Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007     

Synthesis and characterization of fullerene grafted poly(ε‐caprolactone)

The fullerene grafted poly(ε‐caprolactone) (PCL) was successfully synthesized with a graft efficiency of 80%. The fullerene moieties grafted onto the PCL chain aggregate into 1–2 μm particles so that a physical pseudo‐network is formed. Because of the existence of the network structure, the fullerene grafted PCL film can retain its shape at much higher temperatures than that of pure PCL film, as observed in dynamic mechanical tests. It shows a hydrophobic gelling behavior in chloroform solution. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and properties of electroconductive acrylonitrile grafted poly(vinyl alcohol) modified nembrane

PVA-g-AN was prepared, the yield and the graft efficiency were determined. A PVA-g-AN metal chelated film was then prepared by mixing and soaking methods, separately. After treatment with NaBH₄ aqueous solution or H₂S gas, the electrical and photoconductive properties were investigated. In order to increase the adsorption amount for metal ion in the soaking method, the amidoxime group was introduced into the PVA-g-AN film in various conditions. The proposed structures of the metal chelated PVA-g-AN films were also studied.     

Crystalline properties of poly(ε‐caprolactone)‐block‐poly(vinyl acetate) block copolymers: influence of synthesis route

Poly(ε‐caprolactone)‐block‐poly(vinyl acetate) (PCL‐b‐PVAc) block copolymers were synthesized using two approaches: a ‘coupling’ approach using click chemistry reaction and a ‘macroinitiator’ route. Different copolymers, varying by their block lengths, were prepared with both methods. PCL is a semi‐crystalline polymer, and consequently PCL blocks of PCL‐b‐PVAc are able to crystallize. The purpose of this work was to analyse the influence of the method of copolymer synthesis on the crystallinity of the PCL blocks. The results indicate a significant decrease of the crystallinity of the PCL blocks in copolymers obtained using the coupling method, compared to PCL homopolymers, in contrast to copolymers obtained through the macroinitiator approach for which the crystallinity of PCL is much less affected. This influence of the synthesis method is explained by the presence, in the copolymers obtained using the click reaction, of a rigid triazol cycle binding the two blocks, limiting their mobility and decreasing the tendency of PCL to crystallize. © 2013 Society of Chemical Industry     

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) as a compatibilizer for cellulose acetate/poly(ε‐caprolactone) blends

Poly(vinyl pyrrolidone‐co‐vinyl acetate)‐graft‐poly(ε‐caprolactone) (PVPVAc‐g‐PCL) was synthesized by radical copolymerization of N‐vinyl‐2‐pyrrolidone (VP)/vinyl acetate (VAc) comonomer and PCL macromonomer containing a reactive 2‐hydroxyethyl methacrylate terminal. The graft copolymer was designed in order to improve the interfacial adhesiveness of an immiscible blend system composed of cellulose acetate/poly(ε‐caprolactone) (CA/PCL). Adequate selections of preparation conditions led to successful acquisition of a series of graft copolymer samples with different values of molecular weight ( ), number of grafts (n), and segmental molecular weight of PVPVAc between adjacent grafts (M_n (between grafts)). Differential scanning calorimetry measurements gave a still immiscible indication for all of the ternary blends of CA/PCL/PVPVAc‐g‐PCL (72 : 18 : 10 in weight) that were prepared by using any of the copolymer samples as a compatibilizer. However, the incorporation enabled the CA/PCL (4 : 1) blend to be easily melt‐molded to give a visually homogeneous film sheet. This compatibilizing effect was found to be drastically enhanced when PVPVAc‐g‐PCLs of higher and M_n (between grafts) and lower n were employed. Scanning electron microscopy revealed that a uniform dispersion of the respective ingredients in the ternary blends was attainable with an assurance of the mixing scale of several hundreds of nanometers. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Radiation grafting of vinyl monomers onto poly(tetrafluoroethylene) powder produced by γ irradiation and properties of grafted poly(tetrafluoroethylene) filled low density polyethylene

