Flow behaviour and microstructure evolution in novel SiO2/PP/LCP ternary composites: effects of filler properties and mixing sequence

When silica (SiO₂) fillers were introduced into the polypropylene (PP) and liquid‐crystalline polymer (LCP) blend, it was found that the mixing sequence, the filler size, and the filler surface nature affected the rheology of the composites and the morphology of the LCP phase in the ternary composite. In particular, the compatibility between the filler and the PP matrix was found to exert a strong influence on the droplet‐fibril transition. The incorporation of the hydrophobic silica to the LCP/PP blend facilitated the fibrillation of LCP because the hydrophobic filler demonstrated affinity towards the hydrophobic PP matrix. The preferential residence of the hydrophobic silica in the PP phase would minimise the LCP domain disruption leading to the formation of LCP fibrils with high aspect ratios. The use of fine filler and in situ blending, which promoted the filler–LCP interaction, could prevent coalescence, inhibit deformation and hinder fibril development as well. © 2003 Society of Chemical Industry     

Enhanced fibrillation of LCP by CaCO3 whisker in polysulfone matrix through increasing elongational stress

Induced by different fillers, various hydrodynamic effects enhance the fibrillation of liquid crystalline polymer (LCP) in in situ hybrid composites. Through choosing CaCO₃ whisker as the filler and polysulfone (PSF) as the matrix, the effect of the filler size and the affinity between components on the morphological evolution of LCP droplets has been investigated. In contrast to the spherical or ellipsoidal droplets of LCP formed in binary PSF/LCP blends, the fibrillation of LCP was promoted by the introduction of whisker particles in all ternary blends at shear rates studied. The analysis of the flow field indicated that the predominant factors promoting the fibrillation of LCP were the vortex enhanced and elongational stress increased by the whisker in the converging flow area at the entrance of capillary, rather than the viscosity ratio and capillary number.     

Energy‐based predictive criterion for LCP fibrillation in LCP/thermoplastic polymer blends under shear

This article relates the fibrillation of liquid crystalline polymer (LCP) under shear in its blend with a thermoplastic polymer (TP) to the relative rate of energy utilization in the LCP and TP phases. The development of a criterion based on the energy relationship for predicting LCP fibrillation in the blend is discussed. The formation of LCP fibers in the blends of LCP with polycarbonate (PC), polyethylene naphthalate (PEN), high‐density polyethylene (HDPE), polypropylene (PP), and silica‐filled polypropylene (PP) was studied to validate the criterion and to demonstrate its applicability. For all the blends, viscosity data were obtained by using a capillary rheometer, which was subsequently used to estimate the rate of energy utilization in the LCP and the matrix phases. The predictions based on the proposed criterion were verified through the morphological investigations carried out on the extrudates obtained from the same capillary experiments. The energy‐based criterion was easy to implement, could account for the effect of variable LCP concentration and fillers in the blend, and could provide reliable predictions for a variety of LCP/TP blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3314–3324, 2003     

Effect of nano‐silica filler on the rheological and morphological properties of polypropylene/liquid‐crystalline polymer blends

A fumed hydrophilic nano‐silica‐filled polypropylene (PP) composite was blended with a liquid‐crystalline polymer (LCP; Rodrun LC5000). The preblended polymer blend was extruded through a capillary die; this was followed by a series of rheological and morphological characterizations. The viscosity of the PP matrix increased with the addition of the hydrophilic nano‐silica. At shear rates between 50 and 200 s^?1, the composite displays marked shear‐thinning characteristics. However, the incorporation of LC5000 in the PP composite eliminated the shear‐thinning characteristic, which suggests that LC5000 destroyed the agglomerated nano‐silica network in the PP matrix. Although the viscosity ratio of LCP/PP was reduced after the addition of nano‐silica fillers, the LCP phases existed as droplets and ellipsoids. The nano‐silicas were concentrated in the LC5000 phase, which hindered the formation of LCP fibers when processed at high shear deformation. We carried out surface modification of the hydrophilic nano‐silica to investigate the effect of modified nano‐silica (M‐silica) on the morphology of the PP/LC5000 blend system. Ethanol was successfully grafted onto the nano‐silica surface with a controlled grafting ratio. The viscosity was reduced for PP filled with ethanol‐M‐silica when compared to the system filled with untreated hydrophilic nano‐silica. The LC5000 in the (PP/M‐silica)/LC5000 blend existed mainly in the form of fibrils. At high shear rates (e.g., 3000 s^?1), the LC5000 fibril network was formed at the skin region of the extrudates. The exclusion of nano‐silica in the LC5000 phase and the increased viscosity of the matrix were responsible for the morphological changes of the LCP phase. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1484–1492, 2003     

