Preparation and properties of Fe(II)‐ion‐sensitive colour‐changing fabric

Textile fabrics were dyed with complexometric indicators (ionochromic dyes) to develop Fe(II) ionochromic fabric. Three kinds of ionochromic dye were used to dye silk fabric, and they were evaluated for colour changes triggered by Fe(II) solution. The K/S values and photos of the fabrics were then recorded. It was found that 1,10‐phenanthroline was the most suitable ionochromic dye in these dyes. Colour change from white to red could be clearly seen when 1,10‐phenanthroline‐dyed silk fabric was triggered by Fe(II) solution, but it showed no colour change when triggered by Cu(II), Mg(II), or Ca(II) solution. Moreover, 1,10‐phenanthroline‐dyed nylon, polyester, and cotton fabrics showed no obvious colour changes after triggering by Fe(II) solution. Ion concentration, pH value, and reaction time could affect the colour changes. When triggered by 8 mg l^?1 of Fe(II) solution at neutral pH for about 15 min, the ionochromic fabric showed a clear colour change. In addition, three coloured fabrics in green, blue, and yellow were also dyed with 1,10‐phenanthroline. It was found that they could also show clear colour changes when triggered by Fe(II) solution. These ionochromic fabrics may find broad application in many fields, such as Fe(II) detection, magic toys, anticounterfeiting materials, and bionic silk flowers.     

A facile synthesis and tautomeric structure of novel 4‐arylhydrazono‐3‐(2‐hydroxyphenyl)‐2‐pyrazolin‐5‐ones and their application as disperse dyes

The main target of this paper was the synthesis of novel azo disperse dyes with better dyeing properties, together with a systematic investigation to determine their dominant tautomer(s) from 12 possible tautomeric structures. In this regard, novel azopyrazolin‐5‐one dyes were synthesised via the reaction of hydrazine hydrate with 2,3,4‐chromantrione‐3‐arylhydrazones. The acid dissociation constants both in the ground and in the excited state for the series prepared were determined and correlated by the Hammett equation. The results of this correlation, together with spectral data, indicated that the compounds under scrutiny exist predominantly in the keto‐hydrazo structure as a Z‐configuration, both in the ground and in the excited state. Finally, the synthesised dyes were applied as disperse dyes for dyeing polyester fabrics, and their fastness properties were evaluated. Also, the position of colour in CIELAB coordinates was estimated and discussed.     

Synthesis of (R)‐ and (S)‐Ricinoleic Acid Amides and Evaluation of Their Antimicrobial Activity

A series of fatty acid amides derived from (R)‐ and (S)‐ricinoleic acid and 4 cyclic and acyclic amines were synthesized in a proecological solvent‐free process with yields ranging from 43 to 88%. All S‐configured compounds and both enantiomers of amide with 2‐amino‐2‐methyl‐1‐propanol were obtained and studied in terms of biological activity for the first time. The evaluation of antimicrobial activity of (R)‐ and (S)‐ricinoleic acid derivatives against 13 different microorganisms representing Gram‐negative and Gram‐positive bacteria, yeast, and molds showed significant inhibitory activity against Gram‐positive bacteria, especially Micrococcus luteus and Bacillus subtilis, and against selected molds. Ethanolamine‐ and pyrrolidine‐derived amides showed the most promising antibacterial and antimold potential. Derivatives from ricinoleic acid and pyrrolidine were the most active against both selected molds, Aspergillus brasiliensis and Penicillium expansum. Moreover, the R‐configured analog was the most potent against B. subtilis. The amides of ricinoleic acid with ethanolamine exhibited significant potential to Staphylococcus aureus, which distinguished them from the rest of tested derivatives to which this bacterium was very resistant.     

Novel hydrolysable azo disperse dyes based on N‐ester‐1,8‐naphthalimide: dyeing of polyester–cotton blends

The dyeing of polyester–cotton blends with new alkali‐hydrolysable azo disperse dyes based on N‐ester‐1,8‐naphthalimide was investigated. Polyester–cotton blend fabrics were dyed using both one‐ and two‐bath methods. Dyes 3 and 4 offered lower colour yield on polyester using the one‐bath method. For the rest of the dyes, employing either the one‐ or two‐bath method resulted in a similar colour yield on polyester fabric. The results for fastness properties and colour yield of the dyeings showed that the dyes were suitable for dyeing polyester–cotton blends using the one‐bath method. The kinetic study of hydrolysis of the dyes in alkali media obeyed the pseudo first‐order reaction rate.     

