High molecular weight poly (L‐lactic acid) clay nanocomposites via solid‐state polymerization

We propose here, a novel technique to synthesize high molecular weight (MW) poly (L ‐lactic acid)‐clay nanocomposite (PLACN), via solid state polymerization (SSP). We synthesize prepolymer of PLACN (pre‐PLACN) from both, L ‐lactic acid and L ‐lactide, as starting materials. Synthesis of pre‐PLACN from L ‐lactic acid is carried out via in situ melt polycondensation (MP) of L ‐lactic acid oligomer, followed by SSP, to achieve high MW PLACN (M_w ∼ 138,000 Da). In case of L ‐lactide as the starting material, we prepare L ‐lactide–clay intercalated mixture which yields moderate MW pre‐PLACN during subsequent ring opening polymerization (ROP). Interestingly, ROP is performed by using hydroxyl functionalized ternary catalyst system (L ‐lactide–Sn(II) octoate–oligo (L‐lactic acid) complex), which provides the terminal hydroxyl end‐groups, required for step‐growth SSP. Pre‐PLACN MW is now increased to M_w ∼ 127,000 Da, by the subsequent SSP process. ¹H NMR analyses confirm that these end‐groups, are indeed consumed during SSP. During SSP, the PLACN also achieves up to 90% crystallinity, which may be due to the synchronization of the slow step‐growth SSP of poly(L ‐lactic acid) (PLA) with the crystallization kinetics. Optical purity of PLACNs is similar to that of neat PLA, whereas the thermal stability of PLACNs is significantly superior. As evidenced by wide‐angle X‐ray scattering/small‐angle X‐ray scattering analyses and in line with the literature, both, intercalated and exfoliated PLACN morphologies, have been synthesized, by suitable selection of clays. We also verify the correlation between the PLA semicrystalline morphology and the PLACN morphology, which is consistent with those of PLACN synthesized by other techniques. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers     

Influence of racemization on stereocomplex‐induced gelation of water‐soluble polylactide–poly(ethylene glycol) block copolymers

Ring‐opening polymerization of L ‐ or D ‐lactide was realized at 140 °C for a period of 7 days in the presence of dihydroxyl poly(ethylene glycol) (PEG), with M?_n = 4000 g mol^?1, using zinc lactate as initiator. The resulting poly(L ‐lactide)–PEG–poly(L ‐lactide) and poly(D ‐lactide)–PEG–poly(D ‐lactide) triblock copolymers are water soluble with polylactide (PLA) block length ranging from 11 to 17 units. Both the tube inverting method and rheological measurements were used to evaluate the gelation properties of aqueous solutions containing single copolymers or L /D copolymer pairs. Stereocomplexation between poly(L ‐lactide) and poly(D ‐lactide) blocks is observed for mixed solutions. Hydrogel formation is detected in the case of relatively long PLA blocks (DP _PLA = 17), but not for copolymers with shorter PLA blocks (DP _PLA = 11–13) due to partial racemization of L ‐lactyl units. Racemization is largely reduced when the reaction time is shortened to 1 day. Under these conditions, DP _PLA of 8 is sufficient for the stereocomplexation of PLA–PEG block copolymers, and DP _PLA above 10 leads to the formation of hydrogels of PLA–PEG block copolymers. On the other hand, racemization appears as a general phenomenon in the (co)polymerization of L ‐lactide with Zn(Lac)₂ as initiator, although it is negligible or undetectable in the case of high molar mass polymers. Therefore, racemization is the limiting factor for the stereocomplexation‐induced gelation of water‐soluble PLA–PEG block copolymers where the PLA block length generally ranges from 10 to 30. Reaction conditions including initiator, time and temperature should be strictly controlled to minimize racemization. Copyright © 2010 Society of Chemical Industry     

Synthesis and characterization of poly(L‐lactide‐co‐ϵ‐caprolactone)‐b‐poly(L‐lactide) biodegradable diblock copolyesters: Effect of the block lengths on their thermal properties

