The architecture of hydroxy‐functionalized aPS‐b‐random copolymer‐b‐PE via one‐pot strategy combining living free radical polymerization with coordination polymerization

The copolymerization of styrene with ethylene was promoted by CpTiCl₃/BDGE/Zn/MAO catalyst system combining free radical polymerization with coordination polymerization via sequential monomer addition strategy in one‐pot. The effect of polymerization conditions such as temperature, time, ethylene pressure, and Al/Ti molar ratio on the polymerization performance was investigated. The hydroxy‐functionalized aPS‐b‐random copolymer‐b‐PE triblock copolymer was obtained by solvent extraction and determined by GPC, DSC, WAXD, and ¹³C‐NMR. The DSC result indicated that the aPS‐b‐random copolymer‐b‐PE had a T_g at 87°C and a T_m at 119°C which attributed to the T_g of aPS segment and the T_m of PE segment, respectively. The microstructure of the hydroxy‐functionalized aPS‐b‐random copolymer‐b‐PE was further confirmed by WAXD, ¹³C‐NMR, and ¹H‐NMR analysis; and these results demonstrated that the obtained block copolymer consisted of aPS segment, S‐E random copolymer segment, and crystalline PE segment. The connection polymerization of the hydroxy‐functionalized aPS with random copolymer‐b‐PE was revealed by GPC results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of a random terpolymer of L‐lactide, ϵ‐caprolactone and glycolide

A random terpolymer of L ‐lactide (LL), ?‐caprolactone (CL) and glycolide (G) has been synthesized in bulk at 130 °C using stannous octoate as the coordination–insertion initiator. The terpolymer, poly(LL‐ran‐CL‐ran‐G), has been characterized by a combination of analytical techniques: GPC, ¹H NMR, ¹³C NMR, DSC and TG. Molecular weight characterization by GPC shows a unimodal molecular weight distribution with values of M _n = 1.01 × 10⁵ g mol^?1 and M _w / M _n = 2.17. Compositional and microstructural analysis by ¹H NMR and ¹³C NMR, respectively, reveal a terpolymer composition of LL:CL:G = 74:15:11 (mol%) with a chain microstructure consistent with random monomer sequencing. This latter view is supported by the terpolymer temperature transitions (T_g and T_m) from DSC and the thermal decomposition profile from TG. The results and, in particular, the conclusion that it is a random rather than a statistical terpolymer are discussed in the light of current theories regarding the mechanism of this type of polymerization. © 2001 Society of Chemical Industry     

Cationic UV curing behavior and thermal properties of oxetane‐modified polysiloxane prepared from tetraethyl orthosilicate

The oxetane‐modified polysiloxane (Oxe‐PSiO) was synthesized via the partial hydrolysis/condensation of tetraethyl orthosilicate (TEOS) and then transesterification reaction with 3‐ethyl‐3‐(hydroxymethyl)oxetane (EHO), and characterized by FT‐IR, ¹H NMR, ¹³C NMR, and ²⁹Si NMR spectroscopy. Using the water/TEOS molar ratios of 0.8–1.2, the number‐average molecular weights and polydispersity indices were obtained by GPC to range from 1.013 to 2.716 g mol^?1 and around 2.0, respectively. The viscosity of Oxe‐PSiO prepared from the water/TEOS molar ratio of 1.2 sharply increased to 177,545 cps from 438 cps of that from the molar ratio of 0.8. A series of cationic UV‐curable formulations were prepared by blending the Oxe‐PSiO synthesized with the water/TEOS molar ratio of 1.0 into an commercial oxetane‐based resin, 3,3′‐[oxydi(methylene)]bis(3‐ethyloxetane), in different weight ratios. The photopolymerization kinetics studied by photo‐DSC in the presence of triphenylsulphonium hexafluoroantimonate as a cationic photoinitiator showed that both the maximum photopolymerization rate and final oxetane conversion in the cured film decreased with increasing Oxe‐PSiO loading mainly due to the sharp increase in viscosity. The DMTA and DSC results both indicated the improvement in thermal stability, showing 12 and 13.4°C, respectively, higher T_g for the cured film with 50 wt % Oxe‐PSiO loading compared with the pure polymer. Moreover, the temperatures (T_10% and T_50%) at the weight loss of 10 and 50% and final char yields measured by TGA increased with increasing Oxe‐PSiO content. After adding 50 wt % Oxe‐PSiO, compared with the pure polymer the T_10% increased from 349 to 361°C, while the T_50% increased from 409 to 424°C, and with a char yield increase of 8.2% at 800°C. In addition, its greatly increased crosslinking density due to the formation of silica network resulted in the enhancement in pencil hardness from B of the pure polymer to 2H grade. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Characterization of poly(vinyl pyrrolidone‐co‐isobutylstyryl polyhedral oligomeric silsesquioxane) nanocomposites

