Low molecular weight block copolymers as plasticizers for polystyrene

Polystyrene‐b‐alkyl, polystyrene‐b‐polybutadiene‐b‐polystyrene, and polystyrene‐b‐poly(propylene glycol)monotridecyl ether were synthesized using macro initiators and atom transfer radical polymerization or by esterifications of homopolymers. The aim was a maximum molecular weight of 4 kg/mol and minimum polystyrene content of 50 w/w %, which by us is predicted as the limits for solubility of polystyrene‐b‐alkyl in polystyrene. DSC showed polystyrene was plasticized, as seen by a reduction in glass transition temperature, by block copolymers consisting of a polystyrene block with molecular weight of approximately 1 kg/mol and an alkyl block with a molecular weight of approximately of 0.3 kg/mol. The efficiency of the block copolymers as plasticizers increases with decreasing molecular weight and polystyrene content. In addition, polystyrene‐b‐alkyl is found to be an efficient plasticizer also for polystyrene‐b‐polyisoprene‐b‐polystyrene (SIS) block copolymers. The end use properties of SIS plasticized with polystyrene‐b‐alkyl, measured as tensile strength, is higher than for SIS plasticized with dioctyl adipate. The polystyrene‐b‐polybutadiene‐b‐polystyrene and polystyrene‐b‐poly(propylene glycol)monotridecyl ether series were only partially soluble in polystyrene and insoluble in the polystyrene phase of SIS. For the lowest molecular weight samples, this leads to measurable plasticization of polystyrene but no plasticization of SIS. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 981–991, 2005     

Synthesis of block copolymers from PDMS macroinitiators

The synthesis of polystyrene‐b‐polydimethylsiloxane‐b‐polystyrene (PSt‐b‐PDMS‐b‐PSt) copolymers is described. Commercially available difunctional PDMS containing vinylsilyl terminal species was reacted with hydrogen bromide resulting in the PDMS macroinitiators. The terminal alkyl bromide groups were then used as initiators for atom transfer radical polymerization (ATRP) to produce block copolymers. Using this technique, triblock copolymers consisting of a PDMS centre block and polystyrene terminal blocks were synthesized. ATRP of St from those macroinitiators showed linear increases in M_n with conversion, demonstrating the effectiveness of ATRP to synthesize a variety of inorganic/organic polymer hybrids. Copyright © 2004 Society of Chemical Industry     

Synthesis and properties of polystyrene‐b‐poly(ethylene oxide)‐b‐polystyrene triblock copolymers

A series of well‐defined and property‐controlled polystyrene (PS)‐b‐poly(ethylene oxide) (PEO)‐b‐polystyrene (PS) triblock copolymers were synthesized by atom‐transfer radical polymerization, using 2‐bromo‐propionate‐end‐group PEO 2000 as macroinitiatators. The structure of triblock copolymers was confirmed by ¹H‐NMR and GPC. The relationship between some properties and molecular weight of copolymers was studied. It was found that glass‐transition temperature (T_g) of copolymers gradually rose and crystallinity of copolymers regularly dropped when molecular weight of copolymers increased. The copolymers showed to be amphiphilic. Stable emulsions could form in water layer of copolymer–toluene–water system and the emulsifying abilities of copolymers slightly decreased when molecular weight of copolymers increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 727–730, 2006     

Surface properties of block and graft polystyrene–polydimethylsiloxane copolymers

The surface compositions of a series of polystyrene‐b‐polydimethylsiloxane (PS‐b‐PDMS) and polystyrene‐g‐polydimethylsiloxane (PS‐g‐PDMS) copolymers were investigated using ATR‐FTIR and XPS technique. The results showed that enrichment of PDMS soft segments occurred on the surface of the block copolymers as well as on that of graft copolymers. And the magnitude order of the enrichment was as follows: PS‐b‐PDMS > PS‐g‐PDMS, which was attributed to the facilitating of the movement of the PDMS segments in PS‐b‐PDMS copolymer. Meanwhile, the solvent type and the contact medium had influence on the accumulation of PDMS on the surfaces. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Synthesis and characterization of PS‐b‐PDMS‐b‐PS triblock copolymer

A series of polystyrene‐b‐poly(dimethylsiloxane)‐b‐polystyrene (PS/PDMS/PS) triblock copolymers had been synthesized by atom transfer radical polymerization (ATRP). The products had been characterized by Fourier transform infrared, gel permeation chromatography, differential scanning calorimetry, thermogravimetric analysis, contact angle, and scanning electron microscope. The results indicate that the PS chains have been successfully blocked onto the PDMS back bone, and the PS‐b‐PDMS‐b‐PS triblock copolymers have low‐surface tension, good thermal stability, and microphase separation configuration. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis of polystyrene‐b‐poly(ethylene‐co‐butene) block copolymers by anionic living polymerization and subsequent noncatalytic hydrogenation

