The reaction in water of UF resins with isocyanates at short curing times: A 13C NMR investigation

CP MAS ¹³C NMR spectra of hardened resins have shown that urethane bridges derived from the reaction of the isocyanate group with the hydroxymethyl group of urea do form even at fast curing times comparable to what was used in the wood panels industry, in lower proportions than what was shown earlier. Polyureas and biurets obtained from the reaction of isocyanate with water are the predominant crosslinking reactions of pMDI alone and in UF/pMDI resin systems under fast curing conditions. Residual, unreacted isocyanate groups in the hardened network are consistently observed. Their proportion markedly decreases when the original proportion of urea–formaldehyde (UF) resin is high and that of pMDI is low. Under these fast curing conditions, the UF resin appears to self‐condense through an unusually high proportion of methylene ether links rather than methylene bridges alone. A marked proportion of residual, unreacted hydroxymethyl groups is also noticeable, initially, in the UF self‐condensation network. Direct NMR tests on thin hardboard bonded under fast pressing conditions with different proportions of UF/pMDI confirmed that crosslinking due to polyureas and biurets formation are predominant in the crosslinking of pMDI when alone and in UF/pMDI resin systems. They confirmed that residual, unreacted isocyanate groups are present in the finished panel. Their proportion is higher when the proportion of pMDI in the system is high. The presence or absence of urethanes could not be confirmed directly on the panels as the relevant peaks are masked by the wood carbohydrates signals of wood cellulose and hemicelluloses. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1624–1632, 2006     

13C NMR investigation of the reaction in water of UF resins with blocked emulsifiable isocyanates

A solid state ¹³C NMR study of hardened networks obtained by the reaction of blocked and nonblocked isocyanates (pMDI) with urea‐formaldehyde (UF) resins in water showed different results according to the temperature of the reaction. At high temperature, in water, both a nonblocked or an emulsifiable, blocked isocyanate, appear to crosslink with UF resins through the formation both of traditional methylene bridges connecting urea to urea and of urethane bridges. The latter have been confirmed by ¹³C NMR to form in water by reaction of the isocyanate ? N?C?O group with the hydroxymethyl groups of the UF resin. At ambient temperature, UF/pMDI resins where the pMDI is a emulsifiable blocked isocyanate, do not appear to form urethanes to any great extent but rather to crosslink through the usual UF resin urea to urea methylene bridges. Even in this case, when urethane bridges appear to be absent, evidence of crosslinking in water through reaction of the isocyanate with the ? NH₂ and ? NH? amide of the UF resin has not been observed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 589–596, 2006     

Hydrolytic stability of cured urea‐formaldehyde resins modified by additives

Urea‐formaldehyde (UF) resins are prone to hydrolysis that results in low‐moisture resistance and subsequent formaldehyde emission from UF resin‐bonded wood panels. This study was conducted to investigate hydrolytic stability of modified UF resins as a way of lowering the formaldehyde emission of cured UF resin. Neat UF resins with three different formaldehyde/urea (F/U) mole ratios (1.4, 1.2, and 1.0) were modified, after resin synthesis, by adding four additives such as sodium hydrosulfite, sodium bisulfite, acrylamide, and polymeric 4,4′‐diphenylmethane diisocyanate (pMDI). All additives were added to UF resins with three different F/U mole ratios before curing the resin. The hydrolytic stability of UF resins was determined by measuring the mass loss and liberated formaldehyde concentration of cured and modified UF resins after acid hydrolysis. Modified UF resins of lower F/U mole ratios of 1.0 and 1.2 showed better hydrolytic stability than the one of higher F/U mole ratio of 1.4, except the modified UF resins with pMDI. The hydrolytic stability of modified UF resins by sulfur compounds (sodium bisulfate and sodium hydrosulfite) decreased with an increase in their level. However, both acrylamide and pMDI were much more effective than two sulfur compounds in terms of hydrolytic stability of modified UF resins. These results indicated that modified UF resin of the F/U mole ratio of 1.2 by adding acrylamide was the most effective in improving the hydrolytic stability of UF resin. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Improving the properties of ionic liquid-treated lignin-urea-formaldehyde resins by a small addition of isocyanate for wood adhesive

