Synthesis and characterization of polypropylene/clay nanocomposites

Polypropylene/clay (PP/clay) nanocomposites were synthesized via intercalative polymerization. The nanostructure of the composites was investigated by wide‐angle X‐ray diffractometry (WAXD) and transmission electron microscopy (TEM). The WAXD patterns of the PP/clay nanocomposites indicated that the characteristic diffraction peak of the clay disappeared. The TEM image showed the clay was exfoliated into nanometer size and dispersed uniformly in the PP matrix. The composites exhibited much higher storage modulus compared to that of pure PP. At temperatures higher than T_g, the storage modulus of the PP/clay nanocomposites with 8.1 wt % clay content increased three times that of the pure PP. Additionally, the thermal stability of the nanocomposites significantly increased. The maximum decomposition temperature was increased by 44°C with the introduction of about 10 wt % clay. The heat‐distortion temperatures (HDTs) of the nanocomposites also increased. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3611–3617, 2001     

The effect of crystallization on the structure and morphology of polypropylene/clay nanocomposites

The effect of crystallization on the structure and morphology of maleic anhydride grafted polypropylene (PP‐MA)/clay (montmorillonite) nanocomposites (PPCNs) is presented. Wide‐angle X‐ray diffraction (WAXD) measurements of PPCNs crystallized at different temperatures show that the extent of intercalation increases with the crystallization temperature. The enhancement of intercalation occurs with lower clay content PPCNs, and maximum intercalation takes place for 4 wt% clay content. The mechanism of intercalation has been proposed through crystallization. Excess γ‐form of the crystallite of PP‐MA appears in presence of clay, possibly because of the confinement of the polymer chain between the clay particles. WAXD data also reveals that d‐spacing increases gradually with clay content. The decrease of spherulitic size is observed with increasing clay content, which indicates that clay particles act as nucleating agents. Lamellar textures have been explored by using small angle X‐ray scattering (SAXS) and transmission electron microscopy (TEM), which exhibit that both the lamellar thickness and long period of the PPCNs are higher than those of PP‐MA.     

Preparation and characterization of EVA/clay Nanocomposites with improved barrier performance

Poly (ethylene‐co‐vinyl acetate) (EVA)/clay nanocomposites containing two different organoclays with different clay loadings were prepared. The transport of gases (oxygen and nitrogen) through the composite membranes was investigated and the results were compared. These studies revealed that the incorporation of nanoclays in the polymer increased the efficiency of the membranes toward barrier properties. It was also found that the barrier properties of the membranes decreased with clay loadings. This is mainly due to the aggregation of clay at higher loadings. The morphology of the nanocomposites was studied by scanning electron microscopy, transmission electron microscopy and X‐ray scattering. Small angle X‐ray scattering results showed significant intercalation of the polymer chains between the organo‐modified silicate layers in all cases. Better dispersed silicate layer stacking and more homogeneous membranes were obtained for Cloisite® 25A based nanocomposites compared with Cloisite® 20A samples. Microscopic observations (SEM and TEM) were coherent with those results. The dispersion of clay platelets seemed to be maximized for 3 wt % of clay and agglomeration increased with higher clay loading. Wide angle X‐ray scattering results showed no significant modifications in the crystalline structure of the EVA matrix because of the presence of the clays. The effect of free volume on the transport behavior was studied using positron annihilation spectroscopy. The permeability results have been correlated with various permeation models. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of clay on mechanical and gas barrier properties of blown film LDPE/clay nanocomposites

Low density polyethylene (LDPE)/clay nanocomposites, which can be used in packaging industries, were prepared by melt‐mix organoclay with polymer matrix (LDPE) and compatibilizer, polyethylene grafted maleic anhydride (PEMA). The pristine clay was first modified with alkylammonium salt surfactant, before melt‐mixed in twin screw extruder attached to blown‐film set. D‐spacing of clay and thermal behavior of nanocomposites were characterized by Wide‐Angle X‐ray Diffraction (WAXD) and differential scanning calorimetry (DSC), respectively. WAXD pattern confirmed the increase in PEMA contents exhibited better dispersion of clay in nanocomposites. Moreover, DSC was reported the increased PEMA contents caused the decrease in degree of crystallinity. Mechanical properties of blown film specimens were tested in two directions of tensile tests: in transverse tests (TD tests) and in machine direction tests (MD tests). Tensile modulus and tensile strength at yield were improved when clay contents increased because of the reinforcing behavior of clay on both TD and MD tests. Tensile modulus of 7 wt % of clay in nanocomposite was 100% increasing from neat LDPE in TD tests and 17% increasing in MD tests. However, elongation at yield decreased when increased in clay loading. Oxygen permeability tests of LDPE/clay nanocomposites also decreased by 24% as the clay content increased to 7 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of clay content on the melting behavior and crystal structure of nonisothermal crystallized poly(L‐lactic acid)/nanocomposites