Poly(L ‐lactide‐co‐ε‐caprolactone)‐b‐poly(L ‐lactide) [P(LL‐co‐CL)‐b‐PLL] diblock copolyesters were synthesized in a two‐step process with 1‐dodecanol (DDC) and stannous octoate as the initiating system. In the first‐step reaction, a 50:50 mol % amorphous poly(L ‐lactide‐co‐ε‐caprolactone) [P(LL‐co‐CL)] copolyester was synthesized via the bulk copolymerization of L ‐lactide and ε‐caprolactone, which was followed by the polymerization of the PLL crystalline block at the end chain in the second‐step reaction. The yielded copolyesters were characterized with dilute‐solution viscometry, gel permeation chromatography, ¹H‐ and ¹³C‐NMR, and differential scanning calorimetry methods. The molecular weights of the P(LL‐co‐CL) copolyesters from the first‐step reaction were controlled by the DDC concentrations, whereas in the second‐step reaction, the molecular weights of the P(LL‐co‐CL)‐b‐PLL diblock copolyesters depended on the starting P(LL‐co‐CL) copolyester molecular weights and L ‐lactide/prepolymer molar ratios. The starting P(LL‐co‐CL) copolyester molecular weights and PLL block lengths seemed to be the main factors affecting specific thermal properties, including the melting temperature (T_m), heat of melting (ΔH_m), crystallizing temperature (T_c), and heat of crystallizing (ΔH_c), of the final P(LL‐co‐CL)‐b‐PLL diblock copolyester products. T_m, ΔH_m, T_c, and ΔH_c increased when the PLL block lengths increased. However, these thermal properties of the diblock copolyesters also decreased when the P(LL‐co‐CL) block lengths increased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Microstructure and Thermal Properties of Polylactides with Different L‐ and D‐Unit Sequences: Importance of the Helical Nature of the L‐Sequenced Segments

A series of polylactides (PLA) with different stereo sequences are prepared by the copolymerization of L ‐lactide and DL ‐lactide. It is confirmed that the glass transition temperature (T_g) of the PLA decreases with decreasing optical purity of the lactate units (%ee) according to the Fox's equation. Analysis of the FT‐IR spectra of these PLA samples reveals that the absorbance at 1 265 cm^?1 (δCH + νCOC) decreases with increasing L ‐content while the absorbance at 1 210 cm^?1 (ν_asCOC + r_asCH₃) increases with increasing L ‐content. These changes in absorbance are reasonably correlated with the randomness and helical nature of the L ‐sequenced segments involved in PLA. Namely, the PLA chains with higher L ‐content comprise a higher number of short helical blocks that are made of several L ‐lactate units. This difference in helical nature causes the opposite dependences of T_g and density on the L ‐content of PLA; i.e., the increased T_g and decreased density with increasing L ‐content.

FT‐IR spectra of a PDLLA film, NO‐PLLA, and BO‐PLLA.     

Preparation and characterization of magnetic star‐shaped amphiphilic copolymer nanoparticles of S‐Fe3O4‐PLA‐b‐MPEG

Magnetic star‐shaped amphiphilic copolymers (S‐Fe₃O₄‐PLA‐b‐MPEG) consisting of Fe₃O₄ as the core, poly(L ,D ‐lactide) (PLA) as the inner layer, and monomethyl polyethylene glycol (MPEG) as the out shell were synthesized. The syntheses included ring‐opening polymerization of L ,D ‐lactide initiated by hydroxyl modified Fe₃O₄ (Fe₃O₄‐(OH) _n), followed by the esterification of the PLA with MPEG. The structure of the star block copolymers were characterized by Fourier Transform infrared spectroscopy, thermogravimetric analysis, X‐ray diffraction, transmission electron microscopy, nanoparticle size analyzer, and vibrating sample magnetometer. The nanoparticles in aqueous solution were made from the amphiphilic star copolymer. The average size of the nanoparticles was adjustable and increased with the increase of the PLA segments in the copolymer. The cytotoxicity grade of the nanoparticles was zero determined by the analysis of cytotoxicity. The nanoparticles could potentially be used as the drug vehicles for magnetic‐response controlled release. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Microwave‐irradiated ring‐opening polymerization of D,L‐lactide under atmosphere

