Production of hydrogen by steam reforming of bio-oil over Ni/Al2O3 catalysts: Effect of addition of promoter and preparation procedure

Catalytic steam reforming of bio-oil was investigated in a fixed bed tubular reactor for production of hydrogen. Two series of nickel/alumina (Ni/Al₂O₃) supported catalysts promoted with ruthenium (Ru) and magnesium (Mg) were prepared. Each catalyst of the first series (Ru–Ni/Al₂O₃) was prepared by co-impregnation of nickel and ruthenium on alumina. They were examined to investigate the effect of adding ruthenium on the performance of the catalysts for hydrogen production. The effect of the temperature, the most effective parameter in the steam reforming of bio-oil, on the activity of the catalysts was also investigated. Each catalyst of the second series (Ni–MgO/Al₂O₃) was prepared by consecutive impregnation using various preparation procedures. They were tested to determine the effect of adding magnesium as well as the effect of the preparation procedure on the outlet gas concentrations. It was shown that in both series, the catalysts were more efficient in hydrogen production as well as carbon conversion than Ni/Al₂O₃ catalysts. The highest hydrogen yield was 85% which was achieved over Ru–Ni/Al₂O₃ at 950 °C. It was also found that the effect of adding a small amount of ruthenium was superior to that of nickel on the yield of hydrogen when the nickel content was equal to or greater than 10.7%.     

Characterization of Sn doped Ni/Al2O3 steam reforming catalysts by XPS

XPS measurements have shown that tin oxides are more readily reduced to metallic tin by hydrogen in Ni/Al₂O₃ systems than on pure Al₂O₃. During the reductive activation of Sn doped Ni/Al₂O₃ catalysts, surface segregation of the dopant was observed. This finding may explain that tin enhances the selectivity of the steam reforming catalysts only when added in very low concentrations and that it acts as a poison at higher loadings.     

Stable carbon dioxide reforming of methane over modified Ni/Al2O3 catalysts

CO₂ reforming of methane was studied over modified Ni/Al₂O₃ catalysts. The metal modifiers were Co, Cu, Zr, Mn, Mo, Ti, Ag and Sn. Relative to unmodified Ni/Al₂O₃, catalysts modified with Co, Cu and Zr showed slightly improved activity, while other promoters reduced the activity of CO₂ reforming. Mn-promoted catalyst showed a remarkable reduction in coke deposition, while entailing only a small reduction in catalytic activity compared to unmodified catalyst. The catalysts prepared at high calcination temperatures showed higher activity than those prepared at low calcination temperature. The Mn-promoted catalyst showed very low coke deposition even in the absence of diluent gas and the activity changed only slightly during 100 h operation. This revised version was published online in July 2006 with corrections to the Cover Date.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Synergetic effect of combined use of Cu–ZnO–Al2O3 and Pt–Al2O3 for the steam reforming of methanol

Commercial Cu–ZnO–Al₂O₃ catalysts are used widely for steam reforming of methanol. However, the reforming reactions should be modified to avoid fuel cell catalyst poisoning originated from carbon monoxide. The modification was implemented by mixing the Cu–ZnO–Al₂O₃ catalyst with Pt–Al₂O₃ catalyst. The Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture created a synergetic effect because the methanol decomposition and the water–gas shift reactions occurred simultaneously over nearby Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalysts in the mixture. A methanol conversion of 96.4% was obtained and carbon monoxide was not detected from the reforming reaction when the Pt–Al₂O₃ and Cu–ZnO–Al₂O₃ catalyst mixture was used.     