Antimicrobial properties of bio‐inspired poly(4‐vinyl‐2‐pyridone) and its N‐alkylated cationic derivatives

Developing new antimicrobial polymers and designing new antimicrobial materials are important research areas for overcoming bacterial resistance. In the present study a new polymer, poly(4‐vinyl‐2‐pyridone), having bioactive structure analogous to that of naturally occurring heterocyclic compounds, was synthesized from 4‐vinylpyridine following a simple protocol. To augment the antibacterial properties of the synthesized polymer, N ‐alkylation of the heterocyclic pyridone moieties was achieved with ethylene chlorohydrin (2‐chloroethanol) to generate choline analogous structure. Also, its N ‐butylated analogue was synthesized as a reference compound to study structure–activity relationship. Structures of the polymers were confirmed using various characterization techniques. Antimicrobial efficacy of the polymers was determined using the minimum inhibitory concentration method in parallel experiments. The test microorganisms used were a Gram (+) bacterium (Staphylococcus epidermidis ), Gram (?) bacteria (Salmonella typhi , Pseudomonas aeruginosa and Escherichia coli ) and a fungus (Candida albicans ). Both the polymer derivatives are far more effective antimicrobial agents than the pristine polymer. Trends in the antimicrobial efficacy of these polymers correlate with their zeta potential values. © 2016 Society of Chemical Industry     

Synthesis of temporarily solubilised azo disperse dyes containing a β‐sulphatoethylsulphonyl group and dispersant‐free dyeing of polyethylene terephthalate fabric

Disperse dyes containing a β‐sulphatoethylsulphonyl group have temporary solubility and can be applied for dispersant‐free dyeing of hydrophobic fibre. Six novel temporarily solubilised azo disperse dyes having a β‐sulphatoethylsulphonyl group in their structures were synthesised, and their dyeing properties on polyester were investigated. As a dye intermediate, a diazo component having dibromo groups was prepared, and 4‐diethylamino‐4′‐(2‐sulphatoethylsulphonyl‐4,6‐dibromo)azobenzene dyes were prepared by a diazo‐coupling reaction. Then, the dyes containing dicyano groups were prepared by cyanation of corresponding dyes with dibromo groups. The absorption maxima of the dyes were affected by the substituents in the diazo and coupling component rings and varied from 434 to 616 nm in dimethylformamide. Polyethylene terephthalate woven fabric could be dyed with the synthesised temporarily solubilised dyes without using any dispersants. Dyebath pH affected the K/S value at maximum absorption as well as percentage exhaustion on polyethylene terephthalate fabric, and the optimum pH was 5. The dyes gave brownish orange, red, purple, and greenish blue hues on polyethylene terephthalate fabrics, and colour build‐up was good. Wash fastness was good to excellent, rubbing fastness was moderate to excellent, and light fastness was poor to moderate.     

Synthesis and characterization of tetrakis‐ derivatives of bisphenol‐A with 4‐phenylazoaniline and 5‐(4‐aminophenylazo)‐25,26,27‐tribenzoyloxy‐ 28‐hydroxycalix[4]arene

The synthesis of tetrakis‐ derivatives of bisphenol‐A containing azo groups at their 2,2′,6,6′‐positions is reported. Novel examples of bisphenol‐A, coupled with diazonium salts and derived from 4‐phenylazoaniline and 5‐(4‐aminophenylazo)‐25,26,27‐tribenzoyloxy‐28‐hydroxycalix [4]arene, have been synthesized. It has been observed that the coupling reaction of diazonium salt obtained from 4‐phenylazoaniline with bisphenol‐A gives tetrakis‐ while those derived from 5‐(4‐aminophenylazo)‐25,26,27‐tribenzoyloxy‐28‐hydroxycalix [4]arene give partially substituted bisphenol‐A analogues. The newly prepared tetrakis‐azo substituted bisphenol‐A compounds ( 1 and 2 ) are characterized by using UV‐vis, FT‐IR, ¹H‐NMR spectroscopic methods as well as elemental analysis techniques. These azo compounds give rise to bathochromic shifts in the absorption spectra, which can even be detected by “naked eye.” © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Polyamides obtained by direct polycondesation of 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl] fluoren‐9‐YL]‐2‐methyl‐phenoxy]aniline with dicarboxylic acids based on a diphenyl‐silane moiety

