Effect of rare earth elements surface treatment on tensile properties of aramid fiber‐reinforced epoxy composites

Solutions of rare earth modifier (RES) and epoxy chloropropane (ECP) grafting modification method were used for the surface treatment of aramid fiber. Tensile properties of both the aramid/epoxy composites and single fibers were tested. The effects of RES concentration on tensile properties of aramid/epoxy composites were investigated in detail to explore an optimum amount of rare earth elements in solution for modifying aramid fiber. The fracture surface morphologies of tensile specimens were observed and analyzed with the aid of SEM. The experimental results show that rare earth treatment is superior to ECP grafting treatment in promoting interfacial adhesion between the aramid fiber and epoxy matrix. Meanwhile, the tensile strengths of single fibers were almost not affected by RES treatment. The optimum performance is obtained when the content of rare earth elements is 0.5 wt %. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1037–1041, 2004     

Effect of thermal shock on interlaminar strength of thermally aged glass fiber‐reinforced epoxy composites

Glass fiber/epoxy composites were thermally conditioned at 50, 100, 150, 200, and 250°C for different periods of time and then immediately quenched directly in ice‐cold water from each stage of conditioning temperature. The polymerization or depolymerization by thermal conditioning and the debonding effect by concurrently following thermal shock in polymer composites are assessed in the present study. The short‐beam shear tests were performed at room temperature on the quenched samples to evaluate the value of interlaminar shear strength of the composites. The short conditioning time followed by thermal shock resulted in reduction of shear strength of the composites. The strength started regaining its original value with longer conditioning time. Conditioning at 250°C and thereafter quenching yielded a sharp and continuous fall in the shear strength. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 2062–2066, 2006     

Effect of structure on mechanical properties of vinyl ester resins and their glass fiber‐reinforced composites

The article describes the effect of structure of vinyl ester resins (VE) on the mechanical properties of neat sheets as well as glass fabric‐reinforced composites. Different samples of VE were prepared by reacting ester of hexahydrophthalic anhydride (ER) and methacrylic acid (MAA) (1 : 1 molar ratio) followed by reaction of monomethacrylate terminated epoxy resin with glutaric (E) or adipic (F) or sebacic acid (G) (2 : 1 molar ratio). The neat VE were diluted with styrene and sheets were fabricated by using a glass mold. A significant reduction in the mechanical properties was observed by increasing the methylene content of resin backbone (i.e., sample E to G). Glass fabric‐reinforced composites were fabricated by vacuum assisted resin transfer molding (VARTM) technique. Resin content in the laminates was 50 ± 5 wt %. Increase in the number of methylene groups in the vinyl ester resin (i.e., increasing the bridge length) did not show any significant effect on limiting oxygen index (LOI) value (21 ± 1) of the laminates but tensile strength, tensile modulus, flexural strength, and flexural modulus all increased though these values are significantly lower than observed in laminates based on resin B. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Simplification and application of single fiber fragmentation test on silylated polyester–glass fiber composites

Single fiber fragmentation test (SFFT) was used to investigate the interfacial adhesion in glass fiber‐unsaturated polyester composites. A simplified approach was developed for SFFT based on determination of the maximum number of fragments on the fiber at the end of the test. This approach does not involve length measurements and shortens the experiment time to a few minutes. By using a digital camera attached to the microscope, photographs of the coupon were taken during the test, and the number of fragments within the gauge length were counted later. This method allows quick, quantitative comparison of different fibers and matrices. The test samples were prepared by using commercial polyester resin and E‐glass fibers having different commercial sizings. SFFT results were in excellent agreement with the macromechanical test done on samples prepared with the same glass fiber and same polyester. The crack modes and debonding phenomena were examined from the microscopic images. Atomic force microscopic (AFM) images of the fiber were examined to get detailed topographic information about fiber surfaces. To improve interfacial adhesion, commercial unsaturated polyester was reacted with 3‐aminopropyltriethoxy silane via Michael Addition reaction on the maleate double bonds of the polyester. The resulting silylated polyester was characterized by H¹ NMR spectroscopy. The results of SFFT showed that the maximum numbers of fragments increased 23% on using silylated polyester. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Tribological and mechanical properties of carbon‐nanofiber‐filled polytetrafluoroethylene composites