Influence of preparation method on performance of Cu(Zn)(Zr)-alumina catalysts for the hydrogen production via steam reforming of methanol

The selective production of hydrogen via steam reforming of methanol (SRM) was performed using prepared catalysts at atmospheric pressure over a temperature range 200–260^∘C. Reverse water gas shift reaction and methanol decomposition reactions also take place simultaneously with the steam reforming reaction producing carbon monoxide which is highly poisonous to the platinum anode of PEM fuel cell, therefore the detailed study of effect of catalyst preparation method and of different promoters on SRM has been carried out for the minimization of carbon monoxide formation and maximization of hydrogen production. Wet impregnation and co-precipitation methods have been comparatively examined for the preparation of precursors to Cu(Zn)(Al₂O₃) and Cu(Zn)(Zr)(Al₂O₃). The catalyst preparation method affected the methanol conversion, hydrogen yield and carbon monoxide formation significantly. Incorporation of zirconia in Cu(Zn)(Al₂O₃) catalyst enhanced the catalytic activity, hydrogen selectivity and also lower the CO formation. Catalyst Cu(Zn)(Zr)(Al₂O₃) with composition Cu/Zn/Zr/Al:12/4/4/80 prepared by co-precipitation method was the most active catalyst giving methanol conversion up to 97% and CO concentration up to 400 ppm. Catalysts were characterized by atomic absorption spectroscopy (AAS), Brunauer-Emett-Teller (BET) surface area, pore volume, pore size and X-ray powder diffraction (XRPD). The XRPD patterns revealed that the addition of zirconia improves the dispersion of copper which resulted in the better catalytic performance of Cu(Zn)(Zr)(Al₂O₃). The time-on-stream (TOS) catalysts stability test was also conducted for which the Cu(Zn)(Zr)(Al₂O₃) catalyst gave the consistent performance for a long time compared to other catalysts.     

Partial oxidation of methane over ruthenium catalysts

The catalytic partial oxidation of methane with oxygen to produce synthesis gas was studied under a wide range of conditions over supported ruthenium catalysts. The microreador results demonstrated the high activity of ruthenium catalysts for this reaction. A catalyst having as little as 0.015% (w/w) Ru on Al₂O₃ gave a higher synthesis gas selectivity than a catalyst having 5% Ni on SiO₂. XANES measurements for fresh and used catalyst samples confirmed that ruthenium is reduced from ruthenium dioxide to ruthenium metal early during the experiments. Ruthenium metal is thus the active element for the methane partial oxidation reaction.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

Steam reforming of LPG over Ni and Rh supported on Gd-CeO2 and Al2O3: Effect of support and feed composition

The steam reforming of liquefied petroleum gas (LPG) over Ni- and Rh-based catalysts supported on Gd-CeO₂ (CGO) and Al₂O₃ was studied at 750-900 °C. The order of activity was found to be Rh/CGO > Ni/CGO ∼ Rh/Al₂O₃ > Ni/Al₂O₃; we indicated that the comparable activity of Ni/CGO to precious metal Rh/Al₂O₃ is due to the occurring of gas-solid reactions between hydrocarbons and lattice oxygen () on CGO surface along with the reaction taking place on the active site of Ni, which helps preventing the carbon deposition and promoting the steam reforming of LPG.The effects of O₂ (as oxidative steam reforming) and H₂ adding were further studied over Ni/CGO and Ni/Al₂O₃. It was found that the additional of these compounds significantly reduced the amount of carbon deposition and promoted the conversion of hydrocarbons (i.e., LPG as well as CH₄, C₂H₄ and C₂H₆ occurred from the thermal decomposition of LPG) to CO and H₂. Nevertheless, the addition of too high O₂ oppositely decreased H₂ yield due to the oxidizing of Ni particle and the possible combusting of H₂ generated from the reaction, while the addition of too high H₂ also negatively affect the catalyst activity due to the occurring of catalyst active site competition and the inhibition of gas-solid reactions between the gaseous hydrocarbon compounds and on the surface of CGO (for the case of Ni/CGO).     

