Ni/Al_2O_3催化剂的CO_2-TPD表征

Ni/Al_2O_3催化剂是甲烷二氧化碳重整反应制取合成气研究最多、最具应用潜力的一种催化剂。通过对催化剂进行CO_2-TPD研究,考察还原态Ni/Al_2O_3催化剂的CO_2脱附特性。结果表明,浸渍法制备的Ni/Al_2O_3催化剂CO_2脱附曲线呈现双峰,分别在(60~65)℃和(350~380)℃出现高低温两个活性位;高温CO_2吸附量为3.0 cm~3·g~(-1),低温CO_2吸附量为24.0 cm~3·g~(-1)。催化剂的CO_2吸附量与其Ni含量无关。考察选用不同载体的CO_2脱附行为,发现以Al_2O_3为载体的催化剂CO_2吸附量是MgO和SiO_2为载体催化剂的2~4倍,以TiO_2为载体的催化剂几乎不吸附CO_2。     

Carbon formation and its influence on ethanol steam reforming over Ni/Al2O3 catalysts

Ethanol steam reforming was studied over Ni/Al₂O₃ catalysts. The effect of support (- and γ-Al₂O₃), metal loading and a comparison between conventional H₂ reduction with an activation method employing a CH₄/O₂ mixture was investigated. The properties of catalysts were studied by N₂ physisorption, X-ray diffraction (XRD) and temperature programmed reduction (TPR). After activity tests, the catalysts were analyzed by scanning electron microscopy (SEM) and thermogravimetric analysis (TG/DTA). Ni supported on γ-Al₂O₃ was more active for H₂ production than the catalyst supported on -Al₂O₃. Metal loading did not affect the catalytic performance. The alternative activation method with CH₄/O₂ mixture affected differently the activity and stability of the Ni/γ-Al₂O₃ and the Ni/-Al₂O₃ catalyst. This activation method increased significantly the stability of Ni/-Al₂O₃ compared to H₂ reduction. SEM and TG/DTA analysis indicate the formation of filamentous carbon during the CH₄/O₂ activation step, which is associated with the increasing catalyst activity and stability. The effect of temperature on the type of carbon formed was investigated; indicating that filamentous coke increased activity while encapsulating coke promoted deactivation. A discussion about carbon formation and the influence on the activity is presented.     

Synthesis and properties of PdO/CeO2-Al2O3 catalysts for methane combustion

This study focuses on the loading of catalytic materials, e.g., palladium on the surface of supporting materials, with the aim to obtain catalysts with high activity for methane combustion. The catalyst PdO/CeO₂-Al₂O₃ was prepared by impregnation under ultrasonic condition. The effect of different activation methods on the activity of catalysts for methane catalytic combustion was tested. The properties of reaction and adsorption of oxygen species on catalyst surface were characterized by H₂-temperature programmed reduction (H₂-TPR), and O₂-temperature programmed desorption (O₂-TPD). Furthermore, the sulfur tolerance and sulfur poisoning mode were investigated. The results indicate that the catalyst PdO/CeO₂-Al₂O₃ activated with rapid activation shows higher activity for methane combustion and better sulfur tolerance. The result of sulfur content analysis shows that there is a large number of sulfur species on the catalyst’s surface after reactivation at high temperature. It proves that the activity of catalysts cannot be fully restored by high-temperature reactivation.     

K-, CeO2-, and Mn-promoted Ni/Al2O3 catalysts for stable CO2 reforming of methane

Reforming of methane with carbon dioxide into syngas over Ni/γ-Al₂O₃ catalysts modified by potassium, MnO and CeO₂ was studied. The catalysts were prepared by impregnation technique and were characterized by N₂ adsorption/desorption isotherm, BET surface area, pore volume, and BJH pore size distribution measurements, and by X-ray diffraction and scanning electron microscopy. The performance of these catalysts was evaluated by conducting the reforming reaction in a fixed bed reactor. The coke content of the catalysts was determined by oxidation conducted in a thermo-gravimetric analyzer. Incorporation of potassium and CeO₂ (or MnO) onto the catalyst significantly reduced the coke formation without significantly affecting the methane conversion and hydrogen yield. The stability and the lower amount of coking on promoted catalysts were attributed to partial coverage of the surface of nickel by patches of promoters and to their increased CO₂ adsorption, forming a surface reactive carbonate species. Addition of CeO₂ or MnO reduced the particle size of nickel, thus increasing Ni dispersion. For Ni–K/CeO₂–Al₂O₃ catalysts, the improved stability was further attributed to the oxidative properties of CeO₂. Results of the investigation suggest that stable Ni/Al₂O₃ catalysts for the carbon dioxide reforming of methane can be prepared by addition of both potassium and CeO₂ (or MnO) as promoters.     