Poly(vinyl pyrrolidone‐co‐isobutyl styryl polyhedral oligomeric silsesquioxane)s (PVP–POSS) were synthesized by one‐step polymerization and characterized using FTIR, high‐resolution ¹H‐NMR, solid‐state ¹³C‐NMR, ²⁹Si‐NMR, GPC, and DSC. The POSS content can be controlled by varying the POSS feed ratio. The T_g of the PVP–POSS hybrid is influenced by three main factors: (1) a diluent role of the POSS in reducing the self‐association of the PVP; (2) a strong interaction between the POSS siloxane and the PVP carbonyl, and (3) physical aggregation of nanosized POSS. At a relatively low POSS content, the role as diluent dominates, resulting in a decrease in T_g. At a relatively high POSS content, the last two factors dominate and result in T_g increase of the PVP–POSS hybrid. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2208–2215, 2004     

Analysis of low‐density polyethylene‐g‐poly(vinyl chloride) copolymers formed in poly(vinyl chloride)/low‐density polyethylene melt blends with gel permeation chromatography and solid‐state 13C‐NMR

Gel permeation chromatography (GPC) and solid‐state ¹³C‐NMR techniques were used to analyze the structural changes of poly(vinyl chloride) (PVC) in blends of a low‐density polyethylene (LDPE) and PVC during melt blending. The GPC results showed that the weight‐average molecular weight (M_w) of PVC increased with LDPE content up to 13.0 wt % and then decreased at a LDPE content of 16.7 wt %, whereas the number‐average molecular weight remained unchanged for all of LDPE contents used. The ¹³C‐NMR results suggest that the increase in M_w was associated with the formation of a LDPE‐g‐PVC structure, resulting from a PVC and LDPE macroradical cross‐recombination reaction during melt blending. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3167–3172, 2004     

Preparation,thermo‐optic property and transmission loss of chiral azobenzene polyurethane

A novel chiral azobenzene polyurethane (CAPU) was prepared from chromophore, chiral reagent L (?)‐tartaric acid and toluene diisocyanate (TDI). The chemical structure and the thermal property were characterized by UV‐Vis spectrum, FT‐IR, ¹H NMR, circular dichroism (CD) spectrum, differential scanning calorimeter (DSC) and thermogravimetric analysis (TGA). DSC and TGA experiments showed that the glass transition temperature (T_g) and the decomposition temperature (T_d) at 5% mass loss were 110°C and 199°C, respectively. The refractive index (n) and thermo‐optic coefficient (dn/dT) of the CAPU were measured at 650 nm wavelength and different temperature by attenuated total reflection (ATR) technique. By using CCD digital imaging devices, transmission loss of CAPU was measured and the value is 0.565dB/cm. The results will provide the foundation for many potential applications such as digital thermo‐optic switch materials and other fields in the future. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polar polystyrene‐isoprene‐styrene copolymers with long polybutadiene branches

Polar polystyrene‐isoprene‐styrene (SIS) copolymers having epoxide groups and long polybutadiene (PB) branches were synthesized via the combination of in situ epoxidation, anionic polymerization and graft‐onto reaction. They were characterized with ¹H NMR, GPC, FT‐IR, DSC, and contact angle test. Their polarity was determined by the epoxidation degree and graft efficiency. The epoxidation degree linearly increased with the epoxidation time. The graft efficiency decreased with the branch length, but increased with the epoxidation degrees. Although their glass transition temperature (T_g) of diene blocks and flexibility properties had been negatively affected by in situ epoxidation, they could be modulated by the epoxidation degree, branch length, and branch density. Their T_g could be tailored by the branch length and branch density since they fitted the Fox equation very well, especially as the longer branches were grafted. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40303.     