The aim of this research was to investigate the effect of polymeric 4, 4 diphenyl methane diisocyanate (pMDI) on the physical and mechanical properties of plywood panels bonded with an ionic liquid (IL)-treated lignin-urea-formaldehyde resin. Soda lignin modified by 1-ethyl-3-methylimidazolium acetate ([Emim][OAc]) IL was added to a urea formaldehyde (UF) resin during resin synthesis to prepare a lignin-urea-formaldehyde (LUF) resin. pMDI at various contents (2, 4, and 6% on resin solids) was then added to prepare a LUF resin. The thermal and physicochemical properties of the resins prepared as well as the water absorption, shear strength, and formaldehyde emission of the plywood panels bonded with them were measured according to standard methods. DSC analysis indicated that the addition of pMDI decreases the gel onset and curing temperatures of the LUF resin. According to the results obtained, the addition of pMDI significantly increased the viscosity and solid content and accelerated the gelation time of LUF resins. Based on the findings of this research, the addition of pMDI dramatically improves the performance of LUF resins as a new adhesive for wood-based panels. The LUF resins with isocyanate added yielded panels presenting lower formaldehyde emission and lower water absorption content when compared to those bonded with the control LUF resins. Greater dry and wet shear strength can be obtained by a small addition of pMDI to LUF resins.     

Microcrystallinity and colloidal peculiarities of UF/isocyanate hybrid resins

Combined mixtures of polymeric diphenylmethane diisocyanates (pMDI) with Urea‐formaldehyde‐resins (UF) adhesives for wood panels are shown (a) by X‐ray diffraction analysis (XRD) of the cured adhesive to present a certain percentage of microcrystallinity, this being due exclusively to the proportion of urea‐formaldehyde resin present in the mix and, (b) by polarized light optical microscopy (PLOM) to present colloidal structures in which oligomers and colloidal structures of one resin have migrated within the colloidal structures of the other resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2633–2636, 2007     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. V

The effects of posttreatments of particleboard adhesive‐type urea–formaldehyde resins were studied. The resins were synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.40, 1.60, 1.80, 2.10, and 2.40 and then the second urea was added to give a final formaldehyde/urea ratio of 1.15 in alkaline pH. The resins were posttreated at 60°C for up to 13.5 h and the 2.5‐h heat‐treated resin samples were stored at room temperature for up to 27 days. Resins sampled during the posttreatments were examined by ¹³C‐NMR and evaluated by bonding particleboards. In the posttreatments, hydroxymethyl groups on the polymeric resin components dissociated to formaldehyde and reacted with the second urea, and methylene and methylene–ether groups were formed from reactions involving the second urea. Methylene–diurea and urea groups bonded to UF polymers were identified. As a result, the viscosity of the resins initially decreased but later increased along with the cloudiness of the resins. Bond‐strength and formaldehyde‐emission values of particleboard varied with posttreatment variables as well as with the F/U₁ mol ratios used in the resin syntheses. The results would be useful in optimizing resin synthesis and handling parameters. Various reaction mechanisms were considered. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1896–1917, 2003     

Melamine‐bridged alkyl resorcinol modified urea–formaldehyde resin for bonding hardwood plywood

A powdery product was obtained by the reaction of methylolated melamine with alkyl resorcinols to form melamine‐bridged alkyl resorcinols (MARs). The effects of the addition of this powder on the bonding strength and formaldehyde emission of urea–formaldehyde (UF) resins were investigated. Three types of UF resins with a formaldehyde/urea molar ratio of 1.3 synthesized by condensation at pH 1.0 (UF‐1.0), pH 4.5 (UF‐4.5), and pH 5.0 (UF‐5.0) were fabricated. The addition of MAR to UF‐4.5 and UF‐5.0 for bonding hardwood plywood enhanced the bonding strength and reduced formaldehyde emission. For UF‐1.0, the addition of MAR adversely affected the bonding strength. However, the UF‐1.0 resin yielded the lowest formaldehyde emission of all of the UF resins in the study. The effects of the MAR addition were related to the molecular structures of the UF resins. UF‐1.0 contained a large amount of free urea, a considerable number of urons, and a highly methylene‐linked, ring‐structured higher molecular weight fraction and had a smaller number of methylol groups. Therefore, the addition of MAR was considered to cause a shortage of the methylol groups, which in turn, led to incomplete resin curing. In contrast to UF‐1.0, UF‐5.0 contained a smaller amount of free urea and a linearly structured higher molecular weight fraction and had a larger number of methylol groups. In this case, MAR was considered to effectively react with the methylol groups to develop a three‐dimensional crosslinked polymer network to enhance the bonding strength and suppress the generation of free formaldehyde to reduce formaldehyde emission. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Modification of urea-formaldehyde resin adhesives with blocked isocyanates using sodium bisulfite

