Crystallization behavior of glass bead‐filled low‐density polyethylene composites

The effects of the filler content and the filler size on the crystallization and melting behavior of glass bead‐filled low‐density polyethylene (LDPE) composites have been studied by means of a differential scanning calorimeter (DSC). It is found that the values of melting enthalpy (ΔH_c) and degree of crystallinity (x_c) of the composites increase nonlinearly with increasing the volume fraction of glass beads, ϕ_f, when ϕ_f is greater than 5%; the crystallization temperatures (T_c) and the melting temperatures (T_m) of the composites are slightly higher than those of the pure LDPE; the effects of glass bead size on x_c, T_c, and T_m are insignificant at lower filler content; but the x_c for the LDPE filled with smaller glass beads is obviously greater than that of the filled system with bigger ones at higher ϕ_f. It suggests that small particles are more beneficial to increase in crystallinity of the composites than big ones, especially at higher filler content. In addition, the influence of the filler surface pretreated with a silane coupling agent on the crystallization behavior are not too outstanding at lower inclusion concentration. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 687–692, 1999     

Synthesis,characterization, and properties of flexible magnetic nanocomposites of cobalt ferrite–polybenzoxazine–linear low‐density polyethylene

A simple method for the preparation of magnetic nanocomposites consisting of cobalt ferrite (CF; CoFe₂O₄) nanoparticles, polybenzoxazine (PB), linear low‐density polyethylene (LLDPE), and linear low‐density polyethylene‐g‐maleic anhydride (LgM) is described. The composites were prepared by the formation of benzoxazine (BA)–CF nanopowders followed by melt blending with LLDPE and the thermal curing of BA. The composites were characterized by X‐ray diffraction, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy, universal testing machine measurement, and vibrating sample magnetometry. The composites consisting of LLDPE, PB, and LgM (47.5L–47.5PB–5LgM) exhibited a higher tensile strength (23.82 MPa) than pure LLDPE and a greater elongation at break (6.11%) than pure PB. The tensile strength of the composites decreased from 19.92 to 18.55 MPa with increasing CF loading (from 14.25 to 33.25 wt %). The saturation magnetization of the composites containing 33.25 wt % CF was 18.28 emu/g, and it decreased with decreasing amount of CF in the composite. The composite films exhibited mechanical flexibility and magnetic properties. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation and characterization of functionalized low density polyethylene matrix biocomposites

The incorporation of cellulosic fibers into polyethylene matrices was studied in this work, by dispersion of fluff pulp from maritime pine in a hot polymer solution, followed by co‐precipitation of the solid components by cooling at room temperature. The above method was found suitable for proper wetting and dispersion of fibers in the polymeric matrix, as compared with melt compounding. Unmodified low density polyethylene [LDPE], modified LDPE with maleic anhydride grafted linear low density polyethylene [M‐LLDPE] and a copolymer of acrylic acid and n‐butyl acrylate polyethylene [(AA/n‐BA)‐LDPE], were used as matrices for the preparation of fiber reinforced composites. The thermal properties of these composites were determined using differential scanning calorimetry and thermogravimetric analysis. The incorporation of cellulosic fibers results in a decrease of the crystallinity of the polymer matrix, as they act as inert material. In addition, the appropriate tests were run in order to determine the density and tensile properties of the composite specimens prepared by compression molding, with filler content ranging from 10 to 40% (w/w). Composites based on modified LDPE showed improved mechanical properties. The Takayanagi model, applied to predict the Young's modulus of composites, was in very good agreement with the experimental data obtained in this work. POLYM. ENG. SCI., 2008. © 2008 Society of Plastics Engineers     

Correlations between processing parameters,morphology, and properties of blown films of LLDPE/LDPE blends,part 2: Crystalline and amorphous biaxial orientation by WAXD pole figures

