A 3.3-V CMOS 10.7-MHz sixth-order bandpass ΣΔ modulatorwith 74-dB dynamic range

A 3.3-V bandpass ΣΔ modulator for IF sampling at 10.7 MHz in digital radio applications has been developed. The modulator presents a sixth-order single-loop architecture and features a 74-dB dynamic range in a 2OO-kHz signal bandwidth (FM signal), while for a 9-kHz signal bandwidth (AM signal) the dynamic range is 88 dB. The modulator has been integrated in a standard 0.35-μm CMOS technology using switched-capacitor technique and consumes 76 mW from a single 3.3V supply     

A 1.8-mW CMOS ΣΔ modulator with integrated mixer forA/D conversion of IF signals

In this paper, the design of a continuous-time baseband sigma-delta (ΣΔ) modulator with an integrated mixer for intermediate-frequency (IF) analog-to-digital conversion is presented. This highly linear IF ΣΔ modulator digitizes a GSM channel at intermediate frequencies up to 50 MHz. The sampling rate is not related to the input IF and is 13.0 MHz in this design. Power consumption is 1.8 mW from a 2.5-V supply. Measured dynamic range is 82 dB, and third-order intermodulation distortion is -84 dB for two -6-dBV IF input tones. Two modulators in quadrature configuration provide 200-kHz GSM bandwidth. Active area of a single IF ΣΔ modulator is 0.2 mm² in 0.35-μm CMOS     

An 81-MHz IF receiver in CMOS

An 81-MHz CMOS IF receiver for digital wireless applications is presented. The receiver consists of a continuous-time IF amplifier, a subsampling switched-capacitor gain stage, and a sixth-order bandpass ΣΔ A/D converter. Incorporating 24 dB of programmable gain, the receiver achieves 92 dB of dynamic range in a 200 kHz bandwidth. Due to its IF sampling nature, the reciever is immune to de offset, flicker noise, and errors due to mismatches between I and Q signal paths. By utilizing a pseudo two-path resonator architecture in the bandpass ΣΔ A/D converter, a stable passband center frequency which is immune to capacitor mismatch is achieved. Implemented in 0.8-μm CMOS, this chip uses a single 3 V supply and consumes 14.4 mW of power     

A two-path bandpass ΣΔ modulator for digital IFextraction at 20 MHz

Oversampled bandpass A/D converters based on sigma-delta (ΣΔ) modulation can be used to robustly digitize the types of narrowband intermediate frequency (IF) signals that arise in radios and cellular systems. This paper proposes a two-path architecture for a fourth-order, bandpass modulator that is more tolerant of analog circuit limitations at high sampling speeds than conventional implementations based on the use of switched-capacitor biquadratic filters. An experimental prototype employing the two-path topology has been integrated in a 0.6-μm, single-poly, triple-metal CMOS technology with capacitors synthesized from a stacked metal structure. Two interleaved paths clocked at 40 MHz digitize a 200-kHz bandwidth signal centered at 20 MHz with 75 dB of dynamic range while suppressing the undesired mirror image signal by 42 dB. At low input signal levels, the mixing of spurious tones at DC and f_s/2 with the input appears to degrade the performance of the modulator; out-of-band sinusoidal dither is shown to be an effective means of avoiding this degradation. The experimental modulator dissipates 72 mW from a 3.3 V supply     

标准数字工艺下16位精度低压低功耗ΣΔ模数调制器设计

针对输入信号频率在20 Hz～24 kHz范围的音频应用,该文采用标准数字工艺设计了一个1.2 V电源电压16位精度的低压低功耗ΣΔ模数调制器。在6 MHz采样频率下,该调制器信噪比为102.2 dB,整个电路功耗为2.46 mW。该调制器采用一种伪两级交互控制的双输入运算放大器构成各级积分器,在低电源电压情况下实现高摆率高增益要求的同时不会产生更多功耗。另外,采用高线性度、全互补MOS耗尽电容作为采样、积分电容使得整个电路可以采用标准数字工艺实现,从而提高电路的工艺兼容性、降低电路成本。与近期报道的低压低功耗ΣΔ模数调制器相比,该设计具有更高的品质因子FOM。     

