Morphology of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized by a methyl methacrylate/maleic anhydride copolymer

The morphologies of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized with a methyl methacrylate/maleic anhydride copolymer, with 3–20 wt % maleic anhydride, were examined by transmission electron microscopy. Some staining techniques were employed for identifying the various phases. The binary blends were immiscible and exhibited poor mechanical properties that stemmed from the unfavorable interactions among their molecular segments. This produced an unstable and coarse phase morphology and weak interfaces among the phases in the solid state. The presence of the copolymer in the blends clearly led to a more efficient dispersion of the acrylonitrile–butadiene–styrene phase and consequently optimized Izod impact properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3512–3518, 2003     

Polyethylenes/PET blend compatibilization with maleic anhydride modified polyethylenes obtained by a UV preirradiation process

The compatibilization of HDPE/LDPE/LLDPE/PET blend during reactive extrusion, using compatibilizing agents, such as modified high, low, and lineal low density polyethylenes with maleic anhydride, was carried out. The agents were prepared in our laboratory by using a UV preirradiation process, containing different grafting and crosslinking degrees. The materials were compared with same maleic anhydride modified polyethylenes prepared by the traditional peroxide method in our laboratory and with a commercial maleic anhydride modified lineal low density polyethylene. The mechanical and thermal properties, as well as their morphology, were evaluated in the compatibilized blends and changes in crystallization phases recorded. The elongation at break and impact strengths increased with compatibilization level and morphology was markedly more homogenous. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 560–567, 2007     

POE马来酸酐接枝物增韧PBT

将马来酸酐和POE进行接枝反应 ,反应后的POE马来酸酐共聚物POE MAH和PBT有很好的相容性 ,随着POE MAH加入量的增加 ,PBT的增韧效果有很大的提高。     

弹性体接枝马来酸酐对PP/PA6 的增容作用

以4种弹性体接枝马来酸酐(MAH)共聚物作为聚丙烯/聚酰胺6(PP/PA6)共混体系的增容剂,从界面相互作用、形态结构和力学性能等方面比较了它们的增容作用。乙烯-辛烯共聚物接枝马来酸酐(POE-g-MAH)和乙丙三元共聚物接枝MAH(EPDM-g-MAH)使PP与PA6两相间的界面相互作用增强,增容效果较好;POE-g-MAH为增容剂时,PA6粒子分布较均匀,粒径约为1μm。POE-g-MAH能明显改善PP/PA6共混体系的韧性和强度,具有良好的增容作用。当w(POE-g-MAH)为10%时,w(PA6)为60%的共混体系拉伸强度最高,达到53.4MPa;适当增加PA6用量,可明显改善共混体系的流动性。     

Mechanical and morphological study of polyphenylene sulfide/liquid crystalline polymer blends compatibilized with a maleic anhydride grafted copolymer

Blends of thermotropic liquid crystalline polymer (LCPA‐950), based on a copolyester of hydroxynapthoic acid and hydroxybenzoic acid with an engineering thermoplastic, poly(phenylene sulfide) (PPS), were prepared using a corotating twin‐screw extruder. Addition of a third component, a functionalized polypropylene (maleic anhydride grafted polypropylene, MA‐PP), that interact with the thermotropic liquid crystalline polymer (TLCP) facilitates the structural development of the TLCP phase by acting as a compatibilizer at the interface. Differential scanning calorimetry and dynamic mechanical thermal analysis results, however, show that there is an interaction between the polymers in the presence of compatibilizer. This means that MA‐PP can be used as a compatibilizer for the PPS/LCP in situ composite system. The viscosity of the compatibilized in situ composite was decreased by the compatibilizer, and this is mainly due to the fibrous structure of the LCP at the high shear rate. The mechanical properties of the ternary blends were increased when a proper amount of MA‐PP was added. This is attributed to fine fibril generation induced by the addition of MA‐PP. Morphological observations determined the significance of the third component in immiscible polymer blends, and an optimum amount of MA‐PP exists for the best mechanical performance. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Toughening of recycled poly(ethylene terephthalate) with a maleic anhydride grafted SEBS triblock copolymer

