Kinetics of the propylene polymerization with prepolymerization at high temperature using Ziegler‐Natta catalyst

The bulk polymerization of propylene in liquid monomers with Ziegler‐Natta catalyst at 95°C is studied, using alkyl aluminum as the cocatalyst and dicyclopentyldimethoxysilane as the external donor. The highest catalyst activity is shown at the cocatalyst/Ti molar ratio of 300, which keeps relatively constant with the molar ratio increasing from 300 to 800. Besides, the catalyst activity is up to 65 kgPP/(gCat*h) in the range of cocatalyst/donor molar ratio from 12 to 16. The polymerization reaction rate curves with and without catalyst precontacting are similar, while the activity with catalyst precontacting are higher than that without precontacting. Furthermore, the kinetics of polymerization with and without prepolymerization are investigated in the range of the polymerization temperature from 70 to 95°C. It shows that at the high temperature, the polymerization rate increases with prepolymerization. Finally, the influence of prepolymerization at 95°C on the polymerization kinetics and particle properties is also described. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41816.     

Ti-Mg催化剂的预聚合及其对乙烯气相聚合的影响

研究了用镁粉研制的Ti-Mg系乙烯气相聚合催化剂在各种条件下的预聚合反应,以及各种类型AlR_3对预聚合反应的影响。考察了AlR_3/Ti摩尔比、催化剂浓度、预聚合反应速度对预聚合产物的影响及预聚物的气相聚合反应。比较了经预聚合与不经预聚合催化剂气相聚合与淤浆聚合动力学行为及聚合反应结果。用扫描电镜(SEM)观察了催化剂、预聚物、聚合产物的颗粒形态,研究了催化剂粒子生成预聚物粒子再聚合成为产物粒子的聚合过程。     

Prepolymerization of ethylene with a Ziegler–Natta catalyst

The slurry prepolymerization of ethylene using TiCl₄/MgCl₂ as a catalyst was investigated. A 2³‐factorial experimental design method was employed to study the effects of the temperature, hydrogen, and active cocatalyst‐to‐catalyst molar ratio (Al/Ti) on the catalyst activity, prepolymer melt flow index, and powder bulk density. All dependent variables increased when the active Al/Ti ratio increased from 1 to 2. The hydrogen–Al/Ti interaction had a significant effect on the prepolymer melt flow index and catalyst activity. The hydrogen (partial pressure ranging from 0.5 to 1.5 bar) and temperature (ranging from 60 to 80°C) variables as well as the hydrogen–temperature and hydrogen–temperature–Al/Ti interactions increased the prepolymer powder bulk density, which ranged from 0.11 to 0.373 g/cc. To find the reason for the prepolymer powder bulk density variation with the operating conditions, the particle size distribution and crystallinity of the prepolymers were determined. The increasing catalyst activity, ranging from 132 to 660 g of polyethylene/mmol of Ti, enhanced the weight percentage of fines, which ranged from 3 to 60, and decreased the average particle size, which ranged from 562 to 120 μm. This was the reason for the increasing prepolymer powder bulk density and could be due to the breakup of the prepolymer particles during prepolymerization. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Polymerization of liquid propylene with a fourth‐generation Ziegler–Natta catalyst: Influence of temperature,hydrogen, monomer concentration,and prepolymerization method on powder morphology