Polyamides (PAs) containing fluorene, oxyether, and diphenyl‐silane moieties in the repeating unit were synthesized in > 85% yield by direct polycondesation between a diamine and four dicarboxylic acids. Alternatively, one PA was synthesized from an acid dichloride. The diamine 4‐[4‐[9‐[4‐(4‐aminophenoxy)‐3‐methyl‐phenyl]fluoren‐9‐yl]‐2‐methyl‐phenoxy]aniline ( 3 ) was obtained from the corresponding dinitro compound, which was synthesized by nucleophilic aromatic halogen displacement from p‐chloronitrobenzene and 9,9‐bis (4‐hydroxy‐3‐methyl‐phenyl)fluorene ( 1 ). Monomers and polymers were characterized by FTIR and ¹H, ¹³C, and ²⁹Si‐NMR spectroscopy and the results were in agreement with the proposed structures. PAs showed inherent viscosity values between 0.14 and 0.43 dL/g, indicative of low molecular weight species, probably of oligomeric nature. The glass transition temperature (T_g) values were observed in the 188–211°C range by DSC analysis. Thermal decomposition temperature (TDT_10%) values were above 400°C due to the presence of the aromatic rings in the diamine. All PAs showed good transparency in the visible region (>88% at 400 nm) due to the incorporation of the fluorene moiety. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of 2‐hydroxyethylmethacrylate/2‐(3‐indol‐yl)ethylmethacrylamide‐based novel hydrogels as drug carrier with in vitro antibacterial properties

In this study, a new cationic monomer 2‐(3‐indol‐yl)ethylmethacrylamide (IEMA) derived from tryptamine was synthesized in a single step and characterized by Fourier transform infrared (FTIR), ¹H‐NMR, and ¹³C‐NMR. Then, one‐step preparation of novel poly[2‐hydroxyethylmethacrylate‐c‐2‐(3‐indol‐yl)ethylmethacrylamide], or p(HEMA‐c‐IEMA), copolymeric hydrogels has been performed successfully with IEMA and 2‐hydroxyethylmethacrylate (HEMA) as monomers using free radical aqueous polymerization. The hydrogels were characterized with scanning electron microscopy, FTIR, elemental analysis, thermogravimetric analysis, and texture profile analysis instruments. p(HEMA‐c‐IEMA) hydrogels were used for swelling, diffusion, drug release, and antibacterial activity studies. The drug‐release behavior of the hydrogels was determined as a function of time at 37 °C in pH 1.2 and 7.2. The swelling and drug‐release studies showed that an increased IEMA amount caused a higher increase in swelling and drug‐release values. Additionally, zero‐order, first‐order, and Higuchi equation kinetic models were applied to the drug‐release data, and the data fit well in the Higuchi model, and the Peppas power‐law model was applied to the release mechanism. Finally, the antibacterial activities of the hydrogels were screened against Gram‐positive bacteria (Bacillus cereus and Staphylococcus aureus) and Gram‐negative bacteria (Escherichia coli and Salmonella typhimurium). © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45550.     

Synthesis of hyperbranched polyester‐amides and their application as crosslinkers for polyurethane curing systems

A series of hyperbranched polyester‐amides (S1, S2, S3) with trimethylolpropane as a core molecule were synthesized using core‐dilution/slow monomer addition strategy. The products were characterized by FTIR, ¹³C NMR, GPC, TGA, hydroxyl value measurement, and viscosity measurement. The result showed that the hyperbranched polyester‐amides synthesized had narrow molecular weight distribution and high degree of branching (DB). The hyperbranched polyester‐amides synthesized were used as crosslinkers for polyurethane curing systems and the mechanical properties of the polyurethane curing systems were investigated. It was found that the best tensile property and tear strength were obtained when the S2 were used as crosslinkers and the molar ratio of  OH and  NCO was 1 : 1. It was also found that the polyurethane curing systems had the highest hardness and T_g when the S3 were used as crosslinkers. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

New low bandgap conjugated polymer derived from 2, 7‐carbazole and 5, 6‐bis(octyloxy)‐4, 7‐di(thiophen‐2‐yl) benzothiadiazole: Synthesis and photovoltaic properties