Poly(D ,L ‐lactide) (PDLLA) was synthesized by microwave‐irradiated ring‐opening polymerization catalyzed by stannous octoate (Sn(Oct)₂) under atmosphere. The effects of heating medium, monomer purity, catalyst concentration, microwave irradiation time, and vacuum level were discussed. Under the appropriate conditions such as carborundum (SiC) as heating‐medium, 0.15% catalyst, lactide with purity above 99.9%, 450 W microwave power, 30 min irradiation time, and atmosphere, PDLLA with a viscosity–average molecular weight (M_η) over 2.0 × 10⁵ and a yield over 85% was obtained. The dismission of vacuum to ring‐opening polymerization of D ,L ‐lactide (DLLA) under microwave irradiation simplified the process greatly. The temperature under microwave irradiation and conventional heating was compared. The largely enhanced ring‐opening polymerization rate of DLLA under microwave irradiation was the coeffect of thermal effects and microwave effects. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2244–2247, 2006     

Plasticization of Poly‐L‐lactide with L‐lactide,D‐lactide,and D,L‐lactide monomers

Poly‐L ‐lactide (PLLA) is being widely considered for repair of damaged tissues, for controlled antibiotic release, and also as scaffolds for cultured cells. PLLA was blended with the lactide monomer in its two enantiomeric forms: D ‐lactide (D ‐la) and L ‐lactide (L ‐la) and with the cyclic dimmer D ,L ‐la, in order to enhance its flexibility and thereby overcome its inherent problem of brittleness. In this work, the crystallization, phase structure, and tensile properties of PLLA and PLLA plasticized with 5, 10, 15, and 20 wt% of D ‐la, L ‐la, and D ,L ‐la are explored. The three plasticizers used were effective in lowering the glass transition temperature (T_g) and the melting temperature (T_m) of PLLA, around 20°C for a plasticizer content of 20 wt%. The tensile strength and modulus of the blends decreased following the increasing content of plasticizers from approximately 58 MPa to values below 20 MPa, and from 1667 to 200 MPa, respectively. Aging the blends at storage ambient temperature revealed that the enhanced flexibility as well as the morphological stability was lost over time due to the migration of the plasticizer to the surface, this being less marked in the case of D ‐la as a result of interactions between the polymer and its enantiomeric monomer of complementary configuration. POLYM. ENG. SCI., 53:2073–2080, 2013. © 2013 Society of Plastics Engineers     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of AB‐type copolymers poly(L‐lactide)‐block‐poly(methyl methacrylate) via a convenient route combining ROP and ATRP from a dual initiator

Diblock copolymers of poly(L ‐lactide)‐block‐poly(methyl methacrylate) (PLLA‐b‐PMMA) were synthesized through a sequential two‐step strategy, which combines ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP), using a bifunctional initiator, 2,2,2‐trichloroethanol. The trichloro‐terminated poly(L ‐lactide) (PLLA‐Cl) with high molecular weight (M_n,GPC = 1–12 × 10⁴ g/mol) was presynthesized through bulk ROP of L ‐lactide (L ‐LA), initiated by the hydroxyl group of the double‐headed initiator, with tin(II) octoate (Sn(Oct)₂) as catalyst. The second segment of the block copolymer was synthesized by the ATRP of methyl methacrylate (MMA), with PLLA‐Cl as macroinitiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalyst, and dimethyl sulfoxide (DMSO) was chosen as reaction medium due to the poor solubility of the macroinitiator in conventional solvents at the reaction temperature. The trichloroethoxyl terminal group of the macroinitiator was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy. The comprehensive results from GPC, FTIR, ¹H‐NMR analysis indicate that diblock copolymers PLLA‐b‐PMMA (M_n,GPC = 5–13 × 10⁴ g/mol) with desired molecular composition were obtained by changing the molar ratio of monomer/initiator. DSC, XRD, and TG analyses establish that the crystallization of copolymers is inhibited with the introduction of PMMA segment, which will be beneficial to ameliorating the brittleness, and furthermore, to improving the thermal performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of ABA type tri‐block copolymers derived from p‐dioxanone,L‐lactide and poly(ethylene glycol)

