Compatibility of polysaccharide/maleic copolymer blends. IV. Thermal behavior of hydroxypropyl cellulose‐containing blends

The compatibility of the hydroxypropyl cellulose (HPC) with maleic acid–vinyl acetate copolymer in the solid state was studied by thermogravimetry, thermo‐optical analysis, differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FTIR), and optical microscopy. It was established that physical interactions are prevalent in blends with a high content of HPC, whereas chemical interactions predominate in blends with a medium and low content of HPC. By increasing the temperature, the thermochemical reactions are favored. Thermal properties are dependent on the mixing ratio of the components. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2585–2597, 2003     

Phthalonitrile‐epoxy blends: Cure behavior and copolymer properties

Binary blends composed of 4,4′‐bis(3,4‐dicyanophenoxy)biphenyl (biphenyl PN) and diglycidyl ether of bisphenol A (epoxy resin) and oligomeric n = 4 phthalonitrile (n = 4 PN) and epoxy resin were prepared. The cure behavior of the blends was studied under dynamic and isothermal curing conditions using differential scanning calorimetry, simultaneous thermogravimetric/differential thermal analysis, infrared spectroscopy, and rheological analysis. The studies revealed that phthalonitrile‐epoxy blends exhibited good processability and that they copolymerized with or without the addition of curing additive. In the absence of curing additive, the blends required higher temperatures and longer cure times. The thermal and dynamic viscoelastic properties of amine‐cured phthalonitrile‐epoxy copolymers were examined and compared with those of the neat epoxy resin. The properties of the epoxy resin improved with increasing biphenyl PN content and with n = 4 PN addition. Specifically, the copolymers exhibited higher glass transition temperatures, increased thermal and thermo‐oxidative stabililty, and enhanced dynamic mechanical properties relative to the commercially available epoxy resin. The results showed that the phthalonitrile‐epoxy blends and copolymers have an attractive combination of processability and high temperature properties. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of monomethyl itaconate‐grafted HDPE and EPR on the compatibility and properties of HDPE–EPR blends

To improve the compatibility and properties of blends based on high‐density polyethylene (HDPE) and the ethylene–propylene copolymer (EPR), the functionalization of both through grafting with an itaconic acid derivative, monomethyl itaconate (MMI), was investigated. The grafting reaction was performed at 180°C in a Brabender Plasticorder using an initial monomer concentration of 3 phr in the case of HDPE and 5 phr in the case of EPR. 2,5‐Dimethyl‐2,5‐bis(tert‐butylperoxy)hexane was used as a radical initiator for the functionalization of HDPE and dicumyl peroxide was used as a radical initiator for the modification of EPR. The degree of grafting was 1.56% by weight for HDPE and 0.8% by weight for EPR. The effect of grafting on the processability, morphology, and thermal and mechanical properties of the blends are of particular interest. The results show that the grafting reaction increases the toughness and elongation at break of all tested blends and they retained their strength and stiffness. Moreover, the grafted polymers behaved as nucleating agents, accelerating the HDPE crystallization. These results are particularly relevant when both polymeric phases are modified. Morphological studies are in concordance with the mechanical characterization, showing a reduction of the rubber particle size and a better interfacial adhesion when both polymers are functionalized with MMI. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2239–2248, 2003     

聚合物共混相容性研究进展

介绍了聚合物共混相容性的热力学理论，讨论了相容性的实验表征方法，包括共混物形态和物性表征等，提出了改善聚合物相容性的重要途径及其进展。     

Thermal,thermo‐mechanical,and dynamic mechanical properties of polypropylene/cycloolefin copolymer blends

Interaction of the components and physical properties of the polypropylene (PP)/cycloolefin copolymer (COC) blends were studied by means of differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), Vicat softening temperature (VST), and measurements of the coefficient of linear thermal expansion (CLTE) and of the density. The attention was focused on the blends with 90–60% of PP by wt, where the COC minority component was present in the form of short fibers. DSC, DMTA, and density measurements concurrently prove the immiscibility of PP and COC. DSC measurements reveal that crystallinity and melting temperature of the PP component slightly decrease with the fraction of COC in blends, in the range of 56–47% and 164–161°C, respectively. Storage modulus and loss modulus of the blends are in a good accord with the model predictions based on (i) the equivalent box model (EBM) and on (ii) modified equations of the percolation theory. The dependence of the VST on the blend composition is in a good correlation with the previous morphological analysis. Measurements of the coefficient of thermal expansion provide useful data as the functions of temperature and blend composition. Density of the blends was found to obey the volume additivity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Thermal stability of polycaprolactone/Nafion blends prepared in the presence of 3‐aminopropyltriethoxysilane