热致性液晶与聚丙烯原位复合材料的相容性研究

在热致液晶共聚酯（ＬＣＰ）与聚丙烯（ＰＰ）的共混体系中引入相容剂（接枝共聚物ＭＡＨ—ｇ－ＰＰ），借助热台偏光显微镜、扫描电镜、差示扫描量热仪、流变仪等方法研究了相容剂对ＰＰ／ＬＣＰ原位复合材料的微观结构和界面性能、结晶行为、流变行为以及力学性能的影响．结果表明：添加相容剂后，基体中的ＬＣＰ微纤分散更均匀，ＬＣＰ微纤长径比Ｌ／Ｄ增大．ＰＰ和ＬＣＰ两相之间有较好的粘连，促进了共混体的结晶，改善了ＰＰ／ＬＣＰ原位复合材料的力学性能．     

Self-reinforced polypropylene/LCP prepregs and laminates

Polypropylenes (PPs) of various molecular weights were mixed with a thermotropic liquid crystal polymer (LCP) to prepare unidirectional sheets (prepregs), quasi-isotropic and unidirectional laminates. The mechanical properties and the morphology of the prepregs and the laminates at 0° and 90° with respect to the machine direction were investigated as a function of draw ratio, LCP concentration and molecular weight of the PP. The results for prepregs and laminates showed that both drawing and LCP concentration generally enhanced modulus and tensile strength in machine direction. The morphology of LCP changed from spherical or ellipsoidal droplets to elongated fibrils as the draw ratio increased. The diameter of LCP fibrils decreased with increasing molecular weight of the PP matrix, indicating more effective droplet breakup and better mixing in the case of high molecular weight PP.     

Self‐reinforced polypropylene/LCP extruded strands and their moldings

Polypropylenes (PP) of various molecular weights were mixed with a thermotropic liquid crystal polymer (LCP) and strands were prepared by extrusion and stretching. The strands were subsequently pelletized and then injection molded at temperatures below the melting point of LCP. The mechanical properties and the morphology of the strands and injection‐molded specimens were investigated as a function of draw ratio, LCP concentration, and PP molecular weight. The results for strands show that an increase in the draw ratio, LCP concentration and matrix molecular weight in general enhance the modulus and tensile strength. However, the tensile properties of injection‐molded specimens are found to be reduced compared with those of the original strands, in particular at high LCP concentration. The morphology of LCP changes from spherical or ellipsoidal droplets to elongated fibrils in the strands as the draw ratio increases, but this aligned LCP fibrillar morphology was not transferred to the injection‐molded specimens because of the disorientation of fibrils during injection molding. Compatibilization of PP/LCP blends was also studied by using various polymers. Maleic anhydride and acrylic acid modified PPs improved the tensile properties modestly, but maleic anhydride modified EPDM reduced the tensile properties.     

Fibrillation of liquid crystalline polymer in polysulfone promoted by increased system elasticity via adding nano-silica

Ternary blends composed of a liquid crystalline polymer (LCP), nano-SiO₂ and polysulfone (PSF) were prepared by melt blending. Very long and perfectly oriented LCP fibrils were in situ formed in capillary flows by adding 5 vol% of nano-SiO₂ to binary PSF/LCP blend. Dynamic rheology analysis indicated that the sharp increase of elasticity was caused by higher content of nano-SiO₂. Then the entrance angle was decreased and elongational stress increased when the polymer melt flowed through the abrupt contraction, which resulted in the fibrillation of LCP in PSF/LCP/nano-SiO₂ system.     

