High‐field electrical properties of new LDPE films prepared using metallocene catalyst

Now low‐density polyethylene (M‐LDPE) prepared using metallocene catalyst has narrower composition distribution and molecular weight distributions than linear low‐density polyethylene (LLDPE) using Ziegler catalyst. The authors compared the electrical insulating properties of M‐LDPE films and conventional LLDPE films. The high‐field current of M‐LDPE was found to be lower than that of LLDPE. The difference in current increased with the decrease of temperature. The high‐field current was much reduced in M‐LDPE with a low melting point. The impulse breakdown strength of M‐LDPE increased with the decrease of temperature. The insulating properties of M‐LDPE with a low melting point were improved at 30 °C. These results were explained by the fact that M‐LDPE with a low melting point includes more low‐molecular‐weight components. We also discuss the effects of antioxidant on the electrical properties of M‐LDPE. We compared the electrical conduction and breakdown strength of undoped M‐LDPE and antioxidant‐doped M‐LDPE. Differences in their electrical properties were minor. It was found that the excellent properties of M‐LDPE do not depend on the effects of antioxidant. © 1999 Scripta Technica, Electr Eng Jpn, 130(2): 1–9, 2000     

MgO/LDPE纳米复合材料抑制空间电荷及电树枝化特性

应用经硅烷偶联处理后的纳米氧化镁(MgO)粉末与低密度聚乙烯(low density polyethylene,LDPE)共混,制得MgO/LDPE复合介质。高成分衬度扫描电镜(scanningelectron microscope,SEM)中图像表明,粒径为100 nm左右的MgO纳米粒子均匀的分散于介质中。通过电声脉冲法(pulsed electro-acoustic,PEA)测试发现,当纳米MgO填料的质量分数为4%时,可以有效抑制空间电荷的注入,伏安特性的实验结果表明,复合介质拥有更高的空间电荷注入阈值场强。通过电树枝实验,发现复合介质可以抑制电树枝的引发和生长。最后,对实验结果进行了分析,探讨了纳米复合介质抑制空间电荷和树枝化生长的机制。纳米颗粒与基体材料界面电荷行为可能是复合介质电学性能改善的原因。     

Space charge formation and breakdown in polyethylene influenced by the interface with semiconducting electrodes

This paper deals with the influence of interface between polyethylene and semiconducting electrode on the space charge formation and electrical breakdown. Low‐density polyethylene (LDPE) films attached with different semiconducting electrodes were subjected to the DC breakdown test, and corresponding space charge distribution was measured. A heat treatment to LDPE itself did not bring about a significant change in space charge profile; however, when a semiconducting electrode was hot‐pressed, the impurities would migrate into LDPE at high temperature, leading to the change in space charge profile. Furthermore, it was suggested from the comparison between the results with degassed and as‐received semiconducting electrodes that some carriers relating to impurities in the electrode would move into LDPE under the voltage. In addition, it was shown that the breakdown is not determined by the field at the cathode which can supply sufficient electrons, but by the maximum field across the specimen, suggesting that an increase in conduction current due to the generation and/or injection, rather than the electronic avalanche process, leads to the breakdown. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 19–25, 2002     

Space charge behavior in low-density polyethylene

The space charge distribution in low-density polyethylene (LDPE) was measured with the pulsed electroacoustic (PEA) method. We used three types of LDPE: LDPE-L and LDPE-H were prepared by the high pressure process, and m-LDPE was polymerized with a metallocene catalyst. Space charge in LDPE strongly depended upon the electrode material. Semiconductive electrodes enhanced carrier injection into LDPE and, as a result, space charge. The density, polymerization process, applied field, temperature and so on also affected the space charge behavior. This space charge behavior was compared with the results of dc current measurements     

Impulse breakdown superposed on ac voltage in XLPE cable insulation

This paper discusses tree inception and breakdown voltage characteristics of XLPE cable insulation subjected to impulse voltages superimposed on ac voltage. The tree initiation tests were performed on laboratory-molded specimens equipped with needle electrodes, whereas the breakdown tests were conducted on a full-sized cable. The impulse tree initiation stress was found to be dependent on the magnitude of the pre-applied ac stress and the relative polarities of the impulse and the ac peak at the instant of their superposition. Although the impulse polarity has an effect on the tree inception, the general behavior is that the tree inception stress always decreases with an increase of the pre-applied ac stress. This phenomenon is discussed in terms of the space charge effect and the influence of the impulse voltage application itself. The impulse strength of a full-sized cable insulation was found to be independent of the pre-applied ac stress as long as that stress did not exceed the operating stress of a 500 kV cable insulation. However, subjecting cable insulation to higher ac stresses before impulse application caused a reduction of its breakdown strength as compared with the insulation without ac prestressing     

