Radiation effects on LDPE/EVA blends

Radiation effects of low‐density polyethylene/ethylene‐vinyl acetate copolymer (LDPE/EVA) blends were discussed. EVA content in the LDPE/EVA blends was an enhancement effect on radiation crosslinking of LDPE/EVA blends, and the highest radiation crosslinking was obtained when the EVA content was reached at 30% when irradiated by γ‐ray in air. The phenomenon was discussed with the compatibility, morphology, and thermal properties of LDPE/EVA blends and found that the enhanced radiation crosslinking of the LDPE/EVA blends was proportional to the good compatibility, the increasing degree of the amorphous region's content of the LDPE/EVA blends, and the vinyl acetate content of EVA. We also found that the vinyl acetate of EVA in the blends is easily oxidized by γ‐ray irradiation in air. The possible radiation crosslinking and degradation mechanism of LDPE/EVA blends was discussed quantitatively with a novel method “step‐analysis” process of irradiated LDPE/EVA blends in the thermal gravimetric analysis (TGA) technique. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1296–1302, 2002     

Radiation effects on poly(propylene) (PP)/ethylene–vinyl acetate copolymer (EVA) blends

Radiation effects on poly(propylene)/ethylene–vinyl acetate copolymer (PP/EVA) blends are discussed. Increasing the EVA content enhanced the crosslinking effect of radiation in PP/EVA blends. This effect was significant when the EVA content was ≥50% in PP/EVA blends that were exposed to γ‐ray irradiation in air. This phenomenon is discussed in relation to the compatibility, morphology, and thermal properties of PP/EVA blends. The results indicate that the effect is dependent on the compatibility, the increase in the amorphous region content, and the EVA content in PP/EVA blends. The possible mechanism of radiation crosslinking or degradation in irradiated PP/EVA blends was studied quantitatively by a novel method, a “step analysis” process, and thermal gravimetric analysis. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3420–3424, 2002     

Thermal and mechanical properties of uncrosslinked and chemically crosslinked polyethylene/ethylene vinyl acetate copolymer blends

Uncrosslinked and chemically crosslinked binary blends of low‐ and high‐density polyethylene (PE), with ethylene vinyl acetate copolymer (EVA), were prepared by a melt‐mixing process using 0–3 wt % tert‐butyl cumyl peroxide (BCUP). The uncrosslinked blends revealed two distinct unchanged melting peaks corresponding to the individual components of the blends, but with a reduced overall degree of crystallinity. The crosslinking further reduced crystallinity, but enhanced compatibility between EVA and polyethylene, with LDPE being more compatible than HDPE. Blended with 20 wt % EVA, the EVA melting peak was almost disappeared after the addition of BCUP, and only the corresponding PE melting point was observed at a lowered temperature. But blended with 40% EVA, two peaks still existed with a slight shift toward lower temperatures. Changes of mechanical properties with blending ratio, crosslinking, and temperature had been dominated by the extent of crystallinity, crosslinking degree, and morphology of the blend. A good correlation was observed between elongation‐at‐break and morphological properties. The blends with higher level of compatibility showed less deviation from the additive rule of mixtures. The deviation became more pronounced for HDPE/EVA blends in the phase inversion region, while an opposite trend was observed for LDPE/EVA blends with co‐continuous morphology. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3261–3270, 2007     

Influence of crosslinking on crystallization,rheological, and mechanical behaviors of high density polyethylene/ethylene‐vinyl acetate copolymer blends

High density polyethylene (HDPE)/ethylene‐vinyl acetate copolymer (EVA) blends with selective crosslinking the EVA phase were prepared and the crystallization, rheological, and mechanical behaviors were studied. Selective crosslinking of EVA component could greatly improve both tensile and impact strengths of the HDPE‐rich blends and influence melting enthalpy at different annealing temperature in successive self‐nucleation and annealing procedure. Dynamic mechanical analysis reveals that glass transition temperatures of both the HDPE and EVA components are lowered upon blending and are raised upon crosslinking. The uncrosslinked HDPE/EVA blends are unstable in the melt and show increment in storage modulus (G′) and decay in loss tangent (tanδ) with annealing time associated with phase coarsening. However, morphology of selectively crosslinked blends in the melt state is highly unstable, characterized by a fast migration of uncrosslinked HDPE component out of the crosslinked EVA phase to the surface resulting in a rapid decay in G′ and an increment in tanδ at the early stage of annealing. POLYM. ENG. SCI., 54:2848–2858, 2014. © 2014 Society of Plastics Engineers     