A series of triblock co‐polymers, consisting of a poly(ethylene glycol) (PEG) central block joined to two blocks of random p‐dioxanone‐co‐L ‐lactide copolymers were synthesized by ring‐opening polymerization of p‐dioxanone (PDO) and L ‐lactide (LLA) initiated by PEG in the presence of stannous 2‐ethylhexanoate catalyst. The resulting copolymers were characterized by various techniques including ¹H and ¹³C NMR and FTIR spectroscopies, gel permeation chromatography, inherent viscosity, wide‐angle X‐ray diffractometry (WAXD) and differential scanning calorimetry (DSC). The conversion of PDO and L ‐lactide into the polymer was studied various mole ratios and at different polymerization temperature from ¹H NMR spectra. Results of WAXD and DSC showed that the crystallinity of PEG macroinitiator was greatly influenced by the composition of PDO and L ‐lactide in the copolymer. The triblock copolymers with low molecular weight were soluble in water at below room temperature. © 2003 Society of Chemical Industry     

Synthesis,characterization and biocompatibility of novel biodegradable poly[((R)‐3‐hydroxybutyrate)‐block‐(D,L‐lactide)‐block‐(ε‐caprolactone)] triblock copolymers

BACKGROUND: Biodegradable block copolymers have attracted particular attention in both fundamental and applied research because of their unique chain architecture, biodegradability and biocompatibility. Hence, biodegradable poly[((R )‐3 ‐hydroxybutyrate)‐block‐(D ,L ‐lactide)‐block‐(ε‐caprolactone)] (PHB‐PLA‐PCL) triblock copolymers were synthesized, characterized and evaluated for their biocompatibility. RESULTS: The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and thermogravimetric analysis showed that the novel triblock copolymers were successfully synthesized. Differential scanning calorimetry and wide‐angle X‐ray diffraction showed that the crystallinity of PHB in the copolymers decreased compared with methyl‐PHB (LMPHB) oligomer precursor. Blood compatibility experiments showed that the blood coagulation time became longer accompanied by a reduced number of platelets adhering to films of the copolymers with decreasing PHB content in the triblocks. Murine osteoblast MC3T3‐E1 cells cultured on the triblock copolymer films spread and proliferated significantly better compared with their growth on homopolymers of PHB, PLA and PCL, respectively. CONCLUSION: For the first time, PHB‐PLA‐PCL triblock copolymers were synthesized using low molecular weight LMPHB oligomer as the macroinitiator through ring‐opening polymerization with D ,L ‐lactide and ε‐caprolactone. The triblock copolymers exhibited flexible properties with good biocompatibility; they could be developed into promising biomedical materials for in vivo applications. Copyright © 2008 Society of Chemical Industry     

Particle size and distribution of biodegradable poly‐D,L‐lactide‐co‐poly(ethylene glycol) block polymer nanoparticles prepared by nanoprecipitation

A biodegradable block copolymer, poly‐D ,L ‐lactide (PLA)‐co‐poly(ethylene glycol) (PEG), was prepared by the ring‐opening polymerization of lactide with stannous caprylate [Sn(Oct₂)] as a catalyst; then, the PLA–PEG copolymer was made into nanoparticles by nanoprecipitation under different conditions. The average molecular weight and structure of PLA–PEG were detected by ¹H‐NMR and gel permeation chromatography. The sizes and distributions of the nanoparticles were investigated with a laser particle‐size analyzer. The morphologies of the nanoparticles were examined by transmission electron microscopy. The effects of the solvent–nonsolvent system, operation conditions, and dosage of span‐80 on the sizes and distributions of the nanoparticles are discussed. The results show that acetone–water was a suitable solvent–nonsolvent system and the volume ratio of the nonsolvent phase to the solvent phase (O/W) (v/v), the concentration of PLA–PEG in the solvent phase, and the dosage of span‐80 had important effects on the particle sizes and distributions. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1884–1890, 2005     

Synthesis and characterization of an amphiphilic hyperbranched poly(amine‐ester)‐co‐D,L‐lactide (HPAE‐co‐PLA) copolymers and their nanoparticles for protein drug delivery