Tri-reforming of methane: a novel concept for catalytic production of industrially useful synthesis gas with desired H2/CO ratios

A novel process concept called tri-reforming of methane has been proposed in our laboratory using CO₂ in the flue gases from fossil fuel-based power plants without CO₂ separation [C. Song, Chemical Innovation 31 (2001) 21–26]. The proposed tri-reforming process is a synergetic combination of CO₂ reforming, steam reforming, and partial oxidation of methane in a single reactor for effective production of industrially useful synthesis gas (syngas). Both experimental testing and computational analysis show that tri-reforming can not only produce synthesis gas (CO + H₂) with desired H₂/CO ratios (1.5–2.0), but also could eliminate carbon formation which is usually a serious problem in the CO₂ reforming of methane. These two advantages have been demonstrated by tri-reforming of CH₄ in a fixed-bed flow reactor at 850 °C with supported nickel catalysts. Over 95% CH₄ conversion and about 80% CO₂ conversion can be achieved in tri-reforming over Ni catalysts supported on an oxide substrate. The type and nature of catalysts have a significant impact on CO₂ conversion in the presence of H₂O and O₂ in tri-reforming in the temperature range of 700–850 °C. Among all the catalysts tested for tri-reforming, their ability to enhance the conversion of CO₂ follows the order of Ni/MgO > Ni/MgO/CeZrO > Ni/CeO₂ ≈ Ni/ZrO₂ ≈ Ni/Al₂O₃ > Ni/CeZrO. The higher CO₂ conversion over Ni/MgO and Ni/MgO/CeZrO in tri-reforming may be related to the interaction of CO₂ with MgO and more interface between Ni and MgO resulting from the formation of NiO/MgO solid solution. Results of catalytic performance tests over Ni/MgO/CeZrO catalysts at 850 °C and 1 atm with different feed compositions confirm the predicted equilibrium conversions based on the thermodynamic analysis for tri-reforming of methane. Kinetics of tri-reforming were also examined. The reaction orders with respect to partial pressures of CO₂ and H₂O are different over Ni/MgO, Ni/MgO/CeZrO, and Ni/Al₂O₃ catalysts for tri-reforming.     

Effects of small MoO3 additions on the properties of nickel catalysts for the steam reforming of hydrocarbons III. Reduction of Ni-Mo/Al2O3 catalysts

Ni/Al₂O₃ catalyst modified by small amounts of Mo show unusual properties in the steam reforming of hydrocarbons. There are no data about the effect of small amounts of molybdenum on reduction of the Ni-Mo supported catalysts. The properties of these very complex systems depend on the conditions of successive preparation stages (calcination, reduction) or the process conditions.

A series of Ni/Al₂O₃ catalysts modified by Mo were prepared in order to investigate the influence of promoter amounts and preparation sequence on their properties. Temperature programmed reduction (TPR) has been employed to study the reducibility of Ni-Mo/Al₂O₃ catalysts. Catalysts were further characterized by BET area, H₂ chemisorption and X-ray diffraction measurements.

The TPR curves of Ni-Mo/Al₂O₃ catalysts are very complex. Mo addition leads to the decrease of catalysts reducibility. However, complete reduction of NiO and MoO₃ can be achieved at 800 °C. The reduction course depends on the sequence of nickel and molybdenum addition into the support. Precise measurements of Ni peaks positions in the XRD pattern of Ni/Al₂O₃ and Ni-Mo/Al₂O₃ samples show the possibility of Ni-Mo solid solution formation.     