Toughening of recycled poly(ethylene terephthalate) (PET) was carried out by blending with a maleic anhydride grafted styrene‐ethylene/butylene‐styrene triblock copolymer (SEBS‐g‐MA). With 30 wt % of the SEBS‐g‐MA, the notched Izod impact strength of the recycled PET was improved by more than 10‐fold. SEM micrographs indicated that cavitation occurred in just a small area near the notch root. Addition of 0.2 phr of a tetrafunctional epoxy monomer increased the recycled PET melt viscosity by chain extension reaction. Different from the positive effect of the epoxy monomer in toughening of nylon and PBT with elastomers, the use of the epoxy monomer in the recycled PET/SEBS‐g‐MA blends failed to further enhance dispersion quality and thus notched impact strength. This negative effect of the epoxy monomer was attributed to the faster reactivity of the epoxy group with maleic anhydride of the SEBS‐g‐MA than with the carboxyl or hydroxyl group of recycled PET. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1462–1472, 2004     

顺酐化聚苯乙烯对PVC/SEBS共混物的增容作用

以顺酐化聚苯乙烯(PS-g-MAH)为增容剂,研究了苯乙烯-乙烯-丁烯-苯乙烯嵌段共聚物(SEBS)对聚氯乙烯(PVC)的共混增韧改性,讨论了该共混物在常温、低温下的力学性能及动态力学性能。结果表明,PS-g-MAH能明显改善SEBS与PVC的相容性,使PVC/SEBS共混物中分散相颗粒尺寸明显减小,分布更均匀,共混物的玻璃化转变温度内移,常温和低温下缺口冲击强度增大。当PVC/PS-g-MAH/SEBS(质量比)为75/6/25时,共混物的常温缺口冲击强度为50.6 kJ/m2,低温(-20℃)缺口冲击强度为29.8 kJ/m2。     

蒙脱土插层尼龙66及其合金力学性能研究

先采用有机化蒙脱土(org MMT)插层尼龙66制得了PA66/PP纳米复合材料,对其力学性能进行了测试。试验结果表明:MMT含量为7%时,PA66/MMT的各项性能达到最优,但是材料的韧性仍较差,进而采用与聚丙烯共混改性的方法增韧制得PA66/PP/MMT纳米复合材料,当MMT含量为5%,PA66∶PP为80∶20时,材料的冲击强度提高45 4%,而其他各项性能基本保持不变。     

Mechanical properties of blends of polycarbonate with unmodified and maleic anhydride grafted ABS

Blends of polycarbonate/acrylonitrile–butadiene–styrene terpolymer (PC/ABS) and polycarbonate/maleic anhydride grafted ABS (PC/MABS) were prepared over the whole range of compositions using a single-screw extruder. Tensile, flexural, notched Izod impact properties, and the heat deflection temperature of these blends were determined. Mechanical properties of PC/MABS blends are nearly equal to or higher than, those predicted by the rule of mixtures, whilst those of PC/ABS blends show nearly equal, or negative deviation, from the rule of mixtures. The notched impact strength of PC/MABS blends shows a positive blending effect and proportionate increase from 25wt% PC to 75wt% PC. Scanning electron micrographs were taken of etched surfaces of selective blends. © 1998 SCI.     