Double‐yielding behavior in injection‐molded polycarbonate/high‐density polyethylene/ethylene–vinyl acetate copolymer blends

A uniaxial tensile test was performed for polycarbonate (PC)/high‐density polyethylene (HDPE)/ethylene–vinyl acetate copolymer (EVA) blends with a fixed EVA content but various PC contents. The double‐yielding phenomenon and its composition dependence, as observed in the PC/HDPE blend, were again detected. EVA did not serve as a successful compatibilizer of PC and HDPE in the PC/HDPE/EVA blend. The incorporation of EVA resulted in a larger size and a more irregular shape of the PC fibers, as indicated in the scanning electron microscope observations; this, consequently, produced a higher serious stress concentration in the blend. This more complicated and instable morphology produced different double‐yielding behaviors in the PC/HDPE/EVA blends compared with the binary one. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effects of high‐energy electron beam on low‐density polyethylene materials containing EVA

A series of low‐density polyethylene (LDPE) blends with different amounts of ethylene–vinyl–acetate (EVA) was prepared and irradiated with 10 MeV electron beam in the range of 0–250 kGy at room temperature in air. EVA was used as a compatibilizer and softener in four different amounts: 5, 10, 20, and 30 wt %, based on polyethylene (PE). The crosslinking of the samples was studied on the basis of gel‐content measurements as well as some thermal and mechanical properties of the specimens. The results indicated that the LDPE and LDPE–EVA blends could be crosslinked by a high‐energy electron beam, of which their thermal and mechanical properties changed effectively, however, because of EVA content of the polymer; the blends were more sensitive to lower doses of radiation. These studies were carried out to obtain a suitable compound for heat‐shrinkable tubes. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1049–1052, 2004     

Processability and thermal properties of blends of high density polyethylene,poly (ethylene terephthalate), and ethyl vinyl acetate compatibilizer

Because of differences in chemical structure and rheological characteristics, high density polyethylene (HDPE) and poly(ethylene terephthalate) (PET) are incompatible when blended during recycling of PET soft drink bottles. To improve the properties of the blends, ethylene vinyl acetate copolymer (EVA) was used as a compatibilizer. Based on torque rheometer tests, the higher the concentration of PET in the blends, the higher the initial loading torque. Blends of 50% HDPE and 50% PET had the lowest equilibrium torque. Equilibrium torque was highest at 5% EVA. The presence of EVA made only a slight difference in the glass transition temperatures of HDPE/PET blends. Higher EVA content in the blend resulted in a lower melting endotherm. Thermogravimetric analysis showed that thermal stability was independent of EVA content; but the more PET in the blend, the lower the final weight loss.     

High‐performance antistatic ethylene–vinyl acetate copolymer/high‐density polyethylene composites with graphene nanoplatelets coated by polyaniline

Graphene nanoplatelets coated by polyaniline (GNP@PANI) and ethylene–vinyl acetate (EVA) copolymer–high‐density polyethylene (HDPE) were used for the first time to prepare high‐performance antistatic composites through an effective method that combined solution mixing and melt blending. GNP@PANI nanocomposites were fabricated by in situ polymerization to improve the dispersion of graphene nanoplatelets (GNPs) in the EVA–HDPE matrix and the compatibility between the GNPs and the EVA–HDPE matrix. The GNP@PANI nanocomposites and EVA were first prepared as a premix through solution mixing, and then, the premix and HDPE were prepared as highly antistatic composites through melt blending. The dispersion of the GNPs in the EVA–HDPE matrix and the compatibility between the GNPs and the EVA–HDPE matrix were confirmed by field emission scanning electron microscopy and transmission electron microscopy observations. The GNP@PANI–EVA–HDPE composites met the requirements for antistatic materials when the content of the GNP@PANI nanocomposites was 5 wt % with only about 1 wt % GNPs. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45303.     

