Kinetic analysis of radiation-initiated copolymerization reactions of water-soluble vinyl monomers with cellulose

A kinetic analysis of the radiation-initiated copolymerization reactions of 2-hydroxyethyl methacrylate (HEMA), hydroxypropyl methacrylate (HPMA), and methacrylic acid (MAA) from water, methanol (MeOH), N,N-dimethylformamide (DMF), dimethysulfoxide (DMSO), and combinations of these solvents with irradiated fibrous cellulose I and II was made. The maximum extent of copolymerization of HEMA and HPMA with irradiated cellulose occurred from water solutions. When organic solvents were added to the water solution, while the concentration of monomer was kept constant, the extent of copolymerization decreased. The maximum extent of copolymerization of MAA with irradiated cellulose occurred from mixtures of MeOH (15–30 vol-%) and water (85–70 vol-%) solutions rather than from water. After initiation of the copolymerization reactions, they were apparently diffusion controlled and exhibited second-order kinetics. The relative concentrations of grafted polymer and homopolymer formed with irradiated cellulose from aqueous solutions depended primarily on the concentration of water in the solutions. From MeOH (60 vol-% or less)–water (40 vol-% or more) solutions, about 60% of poly(MAA) formed was apparently grafted polymer; from solutions containing less water, the fraction of grafted polymer decreased to about 40%.     

Light cured fluoride filled denture‐coating materials

Light cured denture‐coating materials were prepared by formulating an acrylate monomer with a photoinitiator system (camphorquinone and dimethylaminoethyl methacrylate) using one of three base monomers [bisphenol A glycerolate diacrylate (Bis‐GDA), glycerol 1,3‐diglycerolate diacrylate (GDA), and diurethane dimethacrylate (DU‐DMA)] each with four diluents [triethylene glycol dimethacrylate (TEGDMA), di(ethylene glycol) methyl ether methacrylate, 2‐hydroxyethyl methacrylate (HEMA), and methacrylic acid (MAA)] at a fixed 1 : 1 molar ratio of base monomer to diluent. The twelve formulations were then evaluated for their surface hardness and water sorption as coating materials. The DU‐DMA/MAA, DU‐DMA/HEMA, Bis‐GDA/HEMA, and GDA/MAA based coatings provided a high level of both surface hardness and water sorption properties. When sodium fluoride (NaF) or calcium fluoride (CaF₂) was incorporated into those formulations, the fluoride ion release rate from all four NaF containing coating materials was extremely high in the first week, decreasing sharply in the second week and then decreasing in the later 2 weeks. In contrast, the CaF₂ containing coating materials showed a slower sustained rate of fluoride ion release over the 4‐week test period, with the DU‐DMA/HEMA based coating having a fluoride ion release pattern that meets the requirements for dental use. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Grafting vinyl monomers onto silk (Bombyx mori) using different initiators: Properties of grafted silk

The graft–copolymerization of silk with methacrylamide (MAA), 2‐hydroxyethyl methacrylate (HEMA), and methyl methacrylate (MMA) was studied using three different free‐radical initiators: an inorganic peroxide [ammonium persulfate (APS)] and two azo compounds [2,2′‐azobisisobutyronitrile (AIBN) and 2,2′‐azobis(2‐methylpropionamidine) dihydrochloride (ADC)]. The rate and yield of grafting followed the order: APS > AIBN > ADC. The performance of AIBN was close to that of APS in terms of weight gain attained. The degree of yellowing of grafted silk varied as a function of the initiator–monomer system used. APS induced the highest degree of yellowing, regardless of which monomer was used, whereas silk grafted with the MAA/AIBN system displayed the lowest level of yellowing. Moisture regain of grafted silk changed as a function of the hydrophilic/hydrophobic character of the grafted polymer, regardless of the kind of initiator used. Accordingly, tensile properties showed a tendency to decrease with increasing weight gain of grafted silk, the extent of which was independent of the kind of monomer and initiator used. The different initiators did not induce any appreciable change in the fine structure of silk, as demonstrated by optical measurements. Uneven surface deposition of homopolymer was detected to variable extent with MMA and HEMA grafting, whereas the surface of MAA‐grafted silk was completely free of any foreign deposit, independently of the initiator used. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 1401–1409, 2001     