Lean reduction of NO by C3H6 over Ag/alumina derived from Al2O3, AlOOH and Al(OH)3

The effectiveness of Ag/Al₂O₃ catalyst depends greatly on the alumina source used for preparation. A series of alumina-supported catalysts derived from AlOOH, Al₂O₃, and Al(OH)₃ was studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), ultraviolet–visible (UV–vis) spectroscopy, diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy, O₂, NO + O₂-temperature programmed desorption (TPD), H₂-temperature programmed reduction (TPR), thermal gravimetric analysis (TGA) and activity test, with a focus on the correlation between their redox properties and catalytic behavior towards C₃H₆-selective catalytic reduction (SCR) of NO reaction. The best SCR activity along with a moderated C₃H₆ conversion was achieved over Ag/Al₂O₃ (I) employing AlOOH source. The high density of Ag–O–Al species in Ag/Al₂O₃ (I) is deemed to be crucial for NO selective reduction into N₂. By contrast, a high C₃H₆ conversion simultaneously with a moderate N₂ yield was observed over Ag/Al₂O₃ (II) prepared from a γ-Al₂O₃ source. The larger particles of Ag_mO (m > 2) crystallites were believed to facilitate the propene oxidation therefore leading to a scarcity of reductant for SCR of NO. An amorphous Ag/Al₂O₃ (III) was obtained via employing a Al(OH)₃ source and 500 °C calcination exhibiting a poor SCR performance similar to that for Ag-free Al₂O₃ (I). A subsequent calcination of Ag/Al₂O₃ (III) at 800 °C led to the generation of Ag/Al₂O₃ (IV) catalyst yielding a significant enhancement in both N₂ yield and C₃H₆ conversion, which was attributed to the appearance of γ-phase structure and an increase in surface area. Further thermo treatment at 950 °C for the preparation of Ag/Al₂O₃ (V) accelerated the sintering of Ag clusters resulting in a severe unselective combustion, which competes with SCR of NO reaction. In view of the transient studies, the redox properties of the prepared catalysts were investigated showing an oxidation capability of Ag/Al₂O₃ (II and V) > Ag/Al₂O₃ (IV) > Ag/Al₂O₃ (I) > Ag/Al₂O₃ (III) and Al₂O₃ (I). The formation of nitrate species is an important step for the deNO_x process, which can be promoted by increasing O₂ feed concentration as evidenced by NO + O₂-TPD study for Ag/Al₂O₃ (I), achieving a better catalytic performance.     

Structure and reactivity of plasma treated Ni/Al2O3 catalyst for CO2 reforming of methane

The glow discharge plasma treated Ni/Al₂O₃ catalyst showed an excellent anti-coke property for CO₂ reforming of methane. Characterizations using X-ray powder diffraction (XRD), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction (TPR), transmission electron microscopy (TEM), and CO adsorbed infrared spectroscopy (IR) were conducted to investigate the structure and reactivity of the plasma treated Ni/Al₂O₃ catalyst for CO₂ reforming of methane. It confirms that the plasma treatment of Ni precursor at room temperature followed by calcination thermally has a significant influence on the surface characteristics of the active phase. The plasma treated catalyst contains high concentration of close packed plane with improved Ni dispersion and enhanced Ni-alumina interaction, which lead to high catalytic activity and excellent resistance to formations of filamentous carbon and encapsulating carbon.     

Reforming of methane and coalbed methane over nanocomposite Ni/ZrO2 catalyst

Nanocomposite Ni/ZrO₂-AN catalyst consisting of comparably sized Ni metal and ZrO₂ nanoparticles is studied in comparison with zirconia- and alumina-supported Ni catalysts (Ni/ZrO₂-CP and commercial Ni/Al₂O₃-C) for steam reforming of methane (SRM) and for combined steam and CO₂ reforming of methane (CSCRM). The reactions are performed under atmospheric pressure with stoichiometric amounts of H₂O and CH₄ or (H₂O + CO₂) and CH₄ at 1073 K. Under a wide range of methane space velocity (gas hourly space velocity of methane GHSV_CH4 = 12,000–96,000 ml/(h g_cat.), the nanocomposite Ni/ZrO₂-AN catalyst always shows higher activity and stability for both SRM and CSCRM reactions. The two supported Ni catalysts (Ni/ZrO₂-CP and Ni/Al₂O₃-C) exhibit fairly stable catalysis under low GHSV_CH4 but they are easily deactivated under high GHSV_CH4 and become completely inactive when they are reacted for ca.100 h at GHSV_CH4 = 48,000 ml/(h g_cat.). The CSCRM reaction is carried out with different H₂O/CO₂ ratios in the reaction feed while keeping the molar ratio (H₂O + CO₂)/CH₄ = 1.0, the results prove that the nanocomposite Ni/ZrO₂-AN catalyst can be highly promising in enabling a catalytic technology for the production of syngas with flexible H₂/CO ratios (ca. H₂/CO = 1.0–3.0) to meet the requirements of various downstream chemical syntheses.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