The effects of various filler concentrations (0.1, 0.5, 1, 1.5, 2, 2.5, and 3 wt %) on the tribological and mechanical properties of carbon‐nanofiber (CNF)‐filled polytetrafluoroethylene (PTFE) composites were studied. Moreover, the influence of various loads (50, 100, 150, and 200 N) and sliding velocities (0.692 and 1.39 m/s) on the friction and wear behaviors of the PTFE composites was investigated. The results showed that the friction coefficients of the PTFE composites decreased initially up to a 0.5 wt % filler concentration and then increased, whereas the antiwear properties of the PTFE composites increased by 1–2 orders of magnitude in comparison with those of pure PTFE. The composite with a 2 wt % filler concentration had the best antiwear properties under all friction conditions. The friction coefficients of the CNF/PTFE composites decreased with increases in the load and sliding velocity, whereas the wear volume loss of the PTFE composites increased. At the same time, the results also indicated that the mechanical properties of the PTFE composites increased first up to a 1 wt % filler concentration and then decreased as the filler concentration was increased above 1 wt %. In comparison with pure PTFE, the impact strength, tensile strength, and elongation to break of the PTFE composites increased by 40, 20, and 70%, respectively, at a 1 wt % filler concentration. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2430–2437, 2007     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Influence of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites

The incorporation of natural fibers with polymer matrix composites (PMCs) has increasing applications in many fields of engineering due to the growing concerns regarding the environmental impact and energy crisis. The objective of this work is to examine the effect of fiber orientation and fiber content on properties of sisal‐jute‐glass fiber‐reinforced polyester composites. In this experimental study, sisal‐jute‐glass fiber‐reinforced polyester composites are prepared with fiber orientations of 0° and 90° and fiber volume of sisal‐jute‐glass fibers are in the ratio of 40:0:60, 0:40:60, and 20:20:60 respectively, and the experiments were conducted. The results indicated that the hybrid composites had shown better performance and the fiber orientation and fiber content play major role in strength and water absorption properties. The morphological properties, internal structure, cracks, and fiber pull out of the fractured specimen during testing are also investigated by using scanning electron microscopy (SEM) analysis. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42968.     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Effect of layering pattern on dynamic mechanical properties of randomly oriented short banana/sisal hybrid fiber–reinforced polyester composites

Dynamic mechanical test methods have been widely employed for investigating the structures and viscoelastic behavior of polymeric materials to determine their relevant stiffness and damping characteristics for various applications. Randomly oriented short banana/sisal hybrid fiber–reinforced polyester composites were prepared by keeping the volume ratio of banana and sisal 1 : 1 and the total fiber loading 0.40 volume fraction. Bilayer (banana/sisal), trilayer (banana/sisal/banana and sisal/banana/sisal), and intimate mix composites were prepared. The effect of layering pattern on storage modulus (E′), damping behavior (tan δ), and loss modulus (E″) was studied as a function of temperature and frequency. Bilayer composite showed high damping property while intimately mixed and banana/sisal/banana composites showed increased stiffness compared to the other pattern. The Arrhenius relationship has been used to calculate the activation energy of the glass transition of the composites. The activation energy of the intimately mixed composite was found to be the highest. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2168–2174, 2005     

Short sisal fiber‐reinforced tire rubber composites: Dynamic and mechanical properties

The world tendency toward using recycled materials demands new products from vegetable resources and waste polymers. In this work, composites made from powdered tire rubber (average particle size: 320 μm) and sisal fiber were prepared by hot‐press molding and investigated by means of dynamic mechanical thermal analysis and tensile properties. The effects of fiber length and content, chemical treatments, and temperature on dynamic mechanical and tensile properties of such composites were studied. The results showed that mercerization/acetylation treatment of the fibers improves composite performance. Under the conditions investigated the optimum fiber length obtained for the tire rubber matrix was 10 mm. Storage and loss moduli both increased with increasing fiber content. The results of this study are encouraging, demonstrating that the use of tire rubber and sisal fiber in composites offers promising potential for nonstructural applications. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 670–677, 2004     

New approach to fabricate densificated continuous fiber reinforced polytetrafluoroethylene composites with significantly improved interfacial bonding and mechanical properties

An unique two‐step technique to fabricate densified continuous fiber reinforced polytetrafluoroethylene (PTFE) composites with significantly improved interfacial bonding and mechanical properties have been successfully developed. The technique is conventional sintering followed by resin film infusion (RFI). The mechanical properties of the composites were studied, and results show that the composites have significantly improved interfacial bonding and mechanical properties. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3588–3591, 2007     

Carbon fiber‐reinforced gelatin composites. I. Preparation and mechanical properties

