Pervaporation separation of water–ethanol mixtures using metal‐ion‐exchanged poly(vinyl alcohol) (PVA)/sulfosuccinic acid (SSA) membranes

Poly(vinyl alcohol)/sulfosuccinic acid (PVA/SSA) membranes in the hydrogen form were converted to monovalent metal ion forms Li⁺, Na⁺, and K⁺. The effect of exchange with metal ions was investigated by measuring the swelling of water–ethanol (10/90) mixtures at 30 °C and by the pervaporative dehydration performance test for aqueous ethanol solutions with various ethanol concentrations at 30, 40, and 50 °C. In addition, electron spectroscopy for chemical analysis (ESCA) analysis was carried out to study the quantity of metal ions in membranes. From the ESCA analysis, the lithium ion quantity in the resulting membranes is greater than that of any other metal ions in question because of the easy diffusion of a smaller metal ion into the membrane matrix. The swelling ratio was in the following order: PVA/SSA‐Li⁺ > PVA/SSA‐Na⁺ > PVA/SSA‐K⁺ membranes. For pervaporation, the PVA/SSA‐Na⁺ membrane showed the lowest flux and highest separation factor for all aqueous ethanol solutions. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1867–1873, 2002     

Thioether‐Functionalized Corn Oil Biosorbents for the Removal of Mercury and Silver Ions from Aqueous Solutions

Heavy‐metal contamination is one of the most important environmental problems faced in the world, particularly in developing countries. Metals such as silver and mercury from drinking water, food, and air sources can accumulate in living organisms and present significant health concerns. Meanwhile, the demand for these metals in many industries continues to increase. In the present study, thioether‐functionalized corn oil (TFCO) from a photoinitiated thiol‐ene synthesis was utilized to remove Ag⁺ and Hg²⁺ ions from an aqueous solution. An aqueous solution containing AgNO₃ and Hg[NO₃]₂ was prepared and contacted directly with TFCO. After vortex mixing for 60 s, the experiment ran for 351 min with the aqueous phase being periodically sampled for the analysis of metal ions (M ⁿ⁺). Results showed that 88.9% of Ag⁺ and 99.6% of Hg²⁺ ions were removed from the aqueous phase by the TFCO. Mass balances indicated that the total M ⁿ⁺ concentration in the oil phase was 13.890 g kg^?1 under the conditions studied. TFCO exhibited higher selectivity for removing Hg²⁺ than for Ag⁺ ions. Analysis of the adsorption kinetics showed that a pseudosecond‐order model may be used to determine the rate of Ag⁺ ion sorption by the oil phase. The presence of the Hg²⁺ ions interfered with the adsorption of Ag⁺ ions from the aqueous solution.     

Development of thin‐film composite membranes for carbon dioxide and methane separation using sulfonated poly(phenylene oxide)

Novel membranes based on sulfonated poly (phenylene oxide) (SPPO) was developed. SPPO membranes in the hydrogen form were converted to metal ion forms. The effect of exchange with metal ions including monovalent (Li⁺, Na⁺, K⁺), divalent (Mg²⁺, Ba²⁺, Ca²⁺) and trivalent (Al³⁺) ions was investigated in terms of permeation rate and permeation rate ratios for CO₂ and CH₄ gases. Both dense homogeneous membranes and thin‐film composite (TFC) membranes were studied for their gas separation characteristics. The effect of membrane preparation conditions and operating parameters on the membrane performance were also investigated. The selectivity of the TFC membrane increased as the cationic charge density increased as a result of electrostatic cross‐linking. TFC membrane of very high selectivity was achieved by coating a thin layer of SPPO‐Mg on a PES substrate. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 735–742, 2000     

Poly(2‐acrylamido glycolic acid‐co‐2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid): Synthesis,characterization, and retention properties for environmentally impacting metal ions