The biaxial molecular orientation of blown films made of blends of linear low density polyethylene (LLDPE) with low density polyethylene (LDPE) was characterized by two different methods: complete pole figures obtained by wide angle X‐rays diffraction (WAXD) and polarized infrared spectroscopy (IR) using the Krishnaswamy approach. The molecular orientation of the blends amorphous phase was also evaluated by polarized IR. The crystallinity of the blown films was determined by WAXD. A good correlation between the X‐ray pole figures and the polarized IR results was obtained. At all blends compositions, it was shown that the a‐axis of the polyethylene orthorhombic cell was preferentially oriented along the machine direction, the orientation degree along this direction increasing with the increase of the LDPE amount in the blends. The b‐axis changed its preferential orientation from film thickness in the 100/0 LLDPE/LDPE film to along the transverse direction with increasing LDPE in the blends. The c‐axis changed its orientation from orthogonal to normal direction in the 100/0 LLDPE/LDPE film to along the film thickness with increasing LDPE in the blends. Polarized IR characterization showed a negligible orientation of the amorphous phase. The amount of crystallinity was dependent on blend composition decreasing with the increase of LDPE content in the blends. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2760–2767, 2006     

Development of nanofibrous morphology in LDPE/LLDPE/PP blends and its effect on mechanical properties of blend films

Nanofibrous morphology has been observed in ternary blends of low density polyethylene (LDPE), linear low density polyethylene (LLDPE), and isotactic polypropylene (PP) when these were melt‐extruded via slit die followed by hot stretching. The morphology was dependent on the concentration of the component polymers in ternary blend LDPE/LLDPE/PP. The films were characterized by wide angle X‐ray diffraction (XRD), scanning electron microscopy (SEM), and testing of mechanical properties. The XRD patterns reveal that the β phase of PP is obtained in the as‐stretched nanofibrillar composites, whose concentration decreases with the increase of LLDPE concentration. The presence of PP nanofibrils shows significant nucleation ability for crystallization of LDPE/LLDPE blend. The SEM observations of etched samples show an isotropic blend of LDPE and LLDPE reinforced with more or less randomly distributed and well‐defined nanofibrils of PP, which were generated in situ. The tensile modulus and strength of LDPE/LLDPE/PP blends were significantly enhanced in the machine direction than in the transverse direction with increasing LLDPE concentration. The ultimate elongation increased with increasing LLDPE concentration, and there was a critical LLDPE concentration above which it increased considerably. There was a dramatic increase in the falling dart impact strength for films obtained by blow extrusion of these blends. These impressive mechanical properties of extruded samples can be explained on the basis of the formation of PP nanofibrils with high aspect ratio (at least 10), which imparted reinforcement to the LDPE/LLDPE blend. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Polyethylene with MoS2 nanoparticles toward antibacterial active packaging

Molybdenum disulfide (MoS₂) nanoparticles, obtained from liquid phase exfoliation in the presence of chitosan, were melt mixed with a linear low-density polyethylene (LLDPE) matrix to produce novel antimicrobial active packaging materials. The LLDPE/MoS₂ composites presented exfoliated nanoparticles forming aggregates that are well dispersed in the polymer matrix. These 2D-layered MoS₂ nanoparticles at concentrations of 0.5, 1.0, and 3.0 wt% rendered several functionalities to the LLDPE, as for example an antimicrobial behavior against Salmonella typhi and Listeria monocytogenes bacteria that can be explained not only by the photoactivity of the filler but also by changes in the composite surface. For instance, the composites presented a reduction in the water contact angle (i.e., an increased hydrophilicity) and relevant changes in the surface topography (i.e., reduced roughness) as compared with pure LLDPE. Regarding the barrier properties, while MoS₂ dramatically increased the water vapor permeation (WVP) of the polymer matrix, until 15 times for composite with 3.0 wt% of filler, the oxygen permeation decreased around 25%. All these novel functionalities in the nanocomposites were obtained without significantly affecting the tensile mechanical properties of the pure LLDPE matrix. These results show that MoS₂ is a promising filler for the development of antibacterial active packaging films with behaviors as similar as other 2D-layered fillers such as graphene derivatives.     

Mechanical,morphological, and thermal properties of poly(vinyl chloride)/low‐density polyethylene composites filled with date palm leaf fiber

