Pervaporation separation of water‐isopropanol mixtures using polymeric membranes: Modeling and simulation aspects

Pervaporation technique was used to separate water + isopropanol azeotropic mixtures at 30°C using pure sodium alginate, pure poly(vinyl alcohol), and blend membranes of sodium alginate containing 10 and 20 mass % of poly(vinyl alcohol). The membrane performance was studied by calculating flux, selectivity, pervaporation separation index, and enrichment factor. Pure sodium alginate membrane gave the highest pervaporation separation index for all compositions of water. Pervaporation experiments were carried out for 10 mass % containing water + isopropanol mixture at 30, 40, and 50°C. The Arrhenius activation parameters were computed. The PV results have been analyzed by considering complete mixing and plug flow models. Design parameters, like membrane area, permeate concentrations, flux, stage cut, separation selectivity, etc., have been calculated for different feed compositions of water in the mixture. Results are explained in terms of sorption‐diffusion principles. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1143–1153, 2005     

Pervaporation separation of water‐isopropyl alcohol mixtures with blend membranes of sodium alginate and poly(acrylamide)‐grafted guar gum

The blend membranes of sodium alginate (Na‐Alg) and poly(acrylamide)‐grafted guar gum (PAAm‐g‐GG) in the ratios of 3:1 and 1:1 were prepared and studied for the pervaporation separation of water–isopropyl alcohol mixtures over the entire range of mixture composition at 30°C. Membranes prepared from neat Na‐Alg (M‐1) and the 1:1 blend of Na‐Alg and PAAm‐g‐GG (M‐3) showed the highest separation selectivity for 10 mass % water in the feed mixture, whereas membranes prepared with the 3:1 blend ratio of Na‐Alg to PAAm‐g‐GG showed the highest separation selectivity of 20 mass % water in the feed. Selectivity decreased with increasing amount of water in the feed for all the membranes, but these values show an increase with increasing amount of grafted copolymer in the blend mixture. Flux increased with increasing amount of water in the mixture, but the flux values did not change markedly with the PAAm‐g‐GG content in the blend membrane at the lower mass % water. At higher mass % of water, the flux values of the blends increase systematically with increasing amount of PAAm‐g‐GG in the blend polymer. For the 10 mass %‐containing binary mixtures, the pervaporation separation experiments were performed at 30, 40, and 50°C, and the resulting data were used to calculate the Arrhenius activation parameters. These data indicated activated pore‐type diffusion of the permeants in the membranes. Dynamic sorption studies were also performed on up to 40 mass % water–isopropyl alcohol mixtures at 30°C. These results, when analyzed by the empirical equation, indicated Fickian transport in all the cases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2014–2024, 2002     

Synthesis of graft copolymeric membranes of poly(vinyl alcohol) and polyacrylamide for the pervaporation separation of water/acetic acid mixtures

Graft copolymers of poly(vinyl alcohol) (PVA) with polyacrylamide were prepared and membranes were fabricated at 48 and 93% grafting of acrylamide onto PVA. These membranes were used in the pervaporation separation of water/acetic acid mixtures at 25, 35, and 45°C. The permeation flux, separation selectivity, diffusion coefficient, and permeate concentration were determined. The highest separation selectivity of 23 for neat PVA at 25°C and the lowest value of 2.2 for 93% acrylamide‐grafted PVA membranes were observed. A permeation flux of 1.94 kg m^?2 h^?1 was found for the 93% grafted membrane at 90 mass % of water in the feed mixture. The diffusion coefficients in a water/acetic acid mixture had an effect on the membrane permselectivity. The Arrhenius equation was used to calculate the activation parameters for permeation as well as for the diffusion of water and of acetic acid. The activation energy values for the permeation flux varied from 97 to 28 kJ/mol. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 244–258, 2002     

Computer simulation and comparative study on the pervaporation separation characteristics of sodium alginate and its blend membranes with poly(vinyl alcohol) to separate aqueous mixtures of 1,4‐dioxane or tetrahydrofuran