Polycaprolactone (PCL) and Nafion blends were prepared in the presence of 3‐aminopropyltriethoxysilane (3‐APTEOS) by a sol–gel reaction. The presence of 3‐APTEOS allowed the preparation of macroscopically homogeneous self‐supported films of PCL/Nafion blends in a wider composition range. The thermal properties of the blends were evaluated by thermogravimetric analysis and differential scanning calorimetry. The thermal stability of the blends decreased as the Nafion content increased. The reduction of the thermal stability of PCL in the presence of Nafion was confirmed with Fourier transform infrared/photoacoustic spectroscopy, and it was attributed to the possible hydrolysis of PCL caused by the reaction with the SO₃H acid groups of Nafion. An opposite effect on the thermal stability of the blends was caused by the addition of 3‐APTEOS. The increase in the thermal stability of the blends with the increase in the 3‐APTEOS content was assigned to the neutralization of the acid groups of Nafion by the formation of an ionic complex. The differential scanning calorimetry results showed that PCL and Nafion were immiscible. The degree of crystallinity of PCL slightly increased with an increase in the Nafion content, whereas the melting temperature remained basically unchanged. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3701–3709, 2004     

Properties of soy protein isolate/poly(ethylene‐co‐ethyl acrylate‐co‐maleic anhydride) blends

Blends of soy protein isolate (SPI) with 10, 20, 30, 40, and 50% poly(ethylene‐co‐ethyl acrylate‐co‐maleic anhydride) (PEEAMA), with or without addition of 2.0 wt % methylene diphenyl diisocyanate (MDI), were prepared by mixing with an intensive mixer at 150°C for 5 min, and then milling through a 1‐mm sieve. Blends were then compression‐molded into a tensile bar at 140°C. Thermal and mechanical properties and water absorption of the blends were studied by differential scanning calorimetry (DSC), dynamical mechanic analysis (DMA), a test of modulus and tensile strength (with an Instron tensile tester), a water absorption test, and scanning electron microscopy (SEM). The blends showed two composition‐dependent glass transition temperatures. Furthermore, as the SPI content increased, the melting temperature of PEEAMA remained constant but the heat of fusion decreased. These results indicate that SPI and PEEAMA were partially miscible. Morphology observations support these results. Increasing the PEEAMA content resulted in decreases in the modulus and tensile strengths and increases in the elongation and toughness of the blends. Water absorption of the blends also decreased with increased PEEAMA content. Incorporating MDI further decreased the water absorption of the blends. The mechanism of water sorption of SPI was relaxation controlled, and that of the blends was diffusion controlled. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 407–413, 2003     

Effect of functionality levels and compatibility of polycarbonate blends with maleic anhydride grafted ABS

ABS was melt grafted with maleic anhydride at three different levels of 1, 2, and 3 wt %. These three different modified ABSs were melt blended with polycarbonate using a single‐screw extruder to choose a suitable maleic anhydride grafting level on ABS for better performance. For the compatibility study, binary blends of polycarbonate with ABS and maleic anhydride‐grafted ABS were prepared over the entire range of compositions. Compatibility of these blends was studied using a Dynamic Mechanical Analyzer and by Differential Scanning Calorimetry. Both techniques suggest more partial compatibility for modified blend systems. In addition to this, DSC thermograms show multiple peaks between the transition points of ABS fractions and polycarbonate fractions for the polycarbonate/maleic anhydride‐grafted ABS blends. These multiple peaks are characteristic of better partial compatibility with fine microstructure. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2102–2110, 1999     