This article investigates the mechanical, morphological, and thermal properties of poly(vinyl chloride) (PVC) and low‐density polyethylene (LDPE) blends, at three different concentrations: 20, 50, and 80 wt% of LDPE. Besides, composite samples that were prepared from PVC/LDPE blend reinforced with different date palm leaf fiber (DPLF) content, 10, 20, and 30 wt%, were also studied. The sample in which PVC/LDPE (20 wt%/80 wt%) had the greatest tensile strength, elongation at break, and modulus. The good thermal stability of this sample can be seen that T_10% and T_20% occurred at higher temperatures compared to others blends. DPLF slightly improved the tensile strength of the polymer blend matrix at 10 wt% (C10). The modulus of the composites increased significantly with increasing filler content. Ageing conditions at 80°C for 168 h slightly improved the mechanical properties of composites. Scanning electron microscopic micrographs showed that morphological properties of tensile fracture surface are in accordance with the tensile properties of these blends and composites. Thermogravimetric analysis and derivative thermogravimetry show that the thermal degradation of PVC/LDPE (20 wt%/80 wt%) blend and PVC/LDPE/DPLF (10 and 30 wt%) composites took place in two steps: in the first step, the blend was more stable than the composites. In the second step, the composites showed a slightly better stability than the PVC/LDPE (20 wt%/80 wt%) blend. Based on the above investigation, these new green composites (PVC/LDPE/DPLF) can be used in several applications. J. VINYL ADDIT. TECHNOL., 25:E88–E93, 2019. © 2018 Society of Plastics Engineers     

Mechanical strengths of molten and solidified LLDPE/LDPE blends and wood/LDPE composites under tensile deformation

The mechanical strengths of neat low‐density polyethylene (LDPE), a blend of LDPE with linear low‐density polyethylene (LLDPE), and a composite of LDPE with wood flour (wood/LDPE) were investigated in molten and solidified states under tensile deformation. The results are discussed in terms of the effects of LLDPE and wood contents, roller speed, and volumetric flow rate. In LLDPE/LDPE blends, incorporating LLDPE from 0 to 30 wt% into LDPE caused a slight increase in drawdown force, a larger fluctuation in drawdown force, and a reduction of maximum roller speed to failure. The mechanical properties of the solidified LLDPE/LDPE corresponded to those of the molten LLDPE/LDPE with regard to the effect of LLDPE content. For wood/LDPE composites, increasing the wood flour content in molten LDPE caused considerable reductions in drawdown time and maximum roller speed to failure. The drawdown force increased with increasing wood flour up to 10 wt% before it decreased at the wood loading of 20 wt%. A number of voids and pores on the extrudate surfaces became obvious for the composites with 20 wt% of wood content. Increasing wood content enhanced the tensile modulus for the solidified LDPE but decreased its tensile strength. Unlike those of LLDPE/LDPE blends, the changes in tensile modulus and strength of solidified wood/LDPE composites with wood content did not correspond to those of the molten composites. In all cases, the drawdown force increased with increasing roller speed. The effect of volumetric flow rate from the extruder on the mechanical strengths of the solidified blends was more pronounced than on those of the molten ones. J. VINYL ADDIT. TECHNOL., 2011. © 2011 Society of Plastics Engineers     

The effect of matrix composition on the properties of cellulosic fibers–polyethylene composites

The solution/precipitation method was used for the preparation of polyethylene (PE)/cellulosic fibers composites. Blends of modified linear low density PE [linear low density PE‐grafted maleic anhydride (LLDPE‐g‐MAH)] with low density PE (LDPE) were used as matrices for the aforementioned composites. Blends of LDPE with a copolymer of LDPE and acrylic acid (AA)/n‐butyl acrylate (n‐BA) [(AA/n‐BA)–LDPE] were also studied for the same purpose. The reinforcing effect of cellulosic fibers in terms of tensile strength is more enhanced when mixtures of the modified polar polymer with pure PE were used as matrices, as compared with that corresponding to matrices consisting of modified PE alone. Regarding the Izod impact strength, composites of LLDPE‐g‐MAH presented the best performance with an improvement of 135% in comparison with specimens consisting of LDPE matrix, whereas composites of (AA/n‐BA)‐LDPE matrix showed a modest improvement of their impact resistance. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Starch‐filled ternary polymer composites. II: Room temperature tensile properties

The room temperature tensile properties of granular starch‐filled low‐density polyethylene (PE) and starch‐filled blends of PE and poly(hydroxy ester ether) (PHEE) are presented. At low filler contents (?_f), the filled PE:PHEE blend has a higher yield stress and tensile strength than either the starch/PE composites or the unfilled matrix. The increase in the yield stress indicates that matrix yielding occurs before debonding. At high filler contents, the tensile strength of the filled blend is again greater than the strength of the starch/PE composites. This increase in strength is the result of higher debonding stresses in the ternary composite. In both materials there is a change in the deformation process at a critical filler content, ?_cr. Below ?_cr, deformation involves the growth of debonded regions; above ?_cr, deformation is confined to narrow damaged zones. There is a reduction in the strain at failure when this change in the deformation process occurs. Although the PHEE surface coating affects the debonding stress and the tensile strength, it does not affect the strain at failure or the tensile modulus. For both composite materials, the increase in modulus with ?_f can be adequately described using a simplified form of the Kerner equation. Polym. Eng. Sci. 44:1839–1847, 2004. © 2004 Society of Plastics Engineers.     