Poly(vinyl pyrrolidone‐co‐octavinyl polyhedral oligomeric silsesquioxane) hybrid nanocomposites: Preparation,thermal properties,and Tg improvement mechanism

A series of poly(vinyl pyrrolidone‐co‐octavinyl polyhedral oligomeric silsesquioxanes) (PVP‐POSS) organic–inorganic hybrid nanocomposites containing different percentages of POSS were prepared via free radical polymerization and characterized by FTIR, high‐resolution ¹H‐NMR, solid‐state ²⁹Si‐NMR, GPC, DSC, and TGA. POSS contents in these nanocomposites can be effectively controlled by varying the POSS feed ratios which can be accurately quantified by FTIR curve calibration. On the basis of ²⁹Si‐NMR spectra, average numbers of reacted vinyl groups of each octavinyl‐POSS macromer are calculated to be 5–7, which depends on POSS feed ratios. Both GPC and DSC results indicate that these nanocomposites display network structure and the degree of crosslinking increases with the increase of the POSS content. The incorporation of POSS into PVP significantly improves their thermal properties (T_g and T_dec) primarily due to crosslinking structure and dipole–dipole interaction between POSS cores and PVP carbonyl groups. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Structure–property relationship of blocked diisocyanates: synthesis of polyimides using imidazole‐blocked isocyanates

Imidazole, 2‐methylimidazole and benzimidazole‐blocked aromatic and aliphatic diisocyanates have been prepared and polymerized with pyromellitic dianhydride in the presence of a basic catalyst. The polymers are characterized with FTIR, ¹H NMR and ¹³C NMR spectroscopy and GPC, DSC and TGA. The structure–property relationship of blocked diisocyanates are discussed in terms of molecular weight of the polyimides obtained. Considering the blocking agent, GPC results show that the benzimidazole blocked adduct yields higher molecular weight polymer than the 2‐methylimidazole‐blocked adduct which, in turn, yields higher molecular weight polymer than the imidazole‐blocked adduct. Considering the structure of the isocyanate, the molecular weight of polymer increases from isophorone diisocyanate to hexamethylene diisocyanate and to toluene diisocyanate (TDI). DSC traces of the polymers derived from TDI show glass transitions (T_g) in the temperature range 152–180 °C and the values increase from the polymer based on imidazole‐blocked TDI to 2‐methylimidazole‐blocked TDI and to benzimidazole‐blocked TDI. © 2000 Society of Chemical Industry     

Structural investigations of (9‐ethyl‐carbazol‐6‐yl) methyl methacrylate/methyl acrylate copolymers using two‐dimensional NMR spectroscopy

(9‐Ethyl‐carbazol‐6‐yl) methyl methacrylate/methyl acrylate (E/A) copolymers of different compositions were prepared by solution polymerization by varying the molar infeed ratio, using AIBN as initiator at 60°C. The reactivity ratios calculated by Kelen–Tudos (KT) method were found to be r_E = 1.16 ± 0.02 and r_A = 0.69 ± 0.01 whereas those calculated from RREVM method were found to be r_E = 1.18 and r_A = 0.68. The molecular weights (M_w) and polydispersity index (PDI, M_w/M_n) were determined using gel permeation chromatography (GPC). Glass transition temperatures (T_g) for different compositions of E/A copolymers were determined using differential scanning calorimetry (DSC). Copolymer molar outfeed ratio (F_E) was calculated from ¹H NMR spectra. The α‐methyl, methine, backbone methylene, and quaternary carbon resonance signals of the copolymers were distinguished using ¹³C{¹H}, DEPT‐45, ‐90, and ‐135 NMR techniques. The α‐methyl and β‐methylene showed compositional and configurational sensitivity up to pentad and tetrad level, respectively, whereas methine showed only compositional sensitivity up to pentad level. Unambiguous assignments for ¹H and ¹³C{¹H} NMR spectra were done by correlating 1D (¹H, ¹³C{¹H}, DEPT) and 2D (HSQC, TOCSY) NMR data. The spectral assignments for carbonyl region were done by studying higher bond order couplings by heteronuclear multibond correlation (HMBC) spectra. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 5595–5606, 2006     