To develop conjugated polymers with low bandgap, deep HOMO level, and good solubility, a new conjugated alternating copolymer PC‐DODTBT based on N‐9′‐heptadecanyl‐2,7‐carbazole and 5, 6‐bis(octyloxy)‐4,7‐di(thiophen‐2‐yl)benzothiadiazole was synthesized by Suzuki cross‐coupling polymerization reaction. The polymer reveals excellent solubility and thermal stability with the decomposition temperature (5% weight loss) of 327°C. The HOMO level of PC‐DODTBT is ‐5.11 eV, indicating that the polymer has relatively deep HOMO level. The hole mobility of PC‐DODTBT as deduced from SCLC method was found to be 2.03 × 10^?4 cm²/Versus Polymer solar cells (PSCs) based on the blends of PC‐DODTBT and [6,6]‐phenyl‐C₇₁‐butyric acid methyl ester (PC₇₁BM) with a weight ratio of 1:2.5 were fabricated. Under AM 1.5 (AM, air mass), 100 mW/cm^?2 illumination, the devices were found to exhibit an open‐circuit voltage (V_oc) of 0.73 V, short‐circuit current density (J_sc) of 5.63 mA/cm^?2, and a power conversion efficiency (PCE) of 1.44%. This photovoltaic performance indicates that the copolymer is promising for polymer solar cells applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Structure and morphology of poly(β‐hydroxybutyrate) synthesized by ring‐opening polymerization of racemic (R,S)‐β‐butyrolactone with distannoxane derivatives

Predominantly syndiotactic poly((R,S)‐β‐hydroxybutyrate) (PHB) was synthesized by ring‐opening polymerization of racemic β‐butyrolactone with distannoxane derivatives as catalysts. We have studied the polymerization of (R,S)‐β‐BL using distannoxane derivatives as catalysts and the effects of polymerization time on crude yield and molecular weight of the polymers obtained. Then, a more detailed study of the characterization of polymers obtained using hydroxy‐ and ethoxy‐distannoxanes was performed. ¹³C NMR spectroscopy resolved stereosequences in synthetic PHB at the diad level for the carbonyl carbon and at the triad level for the methylene carbon. These analyses show that distannoxane catalysts produce preferentially syndiotactic polyesters (syndiotactic diads fraction from 0.56 to 0.61). Triad stereosequence distribution of PHB samples agrees favourably with the Bernoullian statistical model of chain‐end control, where ideally Φ = 4(mm) (rr)/(mr + rm)² = 1 for perfect chain‐end control. Polymer samples synthesized from distannoxane catalysts are composed of two distinct transition endotherm components with peak temperatures of approximately 42 °C and 75 °C. The formation of two melting endotherms may be due to the presence of two different crystalline structures. © 2000 Society of Chemical Industry     

Synthesis,Structure Characterization and Biological Activity of Co (II), Cu (II), and Zn (II) Complexes with (Z)‐3‐((3‐hydroxybenzylidene)amino)pyridin‐1‐ium 4‐(dodecan‐4‐yl)benzenesulfonate Surfactant

(Z)‐3‐((3‐hydroxybenzylidene)amino)pyridin‐1‐ium4‐dodecylbenzenesulfonate anionic surfactant and its cobalt, copper and zinc complexes were synthesized (I, I‐Co, I‐Cu and I‐Zn). The chemical structures of it were characterized by elemental analysis, FTIR, ¹H‐NMR, UV–Vis spectroscopy and atomic adsorption. The effects of the chemical structures of the synthesized anionic surfactant and the type of transition metals on the surface activity are presented in this paper. The thermodynamic parameters show that adsorption and micellization processes are spontaneous. The results of biological activity measurements showed that the synthesized compounds have a great efficiency against gram positive (Bacillus subtilis and Staphylococcus aureus), gram‐ negative bacteria (Pseudomonas aeruginosa and Escherichia coli) and fungi (Candida albicans and Aspergillus niger) as well as the sulfate reducing bacteria (Desulfomonas pigra). The complexation of the anionic surfactant with Co²⁺, Cu²⁺ and Zn²⁺ increase the antimicrobial activity values.     