A fourth-order bandpass sigma-delta modulator

The modulator of a bandpass analog/digital (A/D) converter, with 63 dB signal/noise for broadcast AM bandwidth signals centered at 455 kHz, has been implemented by modifying a commercial digital-audio sigma-delta (ΣΔ) converter. It is the first reported fully monolithic implementation of bandpass noise shaping and has applications to digital radio     

Quadrature bandpass ΔΣ modulation for digital radio

A quadrature bandpass ΔΣ modulator IC facilitates monolithic digital-radio-receiver design by allowing straightforward “complex A/D conversion” of an image reject mixer's I and Q, outputs. Quadrature bandpass ΔΣ modulators provide superior performance over pairs of real bandpass ΔΣ modulators in the conversion of complex input signals, using complex filtering embedded in ΔΣ loops to efficiently realize asymmetric noise-shaped spectra. The fourth-order prototype IC, clocked at 10 MHz, converts narrowband 3.75-MHz I and Q inputs and attains a dynamic range of 67 dB in 200-kHz (GSM) bandwidth, increasing to 71 and 77 dB in 100- and 30-kHz bandwidths, respectively. Maximum signal-to-noise plus distortion ratio (SNDR) in 200-kHz bandwidth is 62 dB. Power consumption is 130 mW at 5 V. Die size in a 0.8-μm CMOS process is 2.4×1.8 mm²      

A 13.5-mW 185-Msample/s ΔΣ modulator for UMTS/GSMdual-standard IF reception

A system-oriented approach for the design of a UMTS/GSM dual-standard ΔΣ modulator is presented to demonstrate the feasibility of achieving intermediate frequency (IF) around 100 MHz, high dynamic range, and low power consumption at the same time. The circuit prototype implements 78 MHz IF for GSM and 138.24 MHz for wideband code division multiple access (WCDMA), which are set to be 3/4 of the analog-to-digital converter sampling rate. A two-path IF sampling and mixing topology with a low-pass ΔΣ modulator, run at half the sampling rate, is used. Implemented in 0.25-μm CMOS, the circuit achieves dynamic range and peak signal-to-noise and distortion ratio for GSM of 86 and 72 dB, respectively. The corresponding values for WCDMA are 54 and 52 dB, respectively. Optimization is performed at all stages of design to minimize power consumption. The complete circuit consumes less than 11.5 mW for GSM and 13.5 mW for WCDMA at 2.5-V supply, of which 8 mW is due to the analog part     

80-MHz bandpass /spl Delta//spl Sigma/ modulators for multimode digital IF receivers

Three fully differential bandpass (BP) /spl Delta//spl Sigma/ modulators are presented. Two double-delay resonators are implemented using only one operational amplifier. The prototype circuits operate at a sampling frequency of 80 MHz. The BP /spl Delta//spl Sigma/ modulators can be used in an intermediate-frequency (IF) receiver to combine frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an IF of 60 MHz to a digital IF of 20 MHz. The measured peak signal-to-noise-plus-distortion ratios are 78 dB for 270 kHz (GSM), 75 dB for 1.25 MHz (IS-95), 69 dB for 1.762 MHz (DECT), and 48 dB for 3.84 MHz (WCDMA/CDMA2000) bandwidths. The circuits are implemented with a 0.35-/spl mu/m CMOS technology and consume 24-38 mW from a 3.0-V supply, depending on the architecture.     

A CMOS 0.8-μm transistor-only 1.63-MHz switched-current bandpassΣΔ modulator for AM signal A/D conversion

This paper presents a CMOS 0.8-μm switched-current (SI) fourth-order bandpass ΣΔ modulator (BP-ΣΔM) IC capable of handling signals up to 1.63 MHz with 105-bit resolution and 60-mW power consumption from a 5-V supply voltage. This modulator Is intended for direct A/D conversion of narrow-band signals within the commercial AM band, from 530 kHz to 1.6 MHz. Its architecture is obtained by applying a low-pass-to-bandpass transformation (z^-1 →-z^-2) to a 1-bit second-order low-pass ΣΔ modulator (LP-ΣΔM). The design of basic building blocks is based upon a detailed analysis of the influence of SI errors on the modulator performance, followed by design optimization. Memory-cell errors have been identified as the dominant ones. In order to attenuate these errors, fully differential regulated-folded cascode memory cells are employed. Measurements show a best SNR peak of 65 dB for signals of 10-kHz bandwidth and an intermediate frequency (IF) of 1.63 MHz. A correct noise-shaping filtering is achieved with a sampling frequency of up to 16 MHz     