Scrap poly(tetrafluoroethylene) (PTFE) was γ irradiated under an ambient atmosphere in order to produce extensive chain scission and oxidative degradation. After irradiation the PTFE was ground into a fine powder (2°‐PTFE) and grafted with styrene (St), vinyl acetate (VAc), and 4‐vinylpyridine (4‐VP) by using the direct irradiation technique. The grafted PTFE were then blended with low density polyethylene (LDPE). The study covered the characterization of irradiated PTFE and grafted 2°‐PTFE powder with various methods. Mechanical grinding was found to reduce trapped radicals formed during the irradiation process faster than the annealing process. Grafting on 2°‐PTFE was followed by gravimetric analysis, TGA, and the change in the particle size of the samples. Although we reached almost 20% grafting by weight in the St and 4‐VP monomers, VAc grafting was found to be maximum at around 8% by weight at the maximum absorbed dose. The addition of VAc grafted 2°‐PTFE into LDPE produced better final mechanical properties with a fine dispersion. However, as may be expected, the incorporation of the other two 2°‐PTFEs into LDPE showed low film quality and poor mechanical properties. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 816–826, 2001     

Preparation and characteristics of β-chitin and poly(vinyl alcohol) blend

Mechanical properties of blend films of β-chitin and poly(vinyl alcohol) (PVA) in dry and wet states were improved compared to those of homopolymers. Fourier transformed infra-red (FTi.r.) spectra of the blend showed the transition of hydroxyl and carbonyl stretching bands upon blending. The subtraction infra-red spectra of blend 70/30 indicated that the blend showed an intermolecular interaction and the reduction of crystallinity compared with those of pure β-chitin. Wide angle X-ray diffraction (WAXD) patterns of the blend also exhibited the loss of crystallinity of β-chitin and PVA upon blending. The blends, however, showed a mixed-crystal structure. Dielectric analysis of the blend showed the transition of α and β relaxation peaks of β-chitin upon blending, appeared at 182° and 97°, respectively. For blends, the temperature of the maximum loss (T_max) of β-chitin appeared at around 182° shifted to a lower temperature region. Differential scanning calorimetric analysis of the blend also showed the transition of melting endotherms of the blend. Transmission electron microscope (TEM) studies of blends using ruthenium tetraoxide as a staining agent were examined to reveal the micro-structure and miscibility of the blends. The TEM micrograph of blend 70/30 shows some microseparations, but it is still believed to be miscible in the blends.     

Characterization of degraded hydrogels based on poly(vinyl alcohol) grafted with poly(lactide‐co‐glycolide)

Poly(vinyl alcohol) (PVA) grafted with poly(lactide‐co‐glycolide) and cross‐linked as a material of increased hydrophobicity relative to PVA was produced. The properties were examined with respect to the mass loss, water uptake, hydrophilicity, and mechanical characteristics upon hydrolytical degradation. The hydrogels investigated display water uptake increasing with degradation time because of increasing hydrophilicity. The mass loss amounts up to 15% after eight weeks of degradation. The mechanical properties of the hydrogels are within the range of those of natural tissue, the E modulus is 18 MPa, or even 100–200 MPa, depending on the structure of material. The mechanical characteristic and their dependence degradation show the most recognizable correlation with the chemical structure. Studies of the topography of degraded samples (scanning electron microscopy) and IR measurements demonstrate the degradation to occur at slow rate due to the high degree of grafting. The mass loss is rather low and a bulk degradation mechanism takes place. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Miscibility of block copolymers of poly(ε‐caprolactone) and poly(ethylene glycol) with poly(3‐hydroxybutyrate) as well as the compatibilizing effect of these copolymers in blends of poly(ε‐caprolactone) and poly(3‐hydroxybutyrate)

