. In this article, we examine the electric and electromechanical performance of all‐polymer electromechanical systems, fabricated by painting conductive polyaniline (PANI) doped with camphor sulfonic acid (HCSA) on both sides of electrostrictive Poly(vinylidene fluoride‐trifluoroethylene) (P(VDF‐TrFE)) copolymer films, and compare them with those from the same copolymers with gold electrodes. The all‐polymer composite films are flexible, with strong coherent interfaces between the electrostrictive polymer layer and the conductive polymer layer. The electric performance such as dielectric properties and polarization hysteresis loops from P(VDF‐TrFE)/PANI film is nearly identical to those of P(VDF‐TrFE)/gold films in a wide temperature (from −50 to 120°C), and frequency range (from 1 Hz to 1 MHz). The all‐polymer systems also show a similar or even larger electric field induced strain response than that of films with electrodes under identical measurement conditions. The results demonstrate that the polyaniline/HCSA is good candidate material as the electrodes for electroactive polymers. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 945–951, 2000     

The effect of chemical heterogeneity on the properties of statistical copolymers: the conductivity of poly(aniline‐co‐2‐bromoaniline)

Chemical heterogeneity can influence the properties of statistical copolymers. It is shown that any integral property of a copolymer will depend on the chemical heterogeneity if such a property is a non‐linear function of copolymer composition. This is illustrated by means of the conductivity of copolymers of aniline and 2‐bromoaniline. The monomer reactivity ratios of this monomer pair are r_A (aniline) = 0.94 and r_B (2‐bromoaniline) = 0.31. The dependence of conductivity on the copolymer composition is non‐linear. Consequently, the conductivity depends on the compositional distribution, ie on the extent of chemical heterogeneity. Heterogeneous high‐conversion copolymers have lower conductivity than corresponding relatively homogeneous low‐conversion copolymers. The change in the average copolymer composition with increasing conversion is demonstrated for a copolymerization mixture containing 30 mol% aniline. The conductivity decreases at the same time as the chemical heterogeneity of the copolymer develops. The change in the average copolymer composition alone cannot explain the observed conductivity decrease. The conductivity is dependent not only on average composition but also on the chemical composition distribution. Copyright © 2004 Society of Chemical Industry     

Characteristics of dual‐type electrochromic devices based on poly(ethylene oxide) copolymers

Dual‐type polymer electrochromic devices based on [(3‐thienyl)methylmethacrylate]‐co‐[p‐vinyl benzyloxy poly(ethylene oxide)]/polythiophene and thiophene‐capped poly(ethylene oxide)/polythiophene and ethylene dioxythiophene were constructed via electropolymerization. Spectroelectrochemistry, switching ability and stability of the devices were investigated using UV‐visible spectrophotometry and cyclic voltammetry. These devices exhibit low switching voltages and short switching times with reasonable switching stability under atmospheric conditions. Copyright © 2006 Society of Chemical Industry     

Characterization of poly(indole‐5‐carboxylic acid) in aqueous rechargeable cells

Self-doped poly(indole-5-carboxylic acid) (P5CO₂H) is electrodeposited from acetonitrile containing 0.1M LiClO₄ as electrolyte and characterized by UV–vis, IR, cyclic voltammetry, and scanning electron microscopy techniques. The polymer is evaluated as a cathode active material together with a Zn anode in rechargeable cells containing 1M ZnSO₄ at pH 5. The cell shows an open circuit voltage of 1.36 V and a specific capacity of 67 Ah kg⁻¹. The ac impedance study shows a predominant diffusion mechanism. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 917–922, 2005     

Mechanochemical synthesis and characterization of poly(2,5‐dimethoxy aniline) salts