Thermal behavior and properties of polystyrene/poly(methyl methacrylate) blends

The thermal behavior and properties of immiscible blends of polystyrene (PS) and poly(methyl methacrylate) (PMMA) with and without PS‐b‐PMMA diblock copolymer at different melt blending times were investigated by use of a differential scanning calorimeter. The weight fraction of PS in the blends ranged from 0.1 to 0.9. From the measured glass transition temperature (T_g) and specific heat increment (ΔC_p) at the T_g, the PMMA appeared to dissolve more in the PS phase than did the PS in the PMMA phase. The addition of a PS‐b‐PMMA diblock copolymer in the PS/PMMA blends slightly promoted the solubility of the PMMA in the PS and increased the interfacial adhesion between PS and PMMA phases during processing. The thermogravimetric analysis (TGA) showed that the presence of the PS‐b‐PMMA diblock copolymer in the PS/PMMA blends afforded protection against thermal degradation and improved their thermal stability. Also, it was found that the PS was more stable against thermal degradation than that of the PMMA over the entire heating range. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 609–620, 2004     

Rubber‐toughened PLA blends with low thermal expansion

In this study, poly (lactic acid) (PLA) blended with various rubber components, i.e., poly (ethylene‐glycidyl methacrylate) (EGMA), maleic anhydride grafted poly(styrene‐ethylene/butylene‐styrene) triblock elastomer (m‐SEBS), and poly(ethylene‐co‐octene) (EOR), was investigated. It was observed that EGMA is highly compatible due to its reaction with PLA. m‐SEBS is less compatible with PLA and EOR is incompatible with PLA. Electron microscopy (SEM and TEM) revealed that a fine co‐continuous microlayer structure is formed in the injection‐molded PLA/EGMA blends. This leads to polymer blends with high toughness and very low linear thermal expansion both in the flow direction and in the transverse direction. The microlayer thickness of rubber in PLA blends was found to play key roles in reducing the linear thermal expansion and achieving high toughness of the blends. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Enhancing the mechanical,morphological, and rheological behavior of polyethylene/polypropylene blends with maleic anhydride-grafted polyethylene

This is the first study to showcase the use of maleic anhydride-grafted polyethylene (MAPE) to compatibilize polyethylene (PE)-rich blends, where polypropylene (PP) represents the minor phase. By first mixing PP with MAPE, and then adding PE, MAPE was assumed to be localized at the PE/PP interface. Microscopy analysis confirmed that MAPE led to a remarkably fine PE/PP/MAPE morphology, with PP being uniformly dispersed into PE and having an average diameter 267% smaller than that in the PE/PP blend. According to mechanical and rheological tests, this translated into a 14%, 20%, and 14% enhancement of tensile strength, tensile modulus, and tensile toughness, respectively, as well as a 10% and 20% drop in PE/PP viscosity mismatch and interfacial tension, respectively. Finally, PE/PP/MAPE tensile toughness and elongation at break were greater than those of virgin PP, while PE/PP/MAPE strength and stiffness were similar to the ones of neat PP. Therefore, this study provides industries with the possibility to utilize products rich in PE instead of those made of more expensive PP, while still keeping the level of performance high; hence, creating a paradigm shift in the development of advanced lightweight polyolefin materials with tuned functionalities.     

Morphology of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized by a methyl methacrylate/maleic anhydride copolymer

The morphologies of nylon 6/acrylonitrile–butadiene–styrene blends compatibilized with a methyl methacrylate/maleic anhydride copolymer, with 3–20 wt % maleic anhydride, were examined by transmission electron microscopy. Some staining techniques were employed for identifying the various phases. The binary blends were immiscible and exhibited poor mechanical properties that stemmed from the unfavorable interactions among their molecular segments. This produced an unstable and coarse phase morphology and weak interfaces among the phases in the solid state. The presence of the copolymer in the blends clearly led to a more efficient dispersion of the acrylonitrile–butadiene–styrene phase and consequently optimized Izod impact properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3512–3518, 2003     

Preparation and characterizations of RTV epoxy blends using amide maleic anhydride‐g‐liquid polybutadience as both reactive toughening and curing components