A series of polystyrene‐b‐polybutadiene (PSt‐b‐PBd) block copolymers with various chain lengths and compositions were synthesized by sequential living anionic polymerization and then converted into the corresponding polystyrene‐b‐poly(ethylene‐co‐butene) (PSt‐b‐PEB) block copolymers through the selective hydrogenation of unsaturated polybutadiene segments. Noncatalytic hydrogenation was carried out with diimide as the hydrogen source. The microstructures of PSt‐b‐PBd and PSt‐b‐PEB were investigated with gel permeation chromatography, ¹H‐NMR, ¹³C‐NMR, Fourier transform infrared, and differential scanning calorimetry. The results showed that the hydrogenation reaction was conducted successfully and that the chain length and molecular weight distribution were not altered by hydrogenation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2632–2638, 2006     

Controllable design of nanostructure in block copolymer reinforced epoxy composites

The modification of epoxy composites through the construction of nanostructures via the self‐organization of block copolymers in epoxy has become a hot topic. In this research, polystyrene‐b‐poly(?‐caprolactone)‐b‐polydimethylsiloxane‐b‐poly(?‐caprolactone)‐b‐polystyrene (PS‐PCL‐PDMS‐PCL‐PS) block copolymers with different lengths of PS subchains were synthesized and incorporated into epoxy thermoset. Due to the difference in the length of PS subchains, two different sizes of core‐shell nanostructures were obtained. When these two block copolymers were incorporated into epoxy, the tensile strength, elongation at break, damping temperature in range (tan δ > 0.2), and storage modulus of the epoxy thermoset below 105 °C were simultaneously improved. Meanwhile, the effects of the lengths of PS subchains on the size of nanostructures and the relationship between microstructure and macroscopic properties of epoxy composites were systematically investigated. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46362.     

Synthesis and characterization of Pst‐b‐PDMS‐b‐PSt copolymers by atom transfer radical polymerization

Polystyrene‐b‐poly(dimethylsiloxane)‐b‐polystyrene (Pst‐b‐PDMS‐b‐PSt) triblock copolymers were synthesized by atom transfer radical polymerization (ATRP). Commercially available difunctional PDMS containing vinylsilyl terminal species was reacted with hydrogen bromide, resulting in the PDMS macroinitiators for the ATRP of styrene (St). The latter procedure was carried out at 130°C in a phenyl ether solution with CuCl and 4, 4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as the catalyzing system. By using this technique, triblock copolymers consisting of a PDMS center block and polystyrene terminal blocks were synthesized. The polymerization was controllable; ATRP of St from those macroinitiators showed linear increases in M_n with conversion. The block copolymers were characterized with IR and ¹H‐NMR. The effects of molecular weight of macroinitiators, macroinitiator concentration, catalyst concentration, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP are reported. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3764–3770, 2004     

Synthesis and characterization of novel polystyrene‐block‐polyurethane‐block‐polystyrene tri‐block copolymers through atom transfer radical polymerization

Background: Radical polymerization is used widely to polymerize more than 70% of vinyl monomers in industry, but the control over molecular weight and end group of the resulting polymers is always a challenging task with this method. To prepare polymers with desired molecular weight and end groups, many controlled radical polymerization (CRP) ideas have been proposed over the last decade. Atom transfer radical polymerization (ATRP) is one of the successful CRP techniques. Using ATRP, there is no report on the synthesis of polystyrene‐block‐polyurethane‐block‐polystyrene (PSt‐b‐PU‐b‐PSt) tri‐block copolymers. Hence this paper describes the method of synthesizing these tri‐block copolymers. To accomplish this, first telechelic bromo‐terminated polyurethane was synthesized and used further to synthesize PSt‐b‐PU‐b‐PSt tri‐block copolymers using CuBr as a catalyst and N,N,N,N″,N″‐pentamethyldiethylenetriamine as a complexing agent. Results: The ‘living’ nature of the initiating system was confirmed by linear increase of number‐average molecular weight and conversion with time. A semi‐logarithmic kinetics plot shows that the concentration of propagating radical is steady. The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and differential scanning calorimetry show that the novel PSt‐b‐PU‐b‐PSt tri‐block copolymers were formed through the ATRP mechanism. Conclusion: For the first time, PSt‐b‐PU‐b‐PSt tri‐block copolymers were synthesized through ATRP. The advantage of this method is that the controlled incorporation of polystyrene block in polyurethane can be achieved by simply changing the polymerization time. Copyright © 2007 Society of Chemical Industry     