An IF-to-Baseband Σ∆ Modulator for AM/FM/IBOC Radio Receivers With a 118 dB Dynamic Range

A single-bit fifth-order complex continuous-time IF-to-baseband SigmaDelta modulator for AM/FM/IBOC receivers is presented. The input IF is 10.7 MHz and the sampling frequency is 41.7 MHz. The modulator achieves a dynamic range of 118dB in AM mode (3 kHz BW), 98dB in FM mode (200 kHz BW), and 86dB in IBOC mode (500 kHz BW). The modulator's high dynamic range enables the realization of an AM radio receiver without a VGA and without an AM channel-selection filter, thereby reducing system complexity and cost. The elimination of the VGA also improves the sensitivity and the overall noise figure of the receiver. The modulator's spurious free dynamic range is 88 dB in the bandwidth from 25 to 525 kHz. The IM2 distance is 92 dB, and the IM3 distance is 91 dB. The ADC was fabricated in a one-poly five-metal 0.18-mum CMOS process with an active area of 6.0mm². It consumes 210 mW from a 1.8-V supply     

A 1.8-V ΔΣ modulator interface for an electretmicrophone with on-chip reference

The design of a delta-sigma (ΔΣ) analog-to-digital converter (ADC) for direct voltage readout of an electret microphone is presented. The ADC is integrated on the same chip with a bandgap voltage reference and is designed to be packaged together with an electret microphone. Having a power consumption of 1.7 mW from a supply voltage of 1.8 V, the circuit is well suited for use in mobile applications. The single-loop, single-bit, fourth-order ΔΣ ADC operates at 64 times oversampling for a signal bandwidth of 11 kHz. The measured dynamic range is 80 dB and the peak signal-to-(noise+distortion) ratio is 62 dB. The harmonic distortion is minimized by using an integrator with an instrumentation amplifier-like input which directly integrates the 125-mV peak single-ended voltage generated by the microphone. A combined continuous-time/switched-capacitor design is used to minimize power consumption     

Switched-capacitor bandpass delta-sigma A/D modulation at 10.7 MHz

Two second-order bandpass delta-sigma A/D modulators have been implemented in a 0.8 μ BiCMOS process to demonstrate the feasibility of converting a 10.7 MHz radio IF signal to digital form. The circuits, based on switched-capacitor biquads, demonstrated 57 dB SNR in a 200 kHz bandwidth when clocked at 42.8 MHz, dissipating 60 mW from a 5 V supply. The two modulators use different clocking strategies to allow evaluation of a tradeoff between active and passive sensitivities     

A 2.7-V 11.8-mW baseband ADC with 72-dB dynamic range for GSMapplications

A receive baseband analog-to-digital converter (ADC) for a GSM cellular radio system is presented. Low voltage and low power techniques have been applied across many aspects of the design. The circuit consists of two second-order double-sampled semi-bilinear ΣΔ modulators followed by two 576-tap digital finite-impulse response (FIR) GSM-channel filters with offset calibration. The complete ADC achieves a dynamic range of 72 dB and dissipates 11.8 mW from a 2.7-V supply. The area is 1.6 mm² in a 0.5-μm n-well double-poly triple-metal CMOS process     

A 13.5-b 1.2-V micropower extended counting A/D converter

This work presents a study of the extended counting technique for a 1.2-V micropower voice-band A/D converter. This extended counting technique is a blend of ΣΔ modulation with its high resolution but relatively low speed and algorithmic conversion with its higher speed but lower accuracy. To achieve this, the converter successively operates first as a first-order ΣΔ modulator to convert the most significant bits, and then the same hardware is used as an algorithmic converter to convert the remaining least significant bits. An experimental prototype was designed in 0.8-μm CMOS. With a 1.2-V power supply, it consumes 150 μW of power at a 16-kHz Nyquist sampling frequency. The measured peak S/(N+THD) was 80 dB and the dynamic range 82 dB. The converter core including the controller and all reconstruction logic occupies about 1.3×1 mm² of chip area. This is considerably less than a complete ΣΔ modulation A/D converter where the digital decimation filter would occupy a significant amount of chip area     