The interfacial interaction and orientation of molecules during the polymerization process plays a vital role in the enhancement of the surface properties of conducting polymers. In this perspective, a solid‐phase mechanochemical route is employed to prepare poly(2,5‐dimethoxy aniline) (PDMA) and its salts with superior properties. Various studies performed on the as‐prepared polymer highlights the formation of polymeric particles with excellent physicochemical properties. Elemental analysis showed the presence of dopants anion in the polymeric backbone. Spectroscopic profile of PDMAs revealed the formation of emeraldine form of PDMAs. Moreover, these studies indicate the formation of PDMA‐HCl in a highly doped state. The surface morphological pictures of PDMAs revealed the formation of aggregated microstructured to nanostructured particulates. X‐ray diffraction, cyclic voltammetry were used to evaluate the physicochemical properties of PDMAs. PDMA salts exhibited crystalline behavior and good electrochemical activity. TG/DTA analysis showed that all the PDMAs were thermally stable up to 240°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The synthesis of poly(3‐hydroxybutyrate)‐g‐poly(methylmethacrylate) brush type graft copolymers by atom transfer radical polymerization method

Brush type of poly (3‐hydroxy butyrate), PHB, copolymer synthesis has been reported. Natural PHB was chlorinated by passing chlorine gas through PHB solution in CHCl₃/CCl₄ mixture (75/25 v/v) to prepare chlorinated PHB, PHB‐Cl, with the chlorine contents varying between 2.18 and 39.8 wt %. Toluene solution of PHB‐Cl was used in the atom transfer radical polymerization (ATRP) of methyl methacrylate, MMA, in the presence of cuprous bromide (CuBr)/2,2′‐bipyridine complex as catalyst, at 90°C. This “grafting from” technique led to obtain poly (3‐hydroxybutyrate)‐g‐poly(methylmethacrylate) (PHB‐g‐PMMA) brush type graft copolymers (cylindrical brush). The polymer brushes were fractionated by fractional precipitation methods and the γ values calculated from the ratio of the volume of nonsolvent to volume of solvent of brushes were ranged between 2.8 and 9.5 depending on the molecular weight, grafting density, and side chain length of the brushes, while the γ values of PHB, PHB‐Cl, and homo‐PMMA were 2.7–3.8, 0.3–2.4, and 3.0–3.9, respectively. The fractionated brushes were characterized by gel permeation chromatography, ¹H‐NMR spectrometry, thermogravimetric analysis (TGA), and differential scanning calorimetry techniques. PHB‐g‐PMMA brush type graft copolymers showed narrower molecular weight distribution (mostly in range between 1.3 and 2.2) than the PHB‐Cl macroinitiator (1.6–3.5). PHB contents in the brushes were calculated from their TGA thermograms and found to be in range between 22 and 42 mol %. The morphologies of PHB‐g‐PMMA brushes were also studied by scanning electron microscopy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

ABTS•+ scavenging activity of polypyrrole,polyaniline and poly(3,4‐ethylenedioxythiophene)

Although many methods are available for the evaluation of the antioxidant capacity of samples presented in the liquid state, typically food and beverages, to date only the 2,2′‐diphenyl‐1‐picrylhydrazyl (DPPH) assay has been applied to the measurement of the antioxidant capacity of solid samples such as active packaging materials. A modified 2,2′‐azino‐bis(3‐ethylbenzothiazoline‐6‐sulfonic acid) diammonium salt (ABTS) assay has been successfully developed for the measurement of the antioxidant capacity of conducting polymer powders. The ABTS^?+ radical scavenging activity of polypyrrole (PPy), polyaniline (PANI) and poly(3,4‐ethylenedioxythiophene) (PEDOT) powders was compared. The ranking order for greatest antioxidant capacity among the conducing polymer powders was PANI > PPy > PEDOT. The reduced forms of all the three conducting polymer samples were found to show greater radical scavenging activity than their as‐prepared partially oxidized forms. The modified ABTS assay is a simple, rapid and sensitive method for evaluating the antioxidant capacity of conducting polymer powders. The method is also suitable for composite antioxidant materials comprising a conducting polymer and a conventional packaging polymer. Copyright © 2010 Society of Chemical Industry     

Polymer blends of poly(trimethylene terephthalate) and polystyrene compatibilized by styrene‐glycidyl methacrylate copolymers