A crucial role of O2 and O2 on mayenite structure for biomass tar steam reforming over Ni/Ca12Al14O33

Newly synthesized nickel calcium aluminum catalysts (Ni/Ca₁₂Al₁₄O₃₃) were tested in a fixed bed reactor for biomass tar steam reforming, toluene as tar destruction model compound. Four catalysts (Ni/Ca₁₂Al₁₄O₃₃) were prepared with Ni loading amount from 1, 3, 5 to 7 wt%, even 1% loading catalyst also showed excellent performance. Catalysts aged experiments in the absence (60 h on stream) and presence of H₂S were characterized by BET, X-ray diffraction (XRD), and Raman spectra. It was observed that Ni/Ca₁₂Al₁₄O₃₃ showed excellent sustainability against coke formation due to the “free oxygen” in the catalysts. It also exhibited higher H₂S-poisoning resistance property compared to the commercial catalysts Ni/Al₂O₃ (5%) and Ni/CaO_0.5/MgO_0.5. Raman spectra revealed that “free oxygen O₂⁻ and O₂²⁻” in the structure of the catalysts could be substituted by sulfur then protected Ni poisoning on some degree, but reactivation experiments by O₂ flowing showed that the sulfide Ni/Ca₁₂Al₁₄O₃₃ was difficult to completely restore, incorporation of sulfur in the structure only partly regain by O₂. The kinetic model proposes, as generally accepted, a first-order reaction for toluene with activation energy of 82.06 kJ mol⁻¹ was coincident with the literature data. The Ni/Ca₁₂Al₁₄O₃₃ catalyst was effective and relative cheap, which may be lead to reduction in the cost of hot gas cleaning process.     

Biomass to hydrogen via catalytic steam reforming of bio-oil over Ni-supported alumina catalysts

Production of hydrogen (H₂) from catalytic steam reforming of bio-oil was investigated in a fixed bed tubular flow reactor over nickel/alumina (Ni/Al₂O₃) supported catalysts at different conditions. The features of the steam reforming of bio-oil, including the effects of metal content, reaction temperature, W_bHSV (defined as the mass flow rate of bio-oil per mass of catalyst) and S/C ratio (the molar ratio of steam to carbon fed) on the hydrogen yield were investigated. Carbon conversion (moles of carbon in the outlet gases to moles of the carbon feed) was also studied, and the outlet gas distributions were obtained. It was revealed that the Al₂O₃ with 14.1% Ni content gave the highest yield of hydrogen (73%) among the catalysts tested, and the best carbon conversion was 79% under the steam reforming conditions of S/C = 5, W_bHSV = 13 1/h and temperature = 950 °C. The H₂ yield increased with increasing temperature and decreasing W_bHSV; whereas the effect of the S/C ratio was less pronounced. In the S/C ratio range of 1 to 2, the hydrogen yield was slightly increased, but when the S/C ratio was increased further, it did not have an effect on the H₂ production yield.     

Performance of Ni catalyst supported on La-hexaaluminate in CO<Subscript>2</Subscript> reforming of CH<Subscript>4</Subscript>

CO₂ reforming of CH₄ was performed using Ni catalyst supported on La-hexaaluminate which has been an well-known material for high-temperature combustion. La-hexaaluminate was synthesized by sol-gel method at various conditions where different amount of Ni (5–20 wt%) was loaded. Ni/La-hexaaluminate experienced 72 h reaction and its catalytic activity was compared with that of Ni/Al₂O₃, Ni/La-hexaaluminate shows higher reforming activity and resistance to coke deposition compared to the Ni/Al₂O₃ model catalyst. Coke deposition increases proportionally to Ni content. Consequently, Ni(5)/La-hexaaluminate(700) is the most efficient catalyst among various Ni/La-hexaaluminate catalysts regarding the cost of Ni in Ni(X)/La-hexaaluminate catalysts. BET surface area, XRD, EA, TGA and TPO were performed for surface characterization. This work was presented at the 6 ^th Korea-China Workshop on Clean Energy Technology held at Busan, Korea, July 4–7, 2006.     