Poly(2‐acrylamido glycolic acid‐co‐2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) [P(AGA‐co‐APSA)] was synthesized by radical polymerization in an aqueous solution. The water‐soluble polymer, containing secondary amide, hydroxyl, carboxylic, and sulfonic acid groups, was investigated, in view of their metal‐ion‐binding properties, as a polychelatogen with the liquid‐phase polymer‐based retention technique under different experimental conditions. The investigated metal ions were Ag⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Cd²⁺, Pb²⁺, and Cr³⁺, and these were studied at pHs 3, 5, and 7. P(AGA‐co‐APSA) showed efficient retention of all metal ions at the pHs studied, with a minimum of 60% for Co(II) at pH 3 and a maximum close to 100% at pH 7 for all metal ions. The maximum retention capacity (n metal ion/n polymer) ranged from 0.22 for Cd²⁺ to 0.34 for Ag⁺. The antibacterial activity of Ag⁺, Cu²⁺, Zn²⁺, and Cd²⁺ polymer–metal complexes was studied, and P(AGA‐co‐APSA)–Cd²⁺ presented selective antibacterial activity for Staphylococcus aureus with a minimum inhibitory concentration of 2 μg/mL. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Modification of poly acrylic acid using calix[4]arene derivative for the adsorption of toxic heavy metals

Poly acrylic acid (PAA) was grafted with p‐t‐butyl calix[4]arene diamine (distal cone) (2) to adsorb toxic heavy metal and alkali metal cations. The grafting method includes the amidation reaction of PAA with calixarene diamine derivative 2 which was carried out in N,N‐dimethylformamide (DMF) and N–methyl‐2‐pyrrolidone (NMP) as solvents. The modified PAAs (PAA‐C1 and PAA‐C2) were characterized by FTIR, ¹H‐NMR, thermal gravimetric analysis (TGA) and differential scanning calorimetry (DSC). PAA‐C1 and PAA‐C2 were used to evaluate the sorption properties of some toxic heavy metal cations (Co²⁺, Cu²⁺, Cd²⁺, Hg²⁺), alkali metal cations (Na⁺, K⁺, Cs⁺), and Ag⁺. Results showed that the modified PAAs were good sorbents for heavy metal and alkali metal cations. The main goal of this project is to design hydrophobically modified PAA that is suitable for ion selective membranes and chemical sensor devices for adsorption of toxic heavy metals. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and adsorption selectivity for Hg(II) and Ag(I) of chelating resin immobilizing benzothiazolyl group on crosslinked polystyrene via hydrophilic sulfur‐containing PEG spacer

A new chelating resin incorporating 2‐mercaptobenzothiazole (MBZ) into macroporous chloromethylated polystyrene via hydrophilic spacer of polyethylene glycol containing sulfur was synthesized. The resin was characterized by elementary analysis and infrared spectra. The adsorption capacity of the resin for Ag⁺, Hg²⁺, Cu²⁺, Zn²⁺, and Pb²⁺ as a function of pH was determined. The effects of interference ions, such as Na⁺, Mg²⁺, Ca²⁺, Ba²⁺, Cu²⁺, Zn²⁺, and Pb²⁺, on percent recovery were also investigated. The results showed that the resin could effectively remove Hg²⁺ and Ag⁺ from solutions containing a large excess of Na⁺, Mg²⁺, Ca²⁺, Ba²⁺, Cu²⁺, Zn²⁺, and Pb²⁺. In column operation, it was observed that Hg²⁺ and Ag⁺ in trace quantities were effectively removed from binary metal ions. The percent recovery of the resin for Hg²⁺ and Ag⁺ was >98.6% and >97.5%, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 5034–5038, 2006     

Adsorption properties of novel chelating resins containing 2‐amino‐5‐methylthio‐1,3,4‐thiadizole and hydrophilic spacer arms for Hg2+ and Ag+

