Effects of trans‐polyoctylene rubber on rheological and green tensile properties of natural rubber/acrylonitrile–butadiene rubber blends

The influence of trans‐polyoctylene rubber (TOR) on the flow property, die swell behaviour and green tensile property of NR (natural rubber)/NBR (acrylonitrile–butadiene rubber) blend compound was investigated as a function of TOR loading level. The pure TOR, NR and NBR compounds were also investigated for comparison with the blend compounds. The shear viscosity of TOR strongly depended on the temperature as well as shear rate. The viscosity of the NR/NBR blend compound was even lower than that of the constituent components at relatively lower shear rates, and the viscosity difference became smaller as the shear rate was increased. The viscosity of the NR/NBR blend compounds was strongly affected by the addition of TOR but the effect became negligible with increasing the shear rate. Both the die‐swell ratio and the surface topology of extrudates were also affected by TOR addition; the dependence on shear rate was much stronger for higher TOR level. The NR/NBR blend compound showed much higher green tensile strength and elongation at break than those of the constituent components. Both the green tensile modulus and strength of the NR/NBR blend compound were greatly enhanced, while the elongation at break was reduced with the addition of TOR. © 2002 Society of Chemical Industry     

Unsaturated polyester as compatibilizer for styrene–butadiene (SBR)/acrylonitrile–butadiene (NBR) rubber blends

The effect of the addition of 5 and 10 phr of unsaturated polyester resin (UPE) on the compatibility and physicomechanical properties of styrene–butadiene (SBR) and acrylonitrile–butadiene (NBR) rubber blends was studied. Differential scanning calorimetry (DSC), scanning electron microscopy (SEM), electrical, and ultrasonic techniques were used to determine the degree of the compatibility (DC). The results obtained revealed that, by the addition of 10 parts per hundred parts of rubber (phr) UPE as a compatibilizer for SBR/NBR blends, the degree of compatibility was greatly enhanced. The rheological and mechanical properties of the blends were also improved. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2314–2321, 2002     

Improvement of properties of silica‐filled styrene–butadiene rubber compounds using acrylonitrile–butadiene rubber

Since silica has strong filler–filler interactions and adsorbs polar materials, a silica‐filled rubber compound has a poor dispersion of the filler and poor cure characteristics. Improvement of the properties of silica‐filled styrene–butadiene rubber (SBR) compounds was studied using acrylonitrile–butadiene rubber (NBR). Viscosities and bound rubber contents of the compounds became lower by adding NBR to the compound. Cure characteristics of the compounds were improved by adding NBR. Physical properties such as modulus, tensile strength, heat buildup, abrasion, and crack resistance were also improved by adding NBR. Both wet traction and rolling resistance of the vulcanizates containing NBR were better than were those of the vulcanizate without NBR. The NBR effects in the silica‐filled SBR compounds were compared with the carbon black‐filled compounds. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1127–1133, 2001     

Effect of acrylic acid on the properties of recycled poly(vinyl chloride)/acrylonitrile–butadiene rubber blends

The effect of acrylic acid (AAc) on the torque, stabilization torque, mechanical energy, swelling behavior, mechanical properties, thermal stability, and morphological characteristics of recycled poly(vinyl chloride)/acrylonitrile–butadiene rubber (PVCr/NBR) blends was studied. The blends were melt mixed at a temperature of 150°C and rotor speed of 50 rpm. AAc was used to improve the compatibility of PVCr/NBR blends. Virgin PVCv/NBR blends were prepared to provide a comparison. It was found that PVCr/NBR + AAc blends exhibit higher stabilization torque, mechanical energy, stress at peak, and stress at 100% elongation, but lower elongation at break and swelling index than those of PVCr/NBR and PVCv/NBR blends. SEM study of the tensile fracture surfaces of the blends indicated that the presence of AAc increased the interfacial interaction between PVCr and NBR phases, thus improving the compatibility between PVCr and NBR phases. However, thermal gravimetry analysis of the blends showed that the presence of AAc decreased the thermal stability of PVCr/NBR blends. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2181–2191, 2005     

Styrene–butadiene rubber/natural rubber blends: Morphology,transport behavior,and dynamic mechanical and mechanical properties