Compatibility of HDPE/postconsumer HDPE blends using compatibilizing agents

Mechanical properties, molecular weight, X‐ray diffraction, and differential scanning calorimetry (DSC) characterization of blends of virgin high‐density polyethylene (HDPE) with two types of recycled material were investigated. The recycled came from urban plastic waste; one kind was only washed and grounded and the other was extruded and pelletized to remove most of contaminant particles. Starting with the 30/70 virgin/grounded recycled and 50/50 virgin/pelletized recycled blends the recycled content was increased in both blends and compatibilizing agents were used to increase the blend performance. A mixture of phenolic antioxidants and phosphite costabilizers under the name of Recycloblend?, ethylene vinyl acetate (EVA) copolymer, low‐density polyethylene (LDPE), and linear low density polyethylene (LLDPE) were used as compatibilizers. The effect of these additives and the recycled content on the performance of extrusion blow‐molded bottles was determined. The results suggest that blends of virgin/grounded recycled and virgin/pelletized recycled HDPE, in general, were not significantly different among each other and both had a quite similar behavior than the virgin HDPE when compatibilizing agents were used. The addition of compatibilizing agents yielded a material with properties similar to those for the virgin HDPE, helping to reduce the effect of polymers degradation on the rheological and mechanical behavior, with Recycloblend and LLDPE being the most effective for the blends with grounded recycled material, and LLDPE y EVA, for the blends with pelletized recycled. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3696–3706, 2006     

Effect of electron beam irradiation and vinyl acetate content on the physicochemical properties of LDPE/EVA blends

The radiation‐induced crosslinking, compatibility, and surface modification of low density polyethylene/ethylene vinyl acetate blends (LDPE/EVA) were investigated. The structural and physical properties were characterized in terms of gel content, hot set, mechanical properties, contact angle, and surface free energy. The highest crosslink density was obtained at 20 wt % of EVA. Gel content of LDPE/EVA blends was increased with increasing irradiation dose, vinyl acetate (VA), and EVA contents. The hot set results are consistent with the gel content data. Mechanical testing showed that the tensile strength of samples increased with increasing irradiation dose up to 180 kGy, whereas the elongation at break was decreased with increasing irradiation dose. Contact angle measurements showed that the surface hydrophillicity of LDPE blend was increased with increasing irradiation dose and contents of both VA and EVA. The surface free energy was greatly dependent on irradiation dose and content of both VA and EVA. The total surface free energies of different LDPE formulations were in the range 17.25–32.51 mN/m, in which the polar (^pσ) and disperse (^dσ_s) values were within the range 16.52–26.6 and 0.9–5.91 mN/m, respectively. In conclusion, electron beam irradiation and blending LDPE with EVA improved the wettability or adhesion properties of LDPE/EVA blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Development of new thermoplastic elastomers from blends of polyethylene and ethylene–vinyl acetate copolymer by electron‐beam technology

Electron beam‐initiated crosslinking of films prepared from a blend of low‐density polyethylene (LDPE) and ethylene–vinyl acetate (EVA) containing 45% vinyl acetate, with ditrimethylol propane tetraacrylate (DTMPTA), was carried out over a range of radiation doses (20–500 kGy), concentration of DTMPTA (1–5 parts by weight), and blend compositions. The gel fraction of the films increases with increase in the irradiation dose, DTMPTA level, and EVA content of the blends. The mechanical and dynamic mechanical properties of the films are also changed with the above variables. Reprocessibility studies revealed that the blends irradiated at 50 kGy and below are thermoplastic elastomers with a low permanent set. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1877–1889, 2001     

Study on the morphology and properties of metallocene polyethylene and ethylene/vinyl acetate blends