To study the effect of organophilic clay concentration on nonisothermal crystallization, poly(L ‐lactic acid) (PLLA)/montmorillonite (MMT) nanocomposites were prepared by mixing various amounts of commercial MMT (Cloisite^® 30B) and PLLA. The effect of MMT content on melting behavior and crystal structure of nonisothermal crystallized PLLA/MMT nanocomposites was investigated by differential scanning calorimetry (DSC), small‐angle X‐ray scattering, and wide‐angle X‐ray diffraction (XRD) analyses. The study was focused on the effect of the filler concentration on thermal and structural properties of the nonisothermally crystallized nanocomposite PLLA/MMT. The results obtained have shown that at filler loadings higher than 3 wt %, intercalation of the clay is observed. At lower clay concentrations (1–3 wt %), exfoliation predominates. DSC and XRD analysis data show that the crystallinity of PLLA/MMT composites increases drastically at high clay loadings (5–9 wt %). In these nanocomposites, PLLA crystallizes nonisothermally in an orthorhombic crystal structure, assigned to the α form of PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synergistic effect of organoclay fillers based on fluorinated surfmers for preparation of polystyrene nanocomposites

Novel fluorinated reactive surfactants were used for the organic modification of monmorillonite clays. These organoclays were used for the preparation of polystyrene?clay nanocomposites by in‐situ free radical polymerization. Reference systems based on hydrocarbon homologous surfmer and nonpolymerizable surfactants were also used to deduce the effect of the fluorine moiety and the polymerizable function on the morphology and thermal stability of the prepared nanocomposites. Different structural parameters of the surfactants were investigated and modulated for the clay modification including: the nature of surfactant (surfmer/classical surfactant, fluorinated, or hydrocarbonated), the length of the fluorinated chain as well as the length of the hydrocarbon spacers linking the ammonium head to the fluorine chain or the polymerizable acrylic function. Wide angle‐X‐ray scattering (WAXD), thermogravimetric analysis (TGA), and electronic microcopies (TEM and SEM) were used to establish a structure‐morphology, thermal properties relationships, and to highlight the key parameters governing the exfoliation process. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42347.     

Strain‐induced crystallization behavior of phenolic resin crosslinked natural rubber/clay nanocomposites

Nanocomposites of natural rubber (NR) and unmodified clay were prepared by latex compounding method. Phenolic resin (PhOH) was used to crosslink NR. Crosslinked neat NR was also prepared for comparison. The structure–property relationship of uncrosslinked and crosslinked NR/clay nanocomposites was examined to verify the reinforcement mechanism. Microstructure of NR/clay nanocomposites was studied by using transmission electron microscopic (TEM), X‐ray diffraction (XRD), wide angle X‐ray diffraction (WAXD), and small angle X‐ray scattering (SAXS) analyses. The results showed the evidence of intercalated clay together with clay tactoids for the nanocomposite samples. The highest tensile strength was achieved for the crosslinked NR/clay nanocomposite. The onset strain of deformation induced the crystallization of NR for nanocomposites was found at almost the same strain, and furthermore their crystallization was developed at lower strain than that of the crosslinked neat NR because of the clay orientation and alignment. However, at high strain region, the collaborative crystallization process related to the clay dispersion and conventional crosslink points in the NR was responsible to considerably high tensile strength of the crosslinked NR/clay nanocomposite. Based on these analyses, a mechanistic model for the strain‐induced crystallization and orientational evolution of a network structure of PhOH‐crosslinked NR/clay nanocomposite was proposed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42580.     