Liquid propylene was polymerized in a 5‐L autoclave batch reactor using a commercially available TiCl₄/MgCl₂/Al(ethyl)₃/DCPDMS Ziegler–Natta catalyst, with a phthalate ester as internal electron donor. The powders from these polymerizations were characterized using laser diffraction particle size distribution (PSD) analysis, scanning electron microscopy (SEM), and bulk density measurements. These characteristics were analyzed as a function of the process conditions, including hydrogen and monomer concentration, polymerization temperature, and the prepolymerization method. It was shown that polymerization temperature influences the powder morphology to a large extent. At low temperatures, high‐density particles were obtained, showing regular shaped particle surfaces and low porosities. With increasing temperature, the morphology gradually was transferred into a more open structure, with irregular surfaces and poor replication of the shape of the catalyst particle. When using a prepolymerization step at a relatively low temperature, the morphology obtained was determined by this prepolymerization step and was independent from conditions in main polymerization. The morphology obtained was the same as that observed after a full polymerization at temperature. Even when using a short polymerization at an increasing temperature, the morphology was strongly influenced by the initial conditions. The effect of variation in hydrogen concentration supported the conclusion that the initial polymerization rate determines the powder morphology. In the absence of hydrogen, high bulk densities, and regularly shaped particles were obtained, even at high temperatures. With increasing hydrogen concentration, the reaction rates increased rapidly, and with that changed the morphology. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1421–1435, 2003     

Study on propylene polymerization in the presence of phenolic antioxidant (Irganox 1076) and characterization of stabilized polymers

The aim of this study was to investigate different concentrations of Irganox 1076 on Ziegler–Natta catalyst performance during propylene polymerization. Antioxidant masking was conducted by addition of different molar ratio of triethylaluminum (TEAL). Proton nuclear magnetic resonance and Fourier transform infrared spectroscopy spectra confirmed the complete conversion of antioxidant to aluminum aryloxide form. The different concentrations of masked antioxidant with different molar ratio of TEAL were used during polymerization and the catalyst activity was evaluated. Morphology, particle size distribution, melt temperature, crystallization temperature, degree of crystallinity, oxidative induction time, and isotacticity of products in the presence of masked antioxidant were evaluated. Results showed that incomplete masking of OH phenolic antioxidant led to significant catalyst activity reduction. J. VINYL ADDIT. TECHNOL., 21:285–289, 2015. © 2014 Society of Plastics Engineers     

聚丙烯细粉产生的原因及影响

结合CS－2型高效催化剂在液相本体法聚丙烯装置应用的实际，分析了细粉含量增加的主要原因有：催化剂本身粒径的分布，催化剂钛含量，铝／钛（摩尔比，下同）控制情况，预聚效果以及聚合反应条件的影响。通过对细粉增加原因的分析，提出了3条改进措施：改进催化剂制备，选择粒径分布好，强度高的催化剂载体，控制好制备的各个环节；调整预聚操作条件，保证预聚效果，减少催化剂破损；根据催化剂特性，控制好催化剂的铝／钛，充分利用催化剂活性是减少细粉生成的有效措施。     

Highly active Ziegler–Natta catalyst for propylene polymerization

Polymerization of propylene was carried out by using a MgCl₂–EtOH–TiCl₄–ID–TEA–ED catalyst system in n‐heptane, where ID (internal donor) was an organic diester, ED (external donor) was a silane compound, and TEA (triethyl aluminum) was the activator. The influences of temperature, pressure, time, hydrogen, and the molar ratios of Al/Ti and ED/Ti on polymer isotacticity and catalyst activity were studied by solubility in boiling n‐heptane and measuring the polymer produced, respectively. The morphology of the polymers was evaluated through scanning electron microscopy and particle size distribution. The rheological properties of the poly(propylene) were determined by the melt flow index. It was found that the catalyst showed good morphology and high activity and also the produced polymers were characterized by high isotacticity and globulelike shapes. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1744–1749, 2005     