High‐field electrical properties under AC voltage application in acetophenone‐coated LDPE film

This paper deals with the effects of acetophenone coating on dielectric properties such as tan δ and capacitance and on space charge formation up to electrical breakdown under AC voltage application in low‐density polyethylene (LDPE) film. The existence of acetophenone at the electrical interface enhances tan δ. tan δ in acetophenone‐coated specimens increased with electric field and decreased with the frequency in the high‐field and high‐temperature region. AC breakdown test revealed that the electric strength in noncoated specimens was higher than in acetophenone‐coated specimens, and that the electric strength also decreased with temperature. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 142(3): 1–7, 2003; Published online in Wiley InterScience (www.interscience. wiley.com). DOI 10.1002/eej.10086     

交流叠加冲击电压下XLPE绝缘中电树起始特性

ＸＬＰＥ绝缘在交流叠加冲击电压作用下电树起始特性的试验研究表明,电树的冲击起始场强不仅与预加的交流电压的大小有关,还与冲击电压与交流电压的相对极性有关,并有明显的累积效应,起晕也有明显的时延现象。     

High repetition rate PEA system for in-situ space charge measurement during breakdown tests

In order to investigate transient space charge phenomena, it is essential that the space charge profile be observed at a high repetition rate. We have developed a new space charge measurement system using the pulsed electroacoustic (PEA) method, which can measure the space charge profiles every 10 /spl mu/s. It employs the most recent digitising oscilloscope model and a semiconductor switch. The effect of prestressing on impulse breakdown voltage of a low-density polyethylene sheet was investigated by using the new system. Experimental results suggest that positive charge injection was dominant immediately before the breakdown, and charge injection during the prestressing causes distortion of the electric field near the electrode, and enhances the subsequent charge injection due to the impulse voltage.     

DC conduction and electrical breakdown of MgO/LDPE nanocomposite

To understand basic electric properties of nano-sized magnesium oxide (MgO) / low-density polyethylene (LDPE) nanocomposite under DC voltage application, the volume resistivity, the space charge distribution and the breakdown strength were investigated. By the addition of nano-sized MgO filler, both the DC breakdown strength and the volume resistivity of LDPE increased. At the average DC electric field of about 85 kV/mm and more, a positive packet space charge was observed in LDPE without MgO nano-filler, whereas a little homogeneous space charge was observed in MgO/LDPE nanocomposite material at the front of electrode. From these results, it is confirmed that the addition of MgO nano-filler leads to the improvement of DC electrical insulating properties of LDPE.     

茂金属聚乙烯改善低密度聚乙烯的介电性能

针对高压、超高压直流塑料电缆中存在的空间电荷效应,大多数直流电力电缆常采用改性方法提高其介电性能,如空间电荷特性、体积电阻率和击穿强度等。常用的改性方法主要有添加剂、共混、接枝和二元共聚4种。共混技术较广泛用以改性聚乙烯电缆,提高其介电性能。因此用电声脉冲法(PEA)测量了MPE与LDPE共混试样中的空间电荷分布;用高阻计测量了共混物的体积电阻率,用阶梯电压测量了共混物的交流击穿场强。试验结果表明,1%MPE与LDPE共混能有效降低空间电荷效应,提高交流击穿场强7.9%,略降低体积电阻率。最后讨论了共混物的物质结构、电荷陷阱及介电性能间的关系。     

Transient phenomena of current and field distortion due to dynamics of packet‐like charges in LDPE films

Simultaneous measurements of space charge and external current were carried out using a PEA measurement system with an electrometer on the back of a grounding electrode in order to clarify the physical situation of a huge packet of positive space charges in LDPE films. A large number of positive charges from a semiconducting anode were accumulated at the interface between LDPE and an Al‐cathode at a mean applied field of 1.5 MV/cm and then finally disappeared. The results of simultaneous measurements showed that the external current kept a relatively high value during charge accumulation and further increased when the charges disappeared. Both the charge dynamics and the external current were restricted by addition of a low‐molecular‐weight paraffin wax, indicating that carrier transport was influenced by the microstructure of the polymer. The dynamics of the residual charges after short‐circuiting is also discussed. © 2012 Wiley Periodicals, Inc. Electr Eng Jpn, 179(4): 10–17, 2012; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/eej.21256     