Thermal,electrical, and mechanical properties of Si3N4 filled LLDPE composite

Silicon nitride (Si₃N₄) filled linear low-density polyethylene (LLDPE) composite was prepared. The effects of Si₃N₄ filler content, dispersion, and LLDPE particle size on the thermal conductivity, and Si₃N₄ filled content on the mechanical and electrical properties of Si₃N₄ reinforced LLDPE composites prepared using powder mixing were investigated. The results indicate that there existed a unique dispersion state of Si₃N₄ particles in LLDPE, shell-kernel structure, in which Si₃N₄ particles surrounded LLDPE matrix particles. With increasing filler content and LLDPE particles size, thermal conductivity increased, and reached 1.42 W/m K at 30 vol% of filler, seven times as that of unfilled LLDPE. Furthermore, the examinations of Agari model demonstrate that larger size LLDPE particles form thermal conductive networks easily compared with smaller ones. The values predicted by theoretical model underestimate the thermal conductivity of Si₃N₄/LLDPE composites. In addition, the composites still possessed rather higher electrical resistivity and dielectric properties, but the mechanical properties decreased. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Studies on the physico‐mechanical,thermal, and morphological behaviors of high density polyethylene/coleus spent green composites

This study is aimed at utilizing nutraceutical industrial waste and reducing carbon footprints of plastics. Eco‐friendly “green composites” of high density polyethylene (HDPE) were fabricated using coleus spent (CS)—a nutraceutical industrial waste as reinforcing filler and maleic anhydride‐graft‐polyethylene (MA‐g‐PE) as compatibilizer. Composites were fabricated with 5, 10, 15, and 20% (w/w) of CS by extrusion method. The fabricated HDPE/CS composites were evaluated for mechanical and thermal behavior. A slight improvement of about 5% in tensile strength and marked improvement of about 25% in tensile modulus for 20 wt % CS filled HDPE composites was noticed. The effect of CS content on rheological behavior was also studied. Thermal characteristics were performed using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). TGA thermogram indicated increased thermal stability of CS‐filled composites. From TGA curves the thermal degradation kinetic parameters of the composites have been calculated using Broido's method. The enthalpy of melting (ΔH_m) obtained from DSC curves was reduced with increase in CS content in HDPE matrix, due to decrease in HDPE content in composite systems. An increase in CS loading increased the water absorption behavior of the composites slightly. Morphological behavior of cryo‐fractured composites has been studied using scanning electron microscopy. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of silane coupling agent on the curing,tensile, thermal,and swelling properties of ethylene‐propylene‐diene monomer rubber (EPDM)/mica composites

The influence of silane (bis[3‐triethoxysilylpropyl] tetrasulfide) coupling agent on the properties of ethylene‐propylene‐diene monomer rubber (EPDM)/mica composites was studied. Both EPDM/mica composites with silane and those without silane were compounded by using a two‐roll mill at various filler loadings (i.e., 100/0, 100/10, 100/30, 100/50, 100/70). The tensile and thermal properties as well as the fracture surfaces of the composites were investigated by using an Instron Universal Testing Machine, a thermal gravimetric analyzer, and a field emission scanning electron microscope. The results indicated that the optimum cure time (t₉₀) and scorch time (t_s2) values were shorter, whereas the maximum torque (M_H) value was slightly higher, for EPDM/mica composites with silane compared to those without silane. The tensile properties, modulus at 100% elongation, and modulus at 300% elongation increased for the composites made with silane, and the optimum filler loading for those properties was 50 parts by weight per hundred parts of rubber. In addition, thermal stability and swelling ratio for both composites improved with increased filler loading. However, the composites with silane showed better thermal stability and swelling ratio because of stronger linkage at the rubber‐filler boundary, which promoted filler dispersion. J. VINYL ADDIT. TECHNOL., 20:116–121, 2014. © 2014 Society of Plastics Engineers     