Nature of activating effect of two‐step polymerization of propylene

The prepolymerization effect on propylene polymerization in the presence of a TiCl₃‐based catalyst, modified by di‐n‐buthyl ether, was studied. The influence of prepolymerization on the electron spin resonance spectra and morphology of the catalyst, as well as the properties and the morphology of both prepolymer and regular polymerization products, was investigated. The polymer morphology was evaluated through scanning electron microscopy, polymer bulk density, and particle size distribution. Some evidence of the enhancement effect of prepolymerization on the catalyst activity and stereospecificity was obtained. No influence from prepolymerization was observed on molecular weight and its distribution, melting point, and crystallinity of polypropylene. These findings, when discussed in connection with the morphology results of the catalyst and prepolymer, showed that the prepolymerization performed at mild reaction conditions prevents fast and extensive “fragmentation” of the original catalyst agglomerates. The more controlled breakup of the catalyst particles in the course of slowed growth of prepolymer exposes the occluded catalyst fragments with uniform size and prevents their reagglomeration. Resulting from the above, catalyst homogeneity, catalyst activity, and polymer morphology are improved. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 353–359, 1999     

助催化剂对BCZ-108催化剂聚合行为的影响研究

在铝钛物质的量比为25、50、100、150、200、300条件下,研究丙烯聚合用BCZ-108催化剂的聚合行为及聚丙烯的主要性能,并与常规应用的NA催化剂进行对比。结果表明,随着铝钛物质的量比的增大,两种催化剂的聚合反应速率的衰减越来越快,聚丙烯的立体定向性越来越低,熔点越来越低,分子量分布越来越宽;BCZ-108催化剂的聚合活性比NA催化剂高30%以上;两种催化剂的聚合活性在铝钛物质的量比为50时达到最高,此时BCZ-108催化剂的活性为1 212 g·g^-1,NA催化剂的活性为907 g·g^-1。     

Porous versus novel compact Ziegler–Natta catalyst particles and their fragmentation during the early stages of bulk propylene polymerization

The effect of the porosity of Ziegler–Natta catalyst particles on early fragmentation, nascent polymer morphology, and activity were studied. The bulk polymerization of propylene was carried out with three different heterogeneous Ziegler–Natta catalysts under industrial conditions at low temperatures, that is, with a novel self‐supported catalyst (A), a SiO₂‐supported catalyst (B), and a MgCl₂‐supported catalyst (C), with triethyl aluminum as a cocatalyst and dicyclopentyl dimethoxy silane as an external donor. The compact catalyst A exhibited no measurable porosity and a very low surface area (<5 m²/g) by Brunauer–Emmet–Teller analysis, whereas catalysts B and C showed surface areas of 63 and 250 m²/g, respectively. The surface and cross‐sectional morphologies of the resulting polymer particles at different stages of particle growth were analyzed by scanning electron microscopy and transmission electron microscopy. The compact catalyst A showed homogeneous and instantaneous fragmentation already in the very early stages of polymerization, which is typically observed for porous MgCl₂‐supported Ziegler–Natta catalysts. Moreover, the compact catalyst particles gave rise to almost perfectly spherical polymer particles with a smooth surface. In contrast, the silica‐supported catalyst B gave rise to particles having a cauliflower morphology, and the second reference catalyst C produced fairly spherical polymer particles with a rough surface. All of the three catalysts exhibited similar activities of 450 g of polypropylene/g of catalyst after 30 min of polymerization, and most interestingly, the comparative kinetic data presented indicated that the reaction rates were not influenced by the porosity of the catalyst. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008.     

Propylene polymerization using MgCl2/ethylbenzoate/TiCl4 catalyst: Determination of titanium oxidation states

The chemical interaction of the catalyst MgCl₂/ethylbenzoate/TiCl₄ with the cocatalysts triethylaluminum and trisobutylaluminum was investigated to establish a relationship between the titanium oxidation states and the catalytic activity, polymer isotacticity, and polymer molecular weight in propylene polymerizations. This interaction was studied using different Al : Ti molar ratios by measuring the changes of the titanium oxidation states at different polymerization times. Both hydrogen and alkyl aluminum caused a reduction of Ti⁴⁺ species to lower oxidation states species Ti³⁺ and Ti²⁺. However, the Ti⁴⁺ species reduction appeared to be incomplete. It was found that the Ti⁴⁺ species undergoes a severe reduction as the Al : Ti molar ratio increases from 50 to 230 as overreduction takes place. This change of the Ti³⁺ species percentage with time was found to correlate with the rate–time profiles of propylene polymerization. From this observation, it would be fair to conclude that the trivalent titanium species is more likely to be the active titanium species for propylene polymerization than the aforementioned catalyst system. On the other hand, hydrogen addition was found to cause an increase in Ti³⁺ species. The increases in both hydrogen amount and/or Al : Ti molar ratio were found to cause a decrease in both molecular weight and polypropylene isotactic index. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 56–62, 2004     

