A power decoupling control method for an isolated single‐phase AC‐to‐DC converter based on a high‐frequency cycloconverter

This paper proposes a new power decoupling method for a high‐frequency cycloconverter which converts the single‐phase line‐frequency ac input to the high‐frequency ac output directly. The cycloconverter consists of two half‐bridge inverters, two input filter capacitors, and a series‐resonant circuit. The proposed power decoupling method stores the input power ripple at double the line frequency in the filter capacitors. Therefore, the proposed method achieves a unity power factor in ac input and a constant current amplitude in the high‐frequency output without any additional switching device or energy storage element. This paper theoretically discusses the principle and operating performance of the proposed power decoupling method, and the viability is confirmed by using an experimental isolated ac‐to‐dc converter based on the high‐frequency cycloconverter. As a result, the proposed power decoupling method effectively improved the displacement power factor in the line current to more than 0.99 and reduced the output voltage ripple to 4% without any electrolytic capacitor.     

Step‐up/step‐down DC‐DC converter with near zero input/output current ripples

A novel single switch two diode wide conversion ratio step down/up converter is presented. The proposed converter is derived from the conventional single‐ended primary inductor converter (SEPIC) topology, and it can operate as a capacitor‐diode voltage multiplier, which offers simple structure, reduced electromagnetic interference (EMI), and reduced semiconductor voltage stress. The main advantages of the proposed converter are the continuous input/output current, higher voltage conversion ratio, and near‐zero input and output current ripples compared with the conventional SEPIC converter. The absence of both a transformer and an extreme duty cycle permits the proposed converter to operate at high switching frequencies. Hence, the overall advantages will be: higher efficiency, reduced size and weight, simpler structure and control. The theoretical analysis results obtained with the proposed structure are compared with the conventional SEPIC topology. The performance of the proposed converter is verified through computer simulations and experimental results. Copyright © 2012 John Wiley & Sons, Ltd.     

High‐power‐factor single‐switch AC to DC converter for LED lighting

In this paper, we report a novel single‐switch AC to DC step‐down converter suitable for light emitting diodes. The proposed topology has a buck and a buck–boost converter. The circuit is designed to operate in the discontinuous conduction mode in order to improve the power factor. In this topology, a part of the input power is connected to the load directly. This feature of the proposed topology increases the efficiency of power conversion, improves the input power factor, produces less voltage stress on intermediate stages, and reduces the output voltage in the absence of a step‐down transformer. The theoretical analysis, design procedure, and performance of the proposed converter are verified by simulation and experiment. A 36 V, 60 W prototype has been built to demonstrate the merits of this circuit. © 2017 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A soft‐switching high step‐up DC‐DC converter with a single magnetic component

A soft‐switching high step‐up DC‐DC converter with a single magnetic component is presented in this paper. The proposed converter can provide high voltage gain with a relatively low turn ratio of a transformer. Voltage doubler structure is selected for the output stage. Due to this structure, the voltage gain can be increased, and the voltage stresses of output diodes are clamped as the output voltage. Moreover, the output diode currents are controlled by a leakage inductance of a transformer, and the reverse‐recovery loss of the output diodes is significantly reduced. Two power switches in the proposed converter can operate with soft‐switching due to the reflected secondary current. The voltages across the power switches are confined to the clamping capacitor voltage. Steady‐state analysis, simulation, and experimental results for the proposed converter are presented to validate the feasibility and the performance of the proposed converter. Copyright © 2012 John Wiley & Sons, Ltd.     

A high step‐up half‐bridge DC/DC converter with a special coupled inductor for input current ripple cancelation and extended voltage doubler circuit for power conditioning of fuel cell systems

This paper presents a high step‐up soft switched dc–dc converter having the feature of current ripple cancelation in the input stage that is specialized for power conditioning of fuel cell systems. The converter comprises a special half‐bridge converter and a rectifier stage based upon the voltage‐doubler circuit, in which the coupled‐inductor technology is amalgamated with switched‐capacitor circuit. The input current with no ripple is the principal characteristics of this topology that is achieved by utilizing a small coupled inductor. In addition, the low clamped voltage stress across both power switches and output diodes is another advantage of the proposed converter, which allows employing the metal–oxide–semiconductor field‐effect transistors with minuscule on‐state resistance and diodes with lower forward voltage‐drop, and thereby, the semiconductors' conduction losses diminish considerably. The inherent nature of this topology handles the switching scheme based on the asymmetrical pulse width modulation in order for switches to establish the zero voltage switching, leading to lower switching losses. Besides, because of the absence of the reverse‐recovery phenomenon, all diodes turn off with zero current switching. At last, a 250‐W laboratory prototype with the input voltage 24 V and output voltage 380 V is implemented to verify the especial features of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd. Copyright © 2015 John Wiley & Sons, Ltd.     