Melt processing and characterization of polypropylene/pristine montmorillonite nanocomposite: Influence of compatibilizer and hyperbranched polymer

In the present investigation, nanocomposites of polypropylene (PP)‐montmorillonite (MMT) clay were prepared by a single‐step compounding method to study the influence of hyperbranched polyester (HBPE) on rheological and mechanical properties of PP composites in the presence of a compatibilizer. In service of this objective, polyvinylchloride‐grafted‐maleic anhydride (PP‐g‐MA) was used as a compatibilizer for hydrophobic PP and hydrophilic clay. Rheological property in terms of melt viscosity was examined by a Brabender torque rheometer. The composite's morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), whereas the dispersion state of nanoparticles in the PP matrix was studied by X‐ray diffraction (XRD). The thermal behavior of nanocomposites was examined by differential scanning calorimetry (DSC). The analysis of results confirmed that the interactions among both additives significantly influenced the morphology, rheology, and thermomechanical properties of the nanocomposites. J. VINYL ADDIT. TECHNOL., 22:72–79, 2016. © 2014 Society of Plastics Engineers     

Effect of melt processing conditions on the morphology and properties of nylon 6 nanocomposites

Nylon 6 (PA‐6) organoclay nanocomposites were prepared by melt processing using three different twin screw extruders (TSEs). The effect of mixing conditions, feed port location, residence time, and number of extrusion passes on the morphology and mechanical properties of the nanocomposites were examined. Wide‐angle X‐ray scattering, transmission electron microscopy (TEM), and mechanical property data are reported. Particle analyses were performed on the TEM images to quantitatively characterize the extent of exfoliation. The amount of shear and the mixing conditions created by TSEs have a significant effect on the morphology and properties of PA‐6 nanocomposites. Morphology and mechanical property results show that (1) melting the polymer before coming into contact with the organoclay followed by a low level of shear and (2) maintaining a medium level of shear throughout the extruder with a longer residence time lead to extremely high platelet dispersion and matrix reinforcement for PA‐6 nanocomposites. Nanocomposites formed in a DSM microcompounder showed similar morphologies and modulus trends as those obtained with conventional TSEs; thus, this microcompounder is a good alternative for nanocomposite research especially when only small amounts of material are available. POLYM. ENG. SCI., 47:1847–1864, 2007. © 2007 Society of Plastics Engineers     

Polymer‐Clay Nanocomposites Based on Blends of Polyamide‐6 and Polyethylene

The preparation of polyamide‐6/clay, high‐density polyethylene/clay, and high‐density polyethylene/ polyamide‐6/clay nanocomposites is considered. X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and Fourier Transform Infrared (FTIR) measurements show that the clay enhances the crystallization of the γ‐form of polyamide‐6. The clay also acts as a nucleation agent and causes a reduction of spherulitte size. Scanning electron microscopy (SEM) analysis of fracture surfaces shows that the clay reduces the PA‐6 particle size in the HDPE/PA‐6/clay nanocomposites and changes the morphology. Mechanical properties and the effect of maleated polyethylene are also reported.     

Polymorphic behavior of nylon 6/saponite and nylon 6/montmorillonite nanocomposites

X‐ray diffraction methods and DSC thermal analysis have been used to investigate the structural change of nylon 6/clay nanocomposites. Nylon 6/clay has prepared by the intercalation of ε‐caprolactam and then exfoliaton of the layered saponite or montmorillonite by subsequent polymerization. Both X‐ray diffraction data and DSC results indicate the presence of polymorphism in nylon 6 and in nylon 6/clay nanocomposites. This polymorphic behavior is dependent on the cooling rate of nylon 6/clay nanocomposites from melt and the content of saponite or montmorillonite in nylon 6/clay nanocomposites. The quenching from the melt induces the crystallization into the γ crystalline form. The addition of clay increases the crystallization rate of the α crystalline form at lower saponite content and promotes the heterophase nucleation of γ crystalline form at higher saponite or montmorillonite content. The effect of thermal treatment on the crystalline structure of nylon 6/clay nanocomposites in the range between Tg and Tm is also discussed.     