丙烯淤浆预聚合对聚丙烯产品性能的影响

研究了丙烯淤浆预聚合对聚丙烯（PP）性能的影响，试验过程中采用Ziegler-Natta催化剂，并使用三乙基铝作为助催化剂。结果表明，与不预聚相比，经过预聚PP的等规度、结晶度、熔点、结晶温度都有所提高，但熔体流动速率下降。预聚时加入外给电子体。可以提高PP的熔点和结晶度。在铝钛物质的量比为3／1～10／1范围内增加预聚合过程中的烷基铝用量。也可以提高PP的熔点和结晶度。提高预聚合温度。PP的结晶温度不下降。     

A stacked neural network approach for yield prediction of propylene polymerization

Prediction of reaction yield as the most important characteristic process of a slurry polymerization industrial process of propylene has been carried out. Stacked neural network as an effective method for modeling of inherently complex and nonlinear systems–especially a system with a limited number of experimental data points–was chosen for yield prediction. Also, effect of operational parameters on propylene polymerization yield was modeled by the use of this method. The catalyst system was Mg(OEt)₂/DIBP/TiCl₄/PTES/AlEt₃, where Mg(OEt)₂, DIBP (diisobutyl phthalate), TiCl₄, PTES (phenyl triethoxy silane), and triethyl aluminum (AlEt₃) (TEAl) were employed as support, internal electron donor (ID), catalyst precursor, external electron donor (ED), and co‐catalyst, respectively. The experimental results confirmed the validity of the proposed model. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Polymerization of propylene using MgCl2 (ethoxide type)/TiCl4/diether heterogeneous Ziegler–Natta catalyst

Heterogeneous Ziegler–Natta catalyst of MgCl₂ (ethoxide type)/TiCl₄/diether was prepared. 2,2‐Diisobutyl‐1,3‐dimethoxy propane (DiBDMP), diether, was used as internal donor. Slurry polymerization of propylene was carried out using the catalyst in dry heptane while triethylaluminium (TEA) was used as co‐catalyst. The co‐catalyst effects, such as catalyst molar ratio, polymerization temperature, H₂ pressure, external donor, triisobutylaluminium (TiBA) and monomer pressure, on the activity of the catalyst and isotacticity index (II) of the polymers obtained were studied. Rate of polymerization versus polymerization time is of a decay type with no acceleration period. There are an optimum Al/Ti molar ratio and temperature to obtain the highest activity of the catalyst. The maximum activity was obtained at 60 °C. Increasing the monomer pressure to 1 010 000 Pa linearly increased the activity of the catalyst. Addition of hydrogen to 151 500 Pa pressure increased activity of the catalyst from 2.25 to 5.45 kg polypropylene (PP) (g cat)^?1 h^?1 using 505 000 Pa pressure of monomer. The II decreased with increasing Al/Ti ratio, monomer pressure, hydrogen pressure and increased with increasing temperature to 60 °C, following with decrease as the temperature increases. Productivity of 11.55 kg (PP) (g cat)^?1 h^?1 was obtained at 1 010 000 Pa pressure of monomer and temperature of 60 °C. Addition of methyl p‐toluate (MPT) and dimethoxymethyl cyclohexyl silane (DMMCHS) as external donors decreased the activity of the catalyst sharply, while the II slightly increased. Some studies of the catalyst structure and morphology of the polymer were carried out using FTIR, X‐ray fluorescence, scanning electron microscopy and Brunauer–Emmett–Teller techniques. Copyright © 2005 Society of Chemical Industry     