Amide maleic anhydride‐g‐liquid polybutadience (AMALPB) was synthesized using maleic anhydride‐g‐liquid polybutadience (MALPB) with ethylenediamine (EDA), and its structure was confirmed by FTIR and ¹H‐nuclear magnetic resonance spectra, respectively. It was then used as a reactive toughening agent to make blends with diglycidyl end‐capped poly(bisphenol‐A‐co‐epichlorohydrin epoxy cured at room temperature. Their thermal decomposing behaviors did not show much difference because both EDA and AMALPB possessed similar aliphatic groups. All their glass transition temperatures (T_g) increased more than 10 °C than that of the neat epoxy, and with the addition of AMALPB, the blends were greatly strengthened upon heating as show from their storage moduli. When AMALPB was added at 10 wt %, its elongation at break increases to a maximum of 8.8% which was about two times higher than that of the neat epoxy, and its tensile strength also increased. However, the excessive addition of AMALPB resulted in an apparent decline in their tensile strength at content above 20%. The simultaneous improvements in both tensile strength and strain were attributed to the existence of well‐dispersed rubber particles in the continuous matrices performing plastic deformation that resulted from the chemical bonds of interfaces among the rubber particles and matrix, and meanwhile, inducing the deflection of the cracks. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45985.     

Dynamic rheological and morphological study of the compatibility of thermoplastic polyurethane/ethylene–octene copolymer blends

Two grafted ethylene–octene copolymers [POEs; i.e., POE‐g‐maleic anhydried (MAH) and aminated POE (denoted by POE‐g‐NH₂) were used as compatibilizers in immiscible blends of thermoplastic polyurethane (TPU) and POE. The effects of the compatibilizers on the dynamic rheological properties and morphologies of the TPU/POE blends were investigated. The characteristic rheological behaviors of the blends indicated that the strong interactions between the two phases were due to the compatibilization. Microstructural observation confirmed that the compatibilizers were located at the interface in the blends and formed a stable interfacial layer and smaller dispersed phase particle size. Compared with POE‐g‐MAH, POE‐g‐NH₂ exhibited a better compatibilization effect in the TPU/POE blends. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Thermal and mechanical properties of linear low‐density polyethylene/low‐density polyethylene/wax ternary blends

The thermal and mechanical properties of uncrosslinked three‐component blends of linear low‐density polyethylene (LLDPE), low‐density polyethylene (LDPE), and a hard, paraffinic Fischer–Tropsch wax were investigated. A decrease in the total crystallinity with an increase in both LDPE and wax contents was observed. It was also observed that experimental enthalpy values of LLDPE in the blends were generally higher than the theoretically expected values, whereas in the case of LDPE the theoretically expected values were higher than the experimental values. In the presence of higher wax content there was a good correlation between experimental and theoretically expected enthalpy values. The DSC results showed changes in peak temperature of melting, as well as peak width, with changing blend composition. Most of these changes are explained in terms of the preferred cocrystallization of wax with LLDPE. Young's modulus, yield stress, and stress at break decreased with increasing LDPE content, whereas elongation at yield increased. This is in line with the decreasing crystallinity and increasing amorphous content expected with increasing LDPE content. Deviations from this behavior for samples containing 10% wax and relatively low LDPE contents are explained in terms of lower tie chain fractions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1748–1755, 2005     

Blends of thermoplastic polyurethane and polypropylene. II. Thermal and morphological behavior

Neat thermoplastic polyurethane (TPU), polypropylene (PP), and TPU/PP blends with different weight ratios that were prepared in a twin‐screw extruder were investigated with differential scanning calorimetry and light and scanning electron microscopy. The results confirmed PP matrix to TPU matrix phase inversion in the concentration region between 60/40 and 80/20 TPU/PP blends. The total degree of crystallinity of the blends and the crystallization temperature of PP decreased with increasing TPU content. On the other hand, the addition of elastomeric TPU to PP significantly increased the spherulite size of PP. The TPU melt islands in the PP matrix prolonged the crystallization of PP during solidification, and this enhanced the growth of spherulites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Compatibilized blends of PVC/PA12 and PVC/PP containing poly(lauryl lactam‐block‐caprolactone)