Structure and thermal behavior of nylon‐6/polytetrahydrofuran triblock copolymers obtained via anionic polymerization

The structure, crystallization, and phase behavior of nylon6‐b‐polytetrahydrofuran‐b‐nylon6 triblock copolymers synthesized via activated anionic polymerization have been studied. The composition, molecular weight of polytetrahydrofuran (PTHF) soft block, and type of polymeric activators (PACs) have been varied. Differential Scanning Calorimetry (DSC), Wide‐Angle X‐ray Diffraction (WAXD), Transmission Electron Microscopy (TEM), and Polarized Light Microscopy (PLM) experiments have revealed that in triblock copolymers only the nylon‐6 component crystallizes while PTHF segments are amorphous. The soft blocks do not alter the spherulitic crystalline structure of nylon‐6 and hard blocks crystallize in the α‐modification. The degree of crystallinity decreases with increasing PTHF concentration. The phase behavior has been investigated by Dynamic Mechanical Thermal Analysis (DMTA). Two different glass transition temperatures (T_g) for all samples have been observed. This indicates that nylon‐6 and PTHF segments are not molecularly miscible and the copolymers are microphase separated. The mechanical properties of the copolymers synthesized have been evaluated. Nylon‐6 copolymers with soft block concentrations up to 10 w/w %, exhibit improved notched impact strength in comparison to the nylon‐6 homopolymer, retaining relatively high hardness and tensile strength. All copolymers possess low water absorption and good thermal stability. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1448–1456, 2002; DOI 10.1002/app.10448     

Synthesis and characterization of poly (styrene‐b‐[(butadiene)1−x‐(ethylene‐co‐butylene)x] ‐b‐styrene) star‐like molecular polymers produced by partial hydrogenation of SBS

This article reports the synthesis and characterization of four arm star‐shaped poly(styrene‐b‐[(butadiene)_1?x‐(ethylene‐co‐butylene)_x]‐b‐styrene) (SBEBS) copolymers. A series of SBEBS copolymers with different compositions of the elastomeric block were produced by hydrogenating a given poly(styrene‐b‐butadiene‐b‐styrene) (SBS) copolymer using a catalyst prepared from bis(η⁵‐cyclopentadienyl)titanium(IV) dichloride and n‐butyllithium. The characterization was accomplished by proton nuclear magnetic resonance spectroscopy (¹H NMR), infrared spectroscopy (FTIR), gel permeation chromatography (GPC), differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA). The results indicate that there is a selective saturation of the polybutadiene block over the polystyrene block; this selectivity was determined by the Ti/Li molar ratio and the concentration of Ti. It was observed that the saturation rate of the 1,2‐vinyl was higher than that of the 1,4‐trans and 1,4‐cis poly(butadiene)‐b isomers. The DSC and DMA results indicate that the degree of hydrogenation had a profound effect on the polymer's relaxation behavior. All samples exhibited a biphasic system behavior with two distinct transitions corresponding to the elastomeric and polystyrene blocks. SBEBS copolymers with higher saturation levels (>33%) exhibited a crystalline character. The TGA results indicated a characteristic weight loss temperature in all samples, with slightly higher thermal degradation stabilities in the materials with higher degrees of saturation. POLYM. ENG. SCI., 54:2332–2344, 2014. © 2013 Society of Plastics Engineers     

Synthesis of poly(aryl ether sulfone)‐graft‐polystyrene and poly(aryl ether sulfone)‐graft‐[polystyrene‐block‐poly(methyl methacrylate)] through atom transfer radical polymerization

A new graft copolymers poly(aryl ether sulfone)‐graft‐polystyrene (PSF‐g‐PS) and poly(aryl ether sulfone)‐graft‐[polystyrene‐block‐poly(methyl methacrylate)] (PSF‐g‐(PS‐b‐PMMA)) were successfully prepared via atom transfer radical polymerisation (ATRP) catalyzed by FeCl₂/isophthalic acid in N,N‐dimethyl formamide. The products were characterized by GPC, DSC, IR, TGA and NMR. The characterization data indicated that the graft copolymerization was accomplished via conventional ATRP mechanism. The effect of chloride content of the macroinitiator on the graft copolymerization was investigated. Only one glass transition temperature (T_g) was detected by DSC for the graft copolymer PSF‐g‐PS and two glass transition temperatures were observed in the DSC curve of PSF‐g‐(PS‐b‐PMMA). The presence of PSF in PSF‐b‐PS or PSF‐g‐(PS‐b‐PMMA) was found to improve thermal stabilities. © 2002 Society of Chemical Industry     