The compatibilizing effects of styrene‐glycidyl methacrylate (SG) copolymers with various glycidyl methyacrylate (GMA) contents on immiscible blends of poly(trimethylene terephthalate) (PTT) and polystyrene (PS) were investigated using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), and ¹³C‐solid‐state nuclear magnetic resonance (NMR) spectroscopy. The epoxy functional groups in the SG copolymer were able to react with the PTT end groups (? COOH or ? OH) to form SG‐g‐PTT copolymers during melt processing. These in situ–formed graft copolymers tended to reside along the interface to reduce the interfacial tension and to increase the interfacial adhesion. The compatibilized PTT/PS blend possessed a smaller phase domain, higher viscosity, and better tensile properties than did the corresponding uncompatibilized blend. For all compositions, about 5% GMA in SG copolymer was found to be the optimum content to produce the best compatibilization of the blend. This study demonstrated that SG copolymers can be used efficiently in compatibilizing polymer blends of PTT and PS. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2247–2252, 2003     

Highly conductive new aniline copolymers: poly(aniline‐co‐aminoacetophenone)s

Copolymers of aniline and o‐/m‐aminoacetophenone of different compositions were synthesized by oxidative chemical copolymerization. Two different methods were employed, emulsion and inverse emulsion, with different oxidants, ammonium persulphate and benzoyl peroxide, to study the effect of synthesis conditions on the yield, solubility and conductivity of the copolymers. The copolymer compositions were determined using proton NMR spectroscopy. The reactivity ratios determined by the Finemann–Ross method indicate lower reactivity for m‐aminoacetophenone relative to aniline in the emulsion method, while the reverse holds true in the inverse emulsion method. Copolymers formed by the former pathway are random type as determined by the Finemann–Ross method. The copolymers have crystalline/amorphous morphologies and good conductivity. They exhibit enhanced solubility compared with polyaniline. Copyright © 2005 Society of Chemical Industry     

Synthesis and surface properties of polystyrene‐graft‐poly(ethylene glycol) copolymers

Polystyrene‐graft‐poly(ethylene glycol) copolymers (PS‐g‐PEG) were successfully synthesized using the “grafting‐through” method. The graft copolymers and the surface properties of their coats were characterized by 1 H‐NMR, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), X‐ray photoelectron spectroscopy (XPS), static contact angle measurement, and atomic force microscopy (AFM). Both DSC and TEM indicated that the graft copolymers had a microphase separated structure. AFM showed the microphase separated structure also occurred at the coat surface, especially at high PEG content, which could also be indirectly confirmed by the XPS and contact angle results. The formation mechanism of the microphase separated structure was discussed. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1458–1465, 2007     

Preparation of heat‐resistant branched poly(styrene‐alt‐NPMI) by ATRP with divinylbenzene as the branching agent

Heat‐resistant branched poly(styrene‐alt‐NPMI) has been prepared via atom transfer radical polymerization (ATRP) of styrene (St) and N‐phenyl maleimide (NPMI) with divinylbenzene (DVB) as the branching agent in anisole at 80°C. Gas chromatography (GC) was used to determine the conversion of the reactants. Triple detection gel permeation chromatography (TD‐GPC) was used to analyze the copolymers. The results show that the polymerization yields primary chains predominately in the early stages and the formation of branched molecules occurs mainly when conversion is higher than 50%. As expected, higher dosage of DVB in our investigation range favors the formation of polymers with higher degree of branching. All the resulting branched poly(styrene‐alt‐NPMI)s have glass transition temperature (T_g) above 175°C, extrapolated initial weight loss temperature (T_i) above 410°C and statistic heat‐resistant index above 200°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of polyaniline coated polystyrene‐poly(styrene‐co‐sodium 4‐styrenesulfonate) microparticles and the further fabrication of hollow polyaniline microspheres