Effect of prepolymerization on propylene polymerization

Polymerization of propylene was performed using MgCl₂. EtOH.TiCl₄.ID.TEA.ED catalyst system in hexane, where internal donor (ID) was an organic diester and external donor (ED) was a silane compound and also triethyl aluminum (TEA) as activator. A new method called isothermal/nonisothermal method (INM), a combination of isothermal and nonisothermal methods, was applied to produce the spherical polymer particles. The effects of the INM method and prepolymerization temperature on the final polymer morphology, M_w, and catalyst activity were also investigated. The morphology of the polymers was evaluated through scanning electron microscopy (SEM) images. GPC results were used for molecular weight (M_w) evaluation. It was found that the polymers had a better morphology when they were prepared using INM method. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Polymerization of propylene using the high‐activity Ziegler–Natta catalyst system SiO2/MgCl2 (ethoxide type)/TiCl4/Di‐n‐butyl phthalate/triethylaluminum/dimethoxy methyl cyclohexyl silane

The bisupported Ziegler–Natta catalyst system SiO₂/MgCl₂ (ethoxide type)/TiCl₄/di‐n‐butyl phthalate/triethylaluminum (TEA)/dimethoxy methyl cyclohexyl silane (DMMCHS) was prepared. TEA and di‐n‐butyl phthalate were used as a cocatalyst and an internal donor, respectively. DMMCHS was used as an external donor. The slurry polymerization of propylene was studied with the catalyst system in n‐heptane from 45 to 70°C. The effects of the TEA and H₂ concentrations, temperature, and monomer pressure on the polymerization were investigated. The optimum productivity was obtained at [Al]/[DMMCHS]/[Ti] = 61.7:6.2:1 (mol/mol/mol). The highest activity of the catalyst was obtained at 60°C. Increasing the H₂ concentration to 100 mL/L increased the productivity of the catalyst, but a further increase in H₂ reduced the activity of the catalyst. Increasing the propylene pressure from 1 to 7 bar significantly increased the polymer yield. The isotacticity index (II) decreased with increasing TEA, but the H₂ concentration, temperature, and monomer pressure did not have a significant effect on the II value. The viscosity‐average molecular weight decreased with increasing temperature and with the addition of H₂. Three catalysts with different Mg/Si molar ratios were studied under the optimum conditions. The catalyst with a Mg/Si molar ratio of approximately 0.93 showed the highest activity. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1177–1181, 2003     

Effect of diether as internal donor on MgCl2‐supported Ziegler–Natta catalyst for propylene polymerization

This article demonstrates the influence of the molar ratio between diether as internal donor and Magnesium dichloride in processing of the catalyst preparation on the catalytic performance for propylene polymerization with MgCl₂‐supported Ziegler–Natta catalyst. The effect of electron donor on catalyst is investigated. The experimental data find that diether content on catalyst increases and Ti content on catalyst decreases with the increase of diether/Mg molar ratio. This result indicates that diether as internal donor is not coordinated to Ti species but to Mg species on catalyst. The introduction of diether remarkably improves the catalytic activity. The extents of improvement closely connect with diether/Mg molar ratio. The stereospecificity of catalyst intensively depends on the structure of diether as internal donor. The possible model of multi‐active sites on heterogeneous Ziegler–Natta catalyst is proposed to explain these phenomena. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1399–1404, 2006     

Millimeter‐size polyethylene hollow spheres synthesized with MgCl2‐supported Ziegler‐Natta catalyst