The adsorption properties, including the adsorption kinetics, adsorption isotherms, and adsorption selectivity, of newly formed chelating resins that contained a heterocyclic functional group and a hydrophilic spacer arm of poly(ethylene glycol) [polystyrene–diethylene glycol–2‐amino‐5‐methylthio‐1,3,4‐thiadizole (PS–DEG–AMTZ) and polystyrene–triethylene glycol–2‐amino‐5‐methylthio‐1,3,4‐thiadizole (PS–TEG–AMTZ)] were studied in detail. The results show that the adsorption kinetics of PS–DEG–AMTZ and PS–TEG–AMTZ for Hg²⁺ and Ag⁺ could be described by a pseudo‐second‐order rate equation. The introduction of a spacer arm between the polymeric matrix and functional group was beneficial for increasing the adsorption rates. The apparent activation energies of the resins for Hg²⁺ and Ag⁺ were within 20.89–32.32 kJ/mol. The Langmuir model could describe the isothermal process of Hg²⁺ and Ag⁺. The competitive adsorption of the resins for Hg²⁺ and Ag⁺ in binary mixture systems was also investigated. The results show that Hg²⁺ and Ag⁺ were adsorbed before the other metal ions, such as Cu²⁺, Zn²⁺, Fe³⁺, Cd²⁺, and Pb²⁺, under competitive conditions. Five adsorption–desorption cycles were conducted for the reuse of the resins. The results indicate that these two resins were suitable for reuse without considerable changes in the adsorption capacity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of poly(hydroxamic acid) chelating resin from poly(methyl acrylate)‐grafted sago starch

A new chelating ion‐exchange resin containing the hydroxamic acid functional group was synthesized from poly(methyl acrylate) (PMA)‐grafted sago starch. The PMA grafted copolymer was obtained by a free‐radical initiating process in which ceric ammonium nitrate was used as an initiator. Conversion of the ester groups of the PMA‐grafted copolymer into hydroxamic acid was carried out by treatment of an ester with hydroxylamine in an alkaline solution. The characterization of the poly(hydroxamic acid) chelating resin was performed by FTIR spectroscopy, TG, and DSC analyses. The hydroxamic acid functional group was identified by infrared spectroscopy. The chelating behavior of the prepared resin toward some metal ions was investigated using a batch technique. The binding capacities of copper, iron, chromium, and nickel were excellent and the copper capacity was maximum (3.46 mmol g⁻¹) at pH 6. The rate of exchange of the copper ion was very fast that is, t_1/2 < 5 min. It was also observed that the metal ion‐sorption capacities of the resin were pH‐dependent and its selectivity toward the metal ions used is in the following order: Cu²⁺ > Fe³⁺ > Cr³⁺ > Ni²⁺ > Co²⁺ > Zn²⁺ > Cd²⁺ > As³⁺ > Pb²⁺. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1256–1264, 2001     

Synthesis and adsorption properties of macroporous cross‐linked polystyrene that contains an immobilizing 2,5‐dimercapto‐1,3,4‐thiodiazole with tetraethylene glycol spacers

A novel chelating resin macroporous cross‐linked polystyrene immobilizing 2,5‐dimercapto‐1,3,4‐thiodiazole via a hydrophilic tetraethylene glycol spacer (PS‐TEG‐BMT) is synthesized and the structure is characterized by means of Fourier transform infrared spectroscopy (FTIR), energy dispersive X‐ray microanalysis (EDX), and elementary analysis. Its adsorption capacity for several metal ions such as Hg²⁺, Ag⁺, Ni²⁺, Pb²⁺, Cd²⁺, Fe³⁺, Bi³⁺, Zn²⁺, and Cu²⁺ are investigated. The initial experimental result shows that this resin has higher adsorption selectivity for Hg²⁺ and Ni²⁺ than for the other metal ions and the introduction of hydrophilic TEG spacer is beneficial to increase adsorption capacities. The result also shows that the Langmuir model is better than the Freundlich model to describe the isothermal process of PS‐TEG‐BME resin for Hg²⁺. Five adsorption‐desorption cycles demonstrate that this resin are suitable for reuse without considerable change in adsorption capacity. POLYM. ENG. SCI., 45:1515–1521, 2005. © 2005 Society of Plastics Engineers     

Transport properties of sulfonated poly (styrene‐isobutylene‐styrene) membranes with counter‐ion substitution

In this study, the transport properties of poly(styrene‐isobutylene‐styrene) (SIBS) were determined as a function of sulfonation level (0–94.9%) and counter‐ion substitution (Ba⁺², Ca⁺², Mg⁺², Mn⁺², Cu⁺², K⁺¹) for fuel cell applications. Increasing the sulfonation level improved the ion exchange capacity (IEC) of the membranes up a maximum (1.71 mequiv/g), suggesting a complex three‐dimensional network at high sulfonation levels. Results show that proton conductivity increases with IEC and is very sensitive to hydration levels. Methanol permeability, although also sensitive to IEC, shows a different behavior than proton conductivity, suggesting fundamental differences in their transport mechanism. The incorporation of counter‐ion substitution decreases both methanol and proton transport. Methanol permeability seems to be related to the size of the counter‐ion studied, while proton conductivity is more sensitive to water content, which is also reduced upon the incorporation of counter‐ions. To complement the studies, selectivity (i.e., proton conductivity/methanol permeability) of the studied membranes was determined and compared to Nafion® 117. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of ion‐imprinting chitosan/PVA crosslinked membrane for selective removal of Ag(I)