A new single‐phase high‐power‐factor converter with buck and buck–boost hybrid operation

In recent years, a wide variety of high‐power‐factor converter schemes have been proposed to solve the harmonic problem. The schemes are based on conventional boost, buck, or buck–boost topology, and their performance, such as output voltage control range in the boost and buck topology or efficiency in the buck–boost topology, is limited. To solve this, the authors propose a single‐phase high‐power‐factor converter with a new topology obtained from a combination of buck and buck–boost topology. The power stage performs the buck and buck–boost operations by a compact single‐stage converter circuit while the simple controller/modulator appropriately controls the alternation of the buck and buck–boost operation and maintains a high‐quality input current during both the buck and buck–boost operations. The proposed scheme results in a high‐performance rectifier with no limitation of output voltage control range and a high efficiency. In this paper, the principle and operation of the proposed converter scheme are described in detail and the theory is confirmed through experimental results obtained from 2‐kW prototype converter. © 2000 Scripta Technica, Electr Eng Jpn, 131(3): 91–100, 2000     

A single‐stage integrated bridgeless AC/DC converter for electrolytic capacitor‐less LED lighting applications

In this paper, a single‐stage integrated bridgeless AC/DC converter is proposed. As compared to its counterpart that is composed of totem‐pole boost power factor correction (PFC) cascade fly‐back DC/DC converter, the studied circuit has less components number while overcoming the limits of the totem‐pole type. Thus, it is suitable to the low‐power LED lighting applications. Furthermore, when both PFC inductors L_b and magmatic inductance L_m of the transformer TR1 operate at discontinuous current mode, the bus voltage v_CB can be used to decouple the ac input and constant dc output power. Thus, the approach of increasing bus voltage ripple is employed to eliminate electrolytic capacitors and obtain long operation lifetime. Additionally, it is able to be compatible with our studied twin‐bus configuration for increasing the overall efficiency. A 50‐W hardware prototype has been designed, fabricated, and tested in the laboratory to verify the proposed converter validity. Copyright © 2014 John Wiley & Sons, Ltd.     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.     

Highly Efficient dc–dc Transformer Based on Multicell Converter Topology for Next Generation dc Distribution System

A multicell dc–dc transformer (DCX) with an efficiency of 98.0% is developed for a next generation dc distribution system. Input series output parallel (ISOP) and input parallel output series (IPOS) connection topologies of highly efficient dc–dc cell converters have been applied to realize DCXs that have arbitrary I/O voltages and a high transfer factor. The behavior of a DCX based on multicell topology using nonregulated dc–dc converters is analyzed, and the voltage stress in each cell converter is discussed quantitatively considering the variation in converter circuit parameters. Further, the availability of the applied topology and the validity of the analysis are confirmed by fabricating a prototype of a 384 V to 12 V 2400 W DCX. The multicell topology contributes to realizing a low‐carbon society pushing the promotion of highly efficient, space‐saving, and low cost dc power supplies with standardized, highly efficient cell converter modules.     

Isolated high voltage‐boosting converter derived from forward converter

A novel isolated high voltage‐boosting converter, derived from the traditional forward converter, is presented in this paper. As compared with the traditional forward converter, the demagnetizing winding of the transformer in the proposed converter is used not only to demagnetize but also to improve the voltage conversion ratio. Therefore, the duty cycle is not limited, and the utilization of the transformer, also called coupled inductor, can be increased also. Furthermore, the proposed converter maintains the advantage of possessing a non‐pulsating output current, leading to a small output voltage ripple. Moreover, by applying one additional voltage‐boosting winding to the transformer, the voltage conversion ratio can be significantly improved. In addition, an active clamp circuit is employed in the proposed converter to reduce the voltage stress of the main switch, caused by the leakage inductance in the transformer, and the switches can achieve zero‐voltage switching. Finally, the analysis of operating principles, choice of the turns, turns ratio, core size, and each wire size of the coupled inductor are described in detail, and the experimental results with a prototype with 12‐V input voltage, 100‐V output voltage, and 100‐W output power are provided to verify the feasibility and effectiveness of the proposed converter. Copyright © 2015 John Wiley & Sons, Ltd.     