A series of hyperbranched poly(amine‐ester)‐co‐D ,L ‐lactide (HPAE‐co‐PLA) copolymer were synthesized by ring‐opening polymerization of D ,L ‐lactide with Sn(Oct)₂ as catalyst to a fourth generation branched poly(amine‐ester) (HPAE‐OHs4). The chemical structures of copolymers were determined by FTIR, ¹H‐NMR, ¹³C‐NMR, and TGA. Double emulsion (DE) and nanoprecipitation (NP) method were used to fabricate the nanoparticles of these copolymers encapsulating bovine serum albumin (BSA) as a model. DSC thermo‐grams indicated that the nanoparticles with BSA kept stable below 40°C. Different factors which influence on particular size and encapsulation efficiency (EE) were investigated. Their EE to BSA could reach 97.8% at an available condition. In vitro release behavior of NPs showed a continuous release after a burst release. The stability maintenance of BSA in the nanoparticle release in vitro was also measured via circular dichroism and fluorescence spectrometry. The results showed that the copolymer nanoparticles have a promising potential in protein delivery system. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation of porous poly(D,L‐lactide) and poly(D,L‐lactide‐co‐glycolide) membranes by a phase inversion process and investigation of their morphological changes as cell culture scaffolds

Porous membranes composed of the biodegradable polyesters poly(D,L ‐lactide) (PLA) and poly(D,L ‐lactide‐co‐glycolide) (PLGA) were prepared by a phase inversion process. The molecular weights of the polymers and the concentrations of the polymer solutions affected the pore size and structure of the PLA and PLGA membranes. The molecular weights and morphological changes of the membranes as a function of time were investigated under incubation at 37°C in a humidified 5% CO₂ atmosphere. The pores that formed in the membranes changed dramatically with increasing time under these conditions. From the thermal characterization of the polymers in their dry and wet states, we found that the glass‐transition temperatures of PLA and PLGA affected morphological structure changes in the porous membranes. We also prepared a collagen‐coated membrane to improve the interaction between the cell and the substrate, and we observed that the collagen coating enhanced the attachment and growth of Chinese hamster ovary cells on the substrate. Finally, we found that only PLA was a suitable material to prepare a porous membrane scaffold with the phase inversion process with PLA, and a collagen coating was necessary for cell culture on the membrane. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2082–2092, 2004     

Biodegradable poly(ester‐ether)s: ring‐opening polymerization of D,L‐3‐methyl‐1,4‐dioxan‐2‐one using various initiator systems

The synthesis and detailed characterization of racemic 3‐methyl‐1,4‐dioxan‐2‐one (3‐MeDX) are reported. The bulk ring‐opening polymerization of 3‐MeDX, to yield a poly(ester‐ether) meant for biomedical applications, in the presence of various initiators such as tin(II) octanoate, tin(II) octanoate/n‐butyl alcohol, aluminium tris‐isopropoxide and an aluminium Schiff base complex (HAPENAlOⁱPr) under varying experimental conditions is here detailed for the first time. Polymerization kinetics were investigated and compared with those of 1,4‐dioxan‐2‐one. The studies reveal that the rate of polymerization of 3‐MeDX is less than that of 1,4‐dioxan‐2‐one. Experimental conditions to achieve relatively high molar masses have been established. Thermodynamic parameters such as enthalpy and entropy of 3‐MeDX polymerization as well as ceiling temperature have been determined. Poly(D ,L ‐3‐MeDX) is found to possess a much lower ceiling temperature than poly(1,4‐dioxan‐2‐one). Poly(D ,L ‐3‐MeDX) was characterized using NMR spectroscopy, matrix‐assisted laser desorption ionization mass spectrometry, size exclusion chromatography and differential scanning calorimetry. This polymer is an amorphous material with a glass transition temperature of about ?20 °C. Copyright © 2010 Society of Chemical Industry     

Ring‐opening graft polymerization of L‐lactide onto starch granules in an ionic liquid

A room temperature ionic liquid 1‐allyl‐3‐methylimidazolium chloride ([AMIM]Cl) was a promising direct solvent for starch and nonderivitizing solvent for starch‐effective dissolution, in which the ring‐opening graft polymerization (ROGP) of L ‐lactide (L ‐LA) onto starch chains was carried out homogeneously. The obtained starch grafted poly(L ‐lactide) (starch‐g‐PLLA) was characterized by FTIR, ¹³C NMR, DSC, and WAXD, and the good adhesion between the two components was evidenced by SEM observations although the chains of grafted PLLA were not long. The grafting efficiency of PLLA reached 30% when the ROGP proceeded at 100°C for 10 h with L ‐LA/starch 0.5 : 1 (wt/wt) and stannous octoate (Sn(Oct)₂) as a catalyst, which was calculated according to a standard curve newly created by FTIR method. The homopolymerization of L ‐LA and the disconnection of grafted PLLA from starch‐g‐PLLA were the main competition reactions. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of poly(ϵ‐caprolactone)–poly(L‐lactide) diblock copolymers with an organic amino calcium catalyst