Blends of styrene–butadiene rubber (SBR) and natural rubber (NR) were prepared and their morphology, transport behavior, and dynamic mechanical and mechanical properties were studied. The transport behavior of SBR/NR blends was examined in an atmosphere of n‐alkanes in the temperature range of 25–60°C. Transport parameters such as diffusivity, sorptivity, and permeability were estimated. Network characterization was done using phantom and affine models. The effect of the blend ratio on the dynamic mechanical properties of SBR/NR blends was investigated at different temperatures. The storage modulus of the blend decreased with increase of the temperature. Attempts were made to correlate the properties with the morphology of the blend. To understand the stability of the membranes, mechanical testing was carried out for unswollen, swollen, and deswollen samples. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1280–1303, 2000     

Fracture behaviour of acrylonitrile–butadiene rubber/clay nanocomposite

A new fracture behaviour is described for acrylonitrile–butadiene rubber/clay nanocomposite. The nanocomposite is prepared by melt mixing the organo‐treated montmorillonite into the rubber matrix, together with a peroxide curative, and crosslinked by conventional compression moulding for typical rubbers. A considerable enhancement in stiffness is observed without serious sacrifice in ultimate strength. A totally different tear morphology of a series of regularly‐spaced tear ridges parallel to the direction of tearing was observed instead of the typical ‘cross‐hatched morphology’ of conventional rubber composites. © 2001 Society of Chemical Industry     

Amelioration of acrylonitrile–butadiene copolymer properties using natural rubber graft p‐aminophenol

A two‐roll mill machine was used for the grafting of p‐aminophenol (pAP) onto natural rubber (NR). The prepared NR graft p‐aminphenol (NR‐g‐pAP) was characterized by ¹H NMR and IR spectroscopy techniques. The goal of this article is to study the effect of commercial antioxidants, N‐phenyl‐N′‐(1,3‐dimethylbutyl)‐p‐phenylenediamine (6PPD) and N‐phenyl‐N′‐isopropyl‐p‐phenylenediamine (IPPD), and the prepared NR‐g‐pAP, on the mechanical properties of acrylonitrile–butadiene (NBR) vulcanizates, the fluid compatibility of NBR vulcanizates, the hydraulic brake and clutch fluid dot, the diffusion out for NBR vulcanizate components, and the compression recovery of NBR vulcanizates. This study indicates that the NBR copolymer vulcanizate which contains the prepared NR‐g‐pAP has good protection against mechanical stress and the diffusion out of NBR vulcanizate components. The 6PPD and the prepared NR‐g‐pAP ameliorates the fluid compatibility of the oil seals, which is based on NBR as elastomer, and the hydraulic brake and clutch fluid dot. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Kaolin modified with sodium salt of rubber seed oil as a reinforcing filler for blends of natural rubber,polybutadiene rubber and acrylonitrile–butadiene rubber

Blends of natural rubber (NR) and synthetic rubbers are widely used in the rubber industry to meet specific performance requirements. Further, the emerging field of organomodified clay/rubber nanocomposites could provide a host of novel materials having a unique combination of properties to meet various stringent service conditions. Previous studies have shown that at very low dosages, china clay (kaolin) modified with sodium salt of rubber seed oil (SRSO) improved the cure characteristics and physico‐mechanical properties of NR. Results of the present study show improved cure characteristics and physico‐mechanical properties for blends of NR with butadiene rubber and nitrile rubber containing 4 phr of SRSO‐modified kaolin as indicated by reduction in optimum cure time along with higher tensile strength, tensile modulus and elongation at break for their vulcanizates as compared to those containing unmodified kaolin. The SRSO‐modified kaolin/rubber nanocomposites showed improved flex resistance, reduced heat build‐up, tan delta and loss modulus and higher chemical crosslink density index, indicating a reinforcing effect of the SRSO‐modified kaolin, enabling the nanocomposites to have potential industrial applications. © 2015 Society of Chemical Industry     

Structural morphology and properties of star styrene–isoprene–butadiene rubber and natural rubber/star styrene–butadiene rubber blends