Supported Cu Catalysts with Yttria-Doped Ceria for Steam Reforming of Methanol

The steam reforming of methanol was studied over Cu/Al₂O₃ catalysts with the addition of yttria-doped ceria (YDC). The YDC-modified catalysts were prepared by impregnating a -Al₂O₃ support with Y and Ce then with Cu. The addition of YDC drastically enhanced the activity of Cu/Al₂O₃ in the methanol reforming reaction. The enhanced activity was attributed to the increase of Cu⁺ species by YDC in the methanol reforming environment. However, the addition of YDC decreased the copper dispersion. The Cu dispersion could be enhanced by adding chromium oxide. The addition of YDC and Cr where Al₂O₃ was first impregnated with Cr then with YDC showed the most pronounced enhancement of the catalyst activity. At reaction temperatures of 200250 °C, the CO concentration in the products was smaller than 0.1%.     

Selectivity enhancement of Co-Mo/Al2O3 FCC gasoline hydrodesulfurization catalysts via incorporation of mesoporous Si-SBA-15

Mesoporous Si-SBA-15 was applied to enhance the FCC gasoline selective hydrodesulfurization (HDS) performance of conventional Co-Mo/Al₂O₃ catalysts and the physicochemical properties of the resulting catalyst were compared with those of Co-Mo/Al₂O₃ catalysts incorporated with macroporous kaolin, mesoporous Si-MCM-41 and microporous Si-ZSM-5. The selective HDS performances of all the catalysts were assessed with different FCC gasolines as feedstocks. The results showed that the HDS selectivity of the catalysts was closely related to the Mo sulfidation that depends on catalyst surface area and metal-support interaction. With the superior Mo sulfidation, the Co-Mo/Si-SBA-15-Al₂O₃ catalyst had the optimal HDS selectivity for not only the full-range FCC gasolines but also the heavy fractions thereof. The present article demonstrates the significance of enhancing Mo sulfidation in improving HDS selectivity and thus sheds a light on the development of highly selective HDS catalysts.     

The role of nickel in pyridine hydrodenitrogenation over NiMo/Al2O3

Al₂O₃ supported Mo, Ni, and NiMo/Al₂O₃ catalysts with various Ni contents were prepared to investigate the role of Ni as a promoter in a NiMo bimetallic catalyst system. The hydrodenitrogenation (HDN) reaction of pyridine as a catalytic probe was conducted over these catalysts under the same reaction conditions and the catalysts were characterized using BET surface area measurement, infrared spectroscopy, temperature programmed reduction, DRS and ESR. According to the results of reaction experiments, the NiMo/Al₂O₃ catalyst showed higher activity than Mo/Al₂O₃ catalyst in the HDN reaction and particularly the one with atomic ratio [Ni/(Ni+Mo)]=0.3 showed the best activity for the HDN of pyridine. The findings of this study lead us to suggest that the enhancement in the HDN activity with nickel addition could be attributed to the improvement in the reducibility of molybdenum and the formation of Ni-Mo-O phase.     

Effect of Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> xerogel support on hydrogen production by steam reforming of LNG over Ni/Al<Subscript>2</Subscript>O<Subscript>3</Subscript>-ZrO<Subscript>2</Subscript> catalyst

An Al₂O₃-ZrO₂ xerogel (AZ-SG) was prepared by a sol-gel method for use as a support for a nickel catalyst. The Ni/AZ-SG catalyst was then prepared by an impregnation method, and was applied to hydrogen production by steam reforming of LNG. A nickel catalyst supported on commercial alumina (A-C) was also prepared (Ni/A-C) for comparison. The hydroxyl-rich surface of the AZ-SG support increased the dispersion of nickel species on the support during the calcination step. The formation of a surface nickel aluminate-like phase in the Ni/AZ-SG catalyst greatly enhanced the reducibility of the Ni/AZ-SG catalyst. The ZrO₂ in the AZ-SG support increased the adsorption of steam onto the support and the subsequent spillover of steam from the support to the active nickel sites in the Ni/AZ-SG catalyst. Both the high surface area and the well-developed mesoporosity of the Ni/AZ-SG catalyst improved the gasification of adsorbed surface hydrocarbons in the reaction. In the steam reforming of LNG, the Ni/AZ-SG catalyst showed a better catalytic performance than the Ni/A-C catalyst. Moreover, the Ni/AZ-SG catalyst showed strong resistance toward catalyst deactivation.     