Composites were made from carbon fibers and gelatin using a solvent‐casting or solution‐impregnation technique. Relationships between the fiber volume fraction (Vf), glycerol (plasticizer) content, gelatin content, fiber form, and mechanical properties (tensile strength and modulus, elongation at break, and shear strength) of the composites were investigated. In long carbon fiber gelatin composite (C_L/Gel), tensile strength, modulus, and shear strength increased steadily with the Vf. In the case of a short carbon fiber gelatin composite (C_S/Gel), an initial improvement in tensile strength and modulus was followed by a reduction, whereas the shear strength improved with the Vf and then reached a constant value. The elongation decreased with the Vf for both composites. It is shown that C_L/Gel had higher values of strength, modulus, and elongation than did C_S/Gel at any Vf level. The effects of glycerol and gelatin contents on the mechanical properties of the composites were found to be much less significant as compared to the Vf. According to scanning electron microscopic observation of the fracture surfaces, the fibers were uniformly distributed in the gelatin matrix, but the interfacial adhesion between the gelatin matrix and the carbon fibers was not very good for both composites. Fiber surface modification would be necessary to further improve the mechanical properties of the two composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 987–993, 2000     

Influence of fiber modification on interfacial adhesion and mechanical properties of pineapple leaf fiber‐epoxy composites

Three kinds of surface treatment, that is, the alkalization (5% w/v NaOH aqueous solution), the deposition of diglycidyl ether of bisphenol A (DGEBA) from toluene solution (1% w/v DGEBA), and the alkalization combined with the deposition of DGEBA (5% w/v NaOH/1% w/v DGEBA) were applied to modify interfacial bonding and to enhance mechanical properties of pineapple leaf fiber (PALF) reinforced epoxy composites. The fiber strength and strain were measured by single fiber test and the fiber strength variation was assessed using Weibull modulus. Furthermore, a fragmentation test was used to quantify the interfacial adhesion of PALF‐epoxy composite. It was verified that the interfacial shear strength of modified PALFs was substantially higher than that of untreated PALF by almost 2–2.7 times because of the greater interaction between the PALFs and epoxy resin matrix. The strongest interfacial adhesion was obtained from the fibers that had been received the alkalization combined with DGEBA deposition. Moreover, the flexural and impact properties of unidirectional PALF‐epoxy composites were greatly enhanced when reinforced with the modified PALFs due to an improvement in interfacial adhesion, particularly in the synergetic use of 5% NaOH and 5% NaOH/1% DGEBA. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of filler surface treatment on mechanical properties and thermal properties of single and hybrid filler–filled PP composites

The influence of two types of surface treatments (aminosilane and Lica‐12) on the mechanical and thermal properties of polypropylene (PP) filled with single and hybrid filler (silica and mica) was studied. An improvement in tensile properties and impact strength was found for both treatments compared to those of untreated composites. However, the filler with silane coupling agent showed better improvement compared to the filler with Lica‐12 coupling agent. This was due to better adhesion between filler and matrix. Thermal analysis indicates that surface treatments increased the nucleating ability of filler, but decreased the coefficient of thermal expansion of PP composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effect of fiber surface modification on the mechanical properties of sisal fiber‐reinforced benzoxazine/epoxy composites based on aliphatic diamine benzoxazine

Sisal fibers were incorporated into a mixture of benzoxazine and bisphenol A type epoxy resins to form a unidirectionally reinforced composite. Surface modifications of the sisal fibers were carried out with sodium hydroxide, γ‐aminopropyltrimethoxysilane, and γ‐glycidoxypropyltrimethoxysilane. The surface treatments led to changes in the morphology, chemical groups, and hydrophilicity of the fibers. The effect of the fiber surface treatments on the fiber–matrix interfacial adhesion and mechanical properties of the composites were also studied. The results showed that surface treatments with sodium hydroxide and a silane coupling agent led to improved fiber–matrix adhesion; this could be seen in the scanning electron micrographs of the fractured surfaces from mechanical testing and the reduction in the impact strength of the composites made from treated fibers. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Mechanical and physical characteristics of cellulose‐fiber‐filled polyacetal composites