Star styrene–isoprene–butadiene rubber (SIBR) was synthesized with a new kind of star anionic initiator made from naphthalene lithium and an SnCl₄ coupled agent. The relationship between the structure and properties of star SIBR was studied. Star block styrene–isoprene–butadiene rubber (SB‐SIBR), having low hysteresis, high road‐hugging, and excellent mechanical properties, was closer to meeting the overall performance requirements of ideal tire‐tread rubber according to a comparison of the morphology and various properties of SB‐SIBR with those of star random SIBR and natural rubber/star styrene–butadiene rubber blends. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 336–341, 2004     

Preparation and properties of acrylonitrile–butadiene copolymer hybrid nanocomposites with organoclays

Acrylonitrile–butadiene rubber (NBR) hybrid nanocomposites with organoclays were prepared by melt mixing, and their properties were compared with those of conventional rubber compounds filled with carbon black and silica. Based on X‐ray diffraction and transmission electron microscopy, the NBR nanocomposites obtained were found to form generally an intercalated structure, although they formed an exfoliated structure when the organoclay content was low enough, <2 parts per 100 rubber. The NBR nanocomposite showed a simultaneous improvement in ultimate strength and stiffness, which is generally in a trade‐off relation in rubbery materials. A characteristic fracture morphology of ‘laminated board‐type’ was observed for NBR nanocomposites instead of typical ‘cross‐hatched’ morphology in conventional rubber composites. The NBR nanocomposites also showed much higher hysteresis and tension set. Copyright © 2003 Society of Chemical Industry     

Mechanical properties and microstructure of acrylonitrile–butadiene rubber vulcanizates reinforced by in situ polymerized phenolic resin

The phenolic resin (PF) was incorporated into acrylonitrile–butadiene rubber (NBR) vulcanizates by in situ polymerization during the vulcanization process. It was found that the tensile strength, tearing strength, and tensile strength (300% elongation) could be considerably enhanced 59.4, 80.2, and 126.4%, respectively, at an optimum PF content of only 15 phr, but the elongation at break and shore A hardness were only slightly affected on the basis of silica‐reinforced NBR vulcanizates. A systematic study of the PF structure formed within the NBR matrix using various experimental schemes and procedures has revealed that the PF resin would form the localized discontinuous three‐dimensional interconnected network structures in the NBR matrix. The substantial reinforcement of PF on the mechanical properties of vulcanized NBR were attributed to the morphology, high flexibility, and moderate stiffness of the PF phases and their excellent bonding with rubbers through “rubber to rubber” and interface layer. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Cure characteristics,morphology, and mechanical properties of ethylene–propylene–diene–monomer rubber/acrylonitrile butadiene rubber blends

Blends based on ethylene–propylene–diene monomer rubber (EPDM) and acrylonitrile butadiene rubber (NBR) was prepared. Sulfur was used as the vulcanizing agent. The effects of blend ratio on the cure characteristics and mechanical properties, such as stress–strain behavior, tensile strength, elongation at break, hardness, rebound resilience, and abrasion resistance have been investigated. Tensile and tear strength showed synergism for the blend containing 30% of NBR, which has been explained in terms of morphology of the blends attested by scanning electron micrographs. A relatively cocontinuous morphology was observed for 70 : 30, EPDM/NBR blend system. The experimental results have been compared with the relevant theoretical models. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Thermal properties and morphology of isotactic polypropylene/acrylonitrile–butadiene rubber blends in the presence and absence of a nanoclay