Antimicrobial poly(N‐vinyl‐2‐pyrrolidone‐alt‐maleic anhydride)/poly(ethylene imine) macrocomplexes

The antimicrobial polymer/polymer macrocomplexes were synthesized by radical alternating copolymerization of N‐vinyl‐2‐pyrrolidone with maleic anhydride [poly(VP‐alt‐MA)] with 2,2′‐azobis‐isobutyronitrile as an initiator at 65°C in dioxane solutions under nitrogen atmosphere, and interaction of prepared copolymer with poly(ethylene imine) (PEI) in aqueous solutions. The susceptibility of some Gram‐negative (Salmonella enteritidis and Escherichia coli) and Gram‐positive (Staphylococcus aureus and Listeria monocytogenes) bacteria to the alternating copolymer and its PEI macrocomplexes with different compositions in microbiological medium was studied using pour‐plate technique. All the studied polymers, containing biologically active moieties in the form of ionized cyclic amide, and macrobranched aliphatic amine groups and acid/amine complexed fragments, were more effective against L. monocytogenes than those for Gram‐positive S. aureus bacterium. This fact was explained by different surface layer structural architectures of biomacromolecules of tested bacteria. The resulting polymeric antimicrobial materials are expected to be used in various areas of medicine and food industry. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:5841–5847, 2006     

Photofading of phenylazo‐aniline, ‐pyridone and ‐quinolone disperse dyes on a nylon 6 substrate

The photofading of phenylazo‐aniline, ‐pyridone and ‐quinolone disperse dyes on nylon fabric was analysed using the Kubelka–Munk (K/S) spectra of fabrics exposed to a carbon arc in air. The exposure of dyed fabric through ultraviolet and coloured filters, which do not shield the main absorption band, showed a large decrease in the initial rate (K_PA) of fading. Compared with the K_PA values without filters, the values using filters were half as large for dyes without the nitro groups and a quarter as large for dyes with the nitro groups. The K_PA values may be qualitatively explained by the sum of azo scission (decrease of K/S value at λ_max) and the conversion of nitro groups to nitroso groups. These phenomena occur, respectively, via thermal disproportionation reactions between hydrazinyl radicals (from the azo group) and the reaction between hydrazinyl and N‐centred nitrosyl hydroxide radicals (from the nitro group). The azo scission is promoted by N‐centred nitrosyl hydroxide radicals via the latter reactions.     

Synthesis of 9‐(4‐nitrophenylsulfonyl)‐9H‐carbazole: Comparison of an impedance study of poly[9‐(4‐nitrophenylsulfonyl)‐9H‐carbazole] on gold and carbon fiber microelectrodes

In this study, 9‐(4‐nitrophenylsulfonyl)‐9H‐carbazole (NPhSCz) monomer was chemically synthesized. The monomer characterization was performed by Fourier transform infrared spectroscopy, ¹H‐NMR, and melting point analysis. Two different electropolymerizations of NPhSCz were studied on a gold microelectrode (Au electrode) and carbon fiber microelectrodes (CFMEs) in a 0.1M sodium perchlorate (NaClO₄)/acetonitrile solution. The electropolymerization experiments were done from 1 to 4 mM. The characterizations of two different modified electrodes of poly[9‐(4‐nitrophenylsulfonyl)‐9H‐carbazole] [poly(NPhSCz)] were performed by various techniques, including cyclic voltammetry, scanning electron microscopy–energy‐dispersive X‐ray analysis, and electrochemical impedance spectroscopy (EIS). The effects of the initial monomer concentrations (1, 2, 3, and 4 mM) were examined by EIS. The capacitive behaviors of the modified electrodes were defined via Nyquist, Bode magnitude, Bode phase, and admittance plots. The variation of the low‐frequency capacitance (C_LF) and double‐layer capacitance (C_dl) values are presented at different initial monomer concentrations. Poly(NPhSCz)/CFME was more capacitive (C_LF = 6.66 F/cm² and C_dl ≈ 28 mF) than the Au electrode (C_LF = 6.53 F/cm² and C_dl ≈ 20 mF). An equivalent circuit model of R[QR(CR)(RW)](CR), (R: Current, Q: Constant phase element, C: Double layer capacitance, W: Warburg impedance), was used to fit the theoretical and experimental data. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Novel anti‐bacterial acid dyes derived from naphthalimide: synthesis,characterisation and evaluation of their technical properties on nylon 6