We investigated the mechanical and physical characteristics of composites composed of polyacetal [alternatively called polyoxymethylene (POM)] and cellulose fiber (CelF) derived from wood pulp [10–52 wt % (9.3–50.1 vol %)] without any fiber surface treatment. The modulus, deflection temperature under load, and thermal conduction coefficient of the POM/CelF composites were effectively enhanced with increasing CelF content, and the composites had an advantage of specific modulus compared to glass fiber (GF)‐filled POM. The flexural modulus of POM/CelF 40 wt % (38.2 vol %) was measured to be about 6 GPa, which was comparable to that of POM/GF 20 wt % (12.1 vol %). In the composites, the CelFs were distributed randomly as monofilaments, and the debonding of the interface between the fibers and POM matrices in the fracture faces was confirmed as less by scanning electron microscopy observation. The POM/CelF composites possessed lower specific wear rates than the POM/GF composites, and they had damping behaviors near that of neat POM. No clear dependence of the melt flow index of the base POM on these characteristics was observed, except on Charpy impact strength. The composites studied here were unique in their performance and ability to be designed in accordance with specific demands, and they could be potential replacements for mineral‐filled and GF‐filled POM composites. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of hollow glass beads on density and mechanical properties of silicone rubber composites

In this work, low density hollow glass beads (HGB)/silicon rubber (SR) composites were prepared by solution method and flocculation process. The prepared samples were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, tensile test, and friction test. The results show that the densities of SR composites decrease from 1.140 to 0.792 g/cm³ with the addition of HGB. By comparing theoretical density with true density, it can be estimated that the ratio of shattered HGB increase from 8.79% to 24.76%. Especially, the mechanical properties of SR composites were improved by surface modification of HGB. By adding surface-modified HGB at 5 and 10 wt%, the tensile strengths of SR composites were enhanced by 17.8% and 28.2%, respectively. In addition, tear strength, shore A hardness, compression set, and friction property were significantly ameliorated. Furthermore, the mechanism of surface-modified HGB in mechanical properties was analyzed.     

Effect of the delignification of wood fibers on the mechanical properties of wood fiber–polypropylene composites

The effect of the delignification of hornbeam fibers on the mechanical properties of wood fiber–polypropylene (PP) composites was studied. Original fibers and delignified fibers at three levels of delignification were mixed with PP at a weight ratio of 40:60 in an internal mixer. Maleic anhydride (0.5 wt %) as the coupling agent and dicumyl peroxide (0.1 wt %) as the initiator were applied. The produced composites were then hot‐pressed, and specimens for physical and mechanical testing were prepared. The results of the properties of the composite materials indicate that delignified fibers showed better performance in the enhancement of tensile strength and tensile modulus, whereas the hardness of the composites was unaffected by delignification. Delignified fibers also exhibited better water absorption resistance. Notched impact strength was higher for delignified fiber composites, but it was reduced at higher delignification levels. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4759–4763, 2006     

Preparation and mechanical properties of high‐performance short ramie fiber‐reinforced polypropylene composites

Short ramie fiber (RF) was used to reinforce the polypropylene (PP). The composites were prepared in a twin‐screw extruder followed by injection molding. The experimental results showed that both the strength and the modulus of the composites increase considerably with increasing RF content. The tensile strength and flexural strength are as high as 67 and 80 MPa by the incorporation of ramie up to 30 wt %. To the best of our knowledge, this is one of the best results for short natural fiber‐reinforced PP composites. However, the preparation method in this study is more simple and economic. This short RF‐reinforced PP composites extend the application field for short‐nature fiber‐reinforced PP composites. Morphological analysis revealed that it is the high aspect ratio of the fiber and good interfacial compatibility that result in the high performance of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Mechanical properties and viscoelastic behavior of basalt fiber‐reinforced polypropylene

In the present article, a series of commercial‐grade polypropylenes (PP) filled with different contents of short basalt fibers were studied. This composite material presented deterioration of both mechanical characteristics, for example, stress and strain at yield with increasing of the fiber content. On the other hand, the impact strength was fourfold higher than that of unfilled PP. A poor adhesion between the PP matrix and the basalt fibers was detected. This is why interfacial interactions were promoted by the adding of poly(propylene‐g‐maleic anhydride) (PP‐g‐MA). It was observed that the tensile properties of the obtained materials and their impact strengths increased significantly with increasing of the amount of PP‐g‐MA in the blend. The adhesion improvement was confirmed by scanning electron microscopy as well. Fourier transform infrared spectroscopy was applied to assess if any chemical interactions in the system PP/PP‐g‐MA/basalt fibers exist. Dynamic mechanical thermal analysis data showed an increase of the storage modulus with increasing fiber content. The conclusion was made that the modification of the PP matrix led to a higher stiffness but its value remained constant, irrespective of the PP‐g‐MA content. With increasing fiber content, damping in the β‐region decreased, but increase of the coupling agent content restored its value back to that of PP. The loss modulus spectra presented a strong influence of fiber content on the α‐relaxation process of PP. The position of the peaks of the above‐mentioned relaxation processes are discussed as well. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 523–531, 1999