Atactic poly(3‐hydroxybutyrate) (a‐PHB) and block copolymers of poly(ethylene glycol) (PEG) with poly(ε‐caprolactone) (PCL‐b‐PEG) were synthesized through anionic polymerization and coordination polymerization, respectively. As demonstrated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) measurements, both chemosynthesized a‐PHB and biosynthesized isotactic PHB (i‐PHB) are miscible with the PEG segment phase of PCL‐b‐PEGs. However, there is no evidence showing miscibility between both PHBs and the PCL segment phase of the copolymer even though PCL has been block‐copolymerized with PEG. Based on these results, PCL‐b‐PEG was added, as a compatibilizer, to both the PCL/a‐PHB blends and the PCL i‐PHB blends. The blend films were obtained through the evaporation of chloroform solutions of mixed components. Excitingly, the improvement in mechanical properties of PCL/PHB blends was achieved as anticipated initially upon the addition of PCL‐b‐PEG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2600–2608, 2001     

Synthesis and characterization of poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers by combined ring‐opening polymerization and cross‐coupling processes

2,5‐Dibromo‐1,4‐(dihydroxymethyl)benzene was used as initiator in ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate (Sn(Oct)₂) catalyst. The resulting poly(ε‐caprolactone) (PCL) macromonomer, with a central 2,5‐dibromo‐1,4‐diphenylene group, was used in combination with 1,4‐dibromo‐2,5‐dimethylbenzene for a Suzuki coupling in the presence of Pd(PPh₃)₄ as catalyst or using the system NiCl₂/bpy/PPh₃/Zn for a Yamamoto‐type polymerization. The poly(p‐phenylenes) (PPP) obtained, with PCL side chains, have solubility properties similar to those of the starting macromonomer, ie soluble in common organic solvents at room temperature. The new polymers were characterized by ¹H and ¹³C NMR and UV spectroscopy and also by GPC measurements. The thermal behaviour of the precursor PCL macromonomer and the final poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers were investigated by thermogravimetric analysis and differential scanning calorimetry analyses and compared. Copyright © 2004 Society of Chemical Industry     

Preparation and characterization of crosslinked polyurethane‐block‐poly(trifluoropropylmethyl)siloxane elastomers with potential biomedical applications

A series of crosslinked polyurethane‐block‐poly(trifluoropropylmethyl)siloxane elastomers were prepared via two steps. First, poly(trifluoropropylmethyl)siloxane polyurethane (FSPU) prepolymers were synthesized with α,ω‐bis(3‐aminopropyldiethoxylsilane) poly(trifluoropropylmethyl)siloxane (APFS) and toluenediisocyanate (TDI) and then capped with butanediol to generate the macromolecular FSPU diol extender. Second, polyurethane prepolymers synthesized from poly(tetramethylene oxide) and TDI were reacted with FSPU diol extenders with different ratios. The copolymers formed films through moisture curing and were characterized by Fourier transform infrared spectroscopy, DSC, dynamic mechanical analysis, TGA, mechanical testing etc. It is found that the equivalent ratio of reactants gives rise to a high molecular weight of copolymers and that low molecular weight APFS in the copolymers can form a certain number of silicon–oxygen crosslinks resulting from silicon alkoxy to produce higher tensile strength elastomers. The material thus has higher thermal stability and a more stable surface performance. The copolymers are then good candidates for biomedical applications.© 2013 Society of Chemical Industry     