A novel ion‐imprinted membranes were synthesized for selective removal and preconentration for Ag(I) ions from aqueous solutions. The membranes were obtained via crosslinking of chitosan (CS), PVA, and blend chitosan/PVA using glutaraldehyde (GA) as crosslinker. The FTIR spectra were used to confirm the membrane formation. Comparing with the nonimprinted membranes, Ag(I)‐imprinted CS and CS/PVA has higher removal capacity and selectivity for Ag⁺ ions. An enhancement in the Ag⁺ removal capacity by ～ 20% (from 77.8 to 94.4 mg g^–1) and ～ 50% (from 83.9 to 125 mg g^–1) was found in the Ag(I)‐imprinted CS and Ag(I)‐imprinted CS/PVA membranes, respectively, when compared with the nonimprinted membranes. Removal equilibra was achieved in about 40 min for the non‐ and ion‐imprinted CS/PVA. The pH and temperature significantly affected the removal capacity of ion‐imprinted membrane. The relative selectivity coefficient values of Ag⁺/Cu²⁺ and Ag⁺/Ni²⁺ are 9 and 10.7 for ion‐imprinted CS membrane and 11.1 and 15 for ion‐imprinted CS/PVA membrane when compared with nonimprinted membranes. The imprinted membranes can be easily regenerated by 0.01M EDTA and therefore can be reused at least five times with only 15% loss of removal capacity. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Chelation ion‐exchange properties of copolymer resin derived from 4‐hydroxyacetophenone,oxamide, and formaldehyde

A copolymer (4‐HAOF) prepared by condensation of 4‐hydroxyacetophenone and oxamide with formaldehyde in the presence of an acid catalyst proved to be a selective chelating ion‐exchange copolymer for certain metals. Chelating ion‐exchange properties of this copolymer were studied for Fe³⁺, Cu²⁺, Ni²⁺, Co²⁺, Zn²⁺, Cd²⁺, Pb²⁺, and Hg²⁺ ions. A batch equilibrium method was employed in the study of the selectivity of metal‐ion uptake involving the measurements of the distribution of a given metal ion between the copolymer sample and a solution containing the metal ion. The study was carried out over a wide pH range and in media of various ionic strengths. The copolymer showed a higher selectivity for Fe³⁺ ions than for Co²⁺, Zn²⁺, Cd²⁺, Pb²⁺, Cu²⁺, Ni²⁺, and Hg²⁺ ions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 787–790, 2003     

Chromogenic sensing of Cu(II) by imino linked thiacalix[4]arene in mixed aqueous environment

Thiacalix[4]arene based imino receptors 4–5 carrying azophenol appendage have been synthesized and studied for their binding abilities towards different metal ions (Li⁺, Na⁺, K⁺, Cd²⁺, Ni²⁺, Cu²⁺, Zn²⁺, Ag⁺, Pb²⁺ and Hg²⁺). Receptor 4 showed selective chromogenic sensing for Cu²⁺ ions in mixed aqueous conditions (THF:H₂O, 9:1 v/v).     

Preparation and adsorption behavior of macrocyclic tetra‐amine derivatives of chitosan

The new macrocyclic polyamine derivatives of chitosan were synthesized by reacting epoxy‐activated macrocyclic tetra‐amine with the C6 hydroxyl or C2 amino group in chitosan. The obtained copolymers (CTS‐OM, CTS‐NM) contain amino functional groups, the secondary amines, and more polar hydroxyl groups in its skeleton. Elemental analysis, infrared spectra, and solid‐state ¹³C‐NMR analysis confirmed their structures. The adsorption behavior of the macrocyclic polyamine grafted chitosan for Ag⁺, Pb²⁺, Hg²⁺, and Cr³⁺ was investigated. The experimental results showed that the two novel derivatives of chitosan have high adsorption capacity and good selectivity for some metal ions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 407–412, 2005     