Thermal analysis of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) irradiated under vacuum

Poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) was irradiated by ⁶⁰Co γ‐rays (doses of 50, 100 and 200 kGy) under vacuum. The thermal analysis of control and irradiated PHBV, under vacuum was carried out by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The tensile properties of control and irradiated PHBV were examined by using an Instron tensile testing machine. In the thermal degradation of control and irradiated PHBV, a one‐step weight loss was observed. The derivative thermogravimetric curves of control and irradiated PHBV confirmed only one weight‐loss step change. The onset degradation temperature (T_o) and the temperature of maximum weight‐loss rate (T_p) of control and irradiated PHBV were in line with the heating rate (°C min^?1). T_o and T_P of PHBV decreased with increasing radiation dose at the same heating rate. The DSC results showed that ⁶⁰Co γ‐radiation significantly affected the thermal properties of PHBV. With increasing radiation dose, the melting temperature (T_m) of PHBV shifted to a lower value, due to the decrease in crystal size. The tensile strength and fracture strain of the irradiated PHBV decreased, hence indicating an increased brittleness. Copyright © 2004 Society of Chemical Industry     

Viscoelasticity and morphology of poly(ethylene‐co‐vinyl acetate)/polyisobutylene blends

Blends of an ethylene/vinyl acetate copolymer (EVA) and polyisobutylene of various compositions were prepared by mechanical mixing at a temperature above the melting point of EVA (T_m^EVA) but below the upper critical solution temperature of 170°C for given blends. The rheological properties of the components and blends were studied in the region of small‐amplitude oscillating deformation at temperatures above and below T_m^EVA in the frequency range of 0.01–100 rad/s. At temperatures lower than T_m^EVA, the rheological properties were determined by the existence of the yield stress. With diminishing frequency, the viscosity increased, and the plateau in the relaxation spectrum at low frequencies broadened. The morphology of the blends depended on the conditions of sample heating. The introduction of a finely dispersed filler into the blends led to an anomalous drop in the viscosity. The morphology of the systems that arose by mechanical blending of the molten components was the important factor in the rheological behavior. The observed effects were examined in the framework of the concept of structural networks formed in melts by nonmelted crystallites of EVA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2700–2707, 2006     

Synthesis,characterization, and curing behavior of carborane‐containing benzoxazine resins with excellent thermal and thermo‐oxidative stability

Two benzoxazine precursors bearing carborane moiety ( 1 and 2 ) were designed and synthesized successfully by the Mannich reaction of corresponding carborane bisphenol ( 3 and 4 ) with aniline and formaldehyde in 1,4‐dioxane. The obtained precursors were characterized by using multiple spectroscopic techniques including GPC, FTIR, ¹H NMR, ¹³C NMR, and ¹¹B NMR. Nonisothermal DSC studies showed that precursor 1 owned lower apparent activation energies (E_a) than 2 . The optimum curing processes of benzoxazine precursors were also obtained on the basis of DSC data. TGA analyses manifested that the incorporation of carborane moiety endowed the obtained benzoxazine resins (cured 1 and 2 ) with excellent thermal stability and unique thermo‐oxidative stability. The T_d data showed that the initial degradation of both cured 1 and 2 under nitrogen and air was postponed to some extent owing to the shielding effect of carborane moiety on adjacent organic fragments. At higher temperature three‐dimensional polymer networks with B‐O‐B and B–C linkages were formed as chars by the reaction of carborane cage with atmospheric moisture, degradation products such as phenolic hydroxyl, and oxygen (under air). Under nitrogen this network hindered the motion of radicals formed at elevated temperature and thus inhibited further polymer degradation processes. While under air, the formed boron‐rich networks could hardly be further oxidized into carbon dioxide so that the carborane‐containing benzoxazine resins also showed very high char yields. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43488.     