Synthesis of poly(ester‐anhydride)s based on poly(ϵ‐caprolactone) prepolymer

The objective of this study was to prepare high molecular weight poly(ester‐anhydride)s by melt polycondensation. The polymerization procedure consisted of the preparation of carboxylic acid terminated poly(?‐caprolactone) prepolymers that were melt polymerized to poly(?‐caprolactone)s containing anhydride functions along the polymer backbone. Poly(?‐caprolactone) prepolymers were prepared using either 1,4‐butanediol or 4‐(hydroxymethyl)benzoic acid as initiators, yielding hydroxyl‐terminated intermediates that were then converted to carboxylic acid‐terminated prepolymers by reaction with succinic anhydride. Prepolymers were then allowed to react with an excess of acetic anhydride, followed by subsequent polycondensation to resulting high molecular weight poly(ester‐anhydride)s. Upon coupling of prepolymers, size exclusion chromatography analyses showed an increase from 3600 to 70,000 g/mol in number‐average molecular weight (M_n) for the 1,4‐butanediol initiated polymer, and an increase from 7200 to 68,000 g/mol for the 4‐(hydroxymethyl)benzoic acid‐initiated polymer. 4‐Hydroxybenzoic acid and adipic acid were also used as initiators in the preparation of poly(?‐caprolactone) prepolymers. However, with these initiators, the results were not satisfactory. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 176–185, 2001     

Preparation of poly(4‐vinylpyrrolidone)‐g‐poly(N‐hydroxyacrylamide) and study of its metal binding properties

Crosslinked poly(N‐vinylpyrrolidone), preirradiated in air with γ rays, was grafted with ethyl acrylate in dioxane and water. A detailed study of grafting was made under various reaction conditions. The graft copolymer was treated with potassium hydroxamate in ethanol. The resulting polymer contained pendant hydroxamic acid groups ( CO NHOH) and was studied for the formation of complexes with Fe(III), Cu(II), and Ni(II). The effect of pH on the metal ion uptake by the polymer was also studied. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 77: 475–483, 2000     

Largely improved tensile extensibility of poly(L‐lactic acid) by adding poly(ε‐caprolactone)

Poly(L ‐lactic acid) (PLLA) has good biocompatibility, biodegradability and physical properties. However, one of the drawbacks of PLLA is its brittleness due to the stiff backbone chain. In this work, a largely improved tensile toughness (extensibility) of PLLA was achieved by blending it with poly(ε‐caprolactone) (PCL). To obtain a good dispersion of PCL in the PLLA matrix, blends were prepared via a solution‐coagulation method. An increase in extensibility of PLLA of more than 20 times was observed on adding only 10 wt% of PCL, accompanied by a slight decrease in tensile strength. However, annealing of the samples led to a sharp decrease of extensibility due to phase separation and a change of crystalline structure. To conserve the good mechanical properties of PLLA/PCL blends, the blends were crosslinked via addition of dicumyl peroxide during the preparation process. For the crosslinked blend films, the extensibility was maintained nearly at the original high value even after annealing. Morphological analysis of cryo‐fractured and etched‐smoothed surfaces of the PLLA/PCL blends was carried out using scanning electron microscopy. Differential scanning calorimetry and polarized light microscopy experiments were used to check the possible change of crystallinity, melting point and crystal morphology for both PLLA and PCL after annealing. The results indicated that the combination of solution‐coagulation and crosslinking resulted in a good and stable dispersion of PCL in the PLLA matrix, which is considered as the main reason for the observed improvement of tensile toughness. Copyright © 2010 Society of Chemical Industry     

Toward environment‐friendly composites of poly(ε‐caprolactone) reinforced with stereocomplex‐type poly(l‐lactide)/poly(d‐lactide)

In this work, stereocomplex‐poly(l ‐ and d ‐lactide) (sc‐PLA) was incorporated into poly(ε‐caprolactone) (PCL) to fabricate a novel biodegradable polymer composite. PCL/sc‐PLA composites were prepared by solution casting at sc‐PLA loadings of 5–30 wt %. Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) demonstrated the formation of the stereocomplex in the blends. DSC and WAXD curves also indicated that the addition of sc‐PLA did not alter the crystal structure of PCL. Rheology and mechanical properties of neat PCL and the PCL/sc‐PLA composites were investigated in detail. Rheological measurements indicated that the composites exhibited evident solid‐like response in the low frequency region as the sc‐PLA loadings reached up to 20 wt %. Moreover, the long‐range motion of PCL chains was highly restrained. Dynamic mechanical analysis showed that the storage modulus (E′) of PCL in the composites was improved and the glass transition temperature values were hardly changed after the addition of sc‐PLA. Tensile tests showed that the Young's modulus, and yield strength of the composites were enhanced by the addition of sc‐PLA while the tensile strength and elongation at break were reduced. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40208.     