The quasiliving characteristics of the ring‐opening polymerization of ?‐caprolactone (CL) catalyzed by an organic amino calcium were demonstrated. Taking advantage of this feature, we synthesized a series of poly(?‐caprolactone) (PCL)–poly(L ‐lactide) (PLA) diblock copolymers with the sequential addition of the monomers CL and L ‐lactide. The block structure was confirmed by ¹H‐NMR, ¹³C‐NMR, and gel permeation chromatography analysis. The crystalline structure of the copolymers was investigated by differential scanning calorimetry and wide‐angle X‐ray diffraction analysis. When the molecular weight of the PLA block was high enough, phase separation took place in the block copolymer to form PCL and PLA domains, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2654–2660, 2006     

Synthesis and characterization of ABA triblock and novel multiblock copolymers from ethylene glycol,L‐lactide,and ϵ‐caprolactone

Three types of copolymers were synthesized and characterized. First, triblock ABA copolymers [where A is a homopolymer of ?‐caprolactone and B is poly(ethylene glycol)] were prepared by the ring‐opening polymerization of poly(ethylene glycol) with ?‐caprolactone in the presence of stannous octoate (Sn(Oct)₂). The spectral, thermal, and mechanical properties of one sample of these copolymers were studied, and it was discovered that these types of copolymers were more hydrophilic, possessed lower melting points, and had superior mechanical properties (greater toughness) than poly(?‐caprolactone). Second, triblock ABA copolymers [where A is a homopolymer of L ‐lactide and B is poly(ethylene glycol)] were prepared by the ring‐opening polymerization of poly(ethylene glycol) with L ‐lactide in the presence of Sn(Oct)₂. The mechanical properties of these copolymers were studied, and it was found that they were tougher and softer than poly(L ‐lactide). Third, novel ABA triblock copolymers [where A is a copolymer of ?‐caprolactone and L ‐lactide and B is poly(ethylene glycol)] were prepared, and ¹H‐NMR and ¹³C‐NMR spectra of these copolymers indicated a microblock structure for the two end blocks. The stress–strain behavior revealed low yields and high toughness for these copolymers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2072–2081, 2002     

Self‐assembly and degradation of poly[(2‐methacryloyloxyethyl phosphorylcholine)‐block‐(D,L‐lactide)] diblock copolymers: large compound micelles to vesicles

Biodegradable poly[(2‐methacryloyloxyethyl phosphorylcholine)‐block‐(D ,L ‐lactide)] (PMPC‐b‐PLA) diblock copolymers with various hydrophilic PMPC weight fractions (f_PC) will spontaneously self‐assemble into well‐defined vesicles and large compound micelles (LCMs) in water. Transmission electron microscopy, scanning electron microscopy, dynamic light scattering and fluorescence microscopy were used to observe their aggregate morphologies. The degradation of the LCMs was investigated and the loss of molecular weight of PLA blocks was confirmed using ¹H NMR analysis. The hydrolysis of PLA increases f_PC and consequently shifts the preferred morphology from LCMs to vesicles. Such degradation‐induced morphological transitions mean that the biocompatible and biodegradable LCMs have great application potential in drug delivery. Copyright © 2010 Society of Chemical Industry     

Construct biomimetic giant vesicles via self‐assembly of poly(2‐methacryloyloxyethyl phosphorylcholine)‐block‐poly(D,L‐lactide)

The poly(2‐methacryloyloxyethyl phosphorylcholine)‐block‐poly(D ,L ‐lactide) (PMPC‐b‐PLA) was specially designed to develop biomimetic giant vesicles (GVs) and giant large compound vesicles via a simple spontaneous assemble in aqueous solution. The weight fraction of the hydrophilic PMPC block (f_PC) was proved to play an important role in the size and morphology control of the self‐assembled aggregates. The GVs with controlled micrometer size and biomimetic PMPC corona have great potential as artificial cell models. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010