Chitosan‐grafted poly(hydroxyethyl methacrylate‐co‐glycidyl methacrylate) membranes for reversible enzyme immobilization

Epoxy group‐containing poly(hydroxyethyl methacrylate/glycidyl methacrylate), p(HEMA/GMA), membrane was prepared by UV initiated photopolymerization. The membrane was grafted with chitosan (CH) and some of them were chelated with Fe(III) ions. The CH grafted, p(HEMA/GMA), and Fe(III) ions incorporated p(HEMA/GMA)‐CH‐Fe(III) membranes were used for glucose oxidase (GOD) immobilization via adsorption. The maximum enzyme immobilization capacity of the p(HEMA/GMA)‐CH and p(HEMA/GMA)‐CH‐Fe(III) membranes were 0.89 and 1.36 mg/mL, respectively. The optimal pH value for the immobilized GOD preparations is found to have shifted 0.5 units to more acidic pH 5.0. Optimum temperature for both immobilized preparations was 10°C higher than that of the free enzyme and was significantly broader at higher temperatures. The apparent K_m values were found to be 6.9 and 5.8 mM for the adsorbed GOD on p(HEMA/GMA)‐CH and p(HEMA/GMA)‐CH‐Fe(III) membranes, respectively. In addition, all the membranes surfaces were characterized by contact angle measurements. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3084–3093, 2007     

Polymerization of glycidyl methacrylate,methacrylic acid,acrylamide and their mixtures with cotton fabric using fe2+-thioureadioxide-H2O2 redox system

Polymerization of glycidyl methacrylate (GMA), methacrylic acid (MAA), acrylamide (Aam) and their binary mixtures with cotton cellulose fabrics using Fe²⁺-thioureadioxide-H₂O₂ redox system was investigated under a variety of conditions. While temperatures of 50, 80, 65, and 95°C constituted the optimal polymerization temperature for GMA, MAA, Aam and GMA/MAA (8:2), respectively, maximum polymerization of GMA/MAA (2:8), Aam/MAA (8:2) and Aam/MAA (2:8) occurred at 75°C. The polymerization reaction proceeded initially very fast then levelled off irrespective of the monomer or monomer mixtures used. However, the magnitude of the polymer add-on at levelling off of polymerization followed the order GMA > GMA/MAA (2:8) ≥ GMA/MAA (8:2) > Aam/MAA (2:8) ≥ MAA ≥ Aam/MAA (8:2) > Aam. The polymer add-on enhanced by increasing the H₂O₂ concentration up to a certain limit and then decreased. The same situation was encountered with respect to thioureadioxide concentration. The involvement of the epoxy ring of GMA with MAA during polymerization of their mixture with cellulose occurred only at a higher ratio of GMA in the mixture. Also a significant contribution of Aam in the polymer add-on obtained with a Aam/MAA mixture could only be achieved at a higher ratio of Aam in this mixture.     

Study of multi‐monomer melt‐grafting onto polypropylene in an extruder

Free‐radical melt‐grafting of the dual‐monomer systems glycidyl methacrylate–styrene (GMA‐St) and hydroxyethyl methacrylate–styrene (HEMA‐St) onto polypropylene (PP) has been studied using a single‐screw extruder. For single monomer grafting systems, degradation of PP was unavoidable and deterioration of the mechanical properties of the grafted PP subsequently occurred because of β‐scission of PP chains during the free‐radical melt‐grafting process. However, for the dual‐monomer systems, it is shown that the addition of styrene as a comonomer can significantly enhance the GMA or HEMA grafting levels on PP and reduce the extent of β‐scission of PP backbone. It has been found that the grafting degree of dual‐monomer melt‐grafted PP, such as PP‐g‐(GMA‐co‐St) or PP‐g‐(HEMA‐co‐St), is about quadruple that of single‐monomer grafted PP for the same monomer and dicumyl peroxide concentrations. Moreover, the melt flow rate of the dual‐monomer grafted PP is smaller than that of the unmodified PP. Hence, PP not only was endowed with higher polarity, but also kept its good mechanical properties. © 2000 Society of Chemical Industry     