Polymeric 4-4 diphenyl methane diisocyanate (pMDI) was blocked with an aqueous sodium bisulfite solution to obtain water-dispersible blocked pMDI (B-pMDI) resin with different HSO₃/–NCO mole ratios for the modification of urea-formaldehyde (UF) resin. Fourier transform infrared (FTIR) spectra of the B-pMDI resin clearly showed that all isocyanate groups of the pMDI resin were successfully blocked by sodium bisulfite. As the HSO₃/–NCO mole ratio increased, the de-blocking temperature of the B-pMDI resin also increased. Two addition levels (1% and 3%) of the B-pMDI resin with different HSO₃/–NCO mole ratios were mixed with UF resins and used as an adhesive for plywood. The gel time of the UF/B-pMDI resins decreased to a minimum at a mole ratio of 0.9 and then increased with the HSO₃/–NCO mole ratio, and was consistent with the peak temperature (Tp). However, as the HSO₃/–NCO mole ratio increased, the viscosity of the modified UF resins by 1% B-pMDI resin addition slightly increased, whereas those of modified resins with 3% B-pMDI resin addition rapidly increased. The adhesion strengths of plywood bonded with the hybrid resins were greater for 1% B-pMDI resin addition than for 3% B-pMDI resin addition. Formaldehyde emission of plywood bonded with the UF/B-pMDI resins significantly decreased up to 34% by the addition of B-pMDI resin at a mole ratio of 1.8. These results suggest that the modification of UF resins by mixing with water-dispersible B-pMDI resin can be a method for improving the water resistance and formaldehyde emission of UF resins for wood-based composites.     

Study of hybrid isocyanate and high-mono-hydroxymethyl urea content urea-formaldehyde resins

Based on the difference in the reaction rate of different groups of urea-formaldehyde resins and isocyanate resins, this study designed two different urea-formaldehyde resins: a normal urea-formaldehyde resin (UF) and one with high mono-hydroxymethylurea content (UF*) to react with polymeric methylene diphenyl diisocyanate (pMDI) resin. The difference in mono- and di-hydroxymethyl urea content between UF and UF* resins was analyzed by nuclear magnetic resonance (NMR) spectroscopy, and results showed that the mono-hydroxymethyl urea content of the UF* resin was much higher than that of the conventional UF resin. The fourier transform infrared spectrometer (FTIR) analysis of differences between UF* and UF resin showed that the UF* process did not change the main structure of the conventional urea formaldehyde resin. Differential scanning calorimeter (DSC) analysis showed that the curing temperature of the hybrid UF*-pMDI resin was reduced 27.3°C compared to that of the UF-pMDI resin. When these hybrid resins were used to bond plywood respectively, test results showed that the UF*-pMDI resin improved the dry and wet bonding strength by 2.6% and 3.9%, respectively, compared with the UF-pMDI resin under the condition of hot pressing time (3 min) and temperature (140°C), meeting the requirement of Chinese standard of GB/T 9846–2015 for Class III board. This study provides a new path for further improving the performance and design of hybrid resins based on isocyanate and urea-formaldehyde resin.     