The synthesis of high molecular weight polybutene‐1 catalyzed by Cp★ Ti(OBz)3/MAO

A new stereoregular polybutene‐1 was synthesized with a novel catalyst precursor η⁵‐pentamethyl cyclopentadienyl titanium tribenzyloxide (CpTi(OBz)₃) and methylaluminoxane (MAO). The effects of polymerization conditions on the catalytic activity, molecular weight and stereoregularity of the products were investigated in detail. It was found the catalyst exhibited highest activity of 91.2 kgPB mol Ti⁻¹ h⁻¹ at T = 30 °C, Al/Ti = 200. The catalytic activity and molecular weight were sensitive to the Al/Ti (mole/mole), polymerization temperature; they also depended on the Ti concentration. The molecular weight of the products increased with decreasing temperature. The structure and properties of the polybutene‐1 were characterized by ¹³C NMR, GPC, DSC and WAXD. The result showed the microstructure of polybutene‐1 extracted by boiling heptane was stereoregular, whereas the ether‐soluble fraction was atactic. The molecular weight of polybutene‐1 was over one million g mol⁻¹ and its molecular weight distribution ( M _w/ M _n) was from 1.1 to 1.2. © 2001 Society of Chemical Industry     

Synthesis and properties of polystyrene‐b‐poly(ethylene oxide)‐b‐polystyrene triblock copolymers

A series of well‐defined and property‐controlled polystyrene (PS)‐b‐poly(ethylene oxide) (PEO)‐b‐polystyrene (PS) triblock copolymers were synthesized by atom‐transfer radical polymerization, using 2‐bromo‐propionate‐end‐group PEO 2000 as macroinitiatators. The structure of triblock copolymers was confirmed by ¹H‐NMR and GPC. The relationship between some properties and molecular weight of copolymers was studied. It was found that glass‐transition temperature (T_g) of copolymers gradually rose and crystallinity of copolymers regularly dropped when molecular weight of copolymers increased. The copolymers showed to be amphiphilic. Stable emulsions could form in water layer of copolymer–toluene–water system and the emulsifying abilities of copolymers slightly decreased when molecular weight of copolymers increased. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 727–730, 2006     

Synthesis and properties of a novel bismaleimide resin containing 1,3,4‐oxadiazole moiety and the blend systems thereof with epoxy resin

A new bismaleimide monomer, 2‐((4‐maleimidophenoxy)methyl)‐5‐(4‐maleimidophenyl)‐1,3,4‐oxadiazole (Mioxd), was designed and synthesized. The chemical structure of the monomer was confirmed by means of Fourier transform infrared (FTIR) spectroscopy, proton nuclear magnetic resonance (¹H NMR) spectroscopy and elemental analysis, and its thermal properties were characterized using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Mioxd as a reactive modifier was blended with epoxy resin based on bisphenol A diglycidyl ether (DGEBA) in weight ratio of 5, 10, and 15%, using 4,4′‐diaminodiphenyl sulfone (DDS) as hardener. The effect of Mioxd addition on the cure behavior and thermal properties of the blend resins was studied by DSC, TGA, and dynamic mechanical analysis (DMA). DSC investigations showed that the main exothermic peak temperature (T_p) of the blend systems did not obviously shift with increasing Mioxd content whereas a new shoulder appeared and gradually grew on the high temperature side of the exothermic peak. The results of DMA measurements exhibited the glassy storage modulus (G') and glass transition temperatures (T_g) increased as the Mioxd content was increased, the cured blends investigated were miscible and no phase separation occurred. Further, the thermal decomposition temperature first decreased and then increased, but the char yield at 600°C increased with an increase in Mioxd content. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Study on the synthesis,characterization, and kinetic of bulk polymerization of disproportionated rosin (β‐acryloxyl ethyl) ester