A thermoplastic elastomer (TPE) nanocomposite based on polypropylene (PP), acrylonitrile–butadiene rubber (NBR), and a nanoclay (NC) was prepared in a laboratory mixer with a 54/40/6 weight ratio. The effects of NC on the thermal properties, crystalline structure, and phase morphology of the TPE nanocomposite were studied in this work. The results obtained from the nonisothermal crystallization of PP, PP/NBR, and PP/NBR/NC, which was carried out with differential scanning calorimetry, revealed that the overall rate of crystallization of PP decreased with the addition of NBR to PP and increased when NC was incorporated into the nanocomposite. In addition, the crystallite size distribution was more uniform for the PP phase crystallized in the nanocomposite versus the PP itself. Also, although the PP in the reference blend (PP/NBR) crystallized only in the α form, the crystalline structure of the PP incorporated into the nanocomposite was a mixture of α‐ and γ‐crystalline forms. The effects of NC on the phase morphology of PP/NBR blends prepared with three different cooling methods (quenching in liquid nitrogen, cooling between two metal plates at room temperature, and molding at a high temperature in a hot press) were studied. For the samples quenched in liquid nitrogen or cooled between metal plates, a particulate–cocontinuous morphology formed. However, for the samples prepared under a hot press, a laminar‐like morphology was observed. In all three cases, a similar particulate–cocontinuous morphology formed for the reference blend, but the rubber inclusions were always smaller than those of the TPE nanocomposite. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of trans-polyoctylene rubber (TOR) on the properties of NR/EPDM blends

trans-Polyoctylene rubber (TOR) was melt blended with an incompatible NR/EPDM (70/30) blend. Mixing torque and temperature were reduced as TOR was added to NR/EPDM blend. The curing characteristics of the blend were affected as TOR participated in vulcanization and became a part of network. A scanning electron micrograph demonstrated that addition of TOR improved the compatibility of the blend and thereby led to a finer phase morphology. The ozone resistance of the blends was determined in terms of a critical stress–strain parameter. The critical stored energy density for ozone cracking was significantly enhanced for the TOR containing rubber blend. It was believed that the improvement in ozone resistance arised from finely dispersed ozone-resistant EPDM particles in the blend. TOR caused an improvement in dynamic properties and an increase in tensile modulus, but a decrease in tensile stress and elongation at break of the rubber blend. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 73: 749–756, 1999     

Blends of polypropylene with poly(cis‐butadiene) rubber. III. Study on the phase structure and morphology of incompatible blends of polypropylene with poly(cis‐butadiene) rubber

Scanning electron microscopy (SEM) was used to study the structure and morphology of partly compatible binary blends of polypropylene with poly(cis‐butadiene) rubber. The SEM images were transformed by digital image process software designed by our group, and binarized images were obtained. The size (mean diameters d_p and characteristic lengths L) of phases was calculated using binarized images. Small‐angle light scattering was employed to study the structure and morphology of phases in the blends. The structural parameters, including correlation distance a_c, average chord lengths l , and mean diameter D_S to describe the structure and morphology of phases in binary blends, were calculated based on the corresponding theory. The variation of correlation distance a_c, average chord length l , and mean diameter D_S were the same as that of mean diameters d_p and characteristic length L. At the same time, the distribution of sizes of the dispersed phase in binary blends was calculated with graph transition technique, which possessed log‐normal distribution characterization. The power spectrum images corresponding to small‐angle light scattering images were obtained by two‐dimensional fourier transformation of binary images. The correlation distances a_cf and average chord length l _f have been calculated by intensity of power spectrum images and that was the same as a_c and l . © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4900–4909, 2006     

Dielectric and mechanical properties of polystyrene/acrylonitrile–butadiene rubber blends

The dielectric and mechanical properties of polystyrene(PS)/acrylonitrile–butadiene rubber (NBR) blends were studied with the aim of improving the insulation properties of NBR. Compatibility investigations, performed with viscosity and dielectric methods and confirmed with the calculated heat of mixing, indicated that such blends were incompatible. To overcome the problem of phase separation between NBR and PS, we chose epoxidized soya bean oil to act as a compatibilizer and added 3% to the blends under investigation. This led to the conclusion that a sample containing 10% PS (either pure or scrap) possessed the most suitable electrical and mechanical properties. For this reason, the sample was chosen for studying the effect of the addition of three types of fillers (quartz, talc, and calcium carbonate) in increasing quantities (up to 80 phr) on the dielectric and mechanical properties. The variation of the dielectric properties with temperature (20–60°C) was also investigated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 540–552, 2002     

Dynamic mechanical properties of polycarbonate and acrylonitrile–butadiene–styrene copolymer blends