Two commercial polymer materials, metallocene linear low density polyethylene (m‐LLDPE) and ethylene/vinyl acetate copolymer (EVA) have been used to form binary blends of various compositions. The mechanical properties, morphology, rheological behavior, dynamic mechanical properties, and crystallization of m‐LLDPE/EVA blends were investigated. It was found that with the addition of EVA, the fluidity and processability of m‐LLDPE were significantly improved, and the introduction of polar groups in this system showed no significant changes in mechanical properties at lower EVA content. As verified by morphology observation and differential scanning calorimetry analysis, miscible blends were formed within certain weight ratios. Dynamic mechanical property studies showed that flexibility of the blends was enhanced in comparion with pure m‐LLDPE, where the peak value of loss modulus shifted to lower temperature and its intensity was enhanced as EVA content increased, indicating the existence of more amorphous regions in the blends. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 905–910, 2004     

EVA对HDPE光交联反应的影响

采用测定凝胶含量的方法,以二苯甲酮(BP)作为光引发剂、三羟甲基丙烷三丙烯酸酯(TMP-TA)为交联剂,研究了辐照时间、乙烯-醋酸乙酯共聚物(EVA)含量对EVA/HDPE复合材料光交联的影响,并且考察了光交联后EVA/HDPE复合材料的力学性能。研究结果表明,EVA的加入会显著改变体系的凝胶含量;而辐照时间对EVA/HDPE体系交联反应影响很大;体系的力学性能随着EVA含量的增加而变化。     

Rheology, Morphology and Estimation of Interfacial Tension of LDPE/EVA and HDPE/EVA Blends

Summary Rheological characteristics and morphology of low-density polyethylene (LDPE) /ethylene vinyl acetate copolymer (EVA) and high-density polyethylene (HDPE)/EVA blends were compared. Morphological examinations clearly reveal a two-phase morphology in which the LDPE/EVA blends have smaller dispersed domain size than HDPE/EVA Furthermore, LDPE/EVA shows a finely interconnected morphology at 50wt% of EVA while HDPE/EVA exhibits a coarse co-continuous morphology at the same composition. The morphological observations can be attributed to the lower viscosity ratio and lower interfacial tension in the LDPE/EVA system. The Palierne model also successfully fits to the experimental data giving higher values for interfacial tension of HDPE/EVA system as compared to LDPE/EVA.     

Plastification of poly(vinyl chloride) by polymer blending

Blends of poly(vinyl chloride) (PVC) with different copolymers have been studied to obtain a plasticized PVC with improved properties and the absence of plasticizer migration. The copolymers used as plasticizers in the blends were acrylonitrile butadiene rubber, ethylene vinyl acetate (EVA), and ethylene-acrylic copolymer (E-Acry). Blends were studied with regard to their processing, miscibility, and mechanical properties, as a function of blend and copolymer composition. The results obtained were compared with those of equivalent compositions in the PVC/dioctyl phthalate (DOP) system. Better results than PVC/DOP were obtained for PVC/acrylonitrile butadiene rubber blends. The plasticizing effect on PVC of EVA and E-Acry copolymers was similar to that of DOP. It is shown that crosslinking PVC/E-Acry blends or increasing the vinyl acetate content in PVC/EVA blends, are alternatives that can increase the compatibility and mechanical properties of these blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1303–1312, 2000     

Effect of heterophasic or random PP copolymer on the compatibility mechanism between EVA and PP copolymers

Compatibility mechanisms between EVA and PP copolymers (C‐PP) blends have been studied as a function of the type of copolymer, using a heterophasic PP copolymer (PP‐EP) and a random PP copolymer (PP‐r‐EP), with similar ethylene content. The morphology and thermal and mechanical properties of PP/EVA blends with different levels of EVA containing 28% vinyl acetate (VA) were determined. The obtained results indicated compatibility for both systems showing interactions at the amorphous interfaces; however, this interaction was higher for the PP‐r‐EP/EVA, which showed a single glass transition temperature and changes in the PP crystalline fraction (changes in the fusion temperature and in the diffraction patterns). The evolution of the morphology from isolated spherical domains (20% EVA) to elongated shapes (40% EVA) was related to the observed changes in thermal and mechanical properties. The impact strength and deformation properties showed significant improvement with increasing EVA content above 40% where the highest values of elongation for the PP‐r‐EPand of impact strength for the PP‐EP were obtained. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of EVA copolymer on properties of different polyethylenes in silane crosslinking process