Disproportionated rosin ((β‐acryloxyl ethyl) ester (DR‐2‐HEA) was synthesized by esterification of dispoportionated rosin (DR) with 2‐hydroxyethyl acrylate (2‐HEA) and evaluated by FTIR spectroscopy, GC/MS, ¹³C‐NMR spectroscopy. Kinetics parameters of bulk polymerization of DR‐2‐HEA in the presence of initiator AIBN was studied by using DSC. It has been assumed that the process of polymerization obey nth order empirical kinetic model to evaluate the kinetic parameters. The relative molecular weight and glass transition temperature of polymer of DR‐2‐HEA at different temperature was measured by GPC and DSC, respectively. The results showed that the temperature had no significant effect on the enthalpy of polymerization and the velocity of polymerization increased by the increase of temperature. DSC experimental data fit the simulation well while the reacted fraction (α) in the interval of 0.4<α<1. The polymer of DR‐2‐HEA is oligomer. The molecular weight and T_g did not affect by polymerization temperature. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Characterization and thermal‐oxidative degradation behavior of poly(ethylene terephthalate‐co‐4,4′‐bibenzoate) prepared via direct esterification technique

A series of poly(ethylene terephthalate‐co‐4,4′‐bibenzoate)s (PETBBs) were prepared via direct esterification from the monomers of terephthalic acid (TPA), 4,4′‐biphenyl dicarboxylic acid (BPDA), and ethylene glycol (EG) with different molar ratios. The chemical compositions of the obtained PETBBs, investigated by H¹‐NMR, were identical with the feed ratio, and the high molecular weights of PETBBs were confirmed by GPC analysis. The glass transition, crystallization, and melting behavior of them were measured by DSC; the results indicated that, in the range of 5–25 mol% of BPDA addition, the glass transition temperature (T_g) increased almost linearly and the melting temperature (T_m) decreased with increasing content of BPDA unit. As expected, the crystallization of PETBB became difficult with increasing introduction of BPDA, explained by higher crystallization temperature and smaller crystallization enthalpy from the glassy state. This decrease of crystallization rate may be beneficial to film processing. Moreover, owing to the introduction of rigid‐rod BPDA unit, the initial and maximum thermal‐oxidative decomposition temperatures were enhanced. The kinetic analysis of the thermal‐oxidative degradation indicated that the apparent activation energies of degradation for these PETBBs became higher than that of PET. POLYM. ENG. SCI., 2012. © 2012 Society of Plastics Engineers     

Synthesis of hyperbranched polyester‐amides and their application as crosslinkers for polyurethane curing systems

A series of hyperbranched polyester‐amides (S1, S2, S3) with trimethylolpropane as a core molecule were synthesized using core‐dilution/slow monomer addition strategy. The products were characterized by FTIR, ¹³C NMR, GPC, TGA, hydroxyl value measurement, and viscosity measurement. The result showed that the hyperbranched polyester‐amides synthesized had narrow molecular weight distribution and high degree of branching (DB). The hyperbranched polyester‐amides synthesized were used as crosslinkers for polyurethane curing systems and the mechanical properties of the polyurethane curing systems were investigated. It was found that the best tensile property and tear strength were obtained when the S2 were used as crosslinkers and the molar ratio of  OH and  NCO was 1 : 1. It was also found that the polyurethane curing systems had the highest hardness and T_g when the S3 were used as crosslinkers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of the biodegradable copolymers from succinic acid and adipic acid with 1,4-butanediol

Biodegradable homopolyesters such as poly(butylene succinate) (PBSU) and poly(butylene adipate) (PBAD) and copolyesters such as poly(butylene succinate-co-butylene adipate) (PBSA) were synthesized, respectively, from succinic acid (SA) and adipic acid (AA) with 1,4-butanediol through a two-step process of esterification and deglycolization. The polyester compositions and physical properties of both homopolyesters and copolyesters were investigated by ¹H– and ¹³C–NMR, DSC, GPC, WAXD, and optical polarizing microscopy. The melting point (T_m) of these copolyesters decreased gradually as the contents of butylene adipate increased and the glass-transition temperature (T_g) of these copolyesters decreased linearly as the contents of the adipoyl unit increased. PBSA copolyesters showed two types of XRD patterns of PBSU and PBAD homopolyesters. Furthermore, the biodegradation and hydrolytic degradation of the high molecular weight PBSU homopolyester, PBAD homopolyester, and PBSA copolyesters were investigated in the composting soil and NH₄Cl aqueous solutions at a pH level of 10.6. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 2808–2826, 2001