Metal‐solvating and self‐association of amphiphilic polyamides containing poly(oxyethylene) blocks

An amphiphilic poly(ether amide) consisting of hydrophilic poly(oxyethylene) amide blocks was prepared from the copolymerization of sebacic acid and two poly(oxyalkylene) diamines including a poly(oxyethylene) diamine (POE‐amine at 2000 M_w) and a poly(oxypropylene) diamine (POP‐amine at 230 M_w). The copolymer was estimated to have an average molecular weight of 15,000 M_w (GPC) or approximately three hydrophilic POE segments per strain. The presence of POE segments rendered polymer hydrophilicity and complexing ability for Li⁺, K⁺, Ca⁺², Ni⁺², Pd⁺², and Cu⁺² salts. In particular, lithium perchlorate affected the copolymer to the greatest extent in enhancing electrostatic dissipation or reducing surface resistivity as low as 10^5.0 Ω/sq (cross‐sectional area) at 1/180 Li⁺/EO from 10^7.2 Ω/sq (without metal ion). In such a metal complexation, the copolymer showed a new POE segmental crystalline phase at a melting temperature between ?10.4 and ?14°C, accompanied with the metal‐free original phase of ?31°C. In static toluene/water, the metal ions had no effect on the copolymer surfactancy in lowering the interfacial tension, reaching 4.4 dyn/cm at a critical micelle concentration (cmc) of 0.01 wt %. When mixing toluene and water, the lithium or nickel ions were found to be detrimental to the emulsifying process. Without the metal ion, fine droplets at average sizes of 4.5–5.0 μm were observed in the copolymer/ toluene/water emulsification. These amphiphilic behaviors of the POE‐segmented polyamide with or without metal ions were explained by the competing noncovalent bonding interactions among POE/metal ion/water. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 612–621, 2002     

Synthesis of Starch-Stabilized Ag Nanoparticles and Hg2+ Recognition in Aqueous Media

The starch-stabilized Ag nanoparticles were successfully synthesized via a reduction approach and characterized with SPR UV/Vis spectroscopy, TEM, and HRTEM. By utilizing the redox reaction between Ag nanoparticles and Hg²⁺, and the resulted decrease in UV/Vis signal, we develop a colorimetric method for detection of Hg²⁺ ion. A linear relationship stands between the absorbance intensity of the Ag nanoparticles and the concentration of Hg²⁺ ion over the range from 10 ppb to 1 ppm at the absorption of 390 nm. The detection limit for Hg²⁺ ions in homogeneous aqueous solutions is estimated to be ~5 ppb. This system shows excellent selectivity for Hg²⁺ over other metal ions including Na⁺, K⁺, Ba²⁺, Mg²⁺, Ca²⁺, Fe³⁺, and Cd²⁺. The results shown herein have potential implications in the development of new colorimetric sensors for easy and selective detection and monitoring of mercuric ions in aqueous solutions.     

A new rhodamine-based single molecule multianalyte (Cu, Hg) sensor and its application in the biological system

A new single molecule multianalyte sensor, vanillic aldehyde rhodamine 6G hydrazone has been designed for the selective detection of Cu²⁺ and Hg²⁺ ions. UV/Vis spectroscopy indicates that the sensor is a good chromogenic chemosensor for Cu²⁺ in 1:99 (v/v) ethanol-water media. Whereas, other ions, such as Li⁺, Na⁺, Mg²⁺, K⁺, Ca²⁺, Cr³⁺, Mn²⁺, Fe³⁺, Co²⁺, Ni²⁺, Zn²⁺, Ag⁺, Cd²⁺, Ba²⁺, Hg²⁺ and Pb²⁺ failed to generate a distinct response. Fluorescence spectral data reveals that the sensor is an excellent fluorescent chemosensor for Hg²⁺ in aqueous ethanol solution and with no fluorescent response toward other ions. The spectroscopic behavior of the sensor in living cells indicated that it can be used for the detection of Cu²⁺ and Hg²⁺ in environmental and biological systems. Mechanisms for the high selectivity of the sensor to Cu²⁺ and Hg²⁺ are discussed.     