Miscible blends containing bacterial poly(3‐hydroxyvalerate) and poly(p‐vinyl phenol)

The miscibility of poly(3‐hydroxyvalerate) (PHV)/poly(p‐vinyl phenol) (PVPh) blends has been studied by differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy. The blends are miscible as shown by the existence of a single glass transition temperature (T_g) and a depression of the equilibrium melting temperature of PHV in each blend. The interaction parameter was found to be −1.2 based on the analysis of melting point depression data using the Nishi–Wang equation. Hydrogen‐bonding interactions exist between the carbonyl groups of PHV and the hydroxyl groups of PVPh as evidenced by FTIR spectra. The crystallization of PHV is significantly hindered by the addition of PVPh. The addition of 50 wt % PVPh can totally prevent PHV from cold crystallization. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 383–388, 1999     

Crystallization behavior of poly(ϵ‐caprolactone) in poly(ϵ‐caprolactone) and poly(vinyl methyl ether) mixtures

The morphological development and crystallization behavior of poly(?‐caprolactone) (PCL) in miscible mixtures of PCL and poly(vinyl methyl ether) (PVME) were investigated by optical microscopy as a function of the mixture composition and crystallization temperature. The results indicated that the degree of crystallinity of PCL was independent of the mixture composition upon melt crystallization because the glass‐transition temperatures of the mixtures were much lower than the crystallization temperature of PCL. The radii of the PCL spherulites increased linearly with time at crystallization temperatures ranging from 42 to 49°C. The isothermal growth rates of PCL spherulites decreased with the amount of the amorphous PVME components in the mixtures. Accounting for the miscibility of PCL/PVME mixtures, the radial growth rates of PCL spherulites were well described by a kinetic equation involving the Flory–Huggins interaction parameter and the free energy for the nuclei formation in such a way that the theoretical calculations were in good agreement with the experimental data. From the analysis of the equilibrium melting point depression, the interaction energy density of the PVME/PCL system was calculated to be ?3.95 J/cm³. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Part 7. Effects of poly(L‐lactide‐co‐ϵ‐caprolactone) on morphology,structure, crystallization,and physical properties of blends of poly(L‐lactide) and poly(ϵ‐caprolactone)

Blended films of poly(L ‐lactide) [ie poly(L ‐lactic acid)] (PLLA) and poly(?‐caprolactone) (PCL) without or mixed with 10 wt% poly(L ‐lactide‐co‐?‐caprolactone) (PLLA‐CL) were prepared by solution‐casting. The effects of PLLA‐CL on the morphology, phase structure, crystallization, and mechanical properties of films have been investigated using polarization optical microscopy, scanning electron microscopy, differential scanning calorimetry and tensile testing. Addition of PLLA‐CL decreased number densities of spherulites in PLLA and PCL films, and improved the observability of spherulites and the smoothness of cross‐section of the PLLA/PCL blend film. The melting temperatures (T_m) of PLLA and PCL in the films remained unchanged upon addition of PLLA‐CL, while the crystallinities of PLLA and PCL increased at PLLA contents [X_PLLA = weight of PLLA/(weight of PLLA and PCL)] of 0.4–0.7 and at most of the X_PLLA values, respectively. The addition of PLLA‐CL improved the tensile strength and the Young modulus of the films at X_PLLA of 0.5–0.8 and of 0–0.1 and 0.5–0.8, respectively, and the elongation at break of the films at all the X_PLLA values. These findings strongly suggest that PLLA‐CL was miscible with PLLA and PCL, and that the dissolved PLLA‐CL in PLLA‐rich and PCL‐rich phases increased the compatibility between these two phases. © 2003 Society of Chemical Industry