MnOx/Pt/Al2O3 catalysts for CO oxidation in H2-rich streams

The catalytic activity of Pt on alumina catalysts, with and without MnO_x incorporated to the catalyst formulation, for CO oxidation in H₂-free as well as in H₂-rich stream (PROX) has been studied in the temperature range of 25–250 °C. The effect of catalyst preparation (by successive impregnation or by co-impregnation of Mn and Pt) and Mn content in the catalyst performance has been studied. A low Mn content (2 wt.%) has been found not to improve the catalyst activity compared to the base catalyst. However, catalysts prepared by successive impregnation with 8 and 15 wt.% Mn have shown a lower operation temperature for maximum CO conversion than the base catalyst with an enhanced catalyst activity at low temperatures with respect to Pt/Al₂O₃. A maximum CO conversion of 89.8%, with selectivity of 44.9% and CO yield of 40.3% could be reached over a catalyst with 15 wt.% Mn operating at 139 °C and λ = 2. The effect of the presence of 5 vol.% CO₂ and 5 vol.% H₂O in the feedstream on catalysts performance has also been studied and discussed. The presence of CO₂ in the feedstream enhances the catalytic performance of all the studied catalysts at high temperature, whereas the presence of steam inhibits catalysts with higher MnO_x content.     

Design of a novel bifunctional catalyst IrFe/Al2O3 for preferential CO oxidation

In this study, a novel bifunctional catalyst IrFe/Al₂O₃, which is very active and selective for preferential oxidation of CO under H₂-rich atmosphere, has been developed. When the molar ratio of Fe/Ir was 5/1, the IrFe/Al₂O₃ catalyst performed best, with CO conversion of 68% and oxygen selectivity towards CO₂ formation of 86.8% attained at 100 °C. It has also been found that the impregnation sequence of Ir and Fe species on the Al₂O₃ support had a remarkable effect on the catalytic performance; the activity decreased following the order of IrFe/Al₂O₃ > co-IrFe/Al₂O₃ > FeIr/Al₂O₃. The three catalysts were characterized by XRD, H₂-TPR, FT-IR and microcalorimetry. The results demonstrated that when Ir was supported on the pre-formed Fe/Al₂O₃, the resulting structure (IrFe/Al₂O₃) allowed more metallic Ir sites exposed on the surface and accessible for CO adsorption, while did not interfere with the O₂ activation on the FeO_x species. Thus, a bifunctional catalytic mechanism has been proposed where CO adsorbed on Ir sites and O₂ adsorbed on FeO_x sites; the reaction may take place at the interface of Ir and FeO_x or via a spill-over process.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

碱/碱土金属修饰Ni基催化剂的CO2吸附与甲烷化性能

采用分步浸渍法制备了碱/碱土金属修饰Ni基催化剂Ni-M/Al₂O₃ (M=K₂CO₃, Na₂CO₃, MgO, CaO)。探究了碱/碱土金属的添加对改性Ni基催化剂CO₂吸附和甲烷化性能的影响。研究发现,碱/碱土金属的添加提高了Ni/Al₂O₃催化剂表面的碱性活性位点密度,强化了其CO₂吸附性能。碱/碱土金属类型影响Ni-M/Al₂O₃催化剂碱性活性位点的分布、NiO物相的转化及Ni的分散度,进而影响其甲烷化性能。MgO添加使NiO物相转化为与载体呈强相互作用的β型和γ型NiO,降低了催化剂表面的强碱性活性位点比例,有利于CO₂吸附活化。Ni-MgO/Al₂O₃的CO₂吸附容量最高为0.68mmolCO₂/g,其CO₂转化率和CH₄选择性分别高达58.4%和95.4%,其在烟气CO₂捕集与原位甲烷化中极具应用前景。     