As an attempt to combine the dyeing and functional finishing steps into one process, two novel anti‐bacterial monoazo acid dyes based on N‐ester‐1,8‐naphthalimide were synthesised. To do this, 4‐amino‐N‐ethyl glycinate‐1,8‐naphthalimide was prepared, diazotised and then coupled to thiosalicylic acid or salicylic acid to produce anti‐bacterial dyes. The synthesised dyes were purified and then fully characterised using Fourier Transform–infrared spectrometry, proton nuclear magnetic resonance spectroscopy and melting point analysis. Dispersion of the dyes was prepared in water and applied to nylon 6 fabrics. The novel dyes offered good build‐up properties on the substrate. The anti‐bacterial efficacy of the synthesised dyes was assessed, with the dyes showing activity against both Gram‐positive and Gram‐negative bacteria.     

Dyes derived from 3‐formyl‐2(1H)‐quinolone – synthesis,spectroscopic characterisation,and their behaviour in the presence of sulfhydryl and non‐sulfhydryl amino acids

Novel dyes based on a 3‐formyl‐2(1H)‐quinolone skeleton were synthesised and characterised using ¹H nuclear magnetic resonance spectroscopy and mass spectrometry. The spectroscopic properties of these dyes, such as their absorption spectra, emission spectra, and quantum fluorescence yields, were also examined. The behaviour of the obtained compounds at a pH of 7.4 in the absence and in the presence of thiol amino acids, such as l ‐cysteine, l ‐glutathione, and N‐acetyl‐l ‐cysteine, were studied. The spectroscopic responses of the tested dyes towards other amino acids were also investigated. A reference compound was synthesised to understand the reaction mechanism between the thiols and the obtained dyes. The experimental results show that the synthesised dyes have the potential to act as sensors for thiols.     

Synthesis of 2‐hydroxypropyl dimethylbenzylammonium N,O‐(2‐carboxyethyl) chitosan chloride and its antibacterial activity

N,O‐(2‐carboxyethyl)chitosan (N,O‐2‐CEC) was prepared from chitosan with 3‐chloropropionic acid as modifying agent and NaOH as binding‐acid agent. 2‐Hydroxypropyl dimethylbenzylammonium N,O‐(2‐carboxyethyl) chitosan chloride (HPDMBA‐CEC) was obtained by the reaction of N,O‐2‐CEC with glycidyl dimethyl benzyl ammonium chloride (GDMBA) using NaOH as catalyst. The structures of chitosan derivatives were characterized by FTIR, ¹H NMR, and gel permeation chromatography. The antimicrobial activity of HPDMBA‐CEC was evaluated against a Gram‐negative bacterium Escherichia coli (E.coli) and a Gram‐positive bacterium Staphylococcus aureus (S. aureus). Compared with CTS, N,O‐2‐CEC, and HPDMBA‐CTS, HPDMBA‐CEC had much stronger antimicrobial activity, and this activity increased with increasing substitution degree of quaternary ammonium group (DQ). When the substitution degree of carboxyethylation (DS of CE) was 0.72 and DQ was 0.60, the minimum inhibitory concentrations (MICs) of HPDMBA‐CEC were 3.1 and 6.3 μg/mL against S. aureus and E. coli, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and photochemical reaction of benzo[a]quinoxalino[2,3‐c]phenazine dyes

Novel dyes based on the benzo[a]quinoxalino[2,3‐c]phenazine skeleton and necessary intermediates (benzo[a]phenazine‐5,6‐diones) were synthesized. The heterocyclic dyes and benzo[a]phenazine‐5,6‐diones were characterized using ¹H nuclear magnetic resonance (NMR) spectroscopy and chemical ion (CI) mass spectrometry. Their spectral properties, such as absorption and emission spectra and fluorescence quantum yield, were also measured. Experimental results demonstrated that photolysis of benzo[a]quinoxalino[2,3‐c]phenazine dyes in 2‐propanol and cyclohexene oxide leads to dihydro derivatives. The same product is formed during irradiation of dye/iodonium salt photoredox pairs in monomers. These compounds absorb incident light at longer wavelength and act as in situ sensitizers. Thus, when a composition was irradiated with a xenon lamp through a 395 cutoff filter, higher conversion was achieved than under monochromatic light.