Chiral copolymers of (R)‐N‐(1‐phenylethyl) methacrylamide and 2‐hydroxyethyl methacrylate: copolymerization characteristics and chiroptical properties

The aim of this investigation was the copolymerization of a chiral monomer, (R)‐N‐(1‐phenylethyl) methacrylamide, with an achiral monomer, 2‐hydroxyethyl methacrylate (HEMA). The copolymerization characteristics as well as the chiroptical properties (optical rotation and circular dichroism) and their variation with copolymer composition and temperature are discussed. The copolymers are statistical and enriched in HEMA. The monomer reactivity ratio of the chiral monomer (r₁) is 0.133 whereas that of HEMA (r₂) is 1.042 based on the Kelen–Tudos method. The sequence of consecutive chiral monomer units predominates for a feed composition between 0.5 and 0.9 (mole fraction). On the other hand, the sequence of HEMA is uniform and it predominates for a feed composition of around 0.5 (mole fraction). The chiroptical properties of the copolymers do not vary linearly with the content of chiral units in the copolymers. The optical rotation and circular dichroism attain optimum values above 30–40 mol% of chiral monomer units in the copolymers. However, the circular dichroism of the copolymers varies linearly with the temperature. The chiral monomer being a more bulky structure is less reactive than HEMA. The nonlinear variation of chiroptical properties of the copolymers with the content of chiral units may be due to the secondary interaction in the copolymers associated with the hydrogen bonding involving the amide linkage (CONH) present in the pendant chromophore of the chiral monomer as well as the hydroxyl pendant group of HEMA and also the aromatic π–π interaction. Copyright © 2009 Society of Chemical Industry     

Preparation and properties of novel dentin adhesives with esterase resistance

A new methacrylate monomer, trimethylolpropane mono allyl ether dimethacrylate (TMPEDMA), was synthesized and evaluated. This branched methacrylate was designed to increase esterase‐resistance when incorporated into conventional HEMA (2‐hydroxyethyl methacrylate)/BisGMA (2,2‐bis[4(2‐hydroxy‐3‐methacryloyloxy‐propyloxy)‐phenyl] propane) dental adhesives. The new adhesives, HEMA/BisGMA/TMPEDMA in a 45/30/25 (w/w) ratio were formulated with H₂O at 0 (A0T) and 8 wt % water (A8T) and compared with control adhesives (HEMA/BisGMA, 45/55 (w/w), at 0 (A0) and 8 wt % (A8) water). Camphoroquinone (CQ), 2‐(dimethylamino) ethyl methacrylate and diphenyliodonium hexafluorophosphate were used as photoinitiators. The new adhesives showed a degree of conversion comparablewith the control and improved modulus and glass transition temperature (T_g). Exposure of photopolymerized discs to porcine liver esterase for up to eight days showed that the net cumulative methacrylic acid (MAA) release in adhesives formulated with the new monomer and 8% water (A8T: 182 μg/mL) was dramatically (P < 0.05) decreased in comparison to the control (A8: 361.6 μg/mL). The results demonstrate that adhesives made with the new monomer and cured in water to simulate wet bonding are more resistant to esterase than conventional HEMA/BisGMA adhesive. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Functional,uniform, and macroporous latex particles: Preparation,electron microscopic characterization,and nonspecific protein adsorption properties