A comparative study on the pervaporation separation has been attempted for water + 1,4‐dioxane and water + tetrahydrofuran mixtures using sodium alginate and blend membranes of sodium alginate with 5, 10, and 20 mass % of poly(vinyl alcohol). Pure sodium alginate membrane has a selectivity of 111 to water at 0.35‐mol fraction of water in the feed mixture containing 1,4‐dioxane while for water + tetrahydrofuran mixture, the membrane selectivity to water was 291 at 0.31‐mol fraction of water in the feed mixture. Pervaporation results have been discussed using the solution–diffusion principles. Arrhenius activation parameters for diffusion and permeation have been computed from the temperature‐dependent pervaporation results. Furthermore, experimental results have been analyzed using the complete mixing and plug flow models to compute membrane area as well as design parameters that are useful in scale‐up operations. The plug flow model is more appropriate than the complete mixing model to analyze the pervaporation results. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1827–1840, 2004     

Synthesis and characterization of polyacrylamide‐grafted sodium alginate copolymeric membranes and their use in pervaporation separation of water and tetrahydrofuran mixtures

Polyacrylamide‐grafted sodium alginate (PAAm‐g‐Na‐Alg) copolymeric membranes have been prepared, characterized, and used in the pervaporation separation of 10–80 mass % water‐containing tetrahydrofuran mixtures. Totally three membranes were prepared: (1) neat Na‐Alg with 10 mass % of polyethylene glycol (PEG) and 5 mass % of polyvinyl alcohol (PVA), (2) 46 % grafted PAAm‐g‐Na‐Alg membrane containing 10 mass % of PEG and 5 mass % of PVA, and (3) 93 % grafted PAAm‐g‐Na‐Alg membrane containing 10 mass % of PEG and 5 mass % of PVA. Using the transport data, important parameters like permeation flux, selectivity, pervaporation separation index, swelling index, and diffusion coefficient have been calculated at 30°C. Diffusion coefficients were also calculated from sorption gravimetric data of water–tetrahydrofuran mixtures using Fick's equation. Arrhenius activation parameters for the transport processes were calculated for 10 mass % of water in the feed mixture using flux and diffusion data obtained at 30, 35, and 40°C. The separation selectivity of the membranes ranged between 216 and 591. The highest permeation flux of 0.677 kg/m² h was observed for 93% grafted membrane at 80 mass % of water in the feed mixture. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 272–281, 2002     

Sorption,diffusion, and pervaporation separation of water–acetic acid mixtures through the blend membranes of sodium alginate and guar gum‐grafted‐polyacrylamide

Nonporous homogeneous dense membranes were prepared from the blends of sodium alginate (Na–Alg) with guar gum‐grafted polyacrylamide (GG‐g‐PAAm) in the ratios of 3 : 1 and 1 : 1 and these were tested for the pervaporation separation of water–acetic acid mixtures at 30°C. Blend compatibility was studied in solution by measuring the viscosity and the speed of sound. Membranes were crosslinked by glutaraldehyde. The GG‐g‐PAAm polymer and the crosslinked blend membranes were characterized by Fourier transform infrared spectra. High separation selectivity was exhibited by the pure Na–Alg membrane for water–acetic acid (HAc) mixtures containing 20 mass % of water. The permeation flux increased with increasing mass percent of water in the feed as well as with an increase in the amount of GG‐g‐PAAm in the blend, but separation selectivity decreased. Sorption selectivity was higher for the Na–Alg membrane than for the blend membranes, but it decreased with increasing mass percent of GG‐g‐PAAm in the blends. Diffusion selectivity values vary systematically with the blend composition, but not with the amount of water in the feed. Diffusion coefficients of the water–HAc mixtures were calculated from Fick's equation using sorption data and compared with those calculated from flux values obtained in pervaporation experiments. The Arrhenius activation parameters were calculated for the 20 mass % of water in the feed using flux and diffusion data obtained at 30, 40, and 50°C. The diffusion and pervaporation results are explained in terms of solution–diffusion concepts. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 259–272, 2002     