苯乙烯-异戊二烯-苯乙烯嵌段共聚物及其接枝马来酸酐增韧聚苯乙烯/纳米碳酸钙复合材料

以过氧化二异丙苯（DCP）为引发剂,通过单螺杆挤出机熔融挤出,制备了苯乙烯-异戊二烯-苯乙烯接枝马来酸酐（SIS—MAH）,研究了SIS及SIS—MAH对聚苯乙烯（Ps）／纳米碳酸钙（nano—CaCO3）复合材料物理、力学性能的影响,对其结构进行了表征。结果表明,MAH的用量宜为SIS质量分数的3％,DCP的用量应小于MAH质量分数的0．3％;当1份nano—CaCO3加入到PS／SIS（质量比100／2）复合材料3中,SIS与nano—CaCO3产生协同增韧效应,复合材料的无缺口冲击强度可提高到9．83kJ／m^2,但其缺口敏感性增大;SIS—MAH较SIS对PS／nano—CaCO3复合材料具有更好的增韧效果,接枝率为3．08％的SIS—MAH改性PS／CaCO3复合材料（质量比100／5／6）的无缺口冲击强度可提高到11．69kJ／m^2;当SIS用量为6份时,SIS改性复合材料不发生弯曲断裂;当SIS—MAH用量为2份时,SIS—MAH改性复合材料不发生弯曲断裂。     

Compatibilization and characterization of blends of styrene–maleic anhydride copolymer with modified polyethylenes

Potentially reactive blends of styrene–maleic anhydride (SMAH) with ethylene/methyl acrylate/glycidyl methacrylate (E‐MA‐GMA) and nonreactive blends of SMAH with ethylene/methyl acrylate (E‐MA) were produced in a Brabender batch mixer and in a corotating twin‐screw extruder. The products were characterized in terms of rheology, morphology, and mechanical properties to understand the reaction characteristics between anhydride/epoxy functional groups. Storage modulus, G′, loss modulus, G″ and complex viscosity, η* of the reactive blends were higher than those of nonreactive ones. At 25% E‐MA‐GMA content, maximum in η* was obtained for the reactive blends. The reactive blends showed finer morphology than the nonreactive ones at all concentrations studied. Mechanical characterization showed that reactive SMAH/E‐MA‐GMA blends had higher tensile strength, % strain at break, and tensile modulus than the nonreactive blends for all corresponding modified polyethylene contents. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 790–797, 2001     

Multiple melting behavior of polyphenylene sulfide blends with polyamide 6

Although there are many studies on the multiple melting behavior of polyphenylene sulfide (PPS) homopolymer, similar investigations on PPS component in PPS blends with thermoplastics are relatively rare. In the present paper, the multiple melting behavior of PPS blends with polyamide 6 (PA6) have been investigated by differential scanning calorimetry (DSC). The double melting peaks are also observed for PPS in the blends. Although the annealing temperature and time as well as the heating rate of DSC scanning are different, the lower melting peak temperature of PPS in the blend is higher than that of pure PPS and the higher melting peak temperature is lower than that of pure PPS. It is suggested that PA6 can accelerate the cold‐crystallization of amorphous PPS due to the possible presence of interfacial interaction between the component polymers to induce the heterogeneous nucleation, and increase the perfection of PPS crystals. The multiple melting behavior of PPS in the blends are explained by recrystallization. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1579–1585, 2000     

Reactions of low molecular weight highly functionalized maleic anhydride grafted polyethylene with polyetherdiamines

Reaction between low molecular weight highly functionalized maleic anhydride grafted polyethylene and several diamines were carried out using xylene as a reaction media. The influence of varying the amine to maleic anhydride (NH₂/MAH) molar ratio and chain length of diamine on reaction was investigated. It was shown that the reactions of these materials cannot be followed by FTIR measurements alone. In these examples, colorimetric titrations were used to assess residual acid/anhydride content that was not detected by FTIR. The reaction between anhydride and amine was observed to be fast. The degree of reaction and crosslinking in the reactor was observed to depend on the concentration of the reaction mixture and the NH₂/MAH molar ratio. In some cases, a gelatinous insoluble mass was produced in the reactor and this material was not easily processed for further characterization. All soluble reaction products obtained were observed to be thermoplastic and could be melt processed at elevated temperatures. However, further reaction and crosslinking of these materials occurred during processing to produce thermosets, as demonstrated by rheological measurements and sintering experiments. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

On the mechanism of compatibilization of polyolefin/liquid crystalline polymer blends with graft copolymers