Synthesis and characterization of PBMA‐b‐PSt‐b‐PBMA triblock copolymers by atom transfer radical emulsion polymerization

Poly(n‐butyl methacrylate)‐b‐polystyrene‐b‐poly(n‐butyl methacrylate) (PBMA‐b‐PSt‐b‐PBMA) triblock copolymers were successfully synthesized by emulsion atom transfer radical polymerization (ATRP). Difunctional polystyrene (PSt) macroinitiators that contained alkyl chloride end‐groups were prepared by ATRP of styrene (St) with CCl₄ as initiator and were used to initiate the ATRP of butyl methacrylate (BMA). The latter procedure was carried out at 85°C with CuCl/4,4′‐di (5‐nonyl)‐2,2′‐bipyridine (dNbpy) as catalyst and polyoxyethylene (23) lauryl ether (Brij35) as surfactant. Using this technique, triblock copolymers consisting of a PSt center block and PBMA terminal blocks were synthesized. The polymerization was nearly controlled, ATRP of St from those macroinitiators showed linear increases in the number average molecular weight (Mn) with conversion. The block copolymers were characterized with infrared (IR) spectroscopy, hydrogen‐1 nuclear magnetic resonance (¹HNMR), and differential scanning calorimetry (DSC). The effects of the molecular weight of macroinitiators, concentration of macroinitiator, catalyst, emulsion, and temperature on the polymerization were also investigated. Thermodynamic data and activation parameters for the ATRP were also reported. POLYM. ENG. SCI., 45:1508–1514, 2005. © 2005 Society of Plastics Engineers     

Synthesis of graft copolymers. II. Synthesis of polystyrene‐g‐poly(methyl methacrylate)

The thermolysis of labile 1,2‐bis(trimethylsilyloxy)tetraphenylethane groups pendant along polystyrene chains in the presence of various vinyl monomers leads to the direct synthesis of graft copolymers. Depending on the monomer chosen, the polymerization temperature, and the number of active sites by the macroinitiator molecule, crosslinked or total soluble graft copolymers can be prepared. Several conditions were studied in order to attain soluble polystyrene‐g‐poly(methyl methacrylate) copolymers under a controlled polymerization mechanism. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 12–18, 2002     

Synthesis of PMMA‐PTHF‐PMMA and PMMA‐PTHF‐PST linear and star block copolymers

Combination of cationic, redox free radical, and thermal free radical polymerizations was performed to obtain linear and star polytetramethylene oxide (poly‐THF)‐polymethyl methacrylate (PMMA)/polystyrene (PSt) multiblock copolymers. Cationic polymerization of THF was initiated by the mixture of AgSbF₆ and bis(4,4′ bromo‐methyl benzoyl) peroxide (BBP) or bis (3,5,3′,5′ dibromomethyl benzoyl) peroxide (BDBP) at 20°C to obtain linear and star poly‐THF initiators with M_w varying from 7,500 to 59,000 Da. Poly‐THF samples with hydroxyl ends were used in the methyl methacrylate (MMA) polymerization in the presence of Ce(IV) salt at 40°C to obtain poly(THF‐b‐MMA) block copolymers containing the peroxide group in the middle. Poly(MMA‐b‐THF) linear and star block copolymers having the peroxide group in the chain were used in the polymerization of methyl methacrylate (MMA) and styrene (St) at 80°C to obtain PMMA‐b‐PTHF‐b‐PMMA and PMMA‐b‐PTHF‐b‐PSt linear and star multiblock copolymers. Polymers obtained were characterizated by GPC, FT‐IR, DSC, TGA, ¹H‐NMR, and ¹³C‐NMR techniques and the fractional precipitation method. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 219–226, 2004     

Controlled/living RAFT polymerization of N‐phenyl maleimide and synthesis of its block copolymers