In this article, the microparticles of polystyrene‐poly(styrene‐co‐sodium 4‐styrenesulfonate) (PS‐PSS) coated by polyaniline (PANI) were prepared and hollow PANI microspheres were further obtained by dissolving the core. First, surface‐sulfonated monodispersed PS was prepared by copolymerization of sodium 4‐styrenesulfonate (SSS) and styrene with dispersion polymerization method. Then aniline was polymerized on the surface of the surface‐sulfonated PS (PS‐PSS) by chemical oxidative polymerization. After purification, we prepared core‐shell (PS‐PSS)/PANI particles. Hollow PANI microspheres were prepared by dissolving the plastic PS core of the (PS‐PSS)/PANI particles in chloroform. The growth process of PANI on the surface of PS‐PSS particles was investigated and the hollow PANI microspheres were characterized. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Lower critical solution temperatures of thermo‐responsive poly(N‐isopropylacrylamide) copolymers with racemate or single enantiomer groups

BACKGROUND: Thermo‐responsive copolymers with racemate or single enantiomer groups are attracting increasing attention due to their fascinating functional properties and potential applications. However, there is a lack of systematic information about the lower critical solution temperature (LCST) of poly(N‐isopropylacrylamide)‐based thermo‐responsive chiral recognition systems. In this study, a series of thermo‐responsive chiral recognition copolymers, poly[(N‐isopropylacrylamide)‐co‐(N‐(S)‐sec‐butylacrylamide)] (PN‐S‐B) and poly[(N‐isopropylacrylamide)‐co‐(N‐(R,S)‐sec‐butylacrylamide)] (PN‐R,S‐B), with different molar compositions, were prepared. The effects of heating and cooling processes, optical activity and amount of chiral recognition groups in the copolymers on the LCSTs of the prepared copolymers were systematically studied. RESULTS: LCST hysteresis phenomena are found in the phase transition processes of PN‐S‐B and PN‐R,S‐B copolymers in a heating and cooling cycle. The LCSTs of PN‐S‐B and PN‐R,S‐B during the heating process are higher than those during the cooling process. With similar molar ratios of N‐isopropylacrylamide groups in the copolymers, the LCST of the copolymer containing a single enantiomer (PN‐S‐B) is lower than that of the copolymer containing racemate (PN‐R,S‐B) due to the steric structural difference. The LCSTs of PN‐R,S‐B copolymers are in inverse proportion to the molar contents of the hydrophobic R,S‐B moieties in these copolymers. CONCLUSION: The results provide valuable guidance for designing and fabricating thermo‐responsive chiral recognition systems with desired LCSTs. Copyright © 2008 Society of Chemical Industry     

RAFT synthesis of poly(N‐isopropylacrylamide) and poly(methacrylic acid) homopolymers and block copolymers: Kinetics and characterization

Reversible addition‐fragmentation chain transfer (RAFT) polymerization was used successfully to synthesize temperature‐responsive poly(N‐isopropylacrylamide) (PNIPAAm), poly(methacrylic acid) (PMAA), and their temperature‐responsive block copolymers. Detailed RAFT polymerization kinetics of the homopolymers was studied. PNIPAAm and PMAA homopolymerization showed living characteristics that include a linear relationship between M _n and conversion, controlled molecular weights, and relatively narrow molecular weight distribution (PDI < 1.3). Furthermore, the homopolymers can be reactivated to produce block copolymers. The RAFT agent, carboxymethyl dithiobenzoate (CMDB), proved to control molecular weight and PDI. As the RAFT agent concentration increases, molecular weight and PDI decreased. However, CMDB showed evidence of having a relatively low chain transfer constant as well as degradation during polymerization. Solution of the block copolymers in phosphate buffered saline displayed temperature reversible characteristics at a lower critical solution temperature (LCST) transition of 31°C. A 5 wt % solution of the block copolymers form thermoreversible gels by a self‐assembly mechanism above the LCST. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1191–1201, 2006     

Synthesis of block copolymers with thermodynamically compatible chain segments: di‐ and triblock copolymers of polystyrene and poly(2,6‐dimethyl‐1,4‐phenylene oxide)