Polyethylene hollow spheres with diameters of 0.4–2 mm were synthesized by a two‐step slurry polymerization in a single reactor with a spherical MgCl₂‐supported Ziegler‐Natta catalyst activated by triethylaluminum, in which the first step was prepolymerization with 0.1 MPa propylene and the second step was ethylene polymerization under 0.6 MPa. The prepolymerization step was found necessary for the formation of hollow spherical particles with regular shape (perfectly spherical shape). The effects of adding small amount of propylene (propylene/ethylene < 0.1 mol/mol) in the reactor after the prepolymerization step were investigated. Average size of the polymer particles was increased, and the polymerization rate was markedly enhanced by the added propylene. Development of the particle morphology with polymerization time was also studied. The polymer particles formed by less than 20 min of ethylene polymerization showed hollow spherical morphology with thin shell layer. Most of the particles had ratio of shell thickness/particle radius smaller than 0.5. By prolonging the ethylene polymerization, the shell thickness/particle radius ratio gradually approached 1, and the central void tended to disappear. Central void in polymer particles formed from smaller catalyst particles disappeared after shorter time of polymerization than those formed from bigger catalyst particles. The shell layer of the hollow particles contained large number of macro‐, meso‐ and micro‐pores. The mesopore size distributions of four typical samples were analyzed by nitrogen adsorption–desorption experiments. A simplified multigrain model was proposed to explain the morphogenesis of the hollow spherical particles. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43207.     

Bulk polymerization of vinyl chloride with half-titanocene/MAO catalyst

Bulk polymerization of vinyl chloride (VC) with Cp^∗Ti(OPh)₃/MAO catalyst was investigated. The bulk polymerization of VC with Cp^∗Ti(OPh)₃/MAO catalyst proceeded to give poly(vinyl chloride) (PVC) with high molecular weight in good yields. The M_n of the polymer increased in direct proportion to polymer yields and the line passed through the origin. The M_w/M_n of the polymer decreased with an increase of polymer yield. The GPC elution curves were unimodal and the whole curves shifted clearly to the higher molecular weight as a function of reaction time. This indicates that the control of molecular weight can be achieved in the polymerization of VC with Cp^∗Ti(OPh)₃/MAO catalyst even in bulk. The structure of PVC obtained from the bulk polymerization of VC with Cp^∗Ti(OPh)₃/MAO catalyst consists of a regular structure. The thermal stability of the polymer obtained with Cp^∗Ti(OPh)/MAO catalyst was higher than that of PVC obtained from radical polymerization and depended on the molecular weight of the polymer. In contrast to that, the initial decomposition temperature of the polymer obtained from a radical polymerization did not depend on the molecular weight. We presumed that the decomposition of the polymer obtained with Cp^∗Ti(OPh)₃/MAO catalyst initiated at the chain end.     

Effects of aluminum alkyls on ethylene/1‐hexene polymerization with supported metallocene/MAO catalysts in the gas phase

The effects of aluminum alkyls on the gas‐phase ethylene homopolymerization and ethylene/1‐hexene copolymerization over polymer‐supported metallocene/methylaluminoxane [(n‐BuCp)₂ZrCl₂/MAO] catalysts were investigated. Results with triisobutyl aluminum (TIBA), triethyl aluminum (TEA), and tri‐n‐octyl aluminum (TNOA) showed that both the type and the amount of aluminum alkyl influenced the polymerization activity profiles and to a lesser extent the polymer molar masses. The response to aluminum alkyls depended on the morphology and the Al : Zr ratio of the catalyst. Addition of TIBA and TEA to supported catalysts with Al : Zr >200 reduced the initial activity but at times resulted in higher average activities due to broadening of the kinetic profiles, i.e., alkyls can be used to control the shape of the activity profiles. A catalyst with Al : Zr = 110 exhibited relatively low activity when the amount of TIBA added was <0.4 mmol, but the activity increased fivefold by increasing the TIBA amount to 0.6 mmol. The effectiveness of the aluminum alkyls in inhibiting the initial polymerization activity is in the following order: TEA > TIBA >> TNOA. A 2‐L semibatch reactor, typically run at 80°C and 1.4 MPa ethylene pressure for 1 to 5 h was used for the gas‐phase polymerization. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3549–3560, 2004