The controlled/living radical polymerization of N‐phenyl maleimide (NPMI) was achieved using 2,2′‐azobisisobutyronitrile as the initiator and 2‐cyanopropyl‐2‐yl dithiobenzoate as the reversible addition‐fragmentation chain transfer agent at 75°C in dichloroethane/ethylene carbonate (60/40, w/w) mixed solvent. The block copolymers of polystyrene‐b‐polyNPMI and poly(n‐butyl methacrylate)‐b‐polyNPMI were successfully prepared by chain extension from dithiobenzoate‐terminated polystyrene and poly (n‐butyl methacrylate) to NPMI, respectively. The obtained NPMI‐based (co)polymers were characterized by gel permeation chromatography and ¹H‐NMR spectroscopy. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of functionalized syndiotactic polystyrene copolymers

Functionalized syndiotactic polystyrene copolymers were synthesized and characterized. The syndiotactic polystyrene copolymers, poly(styrene‐co‐4‐methylstyrene) (sPSMS), were prepared by styrene with 4‐methylstyrene with a metallocene/methylaluminoxane catalyst. In addition, grafted copolymers, chemically grafted with isoprene onto an sPSMS backbone [poly(styrene‐co‐4‐methylstyrene)‐g‐polyisoprene (sPSMS‐g‐PIP)] were synthesized by anionic grafting polymerization with a metallation reagent. In this study, we also examined the effect of the degree of functionalization (epoxidation) on the polymer structure of the sPSMS‐g‐PIP copolymers. Experimental results indicate that the crystallinity of the sPSMS‐g‐PIP copolymer was lower than that of the ungrafted sPSMS copolymer. Moreover, the epoxy‐containing sPSMS‐g‐PIP copolymer effectively increased the thermal stability more than did the sPSMS‐g‐PIP copolymer alone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1038–1045, 2002     

Novel polyisobutylene stars. XXIII. Thermal,mechanical, and processing characteristics of poly(phenylene ether)/polydivinylbenzene(polyisobutylene‐b‐polystyrene)37 blends

The objective of these investigations was to increase the use temperature of novel star‐block polymers consisting of a crosslinked polydivinylbenzene (PDVB) core from which radiate multiple poly(isobutylene‐b‐polystyrene) (PIB‐b‐PSt) arms, abbreviated by PDVB(PIB‐b‐PSt)_n. We achieved this objective by blending star‐blocks with poly(phenylene oxide) (PPO) that is miscible with PSt. Thus, various PPO/PDVB(PIB‐b‐PSt)_n blends were prepared, and their thermal, mechanical, and processing properties were investigated. The hard‐phase glass‐transition temperature of the blends could be controlled by the amount (wt %) of PPO. The blends displayed superior retention of tensile strengths at high temperatures as compared to star blocks. The melt viscosities of blends with low weight percentages of PPO were lower than those of star blocks. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2866–2872, 2002     

Synthesis and characterization of four‐arm star‐shaped polymers and copolymers

Four‐arm star‐shaped polymers and copolymers were obtained by transition metal‐catalyzed atom‐transfer radical polymerization (ATRP). The polymers were characterized by FTIR and ¹H‐NMR spectroscopy. Gel permeation chromatography results indicated the formation of polystyrene and polystyrene‐block‐poly(methyl methacrylate) (PS‐b‐PMMA) arms with controlled molecular weights. In dilute solution, the linear polymers had higher inherent viscosities than star‐shaped ones. Thermogravimetric analysis showed a similar degradation mechanism for linear and star‐shaped polymers. Differential scanning calorimetry indicated the successful formation of diblock star‐shaped copolymers. Copyright © 2006 Society of Chemical Industry     

Synthesis of poly(octadecyl acrylate‐b‐styrene‐b‐octadecyl acrylate) triblock copolymer by atom transfer radical polymerization

The synthesis of triblock copolymer poly(octadecyl acrylate‐b‐styrene‐b‐octadecyl acrylate), using atom transfer radical polymerization (ATRP), is reported. The copolymers were prepared in two steps. First, polystyrene was synthesized by ATRP using α,α′‐dichloro‐p‐xylene/CuBr/bpy as the initiating system; Second, polystyrene was further used as macroinitiator for the ATRP of octadecyl acrylate to prepare ABA triblock copolymers in the presence of FeCl₂·4H₂O/PPh₃ in toluene. Polymers with controlled molecular weight (M_n = 17,000–23,400) and low polydispersity index value (1.33–1.44) were obtained. The relationship between molecular weight versus conversion showed a straight line. The effect of reaction temperature on polymerization was also investigated, showing a faster polymerization rate under higher temperature. The copolymers were characterized by FTIR, ¹H‐NMR, DSC, and GPC and the crystallization behavior of the copolymers was also studied. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1539–1545, 2004