A series of uniform, macroporous particles with different surface chemistries were prepared with different acrylic comonomers [methyl methacrylate (MMA), butyl methacrylate (BMA), epoxypropyl methacrylate (EPMA), 2‐hydroxyethyl methacrylate (HEMA), and methacrylic acid (MAA)] with styrene–divinylbenzene (S–DVB) in a multistep seeded polymerization. In the synthesis, uniform polystyrene seed particles 6.2 μm in size were swollen first with a low molecular weight organic agent and then with a monomer phase including an S–DVB mixture and a relatively polar acrylic monomer. Final macroporous particles approximately 10 μm in size were obtained by the repolymerization of the monomer phase in the swollen seed particles. Surface and bulk morphologies were investigated with scanning and transmission electron microscopy, respectively. Although highly porous particles could be achieved with relatively hydrophobic monomers such as styrene, BMA, MMA, and EPMA, the use of hydrophilic monomers such as HEMA and MAA led to the synthesis of uniform particles with lower macroporosity. A comparison of Fourier transform infrared and Fourier transform infrared/diffuse reflectance spectroscopy spectra indicated that the concentration of polar acrylic monomer on the surface was higher than in the bulk structure. The nonspecific protein adsorption behavior of uniform, macroporous particles was investigated with albumin as a model protein. The highest nonspecific albumin adsorption was observed with plain poly(styrene‐co‐divinylbenzene) [poly(S–DVB)] particles. The particles produced with MMA and EPMA also exhibited albumin adsorption capacities very close to that of plain poly(S–DVB). Reasonably low nonspecific albumin adsorption was observed with the particles produced in the presence of MAA, HEMA, and BMA. Poly(S–DVB) particles functionalized with poly(vinyl alcohol) provided nearly zero nonspecific albumin adsorption. For nonspecific albumin binding onto the particles via a physical adsorption mechanism, desorption ratios higher than 80% could be achieved. The desorption ratio with the EPMA‐carrying particles was only 5% because the albumin adsorption onto EPMA‐carrying particles occurred predominantly with covalent‐bond formation. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 414–429, 2002; DOI 10.1002/app.10412     

Effect of GMA on monodisperse epoxy‐functionalized polymer microsphere particles by dispersion copolymerization of styrene with glycidyl methacrylate

Monodisperse poly[styrene‐co‐glycidyl methacrylate (GMA)] microparticles were synthesized by dispersion copolymerization in a water–ethanol medium. The effects of various polymerization parameters on the particle size and size distribution of the dispersion copolymerization were investigated. The dispersion of polymer particles decreased when the GMA was added if the polystyrene homopolymer particles were polydispersed. The GMA acted as a comonomer as well as a costabilizer in the dispersion copolymerization of styrene with GMA. The solvency of the monomer increased with the concentration of GMA in the polymerization medium because GMA has a greater hydrophilicity than styrene, resulting in a large particle size and a slow polymerization rate. From an HCl–dioxane analysis of the poly(styrene‐co‐GMA) microparticles, great amounts of epoxy groups were detected after the completion of dispersion copolymerization. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1206–1212, 2001     

Lamination of conductive polypyrrole films to poly(tetrafluoroethylene) films via interfacial graft copolymerization

A simple technique for the lamination of a conductive polymer film to an inert dielectric polymer film was demonstrated. The electrochemically synthesized and p‐toluenesulfonic acid‐doped polypyrrole (PPY) film was laminated simultaneously to the argon plasma‐pretreated PTFE film during the thermally induced graft copolymerization of the PTFE surface with a functional monomer. The graft copolymerization was carried out using glycidyl methacrylate (GMA) monomer containing 20% v/v hexamethyldiamine (HMDA) and in the absence of any polymerization initiator. Thermally induced graft copolymerization of the GMA monomer on the PPY surface was minimal. The lap shear and T‐peel adhesion strengths of the laminates were found to be dependent on the GMA graft concentration on the PTFE surface, which, in turn, was affected by the plasma pretreatment time of the film. To increase the GMA graft concentration for the enhancement of adhesion strength, the plasma‐pretreated PTFE surfaces were premodified via UV‐induced graft copolymerization with GMA prior to the simultaneous thermal graft copolymerization and lamination process. The modified surfaces and interfaces were characterized by X‐ray photoelectron spectroscopy (XPS). Through XPS measurements of the delaminated surfaces, it was found that the PPY/PTFE laminates failed predominantly by cohesive failure inside the PTFE substrate. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 716–727, 2001     