Mono‐ and bifunctional poly(phenylene oxide) (PPO) macroinitiators for atom transfer radical polymerization (ATRP) were prepared by esterification of mono‐ and bishydroxy telechelic PPO with 2‐bromoisobutyryl bromide. The macroinitiators were used for ATRP of styrene to give block copolymers with PPO and polystyrene (PS) segments, namely PPO‐block‐PS and PS‐block‐PPO‐block‐PS. Various ligands were studied in combination with CuBr as ATRP catalysts. Kinetic investigations revealed controlled polymerization processes for certain ligands and temperature ranges. Thermal analysis of the block copolymers by means of DSC revealed only one glass transition temperature as a result of the compatibility of the PS and PPO chain segments and the formation of a single phase; this glass transition temperature can be adjusted over a wide temperature range (ca 100–199 °C), depending on the composition of the block copolymer. Copyright © 2005 Society of Chemical Industry     

Synthesis and characterization of ABA‐type triblock copolymers derived from polyimide and poly(2‐methyl‐2‐adamantyl methacrylate)

ABA‐type triblock copolymers derived from 4,4‐(hexafluoroisopropylidene)diphthalic anhydride‐2,3,5,6‐tetramethyl‐1,4‐phenylenediamine and 2‐methyl‐2‐adamantyl methacrylate (2‐MAdMA) were synthesized via atom transfer radical polymerization. The component ratios of polyimide (PI) and poly(2‐MAdMA) (PMAdMA) were about 8/2, 6/4 and 3/7, as determined using ¹H NMR spectroscopy and thermogravimetric analysis (TGA). The film structure of the triblock copolymers was dependent on the PI structure. Hydrophobicity increased as the component ratio of PMAdMA increased. Based on TGA, three‐step decomposition behaviors of all triblock copolymers derived from PI and PMAdMA in nitrogen and air atmosphere were observed. The gas permeability of the triblock copolymers was lower than that of PI. This finding can be attributed to the decrease in fractional free volume by the adamantane component and the decrease in permeability of the triblock copolymers compared with PI. The dielectric constant of the triblock copolymers was lower than that of PI. The dielectric constant was dependent on molar volume and molar porlarizability, and the dielectric constant derived from the symmetric structure of adamantane was reduced. The ABA‐type triblock copolymers derived from PI and PMAdMA can be considered as new polymer materials with high hydrophobicity, high H₂/CO₂ selectivity and low dielectric constant. © 2013 Society of Chemical Industry     

Preparation and morphology of amphiphilic polystyrene–poly (2‐vinylpyridine) heteroarm star copolymers prepared by ATRP

BACKGROUND: The self‐assembly of amphiphilic copolymers has been demonstrated to be a powerful route towards supramolecular objects with novel architectures, functions and physical properties. In this study, the synthesis and morphology of amphiphilic linear polystyrene (PS)‐block‐poly(2‐vinylpyridine) (P2VP) and heteroarm star PS‐star‐P2VP copolymers are studied. The dispersion of silver nanoparticles with the prepared PS‐block‐P2VP and PS‐star‐P2VP copolymers is also discussed. RESULTS: Amphiphilic copolymers with different P2VP chain lengths were successfully synthesized using atom transfer radical polymerization (ATRP). The copolymers prepared had low polydispersity indices. Various aggregate morphologies, including spheres, vesicles, rods, large compound micelles, two‐dimensional ring‐like and three‐dimensional hollow structures, were formed by varying the hydrophilic coil length and the selective solvent content. Silver nanoparticles showed good dispersion behavior in both types of copolymers. CONCLUSION: Based on this study, it will be possible to prepare metal/copolymer nanocomposites by direct mixing. Further, the PS‐block‐P2VP and PS‐star‐P2VP copolymers prepared can be used in the preparation of nanoporous films as templates and nanoparticles as nanoreactors. They can also be applied in terms of oil recovery, paints and cosmetics formulations, as well as in pharmaceutical and medical applications as rheological agents. Copyright © 2008 Society of Chemical Industry