Time‐frequency analysis of a pressure wave caused by impulse tree using wavelet transform

This paper describes results of time‐frequency analysis of a pressure wave caused by impulse tree extension using wavelet transform. Pressure waves were measured by a piezo sensor which was located on the back of the plane electrode when high‐voltage nanosecond pulses were applied to a point electrode in a low‐density polyethylene block. Frequency of the pressure wave from induced charges on the plane electrode was higher than that of the pressure wave from tree. In addition, the frequency of the pressure wave from tree tended to decrease with increasing gap length because of the dispersion of the pressure wave during its propagation. When a large tree extension occurred between a 5‐mm gap, pressure waves of about 10 MHz propagated from the tree tip and a pressure wave of 1 MHz propagated from the tree stem. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 142(1): 1–7, 2003; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10097     

低密度聚乙烯/纳米蒙脱土复合材料的水树枝生长特性

低密度聚乙烯是高压电力电缆的主要绝缘材料,水树枝生长特性与聚乙烯高压电力电缆绝缘击穿具有紧密联系。采用熔融插层复合法制备了一种低密度聚乙烯/蒙脱土纳米复合材料;设计制作了纳米复合材料的水树枝老化试样及试验装置,在试验中观测了试样的水树枝生长长度,并对试样的水树枝引发率进行了统计,分析了低密度聚乙烯/蒙脱土纳米复合材料的吸水率对水树枝生长的影响;采用差示扫描热法分析了试样的结晶度和晶粒尺寸均匀性,通过分析低密度聚乙烯/蒙脱土纳米复合材料的结晶行为,说明了纳米蒙脱土对纳米复合材料中水树枝的抑制机理。试验与分析结果表明:掺杂质量分数为3%的纳米蒙脱土粒子能够有效地提高低密度聚乙烯的结晶度,使晶粒尺寸分布均匀,吸水率减小,延缓水树枝在低密度聚乙烯中的引发与生长。     

空间电荷对SF_6气体正雷电冲击击穿的作用

利用两种实验方法对比测试了预注入单极性空间电荷时,SF_6气体极不均匀场间隙正雷电冲击击穿特性。分析表明;直流叠加冲击电压法不适用于观察空间电荷的作用,而切换直流/冲击电压法能有效地反映空间电荷对冲击击穿的作用。     

Effects of manufacturing technology on electrical breakdown and morphology of thin films of low density polyethylene blended with polypropylene copolymer

Extruded films prepared from blends of low-density polyethylene (LDPE) and random copolymer of ethylene and propylene (EP) with the T-die method were studied with respect to electrical properties and morphology. Comparisons with data on blown films are made. These blends are of interest as improved LDPE for making XLPE for insulated power cable. In the high temperature region (90/spl deg/C), a specimen with a slightly higher EP content had higher impulse breakdown strength than that with a lower EP content, but no improvement of DC breakdown strength by blending could be found. The improvement of impulse breakdown strength (90/spl deg/C) is explained in terms of morphological changes by blending such as the orientation of chains in a film and the size of spherulites on the assumption of the thermal breakdown. In comparison, a T-die film had higher impulse breakdown strength than that of a blown film for the same composition. The impulse breakdown strength also increased with the use of the higher density LDPE. In the current versus electric field characteristics at 30/spl deg/C, the blend polymer with EP content of 5-10% showed a transition from LDPE behavior at low field region to EP behavior at high field region. However, no appreciable difference in current behavior among the specimens was observed at 90/spl deg/C, which suggests an incompatibility between the two materials that exists at 30/spl deg/C but not at 90/spl deg/C.     