Synthesis and properties of multihydroxy soybean oil from soybean oil and polymeric methylene‐diphenyl‐ 4,4′‐diisocyanate/multihydroxy soybean oil polyurethane adhesive to wood

The reactive multihydroxy soybean oil (MHSBO) was synthesized from epoxidized soybean oil (ESBO). The ESBO was reacted with ethylene glycol to obtain MHSBO having high functionality. This study investigated a feasibility to prepare wood adhesive through the reaction of polymeric methylene‐diphenyl‐4,4′‐diisocyanate (pMDI) with MHSBO. Different polyurethane adhesives were prepared with a variety of equivalent mole ratios (eq. mole ratios) of MHSBO to pMDI. The chemical reactions of adhesives were analyzed using ¹H NMR and Fourier transform infrared (FTIR), and their thermal studies were investigated by DSC and TGA. The MHSBO/pMDI resins (3 : 1 and 2 : 1 eq. mole ratios) showed endothermic peaks, whereas the MHSBO/pMDI resins (1 : 2 and 1 : 3 eq. mole ratios) showed exothermic peaks. The best adhesion strength was found when plywood was bonded with the adhesive of a eq. mole ratio of 2 : 1 (MHSBO : pMDI). These results indicated that the bond strength was not related to the reactivity obtained from the FTIR spectra. But it was explained that the adhesion strength increased as the residual  NCO groups in the adhesive reacted with the hydroxy groups of wood during the manufacturing of plywood. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Examination of selected synthesis and room‐temperature storage parameters for wood adhesive‐type urea–formaldehyde resins by 13C‐NMR spectroscopy. IV

Typical particleboard wood‐adhesive urea–formaldehyde (UF) resins, synthesized with formaldehyde/first urea (F/U₁) mol ratios of 1.80, 2.10, and 2.40 and the second urea added to an overall F/U ratio of 1.15, in weak alkaline pH, were allowed to stand at room temperature over a period of 50 days. ¹³C‐NMR of time samples taken over the storage period showed gradual migration of hydroxymethyl groups from the polymeric first‐urea components to the monomeric second‐urea components and also an advancing degree of polymerization of resins by forming methylene and methylene ether groups involving the second urea. These phenomena that varied with the F/U₁ mol ratios used in the resin syntheses due to the varying polymer branching structures resulted in the first step of resin synthesis. Varying viscosity decreases and increases of the resins also occurred. Due to these chemical and physical changes, the particleboards that bonded with the sampled resins showed varying bond strength and formaldehyde‐emission values, indicating process optimizations possible to improve bonding and formaldehyde‐emission performances. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1155–1169, 2001     

Comparative 13C‐NMR and matrix‐assisted laser desorption/ionization time‐of‐flight analyses of species variation and structure maintenance during melamine–urea–formaldehyde resin preparation

The preparation of an industrially used sequential formulation of a melamine–urea–formaldehyde resin was followed by matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry and ¹³C‐NMR analysis. The analysis allowed us to identify and follow the appearance, increase, decrease, and disappearance of a multitude of chemical species during the preparation of both the initial urea–formaldehyde (UF) phase of the reaction and the subsequent reaction of melamine with the UF resin that formed. The analysis indicated that (1) the increase and decrease in the species that formed proceeded through a cycle of the formation and degradation of species occurring continuously through what appeared to be a series of complex equilibria, (2) even at the end of the reaction a predominant proportion of methylene ether bridges was still present, (3) some small proportion of methylene bridges already had formed in the UF reaction phase of the resin even under rather alkaline conditions, and (4) the addition of melamine to the UF prepolymer induced some noticeable rearrangement of methylene ether bridges to methylene bridges. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Sustainable phenolic thermosets coatings derived from urushiol

The over-exploitation of finite fossil resources and/or the increased environmental and sustainable awareness inspire scientists and technologists to search for inexpensive alternatives from renewable chemicals. Phenol formaldehyde (PF) resins, the oldest type of synthetic polymers with good mechanical properties and heat resistance, are widely used in the production of coatings, laminates, molding compositions, and glues. Here, biobased urushiol-derived PF resins were synthesized from the alkali-catalyzed reaction between urushiol and formaldehyde. The chemical compositions and molecular structures of resole resins were characterized by carbon-13 nuclear magnetic resonance and Fourier transform infrared spectroscopy, and their curing behaviors were studied by differential scanning calorimetry. The as-prepared urushiol-derived resole resins had methylol (Ph−CH₂OH), ortho- and para-hemiformal groups (Ph−CH₂OCH₂OH), and the para−para/ortho−para/ortho−ortho links of methylene groups (Ph−CH₂−Ph), whereas the resole resins had low curing temperatures at about 100–113°C. Additionally, given the long side alkyl group moiety on the aromatic rings of urushiol, the films of cured urushiol-derived resole resins had low glass transition temperatures of 132 ± 2°C. Furthermore, the as-prepared urushiol-derived coatings exhibited excellent physical and mechanical properties.     