Specially designed block copolymers have played a role as compatibilizing agents in the system of immiscible polymer blends. We applied lauryl lactam (LA)–caprolactone (CL) block copolymer [P(LA‐b‐CL)] as a compatibilizing agent for immiscible poly(vinyl chloride) (PVC) blends with various polymers. These blends possess high thermal performance and toughness. We investigated the effect of P(LA‐b‐CL) as a compatibilizing agent for immiscible PVC blends with poly(ω‐lauryl lactam) [polyamide 12 (PA12)]. We also described the invention of a new compatibilizing agent system involving P(LA‐b‐CL) for PVC/polypropylene (PP) blends. The mechanical and thermal properties of (1) PVC/PA12 blend compatibilized with P(LA‐b‐CL) and (2) PVC/PP blend compatibilized with P(LA‐b‐CL)/PA12/maleic anhydride–modified PP were both enhanced. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1983‐1992, 2004     

Morphology and thermal properties of liquid crystal p‐PAEB/styrene copolymer

The homopolymer of unsaturated liquid crystal (LC) monomer for p‐phenylene di {4‐[2‐(allyloxy) ethoxy] benzoate} (p‐PAEB), and copolymer poly (p‐PAEB/St) of p‐PAEB with styrene (St) have been synthesized. The LC behavior and thermal properties of p‐PAEB and poly(p‐PAEB/St) have been studied by Polarizing Optical Microscopic (POM), Differential Scanning Calorimetry, X‐Ray Diffractometer (XRD), and Torsional Braid Analysis (TBA). The results demonstrate that LC phase texture and phase transition temperature of copolymers are affected by the composition of LC units in copolymers. The POM and XRD reveal that p‐PAEB has a smectic phase structure; the copolymer of p‐PAEB with styrene reveal deformed focal conics texture of smectic phase. The phase transition temperature range of p‐PAEB is 120.5–191.5°C, but the homopolymer of p‐PAEB has a broad LC temperature range from 77 to 170°C. The LC temperature range of poly(p‐PAEB/St) is broadened with increased content of p‐PAEB. The dynamic mechanical properties of LC polymer networks were investigated with TBA. The results indicate that the peak temperature of maximal mechanical loss is 114°C and is decreased with the addition of styrene © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5731–5736, 2006     

Thermal and mechanical properties of silicon rubber/cis‐polybutadiene rubber/ethylene–propylene–diene monomer blends

Considering the properties of silicon rubber, ethylene–propylene–diene monomer (EPDM), and cis‐polybutadiene rubber (BR), a blend made by a new method was proposed in this article; this blend had thermal resistance and good mechanical properties. The morphology of the blend was studied by SEM, and it was found that the adhesion between the phases of BR, EPDM, and polysiloxanes (silicon rubber) could be enhanced, and the compatibility and covulcanization were good. The influence of the mass ratio of peroxide and silica on the mechanical properties and thermal resistance of the blend was studied. The results showed that the mechanical properties and thermal resistance of the blend were improved when silicon rubber/BR/EPDM was 20/30/50, dicumyl peroxide/sulfur was 2.5/2.5, and the amount of silica was 80 phr. The integral properties of rubber blend had more advantages than did the three rubbers. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 4462–4467, 2006     

Studies on the engineering properties of LCP‐Vectra B 950/PP blends with the variations of EAA content

Polypropylene (PP) was melt blended with Vectra B‐950 [a thermotropic liquid crystalline polymer (LCP)], in a single screw extruder in presence of different doses of ethylene acrylic acid (EAA) copolymer, as modifier. The effect of incorporation in different proportions of EAA at a fixed dose of 5% LCP, on mechanical, thermal, morphological, and rheological properties of such blends was studied and the same were compared with that of pure PP and amongst themselves. Mechanical analysis (tensile properties) of the prepared blends exhibited improvements in ultimate tensile strength (UTS), modulus, toughness, hardness, and impact strength of PP matrix with the incorporation of EAA. The improvement in mechanical properties is associated with the formation of LCP fibrils as evidenced by scanning electron microscopy (SEM). A strong interaction through H‐bonding between the segments of Vectra B‐950 and EAA was established by FTIR study. Differential scanning calorimetry (DSC) studies indicated substantial increase in melting point of the blends, and thermogravimetric analysis (TGA) showed that the thermal stability of PP was improved with the addition of LCP and EAA. Rheological properties showed that LCP and EAA drop down the melt viscosity of PP and thus facilitate processibility of blends. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011