Characterization of aerogel Ni/Al2O3 catalysts and investigation on their stability for CH4-CO2 reforming in a fluidized bed

The CH₄-CO₂ reforming was investigated in a fluidized bed reactor using nano-sized aerogel Ni/Al₂O₃ catalysts, which were prepared via a sol–gel method combined with a supercritical drying process. The catalysts were characterized with BET, XRD, H₂-TPR and H₂-TPD techniques. Compared with the impregnation catalyst, aerogel catalysts exhibited higher specific surface areas, lower bulk density, smaller Ni particle sizes, stronger metal-support interaction and higher Ni dispersion degrees. All tested aerogel catalysts showed better catalytic activities and stability than the impregnation catalyst. Their catalytic stability tested during 48 h reforming was dependent on their Ni loadings. Characterizations of spent catalysts indicated that only limited graphitic carbon formed on the aerogel catalyst, while massive graphitic carbon with filamentous morphology was observed for the impregnation catalyst, leading to significant catalytic activity degradation. An aerogel catalyst containing 10% Ni showed the best catalytic stability and the lowest rate of carbon deposition among the aerogel catalysts due to its small Ni particle size and strong metal-support interaction.     

Partial Oxidation Reforming Catalyst for Fuel Cell-Powered Vehicles Applications

Transition metal oxide formulations for the partial oxidation (POX) reforming of isooctane were investigated for an onboard gasoline fuel processor. Ni/M/MgO/Al₂O₃ systems are more active than a commercial ICI catalyst. These catalysts showed better sulfur tolerance over the commercial ICI catalyst in the POX reforming of isooctane containing sulfur (Cs = 100 ppm). There was no apparent deactivation or modification of structure during 770h onstream. It was found that Ni/(Fe,Co)/MgO/Al₂O₃ catalyst is a promising candidate as POX reforming catalyst for gasoline fuel processor applications.     

Ethanol steam reforming reactions over Al2O3 · SiO2-supported Ni-La catalysts

Nickel-based catalysts supported on Al₂O₃ · SiO₂ were prepared with modification of the second metal involving La, Co, Cu, Zr or Y, of which the catalytic behaviors were assessed in the ethanol steam reforming reaction. Activity test indicated that addition of La resulted in higher selectivity of hydrogen and lower selectivity of carbon monoxide, compared with Co-doped nickel catalyst. Influences of lanthanum amounts on catalytic performance were studied over 30NixLa/Al₂O₃ · SiO₂ (x = 5, 10, 15), and characterizations by XRD, TPR and XPS indicated that low amount of lanthanum additives (5%) was superior to inhibit the crystal growth of nickel as well as beneficial to the reduction of nickel oxide. Finally 100 h test for the optimal catalyst 30Ni5La/Al₂O₃ · SiO₂ indicated its good long-term stability to provide high hydrogen selectivity and low carbon monoxide formation, as well as good resistance to coke deposition at low temperature.     

A highly efficient Cu/ZnO/Al2O3 catalyst via gel-coprecipitation of oxalate precursors for low-temperature steam reforming of methanol

The impact of preparation methods on the structure and catalytic behavior of Cu/ZnO/Al₂O₃ catalysts for H₂ production from steam reforming of methanol (SRM) has been reported. The results show that the nanostructured Cu/ZnO/Al₂O₃ catalyst obtained by a novel gel-coprecipitation of oxalate precursors has a high specific surface area and high component dispersion, exhibiting much higher activity in the SRM reaction as compared to the catalysts prepared by conventional coprecipitation techniques. It is suggested that the superior catalytic performance of the oxalate gel-coprecipitation-derived Cu/ZnO/Al₂O₃ catalyst could be attributed to the generation of “catalytically active” copper material with a much higher metallic copper specific surface as well as a stronger Cu–Zn interaction due to an easier incorporation of zinc species into CuC₂O₄ · x H₂O precursors as a consequence of isomorphous substitution between copper and zinc in the oxalate gel-precursors.