A novel three‐phase converter using a three‐phase series chopper

This paper proposes a novel three‐phase converter using a three‐phase series chopper. The proposed circuit is composed of three switching devices, three‐phase diode bridge, input reactors, and LC low‐pass filter. In the conventional circuit, which combines three‐phase diode bridge and boost voltage chopper, to obtain sinusoidal input current the output voltage must be two or three times larger than the maximum input line voltage. However, in the proposed circuit, the input current can be controlled to be sinusoidal also when the output voltage is the same as the maximum input line voltage. This can be achieved because in the proposed circuit the discharging current of the reactors does not flow through the voltage source. The control method of the proposed circuit is as simple as that of the conventional circuit since all three switching devices are simultaneously turned on and off. This paper discusses the theoretical analysis and the design of the proposed circuit. In addition, simulation and experimental results are reported. The proposed circuit has obtained a 93% efficiency, and 99.7% at 1.3kW load as the input power factor. © 2000 Scripta Technica, Electr Eng Jpn, 132(4): 79–88, 2000     

Analysis and design of an active‐clamping zero‐voltage‐switching isolated inverse‐SEPIC converter

This paper presents an active‐clamping zero‐voltage‐switching (ZVS) isolated inverse‐SEPIC converter. The high voltage spikes when turning off the switches are eliminated. The energies stored in the parasitic elements can be recycled to achieve the ZVS of switches. Therefore, the conversion efficiency increases substantially, yet with a reduced circuit cost. Detailed analysis and design of the proposed topology are described. Experimental results are recorded for a prototype converter with a DC input voltage ranging from 130 to 180 V, an output voltage of 12 V and a rated output power of 120 W, operating at a switching frequency of 65 kHz. The average active‐mode efficiency is above 88%. Copyright © 2010 John Wiley & Sons, Ltd.     

Operation analysis of quasi‐resonant,high‐frequency transformer link dc–ac converters applied to phase‐shift PWM control on the secondary side

In recent years, the soft‐switching techniques have attracted attention for their peculiar advantages such as low switching loss, high power density, EMI/RFI noise reduction, and so on. The authors have previously reported on a quasi‐resonant dc–dc converter using new phase‐shift PWM control scheme. By using the proposed control scheme, circulating current is eliminated and ZVS (Zero Voltage Switching) is achieved with small commutating current. As a result, the conduction losses caused by their currents are substantially reduced. In this paper, the authors apply a proposed control scheme to a quasi‐resonant high‐frequency transformer link dc–ac converter. As a result, all switching devises in this dc–ac converter can achieve soft switching with small commutating current irrespective of inverter mode and rectifier mode. Its operating principle and unique features are described as compared with the symmetrical control scheme of dc–ac converter. Operating performance of this dc–ac converter in the steady state is illustrated by means of simulation results. © 1999 Scripta Technica, Electr Eng Jpn, 130(2): 88–98, 2000     

LLC resonant DC–DC converter with series‐connected primary windings of transformer

This paper proposes a zero‐voltage switching (ZVS) LLC resonant step up DC–DC converter with series‐connected primary windings of the transformer. The series resonant inverter in the proposed topology has two power switches (MOSFETs), two resonant capacitors, two resonant inductors, and only one transformer with center‐tapped primary windings. The power switches are connected in the form of a half‐bridge network. Resonant capacitors and inductors along with the primary windings of the transformer form two series resonant circuits. The series resonant circuits are fed alternately by operating the power switches with an interleaved half switching cycle. The secondary winding of transformer is connected to a bridge rectifier circuit to rectify the output voltage. The converter operates within a narrow frequency range below the resonance frequency to achieve ZVS, and its output power is regulated by pulse frequency modulation. The converter has lower conduction and switching losses and therefore higher efficiency. The experimental results of a 500‐W prototype of proposed converter are presented. The results confirm the good operation and performance of the converter. © 2014 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

A common‐source active clamped complex type converter

This paper presents a novel common‐source active clamped complex type converter. This converter is the intermediate isolated bus converter for the distributed power supply system in telecommunications equipment. Using active clamped circuits, the switching loss and switching noise can be reduced by means of the soft switching techniques. By adding an auxiliary winding to the transformer, the proposed converter is a common‐source type having direct connection of sources of the two MOSFET switches. As a result, the pulse transformer becomes unnecessary, and the drive circuit is simplified. In the experiment, at 48 V ratings input voltage, 36 to 72 V worldwide input voltage, and 12 V output voltage, the ZVS operation is performed on the main switch and auxiliary switch, and highest efficiency 92.7% is obtained. © 2009 Wiley Periodicals, Inc. Electr Eng Jpn, 167(2): 64–70, 2009; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20682     