Synthesis and characterization of polyacrylamidegrafted sodium alginate membranes for pervaporation separation of water + isopropanol mixtures

Polyacrylamide‐grafted‐sodium alginate copolymers were prepared by persulfate‐induced radical polymerization by using polymer‐to‐monomer ratios of 2 : 1 and 1 : 1. Polymers were characterized by Fourier transform infrared spectroscopy, differential thermal analysis, and viscosity. Membranes were prepared from the polymers, crosslinked with glutaraldehyde, and used in the pervaporation separation of water + isopropanol mixtures at 30°C. Equilibrium swelling experiments were performed for mixtures containing 10 to 80 mass % of water in the feed. Both the grafted copolymer membranes were ruptured while separating 10 mass % of water in the feed mixture. However, beyond 20 mass % of water in the feed mixture, flux increased with increasing grafting ratio, while selectivity decreased. Pervaporation separation experiments were carried out at 30, 40, and 50°C for 20 mass % of water in the feed mixture. By increasing the temperature, flux increased, whereas selectivity decreased. Arrhenius activation parameters for pervaporation and diffusion decreased with increasing grafting ratio of the membranes. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2030–2037, 2004     

Synthesis and characterization of hybrid membranes using poly(vinyl alcohol) and tetraethylorthosilicate for the pervaporation separation of water–isopropanol mixtures

Hybrid membranes were prepared using poly(vinyl alcohol) (PVA) and tetraethylorthosilicate (TEOS) via hydrolysis and cocondensation reaction for the pervaporation separation of water‐isopropanol mixtures. The resulting membranes were characterized by Fourier transform infrared spectroscopy, wide‐angle X‐ray diffraction, and differential scanning calorimetry. The glass transition temperature of these membranes varied from 100 to 120°C with increasing TEOS content. Effects of crosslinking density and feed compositions on the pervaporation performances of the membranes were studied. The membrane containing 1.5:1 mass ratio of TEOS to PVA gave the highest separation selectivity of 900 at 30°C for 10 mass % of water in the feed mixture. It was found that the separation selectivity and permeation flux data are strongly dependent on the water composition of the feed and operating temperature. However, the membrane with the highest crosslinking density showed unusual pervaporation properties. The overall activation energy values were calculated using the Arrhenius‐type equation. The activation energy values for the permeation and diffusion varied from 49.18 to 64.96 and 55.13 to 67.31 kJ/mol, respectively. Pervaporation data have also been explained on the basis of thermodynamic quantities. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 1304–1315, 2004     

Pervaporation separation of water/dimethylformamide mixtures using poly(vinyl alcohol)‐g‐polyacrylamide copolymeric membranes

Grafted copolymeric membranes of poly(vinyl alcohol) with acrylamide (PVA‐g‐AAm) were developed and used in the pervaporation separation of water–dimethylformamide mixtures by varying the amount of water in the feed from 0 to 100%. From these data, the permeation flux, pervaporation separation index, diffusion coefficient, swelling index, and separation selectivity were calculated at 25, 35, and 45°C. The Arrhenius activation parameters for permeation flux ranged between 22 and 63 kJ/mol, while the activation energy for diffusion ranged between 23 and 67 kJ/mol. Separation selectivity was between 15 and 22. The highest permeation flux of 0.459 kg m^?2 h^?1 was obtained for the 93% grafted membrane at 90% of water in the feed mixture. The results are discussed using the principles of the solution–diffusion model. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 273–282, 2002     

Characterization of sodium alginate and poly(vinyl alcohol) blend membranes in pervaporation separation