Effects of chemical modification of epoxy‐(ethylene diamine) on water hyacinth fibers (Eichhornia crassiper)‐filled (low‐density polyethylene)/(natural rubber) blends

The effects of modification by epoxy‐(ethylene diamine) (EED) on (water hyacinth fiber)‐filled (low‐density polyethylene)/(natural rubber) (LDPE/NR/WHF_‐EED) composites were studied. The LDPE/NR/WHF and LDPE/NR/WHF_‐EED composites were prepared by using a Brabender Plasticorder. LDPE/NR/WHF_‐EED showed higher tensile strength, Young's modulus, and elongation at break but lower molar sorption of toluene compared with LDPE/NR/WHF composites. The Fourier‐transform infrared radiation analysis indicated that the absorption peak at 1,648 cm^?1 exhibited the C? N band. This C? N band was formed from the bond of the epoxy group and the amine group in the WHF‐g‐epoxy‐(ethylene diamine) (WHF_‐EED). The scanning electron microscopic morphology of LDPE/NR/WHF_‐EED composites displayed rougher surfaces and less fiber pull, which improved the interfacial adhesion among the fiber/matrix. J. VINYL ADDIT. TECHNOL., 20:201–209, 2014. © 2014 Society of Plastics Engineers     

Correlations between processing parameters,morphology, and properties of blown films of linear low‐density polyethylene/low‐density polyethylene blends. I. Crystalline biaxial orientation by IR and mechanical properties

The change of the processing parameters of a blown film operation alters the mechanical and optical properties of the films. This work studied the influence of some of these parameters on the properties of blown films made of blends of linear low‐density polyethylene (LLDPE) and LDPE. Correlations between the crystalline biaxial orientations of these films and the mechanical properties were found. The crystalline biaxial orientation was measured by IR following the Krishnaswamy approach. The a axis of the unit cell was oriented along the machine direction (MD) at all LDPE concentrations, and it was not affected by the blow‐up ratio (BUR). In contrast, the b axis changed its orientation from orthogonal to MD to along the transverse direction (TD), and it was affected by the BUR. Finally, the c axis changed its orientation from equiplanar between the MD and TD to along the thickness of the film, and it was influenced by the BUR. The decrease of the tensile mechanical properties along the MD with the increase in the amount of LDPE in the blends was attributed to the tilting of the c axis toward the film thickness. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3161–3167, 2006     

Effect of blending high‐pressure low‐density polyethylene on the crystallization kinetics of linear low‐density polyethylene

It is well known that the addition of a small amount of high‐pressure low‐density polyethylene (HP‐LDPE) to linear low‐density polyethylene (LLDPE) can improve the optical properties of LLDPE, and LLDPE/HP‐LDPE blend is widely applied to various uses in the field of film. The optical haziness of polyethylene blown films, as a result of surface irregularities, is thought to be as a consequence of the different crystallization mechanisms. However, not much effort has been directed toward understanding the effect of HP‐LDPE blending on the overall crystallization kinetics (k) of LLDPE including nucleation rate (n) and crystal lateral growth rate (v). In this study, we investigated the effect of blending 20% HP‐LDPE on the crystallization kinetics of LLDPE polymerized by Ziegler‐Natta catalyst with comonomer of 1‐butene. Furthermore, by combining depolarized light intensity measurement (DLIM) and small‐angle laser light scattering (SALLS), we have established a methodology to estimate the lateral growth rate at lower crystallization temperatures, in which direct measurement of lateral growth by polarized optical microscopy (POM) is impossible due to the formation of extremely small spherulites. This investigation revealed that HP‐LDPE blending leads to enhanced nucleation rate, reduced crystal lateral growth rate, and a slight increase in the overall crystallization kinetics of pure LLDPE. From the estimated crystal lateral growth rate, it was found that the suppression in v from HP‐LDPE blending is larger at lower temperatures than at higher temperatures. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Silane grafting and moisture crosslinking of polyethylene: The effect of molecular structure