Influence of glyoxal on curing of urea-formaldehyde resins

In the present paper, the effect of glyoxal on the gel formation within the adhesive systems based on urea-formaldehyde (UF) resins is shown. A reduction of formaldehyde content in wood-based panels by decreasing the formaldehyde/urea molar ratio in the UF resins leads to increasing of the UF resin gel time, and impairing the qualitative characteristics of the UF-based wood materials. Glyoxal is shown to speed up the crosslinking of the macromolecules as well as significant reduction of gel time of adhesive composition. The first reason is the result of reaction between glyoxal and ammonium ion leading to protons releasing. Another reason is that glyoxal and its interaction products react with macromolecules of the UF resin forming a three-dimension cross-linked structure. The gel time and the pot life of the UF resin are measured by the oscillatory viscometer. Formation of the UF cross-linked resin structure with glyoxal and a curing catalyst (ammonium sulfate) is studied using dispersion Raman scattering spectroscopy. Particleboards (PB) are produced using different amount of glyoxal and formaldehyde/urea molar ratio in the UF resin. The properties are evaluated according to the European Standards and include density, internal bond, thickness swelling moisture content and formaldehyde content.     

13C‐NMR, 13C‐13C gCOSY,and ESI‐MS characterization of ether‐bridged condensation products in N,N′‐dimethylurea‐formaldehyde systems

The reaction of urea with formaldehyde is the basis for the production of urea‐formaldehyde (UF) resins which are widely applied in the wood industry. The presence of ether‐bridged condensation products in the UF resin reaction system is an open question in the literature. It is addressed in the present work. The N,N′‐dimethylurea‐formaldehyde model system was studied since it is chemically similar to the UF resin reaction system but allows for a simple elucidation of all reaction products. It was analyzed by ¹³C‐NMR spectroscopy and ESI‐MS. In corresponding NMR and MS spectra, peaks due to methoxymethylenebis(dimethyl)urea and its hemiformal were observed. ¹³C‐¹³C gCOSY analysis was conducted using labeled ¹³C‐formaldehyde. The correlation spectra showed evidence for an ether‐bridged compound and mass spectra exhibited peaks agreeing with labeled methoxymethylenebis(dimethyl)urea and its hemiformal. Methoxymethylenebis(dimethyl)urea was characterized in N,N′‐dimethylurea‐formaldehyde systems in acidic and slightly basic media. As urea is very similar to N,N′‐dimethylurea, the results of this work strengthen the assumption that ether‐bridged condensation products are likely to form in UF resins. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Uron and uron–urea‐formaldehyde resins

The favored pH ranges for the formation of urons in urea‐formaldehyde (UF) resins preparation were determined, these being at pH's higher than 6 and lower than 4 at which the equilibrium urons ↔ N,N′‐dimethylol ureas are shifted in favor of the cyclic uron species. Shifting the pH slowly during the preparation from one favorable range to the other causes shift in the equilibrium and formation of a majority of methylol ureas species, whereas a rapid change in pH does not cause this to any great extent. UF resins in which uron constituted as much as 60% of the resin were prepared and the procedure to maximize the proportion of uron present at the end of the reaction is described. Uron was found to be present in these resins also as linked by methylene bridges to urea and other urons and also as methylol urons, the reactivity of the methylol group of this latter having been shown to be much lower than that of the same group in methylol ureas. Thermomechanical analysis (TMA) tests and tests on wood particleboard prepared with uron resins to which relatively small proportions of urea were added at the end of the reaction were capable of gelling and yielding bonds of considerable strength. Equally, mixing a uron‐rich resin with a low F/U molar ratio UF resin yielded resins of greater strength than a simple UF of corresponding molar ratio indicating that UF resins of lower formaldehyde emission with still acceptable strength could be prepared with these resins. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 277–289, 1999     