Rheological hybrid effect in dually filled polycarbonate melt containing liquid crystalline polymer

Polycarbonate (PC)/liquid crystalline polymer (LCP) blends dually filled with glass fiber and nano‐SiO₂ were prepared by melt blending, with the use of a commercial Vectra A130 as the source of LCP and glass fiber. In these dually filled PC/LCP melts, rheological hybrid effect occurred, confirmed by the melt viscosity of the quadruple polymer blends decreased with increasing nano‐silica loading, influenced by the minor LCP phase in the blend. The drastic viscosity reduction closely correlates with the deformation and fibrillation of LCP droplets in the system. The LCP fibrillation was controlled jointly by the thermodynamic and hydrodynamic driving forces. Finally, the dually filled PC/LCP melt had decreased viscosity lower than those of pure PC, silica‐filled PC, and PC/Vectra A130 blends, and furthermore had decreased glass fiber breakage, shown by larger average aspect ratio than that in PC/Vectra A130 blends. POLYM. ENG. SCI., 2012. © 2011 Society of Plastics Engineers     

In situ reactive compatibilized noryl/LCP blends

This article reveals that the already known improved properties of the thermoplastic–liquid crystalline polymer (LCP) blends can be further improved substantially over the corresponding noncompatibilized counterparts by using a reactive in situ type compatibilizer, the styrene–glycidyl methacrylate (SG) copolymer. This SG copolymer has been demonstrated in this article to be an effective reactive compatibilizer to improve the processability, heat deflection temperature, and mechanical properties of Noryl/LCP blends. The epoxy functional groups of the SG copolymer can react with the end groups of PPO (in Noryl) and LCP. The in situ-formed SG–g–LCP copolymer tends to reside along the interface of Noryl–LCP and reduces the interfacial tension during melt processing. The resultant LCP fibers in the Noryl matrix of the compatibilized blends have a higher aspect ratio because the fibers become finer, longer, and tend to form lamellate domains with a greater interphase contact area than those from the noncompatibilized blends. The compatibilized blends also improve the interphase adhesion between Noryl and LCP. The presence of ethyl triphenylphosphonium bromide catalyst promotes the grafting reaction to improve blend compatibilization. © 1995 John Wiley & Sons, Inc.     

Effect of ethylene/propylene ratio on reinforcing characteristics of liquid crystalline polymer (LCP) in EPDM-LCP composites

Abstract

Two ethylene/propylene diene monomer (EPDM) polymers were blended with a liquid crystalline polymer (LCP) at concentrations of 10, 20, 30 and 40 wt-%. The effects of ethylene/propylene (EP) ratio on the in situ fibrillation, and hence the reinforcing characteristics, of the LCP in EPDM-LCP blends were studied. The fibre forming capacity of the LCP depended on the viscosity of the EPDM rubber. Under high temperature processing conditions (at 300°C), the high EP ratio EPDM, which had the higher viscosity, facilitated the fibrillation of the LCP. Further melt processing at 100°C, followed by curing at 150°C, decreased the reinforcing effects of the LCP owing to breakage of the fibrils under the high shear stresses developed in the high viscosity matrix. However, this degradation of fibre lengths depended on the LCP concentration. After curing, the more viscous EPDM formed blends with higher stiffnesses and strengths than those obtained from the low viscosity EPDM. Both the nucleation and growth of crystal domains in the EPDM matrix were promoted by small amounts of LCP. Again the effects were more pronounced in the EPDM with the higher EP ratio.     