By blending a rigid polymer, sodium alginate (SA), and a flexible polymer, poly(vinyl alcohol) (PVA), SA/PVA blend membranes were prepared for the pervaporation separation of ethanol–water mixtures. The rigid SA membrane showed a serious decline in flux and a increase in separation factor due to the relaxation of polymeric chains, whereas the flexible PVA membrane kept consistent membrane performance during pervaporation. Compared with the nascent SA membrane, all of the blend membranes prepared could have an enhanced membrane mobility by which the relaxation during pervaporation operation could be reduced. From the pervaporation separation of the ethanol–water mixtures along with the temperature range of 50–80°C, the effects of operating temperature and PVA content in membrane were investigated on membrane performance, as well as the extent of the relaxation. The morphology of the blend membrane was observed with PVA content by a scanning electron microscopy. The relaxational phenomena during pervaporation were also elucidated through an analysis on experimental data of membrane performance measured by repeating the operation in the given temperature range. SA/PVA blend membrane with 10 wt % of PVA content was crosslinked with glutaraldehyde to enhance membrane stability in water, and the result of pervaporation separation of an ethanol–water mixture through the membrane was discussed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67:949–959, 1998     

Pervaporation performance and Transport phenomenon of PVA blend membranes for the separation of THF/water azeotropic mixtures

Summary Dense polymer membranes were made by mixing aqueous solutions of hydrophilic polymers poly(vinyl alcohol) (PVA) and polyethyleneimine (PEI) in different ratios for investigating the separation of Tetrahydrofuran (THF)/water azeotropic mixtures by pervaporation (PV). In order to gain a more detailed picture of the molecular transport phenomenon, we have performed sorption gravimetric experiments at 30 °C to compute diffusion, swelling, sorption and permeability coefficients of PVA/PEI membranes in the presence of THF and water. The membranes were found to have good potential for breaking the azeotrope of THF at 6% concentration of water. An increase in PVA content in the blend caused a reduction in the flux and an increase in selectivity. Among the blends tested in the study, the 5:1 PVA/PEI blend membrane showed the highest separation factor of 181.5, exhibited a flux of 1.28 kg/m²h for THF respectively at azeotropic feed composition.     

Pervaporation separation of water–isopropanol mixture using carboxymethylated poly(vinyl alcohol) composite membranes

The pervaporation separation of water–isopropanol mixtures was carried out using carboxymethylated poly(vinyl alcohol) (CMPVA) composite membranes. Carboxymethylated PVA (CMPVA) was synthesized by reacting PVA with various concentrations of monochloroacetic acid. Substitution efficiency of the CMPVA ranged from 12–32%. The cross‐sectional structure of the composite membrane for pervaporation was confirmed by scanning electron microscopy (SEM) exhibiting a 20‐μm active skin layer. Glass transition temperature of the CMPVA was in the range of 74–84°C, and decreased with increasing substitution efficiency. Degree of swelling and permeation flux for water–isopropanol in pervaporation increased with the substitution degree of carboxymethylation. CMPVA composite membrane, having 16% substitution efficiency, showed the following pervaporation performance; permeation flux of 831 g/m² h and separation factor of 362 measured at 80°C and 85 wt % feed isopropanol concentration. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 241–249, 1999     

Sorption/diffusion of aqueous mixtures of 1,4‐dioxane/tetrahydrofuran through blend membranes of poly(vinyl alcohol) and sodium alginate: Their compatibility and pervaporation separation studies

Blend membranes of poly(vinyl alcohol) (PVA) and sodium alginate (NaAlg) were prepared by solution casting and crosslinked with glutaraldehyde (GA). Polymer blend compatibility was studied in water by measuring solution viscosity at 30°C. From the viscosity data, interaction parameters were determined to find the blend compatibility. Thickness of the membranes ranged between 35 and 40 μm. Circular disc‐shaped samples were cut from the thin membranes to perform gravimetric sorption experiments in water + 1,4‐dioxane and water + tetrahydrofuran mixtures at 30°C. Diffusion coefficients were calculated using Fick's equation. Concentration profiles of liquids were computed by solving Fick's equation under suitable boundary conditions. Diffusion coefficients show a dependence on the composition of the blends as well as composition of binary mixtures. A correlation was attempted between concentration profiles and diffusion coefficients of the transporting liquids. Degree of swelling and sorption coefficients were calculated from the gravimetric sorption data. Sorption kinetics was studied using an empirical equation to understand the nature of sorption–diffusion anomalies. Membrane selectivity for water + 1,4‐dioxane and water + tetrahydrofuran mixtures were calculated from the pervaporation experiments. A correlation between sorption and membrane selectivity was attempted. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 178–188, 2005     