Effect of partitioning of monomer on the reactivities of monomers in microemulsion

Copolymerization of styrene and 2‐hydroxyethyl methacrylate (2‐HEMA) was carried out in a microemulsion medium. The composition of the copolymers was estimated using proton ¹H‐NMR. The reactivity ratios of styrene and 2‐HEMA in ternary microemulsions were observed and were considerable different from those reported for solution and bulk polymerization. In monomer pairs with a considerable difference in polarity, partitioning of a monomer between the aqueous phase and the microemulsion droplets develops a concentration gradient, which can be calculated from the distribution coefficient of the monomer between the two phases. This approach has led to more reliable reactivity ratios for the monomers. The study of styrene–2‐HEMA copolymerization in a sodium dodecylsulfate‐based microemulsion resulted in r_S = 3.79 and r_H = 0.17 as apparent reactivity ratios and r_S = 0.57 and r_H = 23.24 as true reactivity ratios for styrene and 2‐HEMA, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1832–1837, 2002; DOI 10.1002/app.10401     

Grafting of vinyl monomers onto silk using redox systems. Yellowing of silk

The aim of this study is to investigate the influence of temperature, initiator concentration, and vinyl monomer on silk yellowing during grafting. A series of silk fabrics was treated at four different temperatures (70, 75, 80, and 88°C), with different concentrations of initiator in the range 1–4% owf, with and without methacrylamide (MAA) or 2-hydroxyethyl methacrylate (HEMA). By treating silk with ammonium persulphate (APS), in the absence of a monomer, the degree of silk yellowing increased linearly with increasing both initiator concentration and treatment temperature, indicating that the initiator plays a specific role in enhancing silk yellowing through macroradical formation. The graft copolymerization of MAA (with APS as the initiator) caused only slight changes in the intensity of silk yellowing compared to blank-treated fabrics. On the other hand, the use of HEMA resulted in a deeper yellowing of silk fabrics, especially in the 70–80°C temperature range, due to its higher reactivity and to the tendency to form a homopolymer, leaving unreacted macroradicals on silk fibroin backbone. Compared to APS, other initiators, such as 2,2′-azobis(isobutyronitrile) (AIBN) and 2–2′-azobis-(2-amidino propane) dihydrochloride (ADC), caused a significantly lower degree of silk yellowing when tested in the absebce of a monomer. The yellowness of silk fabrics tended to increase by grafting with HEMA, while decreased by grafting with MAA. The use of variable amounts of monomer (25–150% owf) did not influence the degree of yellowing with ADC as the initiator. The results reported in this study show that the extent of yellowing induced on silk fabrics by grafting MAA and HEMA with APS as the initiator can be limited by a suitable selection of the processing parameters (initiator concentration, temperature). Moreover, the use of both AIBN and ADC appears promising, owing to their negligible effect on silk yellowing. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 239–246, 1998     

Thermomechanical properties and morphology of interpenetrating polymer networks of polyurethane–poly(methyl methacrylate)

Interpenetrating networks (IPNs) of polybutadiene‐based polyurethane (PU) and poly(methyl methacrylate) (PMMA) were synthesized. The effect of the incorporation of 2% glycidyl methacrylate (GMA) and 2‐hydroxyethyl methacrylate (2‐HEMA) on the thermal, mechanical, and morphological properties of IPNs was investigated. Both 2‐HEMA and GMA led to improvements in these properties. However, 2‐HEMA‐containing IPNs showed somewhat better tensile strength, elongation, and damping characteristics. The morphology of IPNs containing 2‐HEMA showed better mixing of the components. The improvement in the properties was observed for up to 40% PMMA in the IPNs. Differential scanning calorimetry thermograms showed the presence of three glass transitions. The third glass‐transition temperature was explained by possible grafting of methyl methacrylate onto PU. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1576–1585, 2002     

Synthesis of well‐defined comb‐like amphiphilic copolymers with protonizable units in the pendent chains: 1. Preparation of narrow polydispersity copolymers of methyl methacrylate and 2‐hydroxyethyl methacrylate by atom‐transfer radical polymerization

Well‐defined methyl methacrylate (MMA) and 2‐(trimethylsiloxy)ethyl methacrylate (Pro‐HEMA) copolymers were prepared by atom‐transfer radical polymerization(ATRP), using CuCl/2,2′‐bipyridine as catalytic system and p‐toluenesulfonyl chloride as initiator. ATRP process of MMA and Pro‐HEMA was monitored by ¹H NMR, and the kinetic curves of the MMA/Pro‐HEMA copolymerization were plotted in terms of the ¹H NMR data. At low content of Pro‐HEMA in the feed composition, the copolymerization can be well controlled with the molecular weight, polydispersity and the monomer distribution in the copolymer chain. With the increase of Pro‐HEMA content in the feed mixture, the composition of the final copolymer deviates from the composition of the feed mixture gradually, and gradient copolymers of MMA/Pro‐HEMA can be obtained. Through the hydrolysis process, well‐defined copolymers of MMA/HEMA were obtained from poly(MMA/Pro‐HEMA). Copyright © 2003 Society of Chemical Industry     

Reactivity ratios and copolymer properties of 2‐(diisopropylamino)ethyl methacrylate with methyl methacrylate and styrene

Free radical copolymerization kinetics of 2‐(diisopropylamino)ethyl methacrylate (DPA) with styrene (ST) or methyl methacrylate (MMA) was investigated and the corresponding copolymers obtained were characterized. Polymerization was performed using tert‐butylperoxy‐2‐ethylhexanoate (0.01 mol dm^?3) as initiator, isothermally (70 °C) to low conversions (<10 wt%) in a wide range of copolymer compositions (10 mol% steps). The reactivity ratios of the monomers were calculated using linear Kelen–Tüd?s (KT) and nonlinear Tidwell–Mortimer (TM) methods. The reactivity ratios for MMA/DPA were found to be r₁ = 0.99 and r₂ = 1.00 (KT), r₁ = 0.99 and r₂ = 1.03 (TM); for the ST/DPA system r₁ = 2.74, r₂ = 0.54 (KT) and r₁ = 2.48, r₂ = 0.49 (TM). It can be concluded that copolymerization of MMA with DPA is ideal while copolymerization of ST with DPA has a small but noticeable tendency for block copolymer building. The probabilities for formations of dyad and triad monomer sequences dependent on monomer compositions were calculated from the obtained reactivity ratios. The molar mass distribution, thermal stability and glass transition temperatures of synthesized copolymers were determined. Hydrophobicity of copolymers depending on the composition was determined using contact angle measurements, decreasing from hydrophobic polystyrene and poly(methyl methacrylate) to hydrophilic DPA. Copolymerization reactivity ratios are crucial for the control of copolymer structural properties and conversion heterogeneity that greatly influence the applications of copolymers as rheology modifiers of lubricating oils or in drug delivery systems. © 2015 Society of Chemical Industry     

Preparation and characterization of polyelectrolyte copolymers containing methyl methacrylate and 2-hydroxyethyl methacrylate. I. Polymers based on methacrylic acid

Acidic polyelectrolyte copolymers containing 2-hydroxyethyl methacrylate (HEMA), methyl methacrylate (MMA), and methacrylic acid (MAA) were prepared by free radical polymerization to high conversion in solution. Copolymer yields were obtained by gravimetry (all in the 30–50% range), relative molecular weights estimated by intrinsic viscosity measurements (all in the 50–70 cc/g range), tacticity by ¹³C nuclear magnetic resonance (NMR) spectroscopy (all polymers predominantly syndiotactic with some atactic content), and composition by acid/base titrations in conjunction with ¹H-NMR spectroscopy (all close to the monomer charge ratios). Acid strengths or apparent pKa's were examined as a function of extent of ionization. Measurements performed in water indicated that the compact/extended coil transformation in predominantly syndiotactic polymethacrylic acid occurs also in copolymers of similar tacticity containing moderate to high concentrations of MAA. The apparent pKa of such polymers containing only small amounts of MAA did not vary with extent of ionization, indicating a low degree of interaction between the acid groups. In copolymer pairs containing similar amounts of MAA but differing HEMA and MMA contents, the polymer containing more HEMA appeared the stronger acid, presumably due to a better solvation of that polymer which would increase the net spatial charge–charge separation and decrease cooperative effects that lead to suppressed ionization.     

Functionalization of high‐density polyethylene in the molten state by glycidyl methacrylate grafting

:This study concerns the melt‐free radical grafting of glycidyl methacrylate (GMA) onto high‐density polyethylene (HDPE). We studied the effect of two initiators (tert‐butyl cumyl peroxide and di‐tert‐butyl peroxide) onto HDPE. Crosslinking of polymer was observed in the presence of 0.3 wt % tert‐butyl cumyl peroxide but not with 0.3 wt % di‐tert‐butyl peroxide. The grafting was carried out in a Brabender batch mixer at 190 °C. The grafting yield of GMA onto HDPE (determined by infrared spectrometry) is weak (<1 wt % for an initial concentration in monomer of 6 wt %). Moreover, it was noted that the degree of grafting did not vary with the concentration and the nature of peroxide used. To increase the grafting yield of GMA, we added to the HDPE/peroxide/GMA system an electron‐donating monomer, such as styrene. Adding this comonomer multiplied the rate of grafted GMA 3‐ or 4‐fold, resulting in a ratio [styrene]_i/[GMA]_i = 1 mol/mol with [GMA]_i = 6 wt %. So, the copolymerization is favored compared with the homopolymerization. This kind of copolymer presenting reactive functions is very attractive in the field of compatibilizing immiscible polymers. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 581–590, 2001     

Poly(hydroxyethyl methacrylate‐co‐glycidyl methacrylate) reactive membrane utilised for cholesterol oxidase immobilisation

Poly(2‐hydroxyethyl methacrylate‐co‐glycidyl methacrylate) p(HEMA–GMA) membrane was prepared by UV‐initiated photopolymerisation of 2‐hydroxyethyl methacrylate (HEMA) and glycidyl methacrylate (GMA) in the presence of an initiator, azobisisobutyronitrile (AIBN). Cholesterol oxidase was immobilised directly on the membrane by forming covalent bonds between its amino groups and the epoxide groups of the membrane. An average of 53 µg of enzyme was immobilised per cm² of membrane, and the bound enzyme retained about 67% of its initial activity. Immobilisation improved the pH stability of the enzyme as well as its temperature stability. The optimum temperature was 5 °C higher than that of the free enzyme and was significantly broader. The thermal inactivation rate constants for free and immobilised preparations at 70 °C were calculated as k_{i (free)} 1.06 × 10^?1 min^?1 and k_{i (imm)} 2.68 × 10^?2 min^?1, respectively. The immobilised enzyme activity was found to be quite stable in the repeated experiments. © 2002 Society of Chemical Industry     

Synthesis and polymerization of a new iodine‐containing monomer

A new iodine‐containing methacrylate monomer, 3,4,5‐triiodobenzoyloxyethyl methacrylate (TIBEM), was synthesized by coupling 2‐hydroxyethyl methacrylate (HEMA) with 3,4,5‐triiodobenzoic acid. The monomer was characterized by ¹H nuclear magnetic resonance, infrared (IR), and ultraviolet spectra. Homopolymerization and copolymerization of the monomer with methyl methacrylate (MMA) were carried out using 2,2′‐azobis isobutyronitrile as the initiator. A terpolymer of TIBEM, MMA, and HEMA was also synthesized. The copolymers were characterized by IR, gel permeation chromatography, differential thermal analysis, and thermogravimetric analysis (TGA). High molecular weight polymers were produced with MMA at different feed compositions of TIBEM. The polymers were found to be freely soluble in common solvents for acrylic polymers. TGA showed little decomposition of the copolymer below 280°C. Copolymers showed good radiopacity at 25 wt % of TIBEM in the feed. These copolymers could find applications in medical and dental areas where radiopacity is a desirable feature of the implants. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2580–2584, 2003