The compatibilization mechanism of some compatibilizers for blends of polyolefins with a liquid crystalline polymer (LCP) was studied. Polyethylene (PE) and polypropylene (PP) were blended with a semirigid LCP (SBH) in a batch mixer, either with and without compatibilizers. The latter were two commercially available samples of functionalized polyolefins, that is, a PE‐g‐MA (HDM) and a PP‐g‐AA (Polybond 1001) copolymer and some purposely synthesized PE‐g‐LCP and PP‐g‐LCP copolymers. Microtomed films of the binary and the ternary blends were annealed at 240°C on the hot stage of a polarizing microscope and the changes undergone by their morphology were recorded as a function of time. The results indicate that the compatibilizers lower the interfacial tension, thereby providing an improvement of the minor phase dispersion. In addition to this, the rate of the coalescence caused by the high‐temperature treatment is appreciably reduced in the systems compatibilized with the PE–SBH and PP–SBH graft copolymers. Among the commercial compatibilizers, only Polybond 1001 displayed an effect comparable to that of the above copolymers. HDM improved the morphology of the as‐prepared PE blends, but failed to grant sufficient morphological stabilization against annealing‐induced coarsening. The results are discussed with reference to the chemical structure of the different compatibilizers. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 3027–3034, 2000     

Compatibilization of nylon 6/liquid crystalline polymer blends with three types of compatibilizers

Polyblends of nylon 6 and liquid crystalline polymer (LCP) (Vectra A 950) are immiscible and highly incompatible, with resultant poor interfacial adhesion, large phase domains, and poor mechanical properties. In the present work, compatibilizing strategies are put forward for blends containing nylon and LCP. Effects of three types of compatibilizers, including ionomer Zn–sulfonated polystyrene (SPS), reactive copolymer styrene–maleic anhydride (SMA), functional grafted copolymers—polypropylene grafted glycidyl methacrylate (PP‐g‐GMA) and polypropylene grafted maleic anhydride (PP‐g‐MAH)—are studied in the aspects of morphology and dynamic mechanical behavior. The addition of compatibilizers decreases the domain size of the dispersed phase and results in improved interfacial adhesion between LCP and matrix. The compatibilization mechanism is discussed by way of diffuse reflectance Fourier transform spectroscopy (DRIFT), showing the reaction between compatibilizers and matrix nylon 6. Mechanical properties are improved by good interfacial adhesion. The contribution of SMA to mechanical properties is more obvious than that of Zn‐SPS and grafted PPs used. The blending procedure is correlated with the improvement of mechanical properties by the addition of compatibilizer. Two‐step blending is demonstrated as an optimum method to obtain composites with better mechanical properties as a result of a greater chance for LCP to contact the compatibilizer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1452–1461, 2003     

The effect of graft copolymers of maleic anhydride and epoxy resin on the mechanical properties and morphology of PP/ABS blends

In this work, maleic anhydride‐grafted polypropylene (PP‐g‐MAH) and maleic anhydride‐grafted poly(acrylonitrile‐butadiene‐styrene) (ABS‐g‐MAH) at 2 : 1 mass ratio were added as a compatibilizer in the PP/ABS blends. The compatibilizing effect was evaluated by adding the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ). The reaction in reactive extrusion, morphological structure, and properties of PP and ABS blends were investigated by using infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and X‐ray spectrum, transmission electron microscope (TEM), dynamic thermomechanical analysis (DMA), differential scanning calorimetry (DSC), and mechanical properties tests. The results showed that the compatibilizing effect was greatly improved because of the addition of the graft copolymers together with epoxy resin/imidazole curing agent (E51/2E4MZ) because the link structure of PP‐g‐MAH and ABS‐g‐MAH was formed by the reaction of anhydride group with epoxy group catalyzed by the imidazole. The size of the dispersed phase decreased dramatically, the interfacial adhesion between ABS particles and PP matrix was improved, and the tensile strength and flexural modulus of the PP/ABS blends increased further. The optimizing properties were obtained at 3 phr E51/2E4MZ. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40898.     