The silane grafting and moisture crosslinking of different grades of polyethylene have been investigated. Three types of polyethylene (HDPE, LLDPE, and LDPE) with different molecular structures and similar melt flow indices were selected. The initiator was dicumyl peroxide (DCP), and the silane was vinyltrimethoxysilane. The grafting reaction was carried out in an internal mixer. The extent of grafting and the degree of crosslinking were determined, and hot‐set tests were carried out to evaluate the crosslink structure of the different polyethylenes. The LLDPE had the highest degree of grafting, while the LDPE had the least. The rate of crosslinking for LDPE was higher than that of HDPE and LLDPE. The gel content of LDPE was higher than that of HDPE and LLDPE. Hot‐set elongation and the number‐average molecular weight between crosslinks (M_c) were lower for LLDPE and LDPE than for HDPE. Increasing the silane/DCP percentage led to peroxide crosslinking, thereby decreasing the M_c and hot‐set elongation. The number‐average molecular weight (M_n), molecular weight distribution, and number of chain branches were the most important parameters affecting the silane grafting and moisture crosslinking. J. VINYL ADDIT. TECHNOL., 2009. © 2009 Society of Plastics Engineers     

Fabrication of alumina based electrically conductive polymer composites

Novel electrically conductive composites were synthesized by incorporating Cu coated alumina (Cu‐Al₂O₃) powder prepared via electroless plating technique as filler (0–21wt %) into polystyrene‐b‐methylmethacrylate (PS‐b‐PMMA) and polystyrene (PS) matrices. XRD analysis depicted maximum Cu crystallite growth (26.116 nm～ plating time 30 min) onto Al₂O₃ along with a significant change in XRD patterns of composites with Cu‐Al₂O₃ inclusion. SEM–EDX analyses exhibited uniform Cu growth onto Al₂O₃ and confirmed presence of Cu, Al, Pd in Cu‐Al₂O₃, and C, O, Al, Cu, and Pd in PS‐b‐PMMA and PS composites. Increasing filler loadings exhibited increased electrical conductivity (5.55 × 10^?5S/cm for PS‐b‐PMMA; 5.0 × 10^?6S/cm for PS) with increased Young's modulus (1122MPa for PS‐b‐PMMA; 1053.9MPa for PS) and tensile strength (27.998MPa for PS‐b‐PMMA; 30.585MPa for PS) and decreased % elongation. TGA demonstrated increased thermal stability and DTG revealed two‐step degradation in composites while DSC depicted pronounced increment in T_g of Cu‐Al₂O₃/PS‐b‐PMMA with increased filler loading. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42939.     

Performance evaluation of synthesized acrylic acid grafted polyethylene in aluminum hydroxide highly filled polyethylene composites

A polymeric agent acrylic acid grafted polyethylene (AAgPE) was synthesized and used as a coupling agent in aluminum hydroxide [Al(OH)₃] highly filled linear low‐density polyethylene (LLDPE) composite. It is found that AAgPE improves the interfacial adhesion between the filler and the polyethylene matrix, which results in good mechanical properties of the composite. Silicon oil is an effective additive for improving the impact strength, the elongation at break, and the rheological property of the filled composite, but it decreases the tensile strength remarkably. The combination of AAgPE and silicon oil can lead to good performance of the composite. Flammability properties and fracture surface morphologies of the composites through scanning electron microscopy were investigated. The relationship between mechanical properties and microstructure of the composites was discussed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2544–2549, 2002     

Selective ethylene‐permeable zeolite composite double‐layered film for novel modified atmosphere packaging

The composite double‐layered films, for the packaging application of postharvest fruits and vegetables, were prepared by laminating low‐density polyethylene (LDPE) and poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) modified with zeolite ZSM‐5. The film was characterized by scanning electron microscope and differential scanning calorimeter and tested for permeation of ethylene (C₂H₄), oxygen (O₂), carbon dioxide (CO₂), and water vapor. It was found that the C₂H₄ permeability of the films was improved because of an enhanced adsorption of C₂H₄ by the incorporated zeolite (0–10 wt%). The preconcentrated layer (zeolite/SEBS) leads to a higher C₂H₄ concentration gradient across the film. Moreover, the high dispersion of zeolite increased the C₂H₄ permeation. When compared with O₂ and CO₂, the composite films were more selective to C₂H₄. However, the C₂H₄ permeation decreased in the presence of O₂ because of a competitive adsorption. In addition, the films possessed appreciate tensile properties for packaging application. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers