Study on the properties of polyethylene–octene elastomer/wood flour blends

In the present study, the properties of metallocene polyethylene–octene elastomer (POE) and wood flour (WF) blends were examined by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), an Instron mechanical tester, and scanning electron microscopy (SEM). The results showed that the mechanical properties of POE were obviously lowered, due to the poor compatibility between the two phases, when it was blended with WFs. A fine dispersion and homogeneity of WF in the polymer matrix could be obtained when acrylic acid‐grafted POE (POE‐g‐AA) was used to replace POE for manufacture of the blends. This better dispersion is due to the formation of branched and crosslinked macromolecules since the POE‐g‐AA copolymer had carboxyl groups to react with the hydroxyls. This is reflected in the mechanical and thermal properties of the blends. In comparison with a pure POE/WF blend, the increase in tensile strength at break was remarkable for the POE‐g‐AA/WF blend. The POE‐g‐AA/WF blends are more easily processed than are the POE/WF blends, since the former had a lower melt viscosity than that of the latter. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1919–1924, 2003     

Compatibilizing effect of starch‐grafted‐poly(L‐lactide) on the poly(ε‐caprolactone)/starch composites

The poly(ε‐caprolactone) (PCL)/starch blends were prepared with a coextruder by using the starch grafted PLLA copolymer (St‐g‐PLLA) as compatibilizers. The thermal, mechanical, thermo‐mechanical, and morphological characterizations were performed to show the better performance of these blends compared with the virgin PCL/starch blend without the compatibilizer. Interfacial adhesion between PCL matrix and starch dispersion phases dominated by the compatibilizing effects of the St‐g‐PLLA copolymers was significantly improved. Mechanical and other physical properties were correlated with the compatibilizing effect of the St‐g‐PLLA copolymer. With the addition of starch acted as rigid filler, the Young's modulus of the PCL/starch blends with or without compatibilizer all increased, and the strength and elongation were decreased compared with pure PCL. Whereas when St‐g‐PLLA added into the blend, starch and PCL, the properties of the blends were improved markedly. The 50/50 composite of PCL/starch compatibilized by 10% St‐g‐PLLA gave a tensile strength of 16.6 MPa and Young's modulus of 996 MPa, respectively, vs. 8.0 MPa and 597 MPa, respectively, for the simple 50/50 blend of PCL/starch. At the same time, the storage modulus of compatibilized blends improved to 2940 MPa. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of the compatibilizer on the morphology and properties of dynamically cured PP/POE/epoxy blends

Dynamic vulcanization was successfully applied to epoxy resin reinforced polypropylene (PP)/ethylene‐octene copolymer (POE) blends, and the effects of different compatibilizers on the morphology and properties of dynamically cured PP/POE/epoxy blends were studied. The results show that dynamically cured PP/POE/epoxy blends compatibilized with maleic anhydride‐grafted polypropylene (MAH‐g‐PP) have a three‐phase structure consisting of POE and epoxy particles dispersed in the PP continuous phase, and these blends had improved tensile strength and flexural modulus. While using maleic anhydride‐grafted POE (MAH‐g‐POE) as a compatibilizer, the structure of the core‐shell complex phase and the PP continuous phase showed that epoxy particles could be embedded in MAH‐g‐POE in the blends, and gave rise to an increase in impact strength, while retaining a certain strength and modulus. DSC analysis showed that the epoxy particles in the blends compatibilized with MAH‐g‐PP were more efficient nucleating agents for PP than they were in the blends compatibilized with MAH‐g‐POE. WAXD analysis shows that compatibilization do not disturb the crystalline structure of PP in the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Biodegradation of blends of polyethylene‐octene elastomer with starches by fungi

Five fungi including Aspergillus niger, Penicilium pinophilum, Chaetoomium globsum, Gliocladium virens and Aureobasium pullulans were used to investigate the biodegradation of starch‐based elastomers: polyethylene‐octene elastomer (POE)/starch and grafted POE‐g‐MAH/starch copolymer blends. The viability of the composite spore suspensions were measured before estimating the fungal growth on the surface of specimens. The weight loss, morphology and mechanical properties of the blended specimens were measured using scanning electron microscopy and a mechanical properties tester after 28 days of culturing. The spore suspension in the experiment showed good viability. Pure POE and POE‐g‐MAH did not allow significant fungal growth. Pure POE did not lose weight or have a change in tensile strength, but pure POE‐g‐MAH lost about 0.07% of its weight with a slight reduction in tensile strength during culture period. There was heavy growth on the surface of POE/starch and POE‐g‐MAH/starch blends after 28 days of culturing. The weight loss of POE/starch and POE‐g‐MAH/starch blends increased with increasing starch content. POE‐g‐MAH/starch blends tended to lose more weight than POE/starch blends. After biodegradation, the surface of POE/starch and POE‐g‐MAH/starch blends became rough with many holes and cracks, indicating that the films were eroded by the fungi. Tensile strength of POE/starch and POE‐g‐MAH/starch blends decreased after culturing because of microbial attack. On the contrary, elongation at break of POE‐g‐MAH/starch blends increased after biodegradation. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci 114:3574–3584, 2009     

Use of poly(ethylene‐co‐vinyl alcohol) as compatibilizer in LDPE/thermoplastic tapioca starch blends

Poly(ethylene‐co‐vinyl alcohol) (EVOH) was used as a compatibilizer to make blends of low‐density polyethylene (LDPE) and plasticized starch (TS). The tensile properties and impact strength were measured and compared with those of neat LDPE. The morphology of the blend specimens, both fractured and unfractured, was observed by scanning electron microscopy. Comparison of the properties showed that the impact strength of the blend improves significantly by the addition of a compatibilizer even with a high TS loading of 40 and 50% (by weight). A high elongation at break almost matching that of neat polyethylene was also obtained. The blend morphology of the etched specimens revealed fine dispersion of the starch in the polyethylene matrix, while the fracture surface morphology clearly indicate that the failure of compatibilized blends occurs mainly by the ductile mode. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3126–3134, 2002     

Effect of interfacial interaction on the crystallization and mechanical properties of PP/nano‐CaCO3 composites modified by compatibilizers

To investigate the effect of interfacial interaction on the crystallization and mechanical properties of polypropylene (PP)/nano‐CaCO₃ composites, three kinds of compatibilizers [PP grafted with maleic anhydride (PP‐g‐MA), ethylene–octene copolymer grafted with MA (POE‐g‐MA), and ethylene–vinyl acetate copolymer grafted with MA (EVA‐g‐MA)] with the same polar groups (MA) but different backbones were used as compatibilizers to obtain various interfacial interactions among nano‐CaCO₃, compatibilizer, and PP. The results indicated that compatibilizers encapsulated nano‐CaCO₃ particles, forming a core–shell structure, and two interfaces were obtained in the compatibilized composites: interface between PP and compatibilizer and interface between compatibilizer and nano‐CaCO₃ particles. The crystallization and mechanical properties of PP/nano‐CaCO₃ composites were dependent on the interfacial interactions of these two interfaces, especially the interfacial interaction between PP and compatibilizer. The good compatibility between PP chain in PP‐g‐MA and PP matrix improved the dispersion of nano‐CaCO₃ particles, favored the nucleation effect of nano‐CaCO₃, increased the tensile strength and modulus, but reduced the ductility and impact strength of composites. The partial compatibility between POE in POE‐g‐MA and PP matrix had little effect on crystallization and mechanical properties of PP/nano‐CaCO₃ composites. The poor compatibility between EVA in EVA‐g‐MA and PP matrix retarded the nucleation effect of nano‐CaCO₃, and reduced the tensile strength, modulus, and impact strength. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Mechanical,thermal, and morphological characteristics of compatibilized and dynamically vulcanized polyoxymethylene/ethylene propylene diene terpolymer blends

Dynamically vulcanized blends of polyoxymethylene (POM) and ethylene propylene diene terpolymer (EPDM) with and without compatibilizer were prepared by melt mixing in a twin screw extruder. Maleic anhydride (MAH) grafted EPDM (EPDM‐g‐MAH) has been used as a compatibilizer. Dicumyl peroxide was used for vulcanizing the elastomer phase in the blends. Mechanical, dynamical mechanical, thermal, and morphological properties of the blend systems have been investigated as a function of blend composition and compatibilizer content. The impact strength of both dynamically vulcanized blends and compatibilized/dynamically vulcanized blends increases with increase in elastomer content with decrease in tensile strength. Dynamic mechanical analysis shows decrease in tanδ values as the elastomer and compatibilizer content increased. Thermograms obtained from differential scanning calorimetric studies reveal that compatibilized blends have lower T_m values compared to dynamically vulcanized blends, which confirms strong interaction between the plastic and elastomer phase. Scanning electron microscopic observations on impact fractured surface indicate reduction in particle size of elastomer phase and its high level of dispersion in the POM matrix. In the case of compatibilized blends high degree of interaction between the component polymers has been observed. POLYM. ENG. SCI., 47:934–942, 2007. © 2007 Society of Plastics Engineers     

Synthesis and characterization of polyethylene‐octene elastomer/clay/biodegradable starch nanocomposites

The aim of this work is the production of new nanocomposites from metallocene polyethylene‐octene elastomer (POE), montmorillonite and biodegradable starch by means of a melt blending method. Characterizations of clay, modified clay, POE, POE‐g‐AA, and the hybrids produced from polymer, clay, and/or starch were performed by X‐ray diffraction (XRD) spectroscopy, Fourier transform infrared (FTIR) spectrophotometer, differential scanning calorimetry (DSC), thermogravimetry analyzer (TGA), scanning electron microscope (SEM), and Instron mechanical tester. As to the results, organophilic clay can be well dispersed into acrylic acid grafted polyethylene‐octene elastomer (POE‐g‐AA) in nanoscale sizes since cetyl pyridium chloride is partially compatible with POE‐g‐AA and allows POE‐g‐AA chains to intercalate into clay layers. Based on consideration of thermal and mechanical properties, it is also found that 12 wt % of clay content is optimal for preparation of POE‐g‐AA/clay nanocomposites. The new partly biodegradable POE‐g‐AA/clay/starch hybrid could obviously improve the elongation and the tensile strength at break of the POE‐g‐AA/starch hybrid since the former can give the smaller starch phase size and nanoscale dispersion of silicate layers in the polymer matrix. The nanocomposites produced from our laboratory can provide a stable tensile strength at break when the starch content is up to 40 wt %. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 397–404, 2005     

Characterizing composite of multiwalled carbon nanotubes and POE‐g‐AA prepared via melting method

Multiwalled carbon nanotubes (MWNTs) with acyl chloride functional groups and a metallocene polyethylene–octene elastomer (POE) or an acrylic acid‐grafted metallocene polyethylene–octene elastomer (POE‐g‐AA) were used to prepare hybrids (POE/MWNTs or POE‐g‐AA/MWNTs) using a melting method, with a view to identify a hybrid with improved thermal properties. Hybrids were characterized using Fourier transform infrared spectroscopy, ¹³C solid‐state nuclear magnetic resonance, X‐ray diffraction, thermogravimetry analysis, and scanning electron microscopy. MWNTs were purified using acid treatment, and results showed that ? COOH of MWNTs increased with acid treatment time and leveled off after 24‐h treatment. Much better dispersion and homogeneity of MWNTs was obtained with POE‐g‐AA in place of POE as the matrix. As a result, tensile strength at break of POE‐g‐AA/MWNTs was significantly improved even at 5 wt % MWNT content. Moreover, temperature of thermal decomposition for POE‐g‐AA/MWNTs was about 40–50°C higher than that for POE‐g‐AA, indicating higher thermal stability. This was because the carboxylic acid groups in POE‐g‐AA and the acyl chloride functional sites in MWNTs allow the formation of stronger chemical bonds. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1328–1337, 2007     

Polypropylene/polypropylene‐grafted acrylic acid copolymer/ethylene–Acrylic acid copolymer ternary blends for hydrophilic polypropylene

Ternary blends of polypropylene (PP), a polypropylene‐grafted acrylic acid copolymer (PP‐g‐AA), and an ethylene–acrylic acid copolymer (EAA) were prepared by melt blending. The surfaces of films with different contents of these three components were characterized with contact‐angle measurements. Scanning electron microscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, and thermogravimetric analysis were used to characterize the microstructure, melting and crystalline behavior, and thermal stability of the blends. The contact angles of the PP/PP‐g‐AA blends decreased monotonically with increasing PP‐g‐AA content. With the incorporation of EAA, the contact angles of the PP/PP‐g‐AA/EAA ternary blends decreased with increasing EAA content. When the concentration of EAA was higher than 15 wt %, the contact angles of the ternary blends began to increase. Scanning electron microscopy observations confirmed that PP‐g‐AA acted as a compatibilizer and improved the compatibility between PP and EAA in the ternary blends. Differential scanning calorimetry analysis suggested that acrylic acid moieties could act as nucleating agents for PP in the polymer blends. Thermogravimetric analysis and differential thermogravimetry confirmed the optimal blend ratio for the PP/PP‐g‐AA/EAA ternary blends was 70/15/15. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 436–442, 2006     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Influences of compatibilizers on rheology and mechanical properties of propylene random copolymer/styrene‐ethylene‐butylene‐styrene block copolymer/organic‐montmorillonite nanocomposites

Propylene random copolymer (PPR)/styrene‐ethylene‐butylene‐styrene block copolymer (SEBS)/compatibilizer/organic‐montmorillonite (OMMT) quaternary nanocomposites and PPR/compatibilizer/OMMT ternary nanocomposites were prepared via two‐stage melt blending and influences of compatibilizers, maleic anhydride (MA) grafted styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), poly(octene‐co‐ethylene) (POE‐g‐MA), or propylene block copolymers (PPB‐g‐MA), on rheology and mechanical properties of the nanocomposites were investigated. The results of X‐ray diffraction measurement and transmission electron microscopy observation showed that OMMT layers were mainly intercalated in the nanocomposites except for the mainly exfoliated structure in the quaternary nanocomposites using POE‐g‐MA as compatibilizer. The nanocomposites exhibited pseudo‐solid like viscoelasticity in low frequencies and shear‐thinning in high shear rates. As far as OMMT dispersion was concerned, POE‐g‐MA was superior to SEBS‐g‐MA and PPB‐g‐MA, which gives rise to the highest viscosities in both the ternary and quaternary nanocomposites. The quaternary nanocomposites containing POE‐g‐MA were endowed with balanced toughness and rigidity. It was suggested that a suitable combination of compatibilizer and SEBS was an essentially important factor for adjusting the OMMT dispersion and distribution, the rheological and mechanical performances of the nanocomposites. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Phase structure and viscoelastic properties of compatibilized blends of PET and HDPE recyclates

Immiscible blends of recycled poly(ethylene terephthalate) (R‐PET), containing some amount of polymeric impurities, and high‐density polyethylene (R‐PE), containing admixture of other polyolefins, in weight compositions of 75 : 25 and 25 : 75 were compatibilized with selected compatibilizers: maleated styrene–ethylene/butylene–styrene block copolymer (SEBS‐g‐MA) and ethylene–glycidyl methacrylate copolymer (EGMA). The efficiency of compatibilization was investigated as a function of the compatibilizer content. The rheological properties, phase structure, thermal, and viscoelastic behavior for compatibilized and binary blends were studied. The results are discussed in terms of phase morphology and interfacial adhesion among components. It was shown that the addition of the compatibilizer to R‐PET‐rich blends and R‐PE‐rich blends increases the melt viscosity of these systems above the level characteristic for the respective binary blends. The dispersion of the minor phase improved with increasing compatibilizer content, and the largest effects were observed for blends compatibilized with EGMA. Calorimetric studies indicated that the presence of a compatibilizer had a slight affect on the crystallization behavior of the blends. The dynamic mechanical analysis provided evidence that the occurrence of interactions of the compatibilizer with blend components occurs through temperature shift and intensity change of a β‐relaxation process of the PET component. An analysis of the loss spectra behavior suggests that the optimal concentration of the compatibilizers in the considered blends is close to 5 wt %. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1423–1436, 2001     

LDPE/starch blends compatibilized with PE-g-MA copolymers

In the present study, low-density polyethylene (LDPE) and plasticized starch (PLST) blends, containing different percentages of PLST, were prepared. In these blends, two different polyethylene/maleic anhydride graft (PE-g-MA) copolymers containing 0.4 and 0.8 mol % anhydride groups, respectively, were added as compatibilizers at 10 wt % PLST. The compatibilization reaction was followed by FTIR spectroscopy. The morphology of the blends was studied using scanning electron microscopy (SEM). It was found that as the amount of anhydride groups in the copolymers increases a finer dispersion of PLST in the LDPE matrix is achieved. This is reflected in the mechanical properties of the blends and especially in the tensile strength. The blends compatibilized with the PE-g-MA copolymer containing 0.8 mol % anhydride groups have a higher tensile strength, which in all blends, even in those containing 20 and 30 wt % PLST, is similar to that of pure LDPE. The biodegradation of the blends followed the exposure to activated sludge. It was found that the compatibilized blends have only a slightly lower biodegradation rate compared to the uncompatibilized blends. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 70: 1503–1521, 1998     

Effect of epoxy functionalized compatibilizer on the mechanical properties of low‐density polyethylene/plasticized tapioca starch blends

A series of low‐density polyethylene (LDPE) blends with varying proportions of plasticized tapioca starch have been used for the study of their mechanical properties. A functionalized epoxy resin, namely, poly(ethylene‐co‐glycidyl methacrylate) has been used as the compatibilizer. The impact and tensile properties have been measured by standard ASTM methods. The mechanical properties are seen to improve significantly with the addition of the epoxy compatibilizer, approaching values close to those of virgin LDPE. The scanning electron micrographs of the compatibilized blends show ductile failure which evidently contribute to improved mechanical properties. © 2001 Society of Chemical Industry     

Polyoxymethylene/ethylene butylacrylate copolymer/ethylene‐methyl acrylate‐glycidyl methacrylate ternary blends

Blends of compatibilized polyoxymethylene (POM)/ethylene butylacrylate copolymer (EBA)/ethylene‐methyl acrylate‐glycidyl methacrylate copolymer (EMA‐GMA) and uncompatibilized POM/EBA were investigated. The notched impact strength of the compatibilized blends was higher than that of their uncompatibilized counterparts. The toughness of the POM blends was improved obviously with relatively low loading of EBA. Fourier transform infrared spectroscopy (FTIR) spectra of EMA‐GMA, pure POM, and POM/EBA/EMA‐GMA blends indicated that epoxy groups of EMA‐GMA reacted with terminal hydroxyl groups of POM molecular chains. The glass‐transition temperature (T_g) values of the POM matrix and the EBA phase were observed shifted to each other in the presence of EMA‐GMA compatibilizer indicating that the compatibilized blends had better compatibility than their uncompatibilized counterparts. With the addition of EBA to POM, both the compatibilized and uncompatibilized blends showed higher onset degradation temperature (T_d) than that of pure POM and the T_d values of the compatibilized blends were higher than those of their uncompatibilized counterparts. The scanning electron microscopy showed better EBA particles distribution state in the compatibilized system than in the uncompatibilized one. The compatibilized blend with an obvious rougher impact fracture surface indicated the ductile fracture mode. POLYM. ENG. SCI., 58:1127–1134, 2018. © 2017 Society of Plastics Engineers     

增容剂EAA对PA6／POE共混体系的相态及性能的影响

采用乙烯－丙烯酸共聚物（EAA）作为尼龙6／乙烯－1－辛烯共聚物弹性体（POE）共混体系的增容剂,详细研究了增容剂用量与共混体系的相态、力学性能和流变性能的关系。结果表明相容剂的加入使共混体系的分散性大大改善,分散相POE粒子明显细化,粒子较均匀地分散在PA6连续相中;相容剂的加入使体系韧性明显提高,拉伸强度和弯曲弹性模量下降,加工性能也得到改善,而且当每100份PA6／POE用量为85／15、EAA用量在4月份左右时,其增容作用达到饱和,综合性能达到最优。     

Toughening effects of poly(butylene terephthalate) with blocked isocyanate‐functionalized poly(ethylene octene)

BACKGROUND: Blocked isocyanate‐functionalized polyolefins have great potential for use in semicrystalline polymer blends to obtain toughened polymers. In this study, poly(butylene terephthalate) (PBT) was blended with allyl N‐[2‐methyl‐4‐(2‐oxohexahydroazepine‐1‐carboxamido)phenyl] carbamate‐functionalized poly(ethylene octene) (POE‐g‐AMPC). RESULTS: New peaks at 2272 and 1720 cm^?1, corresponding to the stretching vibrations of NCO and the carbonyl of NH? CO? N, respectively, in AMPC, appeared in the infrared spectrum of POE‐g‐AMPC. Both rheological and X‐ray photoelectron spectroscopy results indicated a new copolymer was formed in the reactive blends. Compared to uncompatibilized PBT/POE blends, smaller dispersed particle sizes with narrower distribution were found in the compatibilized PBT/POE‐g‐AMPC blends. There was a marked increase in impact strength by about 10‐fold over that of PBT/POE blends with the same rubber content and almost 30‐fold higher than that of pure PBT when the POE‐g‐AMPC content was 25 wt%. CONCLUSION: The blocked isocyanate‐functionalized POE is an effective toughener for semicrystalline polymers. Super‐toughened PBT blends can be obtained when the POE‐g‐AMPC content is equal to or more than 15 wt%. Copyright © 2009 Society of Chemical Industry     

Graft reaction of acrylic acid onto metallocene‐based polyethylene‐octene elastomer

In this study, grafting of acrylic acid (AA) onto metallocene‐based polyethylene‐octene elastomer (POE) was investigated by using benzoyl peroxide as an initiator. Grafted product was characterized by using Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, X‐ray diffraction spectroscopy, and differential scanning calorimetry (DSC). Both the grafting percentage and the gel yield, at equilibrium, were higher for POE containing lower degree of comonomer content. In all cases, the crosslinking reaction was accompanied by the predominant graft reaction due to the competition of POE macroradical and excited AA. From the result of DSC and X‐ray characterizations, it was found that the change of crystallinity is slight when the gel is removed from POE‐g‐AA copolymers. It was also proven that the effect of gel formation on the properties of the copolymer could be neglected because of the low gel yield. So, the graft method proposed in this article can produce low gel yield copolymer. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2905–2912, 2002     

Morphological,thermal, rheological,and mechanical properties of PP/EVOH blends compatibilized with PP‐g‐IA

We prepared some blends of polypropylene (PP) and ethylene vinyl alcohol (EVOH) with and without a compatibilizer. As a new compatibilizer, we synthesized polypropylene grafted with itaconic acid (PP‐g‐IA) using Brabender mixing system. We investigated the morphological, thermal, rheological, and mechanical properties of a compatibilized blends (PP/EVOH/PP‐g‐IA) and not compatibilized blends (PP/EVOH). Our experiments showed that carboxylic acid groups in PP‐g‐IA and hydroxyl group in EVOH formed strong in situ hydrogen bond in the compatibilized blends, resulting in better morphological and mechanical properties of the compatibilized blends than those of not compatibilized blends. POLYM. ENG. SCI., 56:1240–1247, 2016. © 2016 Society of Plastics Engineers