Miscibility and Crystallization Behaviors of Polyamide 6/Polytetrafluoroethylene Blends

Summary: The miscibility and crystallization behaviors of polyamide 6 (PA 6)/polytetrafluoroethylene (PTFE) blends, prepared via reactive extrusion, are systematically investigated by means of wide‐angle X‐ray diffraction (WAXD), differential scanning calorimetry (DSC), and dynamic mechanical thermal analysis (DMTA). WAXD measurements show that no co‐crystallization occurred between two components, while DSC and DMTA measurements suggest that a certain degree of miscibility between them might exist due to the formation of some copolymers during the reactive extrusion.

DMTA curves for the pure PA 6 sample and PA 6/PTFE blends with various compositions.     

Structure,morphology, and biodegradability of poly(ε‐caprolactone)‐based nanocomposites

Biodegradable polycaprolactone/organoclay nanocomposites were prepared by solvent casting, using different amounts of filler and matrices differing by average molecular weight. Intercalated nanocomposites were obtained. The nanocomposites were characterized by wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS) methods. Negligible variations in the degree of crystallinity were detected by WAXD. The thickness of crystalline lamellae, measured by SAXS, increased in low molecular weight polymer nanocomposites with increasing clay amount; this effect was weakened in matrices with high molecular weight. Differential scanning calorimetry showed an inhibiting effect of clay on crystallization. The composites' ductility was largely increased, whereas stiffness was retained. After biodegradation in compost, in all samples, the degree of crystallinity was increased, meaning that the less ordered portion of the sample was preferentially degraded. Clay slowed down the biodegradation rate, coherently with the observed increase in the lamellar thickness due to the filler. This may offer a strategy for tuning the biodegradability by calibrating their semicrystalline framework. POLYM. ENG. SCI., 2011. ©2011 Society of Plastics Engineers.     

Effect of electrospun fibers of polyhydroxybutyrate filled with different organoclays on morphology,biodegradation, and thermal stability of poly(ε‐caprolattone)

The properties of nanocomposites of poly(ε‐caprolattone) (PCL) were studied, the pristine PCL was implemented with the introduction of electrospun fibers of polyhydroxybutyrate (PHB), containing a cationic (Cloisite) or an anionic (Perkalite) clay. These multicomponent composites containing a very low amount of clay confined in fibers are different from usual nanocomposite materials containing clay dispersed in the polymer matrix, which are produced by solvent casting or melt extrusion. To analyze the influence of the different fillers on the final composite, a preliminary study on PHB cast films and fibers prepared from the same solution was carried out, and then a thorough analysis was accomplished of the behavior of these particular nanocomposites PCL/PHB fibers/clay to elucidate the effects of the filled electrospun fibers on the PCL matrix. The structure and morphology of the samples were characterized by wide‐angle X‐ray diffraction and small angle X‐ray scattering; differential scanning calorimetry and thermogravimetric analysis were used to understand the influence of the fillers on the thermal behavior and stability; mechanical properties were evaluated and biodegradation studies were carried out. The PHB electrospun fibers and the fractured surface of the final composites were examined by scanning electron microscopy. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42342.     

Interfacial interactions and performance of polyamide 6/modified attapulgite clay nanocomposites

Attapulgite (AT) clay was firstly treated with sodium polyacrylate (PAS), then polyamide 6 (PA6)/AT nanocomposites were prepared by simple melt compounding. Transmission electron microscope (TEM) and Fourier transform infrared spectrometry (FT‐IR) of treated AT confirm the success of purifying and surface modification of the original AT by PAS. X‐ray diffraction spectra for the nanocomposites show that the microstructure of AT in PA6 matrix is almost unchanged. It indicates that a strong interfacial adhesion exists between AT and PA6 matrix through analyzing fracture surfaces of the nanocomposites, the variation of glass transition temperature (T_g) obtained by dynamic mechanical analysis, and interfacial interaction factors; field emission scanning electron microscopy on the fracture surfaces of the nanocomposites shows that a uniform dispersion of AT is obtained. The above two aspects conform to the improvement of mechanical and thermal properties of the nanocomposites. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Clay intercalation and influence on flammability and crystallization behaviors of POE‐based nanocomposites