A 80-MHz bandpass ΔΣ modulator for a 100-MHz IFreceiver

A fully differential fourth-order bandpass ΔΣ modulator is presented. The circuit is targeted for a 100-MHz GSM/WCDMA-multimode IF-receiver and operates at a sampling frequency of 80 MHz. It combines frequency downconversion with analog-to-digital conversion by directly sampling an input signal from an intermediate frequency of 100 MHz to a digital intermediate frequency of 20 MHz. The modulator is based on a double-delay single-op amp switched-capacitor (SC) resonator structure which is well suited for low supply voltages. Furthermore, the center frequency of the topology is insensitive to different component nonidealities. The measured peak signal-to-noise ratio is 80 and 42 dB for 270 kHz (GSM) and 3.84-MHz (WCDMA) bandwidths, respectively. The circuit is implemented with a 0.35-μm CMOS technology and consumes 56 mW from a 3.0-V supply     

A delta-sigma PLL for 14-b, 50 kSample/s frequency-to-digitalconversion of a 10 MHz FM signal

In many wireless applications, it is necessary to demodulate and digitize frequency or phase modulated signals. Most commonly, this is done using separate frequency discrimination and analog-to-digital (A/D) conversion. In low-cost IC technologies, such as CMOS, precise analog frequented discrimination is not practical, so the A/D conversion is usually performed in quadrature or at a nonzero intermediate frequency (IF) with digital frequency discrimination. While practical, the approach tends to require complicated A/D converters, and accuracy is usually limited by the duality of the A/D conversion. This paper presents an alternative structure, referred to as a delta-sigma frequency-to-digital converter (ΔΣFDC), that simultaneously performs frequency demodulation and digitization. The ΔΣFDC is shown to offer high-precision performance with very low analog complexity. A prototype of the key component of the ΔΣFDC has been fabricated in a 0.6 μm, single-poly, CMOS process. The prototype achieved 50 kSample/s frequency-to-digital conversion of a 10 MHz frequency-modulated signal with a worst case signal-to-noise-and-distortion ratio of 85 dB and a worst case spurious-free dynamic range of 88 dH     

A CMOS analog front-end circuit for an FDM-based ADSL system

A CMOS analog front-end circuit for an FDM-based ADSL system is presented. The circuit contains all analog functions including AGC amplifiers, continuous-time band pass filters, ΣΔ AD/DA converters, and digital decimation and interpolation filters. On-chip automatic tuning of the bandpass filters provides more than 300% center frequency range with 1% frequency accuracy. The higher-order ΣΔ AD/DA converters achieve 12-b data conversion at 1.54 Msamples/s with an oversampling ratio of only 32. The 0.7 μm CMOS circuit measures 65 mm² and consumes 1.9 W from a single 5 V power supply     

Granular quantization noise in a class of delta-sigma modulators

The trend toward digital signal processing in communication systems has resulted in a large demand for fast accurate analog-to-digital (A/D) converters, and advances in VLSI technology have made ΔΣ modulator-based A/D converters attractive solutions. However, rigorous theoretical analyses have only been performed for the simplest ΔΣ modulator architectures. Existing analyses of more complicated ΔΣ modulators usually rely on approximations and computer simulations. In the paper, a rigorous analysis of the granular quantization noise in a general class of ΔΣ modulators is developed. Under the assumption that some input-referred circuit noise or dither is present, the second-order asymptotic statistics of the granular quantization noise sequences are determined and ergodic properties are derived     

Multibit oversampled ΣΔ A/D converters as front end forCD players

A technique is presented for deriving all of the different control signals needed for focusing and radial tracking in a digital servosystem for compact disc (CD) players, as well as the full band data from the disc. Because of the different natures of all those signals, different bandwidth and dynamic range, complex analog anti-aliasing circuits, and several types of A/D (analog-to-digital) converters would normally be required to convert the signals from the analog to digital domain. With the proposed technique it is possible to carry out the conversion of the high-frequency data as well as the low-frequency control signals with only a single type of multibit sigma-delta (ΣΔ) A/D converter in combination with digital signal processing. The use of ΣΔ type A/D conversion also has other advantages such as its suitability for integration in a CMOS VLSI process and the fact that the requirements for the anti-aliasing filters in front of the converters are relaxed due to the oversampling technique