助剂Ba对Pd/Al_2O_3和Pt/Al_2O_3催化剂的C1-C3烷烃催化燃烧性能的影响

通过浸渍法制备了Al_2O_3负载的Pd和Pt催化剂,考察催化剂的甲烷、乙烷和丙烷催化燃烧活性,以及助剂Ba对催化性能的影响。对于Pd/Al_2O_3催化剂,加入Ba使活性物种PdO颗粒变大和还原温度升高,形成更稳定的PdO活性物种,是Pd-Ba/Al_2O_3催化剂活性提升的主要原因。对于Pt/Al_2O_3催化剂,加入Ba助剂使活性物种Pt0含量降低,PtO_x与Al_2O_3载体相互作用增强,使PtO_x物种更难被还原为Pt~0,导致Pt-Ba/Al_2O_3催化剂活性降低。Pd和Pt催化剂催化烷烃氧化反应活性规律一致:丙烷乙烷甲烷。Pd/Al_2O_3催化剂有利于C—H键活化,Pt/Al_2O_3催化剂有利于C—C键活化。Pt/Al_2O_3催化剂对C1-C3烷烃氧化活性的差别明显大于Pd/Al_2O_3催化剂。Pt/Al_2O_3催化剂对碳比例高的烷烃活性更高。     

Performance of catalytic reactors for the hydrogenation of CO2 to hydrocarbons

Fluidized bed and slurry reactors were employed to increase the CO₂ conversion and desirable product selectivity in the direct hydrogenation of CO₂ to hydrocarbons over K-promoted iron catalysts, as it is beneficial for the removal of heat generated due to highly exothermic nature of the reaction. The iron catalysts (Fe-K/Al₂O₃ and Fe-Cu-Al-K) were characterized by BET surface area, CO₂ and H₂ chemisorption, temperature-programmed reduction (TPR), X-ray diffraction (XRD) and temperature-programmed hydrogenation (TPH). The results of TPR and TPH study clearly indicated that co-precipitated Fe-Cu-Al-K catalyst has much higher reducibility and catalytic activity of CO₂ hydrogenation at low temperature than Fe-K/Al₂O₃. The performance of fluidized bed or slurry reactors was superior to that of fixed bed reactor for the CO₂ hydrogenation over Fe-Cu-Al-K catalyst in terms of CO₂ conversion and hydrocarbon productivity. Moreover, light olefins and heavy hydrocarbons were selectively synthesized in fluidized bed and slurry reactors, respectively. The optimum operation conditions and the effects of operating variables on the CO₂ conversion and its product distribution in these catalytic reactors were also discussed.     

Control of the product ratio of CO2/(CO+CO2) and inhibition of catalyst deactivation for steam reforming of gasoline to produce hydrogen

Factors controlling the product ratio of CO₂/(CO+CO₂) and methods for inhibiting deactivation of catalyst for steam reforming of gasoline were studied. Syngas (H₂+CO) as major product was produced on Ni-Mo/Al₂O₃ and the major product on Ni-Re/Al₂O₃ was H₂ and CO₂ at the same reaction conditions. Hydrogen with a high CO₂/(CO+CO₂) ratio of about 92% was produced by coupling reaction of steam reforming and water gas shift on Ni-Re/Al₂O₃ catalyst at 805 K. The multifunctional activity of the bimetallic catalyst of Ni-Re/Al₂O₃ and the suitable reaction temperature were of crucial significance for the coupling reaction. Although no deactivation could be observed on both Ni-Mo/Al₂O₃ and Ni-Re/Al₂O₃ catalysts for steam reforming of sulfur-free fuels in about 200 h of time on stream, the activity and sulfur-tolerance of Ni-Re/Al₂O₃ was much better than the values of Ni-Mo/Al₂O₃ for steam reforming of sulfur-containing fuels because of the unique role of rhenium in the Ni-Re catalyst. The unique role of rhenium in Ni-Re catalyst was mainly because of alloying of rhenium with nickel to form bimetallic Ni-Re sites and interaction of rhenium with sulfur to form S-Re binds. The sulfur-tolerance of Ni-Re/Al₂O₃ for steam reforming of sulfur-containing gasoline was improved further by addition of a small amount of ZSM-5. The activity and sulfur-tolerance of Ni-Mo/Al₂O₃ was also enhanced by the addition of ZSM-5.     