Mixed matrix membranes of H‐ZSM5‐loaded poly(vinyl alcohol) used in pervaporation dehydration of alcohols: Influence of silica/alumina ratio

Mixed matrix membranes of poly(vinyl alcohol) loaded with zeolite particles having different silica alumina ratio were prepared and used in the pervaporation dehydration of ethanol and isopropanol (IPA) from their aqueous mixtures. The membranes were characterized by physicochemical techniques that revealed higher interaction between polymer and zeolite particles having higher alumina than those with lower alumina in the zeolite framework. Both, membrane selectivity to water and flux were increased as the alumina content in the zeolite increases. Separation factors of zeolite with lower alumina incorporated membranes were, respectively, 236 and 334 for the feed mixture compositions of 4 wt% water in ethanol and 10 wt% water in IPA at 30°C. On the other hand, membranes containing zeolites with higher alumina content showed slightly higher separation factors of 349 and 568, respectively, for the same feed mixtures at 30°C. Such an incremental improvement in membrane performance with increase in alumina content in the zeolite framework is attributed to favorable interaction between zeolite particles and the polymer matrix. POLYM. ENG. SCI., 54:1774–1782, 2014. © 2013 Society of Plastics Engineers     

Blend membranes of chitosan and poly(vinyl alcohol) in pervaporation dehydration of isopropanol and tetrahydrofuran

Blend membranes of a natural polymer, chitosan, with a synthetic polymer, poly(vinyl alcohol) (PVA), were prepared by solution casting and crosslinked with a urea formaldehyde/sulfuric acid (UFS) mixture. Chitosan was used as the base component in the blend system, whereas PVA concentration was varied from 20 to 60 wt %. Blend compatibility was studied by differential scanning calorimetry, and Fourier transform infrared spectroscopy was used to study membrane crosslinking. Membranes were tested for pervaporation dehydration of isopropanol and tetrahydrofuran (THF) at 30°C in close proximity to their azeotropic compositions. Membrane performance was assessed by calculating flux and selectivity. Swelling experiments performed in water + organic mixtures at 30°C were used to explain the pervaporation results. The blend membrane containing 20 wt % PVA when tested for 5 and 10 wt % water–containing THF and isopropanol feeds exhibited selectivity of 4203 and 17,991, respectively. Flux increased with increasing concentration of water in the feed. Selectivity was highest for the 20 wt % PVA‐containing blend membrane. The results of this study are unique in the sense that the crosslinking agent used—the UFS mixture—was novel. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 1918–1926, 2007     

Polyacrylonitrile‐g‐poly(vinyl alcohol) membranes for the pervaporation separation of dimethyl formamide and water mixtures

Poly(vinyl alcohol) as well as its grafted copolymer membranes with polyacrylonitrile (PAN‐g‐PVA) were prepared and used to separate water and dimethyl formamide mixtures by the pervaporation technique. The three following membranes were prepared: (1) pure PVA; (2) 46% grafted PAN‐g‐PVA; and (3) 93% grafted PAN‐g‐PVA. Pervaporation separation experiments were carried out at 25°C for the feed mixture containing 10 to 90% water. By use of the transport data, permeation flux, separation selectivity, swelling index, and diffusion coefficients have been calculated. By increasing the grafting of the membrane, flux decreased, whereas separation selectivity increased slightly over that of pure PVA membrane. Arrhenius activation parameters for transport processes were calculated for 10 mass % water containing feed mixture by using flux and diffusion data obtained at 25, 35, and 45°C. Transport parameters were discussed in terms of sorption‐diffusion principles. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 4091–4097, 2004     