Rheology and impact characteristics of compatibilized polypropylene-liquid crystalline polymer composites

Polypropylene-liquid crystalline polymer (PP/LCP) and maleic anhydride compatibilized PP/LCP blends were prepared using the extrusion technique followed by injection molding. The LCP employed was Vectra A950 which consists of 25 mol % of 2,6-hydroxynaphthoic acid and 75 mol % of p-hydroxybenzoic acid. The rheology, morphology, and impact behavior of compatibilized PP/LCP blends were investigated. The rheological measurements showed that the viscosity of LCP is significantly higher than that of the PP at 280°C. This implied that the viscosity ratio of the LCP to the polymer matrix is much larger than unity. Scanning electron microscopy (SEM) observations revealed that the LCP domains are dispersed mainly into elongated ellipsoids in the PP/LCP blends. However, fine fibrils with large aspect ratios were formed in the compatibilized PP/LCP blends containing LCP content ≥ 10 wt %. The development of fine fibrillar morphology in the compatibilized PP/LCP blends had a large influence on the mechanical properties. The Izod impact strength of the PP/LCP blends showed little dependence on the LCP concentrations. On the other hand, the impact strength of the compatibilized PP/LCP blends was dependent on the LCP concentrations. The correlation between the LCP fibrillar morphology and spherulitic structure with the impact properties of the compatibilized PP/LCP blends is discussed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 521–530, 1998     

Comparison of mechanical properties of PP/SEBS blends at intermediate and high strain rates with SiO2 nanoparticles vs. CaCO3 fillers

The present article focuses on the effect of two types of inorganic fillers (SiO₂ and CaCO₃) on the mechanical properties of PP/SEBS blend. The nominal particle diameters of SiO₂ and CaCO₃ are 7 nm and 1 μm, respectively. The studied blend ratios were PP/SEBS/SiO₂ (CaCO₃) = 75/22/3 and 73/21/6 vol %. The morphology of polymer blends was observed and the distributions of the SEBS, SiO₂, and CaCO₃ particles were analyzed by transmission electron microscopy (TEM). Tensile tests were conducted at nominal strain rates from 3 × 10^?1 to 10² s^?1. The apparent elastic modulus has the local strain‐rate dependency caused by SiO₂ nanoparticles around SEBS particles in the blend of PP/SEBS/SiO₂. The yield stress has weak dependency of morphology. The absorbed strain energy has strong dependency of the location of SiO₂ nanoparticle or CaCO₃ fillers and SEBS particle in the morphology. It is considered that such morphology, in which inorganic nanoparticles are located around SEBS particles, can prevent the brittle fracture while the increased local strain rate can enhance the apparent elastic modulus of the blend at the high strain rate. On the basis of the results of this study, the location and size of inorganic nanoparticles are the most important parameters to increase the elastic modulus without decreasing the material ductility of the blend at both low and high strain rates. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Factors influencing microstructure formation in polyblends containing liquid crystalline polymers

Four isotropic polymers, poly(butylene terephthalate) (PBT), polycarbonate (PC), polyethersulfone (PES) and polysulfone (PSU), were blended by extrusion with a thermotropic liquid crystalline polymer (LCP) at different temperatures. The morphology of extrudates was observed by means of scanning electron microscopy and the intrinsic aspect ratio of LCP fibrils and particles separated from matrix resin was measured with an image analysis. Special attention was paid to the LCP fibrillation in these four matrices in a wide temperature range from 270 to 360°C and the internal relations among the effects of processing parameters, such as viscosity ratio, extrusion temperature, and LCP concentration. The results show that the viscosity ratio of the dispersed LCP phase to the continuous phase is a decisive factor determining the formation of LCP fibrils, but its effect closely relates with the LCP content. In the range of viscosity ratios investigated, 0.004 to 6.9, and lower LCP content of 10%, significant fibrillation took place only at viscosity ratios below 0.01. It is predicted that the upper limit of the viscosity ratio for LCP fibrillation will increase with increasing LCP content. A comparison of the morphologies of LCP/PES blends with different LCP concentrations reveals that the LCP phase becomes continuous at a concentration of less than 50%, and high LCP content does not always favor the formation of long and uniform LCP fibrils. The extrusion temperature has a marked effect on the size of the minor LCP domains. For fibril forming systems, the percentage of LCP fibrils with larger aspect ratios increases with increasing extrusion temperatures. All these results are explained by the combined role of deformation and coalescence of the LCP disperesed phase in the blend.     