Characterizations and activities of the nano-sized Ni/Al2O3 and Ni/La–Al2O3 catalysts for NH3 decomposition

A series of nano-sized Ni/Al₂O₃ and Ni/La–Al₂O₃ catalysts that possess high activities for NH₃ decomposition have been successfully synthesized by a coprecipitation method. The catalytic performance was investigated under the atmospheric conditions and a significant enhancement in the activity after the introduction of La was observed. Aiming to study the influence of La promoter on the physicochemical properties, we characterized the catalysts by N₂ adsorption/desorption, XRD, H₂-TPR, chemisorption and TEM techniques. Physisorption results suggested a high specific surface area and XRD spectra showed that nickel particles are in a highly dispersed state. A combination of XRD, TEM and chemisorption showed that Ni⁰ particles with the average size lower than 5.0 nm are always obtained even though the Ni loading ranged widely from 4 to 63%. Compared with the Ni/Al₂O₃ catalysts, the Ni/La–Al₂O₃ ones with an appropriate amount of promoter enjoy a more open mesoporous structure and higher dispersion of Ni. Reduction kinetic studies of prepared catalysts were investigated by temperature-programmed reduction (TPR) method and the fact that La additive partially destroyed the metastable Ni–Al mixed oxide phase was detailed.     

过渡金属Ni对Pd/Al_2O_3催化剂甲烷催化燃烧性能的影响

考察过渡金属Ni对Pd/Al_2O_3催化剂甲烷催化燃烧活性的影响以及过渡金属负载量及循环条件对甲烷降解性能的影响,采用扫描电镜、N_2吸附-脱附以及H_2程序升温还原技术对催化剂进行表征。结果表明,过渡金属Ni的添加对催化剂在(375~475)℃下的甲烷催化燃烧活性产生影响。催化剂经多次重复使用后,催化燃烧活性提高。分析原因为经过渡金属Ni改性后,可与载体形成NiAl_2O_4尖晶石,促进活性组分形成较小晶粒,并改善活性组分分散度,提高催化剂催化活性。     

Quantified NOx adsorption on Pt/K/gamma-Al2O3 and the effects of CO2 and H2O

A multi-component NO_x-trap catalyst consisting of Pt and K supported on γ-Al₂O₃ was studied at 250 °C to determine the roles of the individual catalyst components, to identify the adsorbing species during the lean capture cycle, and to assess the effects of H₂O and CO₂ on NO_x storage. The Al₂O₃ support was shown to have NO_x trapping capability with and without Pt present (at 250 °C Pt/Al₂O₃ adsorbs 2.3 μmols NO_x/m²). NO_x is primarily trapped on Al₂O₃ in the form of nitrates with monodentate, chelating and bridged forms apparent in Diffuse Reflectance mid-Infrared Fourier Transform Spectroscopy (DRIFTS) analysis. The addition of K to the catalyst increases the adsorption capacity to 6.2 μmols NO_x/m², and the primary storage form on K is a free nitrate ion. Quantitative DRIFTS analysis shows that 12% of the nitrates on a Pt/K/Al₂O₃ catalyst are coordinated on the Al₂O₃ support at saturation.

When 5% CO₂ was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by 45% after 1 h on stream due to the competition of adsorbed free nitrates with carboxylates for adsorption sites. When 5% H₂O was included in a feed stream with 300 ppm NO and 12% O₂, the amount of K-based nitrate storage decreased by only 16% after 1 h, but the Al₂O₃-based nitrates decreased by 92%. Interestingly, with both 5% CO₂ and 5% H₂O in the feed, the total storage only decreased by 11%, as the hydroxyl groups generated on Al₂O₃ destabilized the K–CO₂ bond; specifically, H₂O mitigates the NO_x storage capacity losses associated with carboxylate competition.