High‐efficiency current‐doubler rectifier with low output current ripple and high step‐down voltage ratio

This paper presents a current‐doubler rectifier with low output current ripple and high step‐down voltage ratio. In the proposed rectifier, two extra inductors are introduced to extend the duty ratio of the switches, which in turn reduces the peak current through the isolation transformer as well as the output current ripple; two extra diodes are used to provide discharge paths for the two extra inductors. To highlight the merits of the proposed rectifier, its performance indexes, such as voltage gain function, secondary winding peak current of the isolation transformer, and output current ripple, are analyzed and compared with the conventional current‐doubler rectifier. In this paper, a zero‐voltage‐switching phase‐shift full‐bridge converter with the proposed rectifier with an input voltage of 400 V, output voltage of 12 V, and full load power of 500 W has been implemented and verified, and experimental results have shown that 90% conversion efficiency could be achieved at full load. © 2013 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

An interleaved high step‐up DC‐DC converter with double boost paths

This paper proposed a novel high step‐up converter with double boost paths. The circuit uses two switches and one double‐path voltage multiplier cell to own the double boost and interleaved effects simultaneously. The voltage gain ratio of the proposed DC‐DC converter can be three times the ratio of the conventional boost converter such that the voltage stress of the switch can be lower. The high step‐up performance is in accordance with only one double‐path voltage multiplier cell. Therefore, the number of diodes and capacitors in the proposed converter can be reduced. Furthermore, the interleaved property of the proposed circuit can reduce the losses in the rectifier diode and capacitor. The prototype circuit with 24‐V input voltage, 250‐V output voltage, and 150‐W output power is experimentally realized to verify the validity and effectiveness of the proposed converter. Copyright © 2014 John Wiley & Sons, Ltd.     

The Proposal of Isolated Single‐Stage AC‐DC Converter

An isolated ac‐dc converter has been used in various applications, such as power supply and as a battery charger for electric vehicle. In conventional converters, a loss in each conversion stage can be reduced by applying a soft switching method. However, a conventional converter has many conversion stages including the rectifier stage, power factor correction, and dc/dc converter stages; thus, it is difficult to reduce the total converter loss and size. In this paper, we propose a novel isolated‐type ac‐dc converter with only one conversion stage; it can realize a zero‐voltage switching operation in all switching devices.     

An active‐clamping zero‐voltage‐switching flyback converter with integrated transformer

This paper proposes an active‐clamping flyback converter using an integrated transformer. The proposed converter is composed of two active‐clamp flyback converters. The presented converter can balance the total load current between secondary sides of two transformers so that the rectifier diode conduction loss is reduced. Also, the main switch of one converter is the auxiliary switch for the other converter, so that only two switches are required and both can achieve zero‐voltage‐switching operation. The two transformers are integrated into one magnetic core; therefore, the volume and copper loss of transformer can be reduced. Detailed analysis and design of this integrated magnetic active‐clamping flyback converter are described. Experimental results are recorded for a prototype converter with an AC input voltage ranging from 85 to 135 V, an output voltage of 24 V and an output current of 5 A, operating at a switching frequency of 100 kHz. Copyright © 2014 John Wiley & Sons, Ltd.     

A new topology for nonisolated multiport zero voltage switching dc‐dc converter

In this paper, a new multiport zero voltage switching dc‐dc converter is proposed. Multiport dc‐dc converters are widely applicable in hybrid energy generating systems to provide substantial power to sensitive loads. The proposed topology can operate in 3 operational modes of boost, buck, and buck‐boost. Moreover, it has zero voltage switching operation for all switches and has the ability to eliminate the input current ripple; also, at low voltage side, the input sources can be extended. In addition, it has the ability of interfacing 3 different voltages only by using 3 switches. In this paper, the proposed topology is analyzed theoretically for all operating modes; besides, the voltage and current equations of all components are calculated. Furthermore, the required soft switching and zero input currents ripple conditions are analyzed. Finally, to demonstrate the accurate performance of the proposed converter, the Power System Computer Aided Design(PSCAD)/Electro Magnetic Transient Design and Control(EMTDC) simulation and experimental results are extracted and presented.