Study of glycidyl ether as a new kind of modifier for urea‐formaldehyde wood adhesives

In this work, the multiepoxy functional glycidyl ether (GE) modified urea‐formaldehyde (UF) resins were synthesized via a traditional alkaline‐acid process under low formaldehyde/urea (F/U) molar ratio. The synthesized resins were characterized by ¹³C magnetic resonance spectroscopy (¹³C‐NMR), indicating that GE can effectively react with UF resins via the ring‐opening reaction of epoxy groups. Moreover, the residual epoxy groups of GE could also participate in the curing reaction of UF resins, which was verified by Fourier transform infrared spectroscopy. The storage stability of GE‐modified UF resins and the thermal degradation behavior of the synthesized resins were evaluated by using optical microrheology and thermogravimetric analysis, respectively. Meanwhile, the synthesized resins were further employed to prepare the plywood with the veneers glued. For the modification on bonding strength and formaldehyde emission of the plywood, the influences of addition method, type, and amount of GE were systematically investigated. The performance of UF adhesives were remarkably improved by the modification of GE around 20–30% (weight percentage of total urea) in the acidic condensation stage during the resin synthesis. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Evaluation of melamine‐modified urea‐formaldehyde resins as particleboard binders

Particleboards bonded with 6 and 12% melamine‐modified urea‐formaldehyde (UMF) resins were manufactured using two different press temperatures and press times and the mechanical properties, water resistance, and formaldehyde emission (FE) values of boards were measured in comparison to a typical urea‐formaldehyde (UF) resin as control. The formaldehyde/(urea + melamine) (F/(U + M)) mole ratio of UMF resins and F/U mole ratio of UF resins were 1.05, 1.15, and 1.25 that encompass the current industrial values near 1.15. UMF resins exhibited better physical properties, higher water resistance, and lower FE values of boards than UF resin control for all F/(U + M) mole ratios tested. Therefore, addition of melamine at these levels can provide lower FE and maintain the physical properties of boards. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

13C‐NMR study on cure‐accelerated phenol‐formaldehyde resins with carbonates

Both liquid‐ and solid‐state carbon‐13–nuclear magnetic resonance (¹³C‐NMR) spectroscopies were used to investigate the cure acceleration effects of three carbonates (propylene carbonate, sodium carbonate, and potassium carbonate) on liquid and cured phenol‐formaldehyde (PF) resins. The liquid‐phase ¹³C‐NMR spectra showed that the cure acceleration mechanism in the propylene carbonate‐added PF resin seemed to be involved in increasing reactivity of the phenol rings, whereas the addition of both sodium carbonate and potassium carbonate into PF resin apparently resulted in the presence of ortho–ortho methylene linkages. Proton spin‐lattice rotating frame relaxation time (T_1ρH) measured by solid‐state ¹³C cross polarization/magic‐angle spinning NMR spectroscopy was smaller for the cure‐accelerated PF resins than that of the control PF resin. The result indicated that the cure‐accelerated PF resins are less rigid than the control PF resin. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 1284–1293, 2000     

Renewable polyol‐based polycarbamates and polycarbamate–formaldehyde thermosetting resins

Several polycarbamates and polycarbamate–formaldehyde (CF) resins were synthesized, and their properties were investigated aiming at developing of useful thermosetting polymer materials from simple polyols including those derived from renewable resources. Polycarbamates synthesized from polyols using two‐step laboratory routes showed good storage stabilities making them suitable as large volume industrial chemicals. Furthermore, syntheses and ¹³C‐NMR studies of CF resins showed the formation of oligomeric resins having hydroxymethyl and methylene groups with thermosetting curing properties that are similar to those of current urea–formaldehyde (UF) resins. Dynamic mechanical analysis studies showed somewhat slower curing rates for CF resins compared to UF resins. Bonding of particleboard and internal bond and free formaldehyde content measurements indicated high‐bond strength values and very low‐formaldehyde emission potentials for CF resins. The higher functionalities of CF resins appear to be the basis of good performances. Further investigations on scalable synthesis methods for polycarbamates and on the expansion of CF resins' bonding capabilities would need to be investigated in the future. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011