Visualization of high‐speed phenomena using an acousto‐optic laser deflector

An acousto‐optic laser deflector was used for visualization of high‐speed phenomena, such as shock waves and density perturbations accompanying an impulse discharge, or shock waves generated by laser‐induced breakdown in air. Using a continuous wave laser as the light source, shadowgraphs of shock waves and density perturbations were obtained at shutter speeds down to 1µs. Results showed that shock waves propagated at a speed of 417 m/s in the case of an impulse discharge, and 485 m/s in the case of laser‐induced breakdown. Prebreakdown phenomena such as leaders progressing from the high‐voltage electrode were also visualized. Compared to conventional high‐speed imaging techniques, this method is useful when using a laser light source, since the acousto‐optic crystal can accommodate high‐intensity laser light. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 154(3): 9–15, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20279     

Impulse partial discharge and breakdown characteristics of rod–plane gaps in air and N2 gases

In response to growing environmental concerns, we attempted to develop switchgear without using SF₆ gas. In our research, we used compressed air and pure N₂ as an electrical insulation gas, because of their low global warming potential. In this paper, we examined the impulse breakdown and impulse partial discharge characteristics under various conditions related to nonuniformity of the electric field. The experimental results show that the breakdown voltage (BDV) of air is higher than that of pure N₂ gas under highly nonuniform field conditions in the rod–plane gap. On the other hand, the discharge inception voltage of air and N₂ were almost the same. Furthermore, first partial discharge (PD), leader discharge, and its transition to the breakdown were successfully observed through the measurement of discharge current and light emissions under impulse voltage application. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 148(3): 36–43, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10277     

Dielectric characteristics of oil‐filled transformer in the presence of nonstandard lightning surge waveforms

To achieve a rational insulation design for transformers, it is important to evaluate dielectric strength against surges actually impinging on equipment on‐site. This paper deals with the breakdown voltage characteristics of an oil gap under nonstandard lightning surge waveforms combined with oscillatory voltages. It is found that the breakdown voltages of the oil gap under nonstandard impulse waveforms are higher than standard lightning impulse voltages. The results can be ascribed to V–t characteristics of the oil gap in short‐time impulse voltage ranges. © 2003 Wiley Periodicals, Inc. Electr Eng Jpn, 146(3): 39–45, 2004; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10229     

The influence of antioxidants on electrical tree generation in XLPE

In conjunction with previous experiments studying the effect of decomposition products of dicumyl peroxide (DCP) and antioxidants (AOs) in cross‐linked polyethylene (XLPE) insulation on electrical tree generation, the authors conducted experiments investigating tree inhibition by phenolic AOs. The experiments were conducted using XLPE slabs containing four different phenolic AOs. Among the specimens containing these AOs, the specimen containing 4,4é‐thio‐bis(3‐methyl‐6‐tert‐butylphenol) was found to show the highest tree inception voltage. To examine the reasons for the significant increase in tree inception voltage in this specimen, further experiments were carried out on XLPE specimens containing both phenolic AO and a sulfur‐containing AO. The results demonstrated that the tree inception voltages of specimens containing both phenolic AO and sulfur‐containing AO were higher than those of the specimens containing only one of these two types of AOs. The roles of antioxidants in XLPE dielectrics are discussed with reference to the mechanisms of autoxidation of polymeric materials. The great increase in the tree inception voltage of XLPE specimens containing 4,4é‐thio‐bis(3‐methyl‐6‐tert‐butylphenol) appears to be due to a synergistic effect between the phenolic AO and the sulfur‐containing AO. © 2001 Scripta Technica, Electr Eng Jpn, 135(3): 1–7, 2001     

Properties of Space Charge Distributions and Conduction Current in XLPE and LDPE under DC High Electric Field

Space charge behavior and conduction current in polyethylene under dc stress were investigated. One of the reasons for the different breakdown property in cross‐linked polyethylene (XLPE) from that in low‐density polyethylene (LDPE) may be based on the existence of cross‐linking by‐products in XLPE. Furthermore, a thermal history in cross‐linking process for XLPE may also cause of the difference. It is generally accepted that the existence of the cross‐linking by‐products increase the conduction current in XLPE under dc stress. It is also said that an anneal treatment in air atmosphere may affect to the electrical properties under dc stress. Therefore, we investigated the effect of the cross‐linking by‐products and the anneal treatment on space charge behavior and conduction current in polyethylene under dc stress. In our research, it is thought that the increasing dissipation power in XLPE is the cause of the breakdown in it under dc stress. Therefore, to calculate the dissipation power in the bulk of test sample, we measured the space charge distribution and the external circuit current simultaneously. Based on the results, we discussed the reason of the difference of the space charge properties in XLPE and LDPE focusing on the cross‐linking by‐products and the oxidation of the test samples.