Blends of polycarbonate (PC) and poly(acrylonitrile‐co‐butadiene‐co‐styrene) (ABS) with different compositions are characterized by means of dynamic mechanical measurements. The samples show phase separation. The shift in the temperatures of the main dynamic mechanical relaxation shown by the blend with respect to those of the pure components is attributed to the migration of oligomers present in the ABS toward the PC in the melt blending process. A comparison with other techniques (dielectric and calorimetric analysis) and the application of the Takayanagi three block model confirm this hypothesis. In all the studied blend compositions (ABS weight up to 28.6%) the PC appears as the matrix where a disperse phase of ABS is present. The scanning and transmission electron microscopy micrographs show that the size of the ABS particles increases when the proportion of ABS in the blend increases. The FTIR results indicate that the interaction between both components are nonpolar in nature and can be enhanced by the preparation procedure. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1507–1516, 2002     

Mechanical properties,thermal stability,gas permeability,and phase morphology in natural rubber/bromobutyl rubber blends

This work was performed to relate the morphological features and all important properties of the natural rubber (NR) and bromobutyl rubber (BIIR) blends containing hybrid fillers. The BIIR content was varied from 0 to 100 wt%. It is found that tensile and tear strength, hardness as well as resilience of blends tend to decrease with increasing BIIR loading. Regarding the blend morphology, phase inversion is observed when BIIR loading is >50 wt % where BIIR becomes a continuous phase. This result coincides with the marked improvement of thermal stability of the blends determined using thermogravimetric analysis and heat ageing method. Interestingly, that, the gas permeability of blends markedly reduces with an increase in BIIR loading up to 40 wt % when the relatively large elongated particles of BIIR dispersed phase is formed. The results indicate that the relatively large connected structure of the dispersed BIIR can act effectively as a gas barrier. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology and dynamic mechanical properties of natural rubber/nitrile rubber blends containing trans‐polyoctylene rubber as a compatibilizer

The use of trans‐polyoctylene rubber (TOR) as a compatibilizer for blends of natural rubber (NR) and acrylonitrile‐butadiene rubber (NBR) was investigated using atomic force microscopy (AFM) and dynamic mechanical analysis (DMA). The NR/NBR blends containing varying proportions of TOR were prepared in an internal mixer. AFM micrographs of NR/NBR blend at 50/50 (w/w) composition showed heterogeneous phase morphology with NR as a matrix and NBR as a dispersed phase. Inclusion of TOR in the NR/NBR blend altered the phase morphology by reducing the size of the NBR phase. DMA of NR/NBR/TOR showed reduction in tan δ peak height of NBR and an increase in storage modulus E′ in the rubbery region for the NR/NBR blends. A comparison of the E′ obtained from experimental data with that from theoretical models was made to deduce the location of TOR in the blend. Based on the fittings of calculated and experimental values of E′, it was inferred that TOR was incorporated into the NR phase at lower proportion as well as at the interfacial region at higher proportion. The Cole–Cole plot illustrated the compatibilizing effect of TOR. Copyright © 2004 Society of Chemical Industry     

Influences of the phenolic curative content and blend proportions on the properties of dynamically vulcanized natural rubber/acrylonitrile–butadiene–styrene blends

The vulcanization of natural rubber (NR)‐blended acrylonitrile–butadiene–styrene (ABS) was carried out with a phenolic curing agent by a melt‐mixing process. The NR compound was first prepared before blending with ABS. The effects of the phenolic curative contents (10, 15, and 20 phr) and blend proportions (NR/ABS ratio = 50 : 50, 60 : 40, and 70 : 30) on the mechanical, dynamic, thermal, and morphological properties of the vulcanized NR/ABS blends were investigated. The tensile strength and hardness of the blends increased with increasing ABS content, whereas the elongation at break decreased. The strength property resulting from the thermoplastic component and the vulcanized NR was an essential component for improving the elasticity of the blends. These blends showed a greater elastic response than the neat ABS. The thermal stability of the blends increased with increasing ABS component. Scanning electron micrographs of the blends showed a two‐phase morphology system. The vulcanized 60 : 40 NR/ABS blend with 15‐phr phenolic resin showed a uniform styrene‐co‐acrylonitrile phase dispersed in the vulcanized NR phase; it provided better dispersion between the NR and ABS phases, and this resulted in superior elastic properties. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42520.