The effect of the viscosity ratio of dispersed phase to matrix on the rheological,morphological, and mechanical properties of polymer blends containing a LCP

The effect of the viscosity ratio of the dispersed LCP phase to the polystyrene/poly(phenylene oxide) (PS/PPO) thermoplastic matrix on the rheological, morphological, and resultant mechanical properties of the LCP blends was investigated. The viscosity of PS/PPO is largely dependent on the blend composition, so that different levels of viscosity ratios of dispersed LCP phase to PS/PPO thermoplastic matrix are obtained by using PS/PPO premixtures of different blend ratios as a thermoplastic matrix. When the viscosity of the LCP dispersed phase is lower than that of the thermoplastic matrix, finely distributed fibril structure of LCP is obtained. Tensile modulus of injection molded specimens show a positive deviation from the additive rule when the viscosity ratio (η_LCP/η_matrix) is smaller than unity. These improvements in tensile modulus are attributed to the formation of finely distributed LCP fibrils. © 1996 John Wiley & Sons, Inc.     

Synthesis of PP–LCP graft copolymers and their compatibilizing activity for PP/LCP blends

The aim of this work was the synthesis of new graft copolymers consisting of polypropylene (PP) backbones and liquid crystalline polymer (LCP) branches, to be used as compatibilizing agents for PP/LCP blends. The PP-g-LCP copolymers have been prepared by polycondensation of the monomers of a semiflexible liquid crystalline polyester (SBH 1 : 1 : 2), that is, sebacic acid (S), 4,4′-dihydroxybiphenyl (B), and 4-hydroxybenzoic acid (H) in the mole ratio of 1 : 1 : 2, carried out in the presence of appropriate amounts of a commercial acrylic-acid-functionalized polypropylene (PPAA). The polycondensation products, referred to as COPP50 and COPP70, having a calculated PPAA concentration of 50 and 70 wt %, respectively, have been fractionated with boiling toluene and xylene, and the soluble and insoluble fractions have been characterized by Fourier transform infrared and nuclear magnetic resonance spectroscopy, scanning electron microscopy (SEM), differential scanning calorimetry, and X-ray diffraction. All analytical characterizations have concordantly shown that the products are formed by intricate mixtures of unreacted PPAA and SBH together with PP-g-SBH copolymers of different composition. Exploratory experiments carried out by adding small amounts of COPP50 or COPP70 into binary mixtures of isotactic polypropylene (iPP) and SBH while blending have demonstrated that this practice leads to an appreciable improvement of the dispersion of the minor LCP phase, as well as to an increase of the crystallization rate of iPP. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 391–403, 1998     

Mechanical properties and morphologies of PP/mPE/filler composites

Because of the poor impact behavior of polypropylene (PP) at low temperatures, the blending of PP with metallocene‐polymerized polyethylene (mPE) elastomers was investigated in this study. However, a reduced modulus of the overall blend was inevitable because of the addition to elastomers. To obtain a balance of the properties, we introduced rigid inorganic fillers to PP/mPE blends. The performance of the composites was characterized with tensile and Charpy notched impact tests, and the fracture morphology was examined with scanning electron microscopy. The results showed that the effects of fillers in a brittle matrix and in a ductile matrix were quantitatively different. For PP/mPE/filler ternary composites, the dependence of Young's modulus and yield strength on CaCO₃ content was not significant compared with that of PP/filler binary composites, whereas the elongation at break and tensile toughness at room temperature for PP/mPE/filler systems were more improved. The impact strength of the PP/mPE blends filled with untreated glass beads and CaCO₃ at a low temperature was lowered because of the weak interfacial bond. However, the values of the impact strength of the PP/mPE/filler composites at a low temperature remained at a high level compared with that of pure PP. In particular, a PP/mPE blend filled with surface‐treated kaolin had a higher low‐temperature impact toughness than the unfilled blend. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 3029–3035, 2002; DOI 10.1002/app.2333     