Ethylene‐octene copolymer (POE)‐based nanocomposites were prepared from POE or maleic anhydride grafted POE with organo‐modified montmorillonite (OMT) using melt blending technique. Their morphology, flammability, and crystallization behavior were investigated by X‐ray diffraction (XRD), transmission electron microscopy (TEM), cone calorimeter, and differential scanning calorimetry (DSC). XRD and TEM studies confirmed the intercalation of clay layers within the POE matrix whereas the exfoliation throughout the maleated POE matrix. Cone calorimetry results exhibited that the reduction in heat release rate of exfoliated maleated‐POE/OMT nanocomposite was greater than that of intercalated POE/OMT nanocomposite. The DSC results suggested that the nonisothermal kinetics crystallization of the exfoliated nanocomposite corresponded to tridimensional growth with heterogeneous nucleation. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Morphology and properties of nanocomposites from organoclays with reduced cation exchange capacity

Organoclays with different levels of reduction in the original cation exchange capacity (CEC) were prepared to characterize the morphology and Young's modulus of their melt‐processed nanocomposites made from nylon 6 (PA‐6) and polypropylene/polypropylene grafted with maleic anhydride (PP/PP‐g‐MA). Wide‐angle X‐ray scattering (WAXS), transmission electron microscopy (TEM), and Young's modulus data are reported. Three different levels of CEC reduction were obtained; WAXS analysis and percentage loss on ignition (LOI) calculations for these organoclays showed a reduction in both the intergallery spacing and in the amount of organic modifier contained in the clay with CEC reduction. The morphology and modulus results show that these reduced‐CEC organoclays led to lower exfoliation and modulus enhancement for both PA‐6 and PP/PP‐g‐MA nanocomposites. The results may be influenced by differences in layer charge and charge distribution that could have been produced during the charge reduction process. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Epoxy‐clay nanocomposites: Influence of the clay surface modification on structure

In this article, the effect of four different clay surface modifiers on the structure of epoxy‐clay nanocomposites was studied. Various organoclays were prepared via cation exchange reaction between inorganic cations naturally occuring in the clay gallery and different alkylammonium ions. Epoxy‐clay nanocomposites were prepared by in situ intercalative polymerization using a hardener of polyoxypropylenediamine type. It was found that various clay surface modifiers exhibit different catalytic effect on curing of epoxy inside the clay gallery as observed by measuring of the gel time with dynamic mechanical analysis. This was confirmed by monitoring the change in the d‐spacing by wide angle X‐ray scattering performed in situ during curing. Morphology of the cured systems was probed by transmission electron microscopy (TEM) and wide angle X‐ray scattering (WAXS). The degree of dispersion observed by TEM and WAXS corresponds with achieved mechanical properties of cured composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Phenolic resin‐crosslinked natural rubber/clay nanocomposites: Influence of clay loading and interfacial adhesion on strain‐induced crystallization behavior

Nanocomposites of natural rubber (NR) and pristine clay (clay) were prepared by latex mixing, then crosslinked with phenolic resin (PhOH). For comparative study, the PhOH‐crosslinked neat NR was also prepared. Influence of clay loading (i.e., 1, 3, 5, and 10 phr) on mechanical properties and structural change of PhOH‐crosslinked NR/clay nanocomposites was studied through X‐ray diffraction (XRD), transmission electron microscopic (TEM), wide‐angle X‐ray diffraction (WAXD), tensile property measurement, and Fourier transform infrared spectroscopy (FTIR). XRD and TEM showed that the clay was partly intercalated and aggregated, and that the dispersion state of clay was non‐uniform at higher clay loading (>5 phr). From tensile test measurement, it was found that the pronounced upturn of tensile stress was observed when the clay loading was increased and a maximum tensile strength of the PhOH‐crosslinked NR/clay nanocomposites was obtained at 5 phr clay. WAXD observations showed that an increased addition of clay induced more orientation and alignment of NR chains, thereby lowering onset strain of strain‐induced crystallization and promoting crystallinity of the NR matrix during tensile deformation. FTIR investigation indicated a strong interfacial adhesion between NR matrix and clay filler through a phenolic resin bridge. This suggested that the PhOH did not only act as curative agent for crosslinking of NR, but it also worked as coupling agent for promoting interfacial reaction between NR and clay. The presence of strong interfacial adhesion was found to play an important role in the crystallization process, leading to promotion of mechanical properties of the PhOH‐crosslinked NR/clay nanocomposites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43214.