Abstract

The effect of molecular structure of polyethylene (PE) [low density PE (LDPE), linear LDPE and high density PE] and silane/peroxide concentration on the grafting level and gel content in silane crosslinking process has been studied. The effect of incorporation of ethylene vinyl acetate (EVA) copolymer on the rate of crosslinking and thermal properties of PEs has been reported. The order of gel content was LDPE>linear LDPE>high density PE. With the incorporation of EVA, the rate of crosslinking increased. The degree of crystallinity did not change with crosslinking significantly. However, the shape of melting and crystallisation peaks changed, and two regions due to gel and sol parts were formed. In EVA/PE blends, two melting points were observed for both crosslinked and uncrosslinked samples. The SEM images showed the droplet matrix morphology with the EVA as the dispersed phase, especially for EVA/LDPE blend. The EVA/PE blends failed in hot set test, while the origin of PEs passed the hot set test successfully.     

Mechanical and thermal properties of blends of low‐density polyethylene and ethylene vinyl acetate crosslinked by both dicumyl peroxide and ionizing radiation for wire and cable applications

Formulations of chemically crosslinked and radiation‐crosslinked low‐density polyethylene (LDPE) containing an intumescent flame retardant such as ammonium polyphosphate were prepared. The influence of blending LDPE with a poly(ethylene vinyl acetate) copolymer (EVA) and the effects of various coadditives, including polyethylene grafted with maleic anhydride (PEgMA), vinyl silane with boric acid, and talc, on the mechanical and thermal properties were investigated. Chemical crosslinking by dicumyl peroxide and crosslinking by ionizing radiation from an electron‐beam accelerator were both used and compared. Improved mechanical properties were observed by the partial replacement of LDPE with EVA. Similar mechanical or thermal properties were observed with coadditives such as PEgMA and vinyl silane with boric acid. The addition of a small amount of talc improved the tensile strength of the formulations. All crosslinked formulations showed good thermal stability on the basis of the retention of mechanical properties after thermal aging for 168 h at 135°C and a hot‐set test. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Study on viscoelastic,crystallization, and mechanical properties of HDPE/EVA/Mg(OH)2 composites

In this article, elastomer‐toughened high density polyethylene/magnesium hydroxide (HDPE/MH) composites with various contents of ethylene vinyl acetate copolymer (EVA) are prepared in a twin‐screw extruder and then injection‐molded. The effect of EVA on the viscoelastic, crystallization, morphology, and tensile properties of the HDPE/EVA/MH composites is studied. The rheological behaviors show that the complex viscosity, storage, and loss modulus at low frequencies are largely unaffected with various EVA contents; however, the corresponding values decrease with increasing EVA content at high frequencies. The scanning electronic microscopy studies on the HDPE/EVA/MH composites show that the MH particles mainly disperse in the EVA phase, and the interfacial adhesion has been also enhanced due to the addition of EVA. The crystallization of HDPE diminishes because of the surface energy difference resulting in encapsulation structure. The tensile properties of the HDPE/EVA/MH composites are strong influenced by the incorporation of EVA. POLYM. COMPOS., 38:1221–1226, 2017. © 2015 Society of Plastics Engineers     

辐射交联LDPE/EVA混合体系泡沫片材性能的研究

辐射交联LDPE/EVA混合体系泡沫片材表观光滑、柔软,手感好,表观密度较小,材料具有优异的力学性能,较高的拉伸强度、断裂伸长率和撕裂强度。进一步研究了产生宏观性能差异的原因是辐射交联LDPE/EVA混合体系泡沫片材制备成型工艺的特殊性,体系的交联度对制品性能影响很大。通过凝胶分析知道交联度与辐照剂量、LDPE树脂的物理性能和EVA树脂在混合体系的含量有关。此外,LDPE树脂的物理性能和EVA在混合体系的含量对材料宏观性能也有影响。