Mechanical properties and morphology of LCP/ABS blends compatibilized with a styrene–maleic anhydride copolymer

A co‐polyester liquid crystalline polymer (LCP) was melt blended with an acrylonitrile–butadiene–styrene copolymer (ABS). LCP fibrils are formed and a distinct skin/core morphology is observed in the injection moulded samples. At higher LCP concentration (50 wt%), phase inversion occurs, where the dispersed LCP phase becomes a co‐continuous phase. While the tensile strength and Young's modulus remain unchanged with increasing LCP content up to 30 wt% LCP, a significant enhancement of the modulus at 50 wt% LCP is observed due to the formation of co‐continuous morphology. The blend modulus is lower than the values predicted by the rule of mixtures, suggesting a poor interface between the LCP droplets and ABS matrix. A copolymer of styrene and maleic anhydride (SMA) was added in the LCP/ABS blends during melt blending. It is observed that SMA has a compatibilizing effect on the blend system and an optimum SMA content exists for mechanical properties enhancement. SMA improves the interfacial adhesion, whereas excess of SMA reduces the LCP fibrillation. Copyright © 2003 Society of Chemical Industry     

Effects of shear rate,viscosity ratio and liquid crystalline polymer content on morphological and mechanical properties of polycarbonate and LCP blends

Studies were conducted on the effects of shear rate, viscosity ratio and liquid crystalline polymer (LCP) content on the morphological and mechanical properties of polycarbonate (PC) and LCP blends. The LCP (LC5000) used was a thermotropic liquid crystalline polymer consisting of 80/20 of parahydroxybenzoic acid and poly(ethylene terephthalate) (PHB/PET). The viscosity ratio (viscosity of LCP: viscosity of matrix) was varied by using two processing temperatures. Due to the different sensitivity of materials to temperature, variation in the processing temperature will lead to varying viscosity of the components in the blends. Based on this principle, the processing temperature could be manipulated to provide a favourable viscosity ratio of below unity for fibre formation. To study the effect of shear rate, the flow rate of the blend and the mould thickness were varied. The shear rate has a significant effect on the fibrillation of the LCP phase. The effect was more prominent when the viscosity ratio was low and the matrix viscosity was high. At 5 wt% LCP, fibrillation did not occur even at low viscosity ratios and high shear rates. It was also observed that the LCP content must be sufficiently high to allow coalescence of the dispersed phase for subsequent fibrillation to occur. © 2002 Society of Chemical Industry     

In situ compatibilized SAN/LCP blends through reactive copolymers

Styrene–acrylonitrile–glycidyl methacrylate (SAG) copolymers with various contents of glycidyl methacrylate (GMA) were used to compatibilize the incompatible blends of styrene–acrylonitrile (SAN) and a liquid crystalline polymer (LCP). These SAG copolymers contain reactive glycidyl groups that are able to react with the carboxylic acid and/or hydroxyl end groups of the LCP to form the SAG‐g‐LCP copolymers during melt processing. The in situ–formed graft copolymers tend to reside along the interface to reduce the interfacial tension and to increase the interface adhesion. The morphologies of the SAN/LCP blends were examined by using scanning electron microscopy (SEM), where the compatibilized SAN/LCP blends were observed with greater numbers and finer fibrils than those of the corresponding uncompatibilized blends. The mechanical properties of the blends increased after compatibilization. The presence of a small amount (200 ppm) of ethyl triphenylphosphonium bromide (ETPB) catalyst further promotes the graft reaction and improves the compatibilization. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3321–3332, 2001