Study of the synthesis of chitosan derivatives containing benzo‐21‐crown‐7 and their adsorption properties for metal ions

Three new chitosan crown ethers, N‐Schiff base‐type chitosan crown ethers (I, III), and N‐secondary amino type chitosan crown ether (II) were prepared. N‐Schiff base‐type chitosan crown ethers (I, III) were synthesized by the reaction of 4′‐formylbenzo‐21‐crown‐7 with chitosan or crosslinked chitosan. N‐Secondary amino type chitosan‐crown ether (II) was prepared through the reaction of N‐Schiff base type chitosan crown ether (I) with sodium brohydride. Their structures were characterized by elemental analysis, infrared spectra analysis, X‐ray diffraction analysis, and solid‐state ¹³C NMR analysis. In the infrared spectra, characteristic peaks of C?N stretch vibration appeared at 1636 cm^?1 for I and 1652 cm^?1 for II; characteristic peaks of N? H stretch vibration appeared at 1570 cm^?1 in II. The X‐ray diffraction analysis showed that the peaks at 2θ = 10° and 28° disappeared in chitosan derivatives I and III, respectively; the peak at 2θ = 10° disappeared and the peak at 2θ = 28° decreased in chitosan‐crown ether II; and the peak at 2θ = 20° decreased in all chitosan derivatives. In the solid‐state ¹³C NMR, characteristic aromatic carbon appeared at 129 ppm in all chitosan derivatives, and the characteristic peaks of carbon in C?N groups appeared at 151 ppm in chitosan crown ethers I and III. The adsorption and selectivity properties of I, II, and III for Pd²⁺, Au³⁺, Pt⁴⁺, Ag⁺, Cu²⁺, and Hg²⁺ were studied. Experimental results showed these adsorbents not only had good adsorption capacities for noble metal ions Pd²⁺, Au³⁺, Pt⁴⁺, and Ag⁺, but also high selectivity for the adsorption of Pd²⁺ with the coexistence of Cu²⁺ and Hg²⁺. Chitosan‐crown ether II only adsorbs Hg²⁺ and does not adsorbs Cu²⁺ in an aqueous system containing Pd²⁺, Cu²⁺, and Hg²⁺. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1886–1891, 2002     

Influence of the Eu2+ on the Silver Aggregates Formation in Ag+–Na+ Ion‐Exchanged Eu3+‐Doped Sodium–Aluminosilicate Glasses

Europium‐doping sodium–aluminosilicate glasses are prepared by melt‐quenching method, in which europium ions were spontaneously reduced from their trivalent to divalent state. The silver was introduced into glasses by Ag⁺–Na⁺ ion exchange and the interactions between europium ions and silver species were investigated. Owing to energy transfer (ET) from Ag⁺/silver aggregates to Eu³⁺, significant enhancements of Eu³⁺ emission were observed for 285/350‐nm excitation, respectively. The divalent europium ions promote the formation of silver aggregates in the process of ion exchange.     

Synthesis and Metal‐ion Binding Properties of New N2S4O2‐ and N2S5O2‐Donor Macrocycles

Abstract

Synthetic procedures for new mixed‐donor macrocycle compounds were reported. The macrocyclic compounds were used in solvent extraction metal picrates such as Ag⁺, Hg²⁺, Cd²⁺, Zn²⁺, Cu²⁺, Ni²⁺, Mn²⁺, Pb²⁺, and Co²⁺. The metal picrate extractions were investigated at 25±0.1°C with the aid of UV‐visible spectrometry. It was found that 6,7,9,10,12,13,23,24‐octahydro‐19H,26Hdibenzo[h,t](1,4,7,13,16,22,10,19) dioxatetrathiadiazasiclotetracosine‐20,27(21H,28H)‐dione showed selectivity towards Ag⁺, Hg²⁺, and Cd²⁺ among the other metals. The extraction constants (Log K_ex) and complex compositions were determined for the Ag⁺ and Hg²⁺ complexes for this compound and 9,10,12,13,23,24,26,27,29,30‐decahydro‐5H,15H‐dibenzo‐[h,w][1,4,7,13,16,19,25‐,10,22] dioxapentathiadiazacycloheptacosine‐6,16(7H,17H)‐dione.