Induced Hydrophilicity of the Nanoclay on the Pervaporation Performance of Cross-Linked Poly(vinyl alcohol) Nanocomposite Membranes

In the present study, a novel poly(vinyl alcohol) membrane system was developed by a systematic approach for the pervaporation separation of water–isopropanol azeotropic mixtures. Poly(vinyl alcohol) with 5 vol% cross-linked membranes showed water permeance of 4166 gpu with intrinsic selectivity 47. To further enhance the separation efficiency a hydrophilic nanofiller, bentonite nanoclay, is reinforced with cross-linked poly(vinyl alcohol) (5 vol% glutraldehyde) membranes. The water permeance of the membranes increased to 8232 gpu, which is 100% more than that of cross-linked membranes. Membrane selectivity and the overall pervaporation performance also showed about 63 and 157% increment, respectively.     

Crosslinked blended poly(vinyl alcohol)/N-methylol nylon-6 membranes for the pervaporation separation of ethanol–water mixtures

Crosslinked blended membranes of poly(vinyl alcohol) (PVA) and N-methylol nylon-6 were prepared either by thermal crosslinking at 180°C or by chemical crosslinking with maleic acid. The pervaporation performance for the separation of ethanol–water mixtures of these membranes was investigated in terms of feed concentration, PVA content, and crosslinking agent content. The pervaporation performance of two differently crosslinked membranes was strongly influenced by the nature of the crosslinkage. Significant improvement in the pervaporation separation index can be achieved for chemically crosslinked membranes. From the comparison between the pervaporation and sorption tests, it is suggested that, for hydrophilic membranes, sorption properties dominate the pervaporation performance at feed solutions of higher water content, while diffusion properties govern at feed solutions of higher ethanol content. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 317–327, 1998     

Pervaporation separation of isopropanol–water mixtures using mixed matrix blend membranes of poly(vinyl alcohol)/poly(vinyl pyrrolidone) loaded with phosphomolybdic acid

Mixed matrix membranes of poly(vinyl alcohol) and poly(vinyl pyrrilidone) blends were prepared by loading with phosphomolybdic acid (PMA) and their pervaporation (PV) properties were investigated for the PV separation of isopropanol. Membrane performance shown a dependence on the extent of PMA loading. The 4 wt % PMA‐loaded blend membrane had the highest separation factor of 29991, which declined considerably at higher loading. The flux of 4 wt % PMA‐loaded membrane was lower than that of nascent blend membrane. Feed water composition and temperature influenced the PV performance. Solubility selectivity was higher than diffusion selectivity. Degree of swelling was smaller after PMA loading exhibiting better separation ability. The PV results were analyzed using the Flory‐Huggins theory and sorption was dominated by Langmuir's mode. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Pervaporation separation and swelling measurement of acetic acid-water mixtures using crosslinked PVA membranes

The pervaporation separation and the swelling behavior of acetic acid-water mixtures were investigated at 30, 40, and 50°C using the crosslinked poly(vinyl alcohol) (PVA) membranes with varying the poly(acrylic acid) (PAA) contents and the acetic acid concentration in the feed mixture. Typically, for the pervaporation separation of 90 wt % acetic acid in the feed, the PVA/PAA = 75/25 membrane gives the separation factor of 795 and the flux of 5.6 g/m² h at 30°C, respectively. The swelling degree decreases as the PAA content in the membrane decreases to 20 wt % of PAA due to the increase of the crosslinking portion in the membrane and increases beyond this PAA content. The swelling degrees show fairly high at the operating temperatures and the total range of the liquid mixtures in question. The overall activation energy of permeation was also calculated using an Arrhenius type relationship. From this study, it could be concluded that the diffusion step is dominant over the sorption step. © 1997 John Wiley & Sons, Inc.