(EPDM/LLDPE)-g-MAH对回收光盘PC的增韧研究

采用自制的马来酸酐接枝三元乙丙橡胶/线形低密度聚乙烯共混物((EPDM/LLDPE)-g-MAH),通过熔融共混挤出对回收光盘聚碳酸酯(PC)进行增韧。结果表明,(EPDM/LLDPE)-g-MAH的加入有效地提高了回收光盘PC的拉伸强度和缺口冲击强度。当其加入量为5%时,共混物性能最优,拉伸强度和缺口冲击强度分别提高到原来的188%和276%。并用扫描电子显微镜对缺口冲击断面进行分析。     

Structure–microhardness correlation in blends of nylon 6/nylon 66 monofilaments

The microstructure (crystallinity, long spacing) and the micromechanical properties (microhardness H) of two series of nylon 6 and nylon 66 monofilaments and their blends were investigated as a function of annealing temperature T_A and uniaxial deformation in a wide composition range. In case of the homopolymers, the gradual rise of microhardness with T_A is interpreted in the light of the increasing values of the crystallinity α and the hardness of the crystals H_c. The depression of the hardness values of the blends from the additive behavior of the hardness of individual components is discussed in the basis of the crystallinity depression of one component by the second one and viceversa. Finally, the influence of drawing and pressing the blends at 130°C which leads to a hardness increase is also explained in the light of an increase in the H_c value of nylon 66 due to orientation. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 636–643, 2000     

Blends of nylon with polyethylene: Effect of compatibilization on mechanical and dynamic mechanical properties

Blends of Nylon 6 with very low density polyethylene (VLDPE) have been studied. The blends exhibit two phase morphology wherein VLDPE is dispersed in the form of spherical domains in Nylon 6 matrix. The water absorption of the blends decreased with increasing VLDPE content. The mechanical properties of these blends show loss in tensile and impact strength due to poor adhesion at the interface. Addition of a compatibilizer containing MAH groups was found to result in improved properties. The tensile strength increased significantly whereas impact testing showed no break confirming better stress transfer across the interface. The dynamic mechanical analysis showed presence of microheterogeneity resulting into merging of tan delta peaks as a result of compatibilization. The observed results are ascribed to the possible reaction between reactive groups in Nylon 6 and the compatibilizer leading to compatibilization through copolymer formation. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 161–168, 1998     

Effect of dynamic vulcanization on properties and morphology of nylon/SAN/NBR blends: A new compatibilization method of nylon/ABS blends

Dynamically vulcanized blends of nylon, styrene–acrylonitrile copolymer (SAN), and nitrile–butadiene rubber (NBR) were examined for mechanical properties, Shore D hardness, Vicat softening temperature, impact process, and phase morphology. The effect of a curing system such as phenolic formaldehyde resins (PF), dicumylperoxide (DCP), and a sulfur system on the mechanical properties of the nylon/SAN/NBR blends was studied, and dynamic vulcanization with a PF system was found to lead to outstanding toughness of the blends. The effect of PF content on the mechanical properties, Shore D hardness, and heat resistance of the nylon/SAN/NBR blends was also investigated. With increasing PF content the notched‐impact strength and Vicat softening temperature (VST) of the nylon/SAN/NBR (50/25/25) blends evidently improved, but tensile strength and Shore D hardness of the blends changed slightly. It can be concluded that the nylon/SAN/NBR (50/25/25) blends dynamically vulcanized by high‐content PF can attain excellent comprehensive mechanical properties, especially supertoughness, at room temperature. SEM was used to investigate the effect of dynamic vulcanization on disperse‐phase particle size, particle size distribution, and phase morphology. It was obvious that disperse‐phase particle size decreased with an increasing PF content. Thermal behavior and miscibility of dynamically vulcanized nylon/SAN/NBR with PF were investigated by DMTA. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2057–2062, 2003