Solid‐state polymerization and characterization of a copolyamide based on adipic acid, 1,4‐butanediamine,and 2,5‐furandicarboxylic acid

2,5‐Furandicarboxylic acid (FDCA) is a promising biobased alternative material to terephthalic acid. In this study, three types of poly(butylene adipamide) (PA‐4,6) containing 10, 20, and 30 mol % of poly(butylene‐2,5‐furandicarboxylamide) (PA‐4,F) were synthesized through consecutive prepolymerization and solid‐state polymerization (SSP). The incorporation of a 10 mol % PA‐4,F component into PA‐4,6 resulted in slight increases in the intrinsic viscosity (IV) and glass‐transition temperature (T_g) after 12 h of SSP at 220 °C. When the SSP temperature and reaction time increased, IV increased proportionally. The highest IV value of 0.75 was obtained by 48 h of SSP at 240 °C, whereas increases in the PA‐4,F content to 20 and 30 mol % gave rise to decreases in IV, T_g, and melting temperature; this interrupted the increase in SSP temperature. The thermal decomposition temperature of the PA‐4,F‐incorporated polyamide was lower than that with PA‐4,6 because of the lower thermal stability of the FDCA component. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43391.     

Synthesis of polyundecamethylene 2,6‐naphthalamide as semiaromatic polyamide‐containing naphthalene ring

A novel engineering plastic polyundecamethylene 2,6‐naphthalamide (PA11N) was prepared via a reaction of 2,6‐naphthalene dicarboxylic acid and 1,11‐undecanediamine through a three‐step procedure. The structure of synthesized PA11N was characterized by elemental analysis, Fourier transform infrared spectroscopy, and proton nuclear magnetic resonance (¹H‐NMR). The thermal behaviors were determined by differential scanning calorimetry, thermogravimetric analysis, and dynamic mechanical analysis. The solubility, water‐absorbing capacity, and mechanical properties of PA11N have also been investigated. Melting temperature (T_m), glass transition temperature (T_g), and decomposition temperature (T_d) of PA11N are 294, 139, and 493°C, respectively. The results show that the heat resistance and mechanical properties of PA11N are near to those of polynonamethylene terephthalamide, and PA11N is a promising heat‐resistant and processable engineering plastic. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Flame retarding mechanism of Polyamide 6 with phosphorus‐nitrogen flame retardant and DOPO derivatives

A novel flame‐retardant composite was prepared by introducing a phosphorus‐nitrogen flame retardant and DOPO‐SiO₂ into PA6. DOPO‐SiO₂ was synthesized successfully in a one‐step process. PA6/OP1314/DOPO‐SiO₂ achieved a UL 94 V‐0 rating with an LOI value of 31%. The maximum mass loss rate of decomposition decreased significantly and char residue increased to 11.6 wt % compared with that of pure PA6. The compacted and dense char was formed due to the combination of the P‐N flame retardant and DOPO‐SiO₂. The complex viscosity of PA6/OP1314/DOPO‐SiO₂ increased considerably which tend to prevent the dripping phenomenon. The flame‐retardant mechanism of PA6/OP1314/DOPO‐SiO₂ was also investigated by Fourier transform infrared spectroscopy FTIR at different temperatures and the pyrolysis products were investigated by pyrolysis gas chromatography/ mass spectrum (Py‐GC/MS). It was assumed that DOPO‐SiO₂ and the hypophosphite of OP1314 possess excellent flame retardancy during the gaseous phase. Meanwhile, melamine and phosphate reacted with the pyrolytic products of PA6 to protect the matrix during the condensed phase. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42932.     

Synthesis of soluble and thermally stable polyimides from 3,5‐diamino‐N‐(4‐(8‐quinolinoxy) phenyl) aniline and various dianhydrides

Three novel polyimides (PIs) having pendent 4‐(quinolin‐8‐yloxy) aniline group were prepared by polycondensation of a new diamine with commercially available tetracarboxylic dianhydrides, such as pyromellitic dianhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and bicyclo[2.2.2]‐oct‐7‐ene‐2,3,5,6‐tetracarboxylic dianhydride. These PIs were characterized by FTIR, ¹H NMR, and elemental analysis; they had high yields with inherent viscosities in the range of 0.4–0.5 dl g⁻¹, and exhibited excellent solubility in many organic solvents such as N,N‐dimethyl acetamide, N,N′‐dimethyl formamide, N‐methyl pyrrolidone (NMP), dimethyl sulfoxide, and pyridine. These PIs exhibited glass transition temperatures (T_g) between 250 and 325° C. Their initial decomposition temperatures (T_i) ranged between 270 and 450°C, and 10% weight loss temperature (T₁₀) up to 500°C with 68% char yield at 600°C under nitrogen atmosphere. Transparent and hard polymer films were obtained via casting from their NMP solutions. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Comparison of thermal degradation characteristics of poly(arylene sulfone)s using thermogravimetric analysis/mass spectrometry

Thermal degradation of poly(arylene sulfone)s had been studied by the combination of thermogravimetric analysis/mass spectrometry (TG/MS) with pyrolysis/gas chromatography/mass spectrometry (Py‐GC/MS) techniques. Through these two methods, the pyrolysates from poly(ether sulfone) (PES) and polysulfone (PSF) were identified in 11 and 21 sets of evolution curves, respectively, from room temperature to 900 °C. Among these pyrolysates, 12 products from PES and 25 products from PSF were obtained. The major mechanism for both PES and PSF was one‐stage pyrolysis involving main chain random scission and carbonization with evolution of SO₂ and phenol as major products. Although the initial thermal stability of PES was lower than that of PSF, the formation of sulfide groups in the condensed phase from PES, through reduction of sulfone group by hydrogen radicals, increased the fire retardation behavior of PES. In PES, the ether and sulfone groups showed similar thermal stability. The thermal stability of functional groups in PSF were in the order of sulfone < ether < isopropylidene group. The scission of the ether group in PSF, with evolution of phenol as the major product, reached maximum evolution amount at the temperature of the maximum thermogravimetry loss of TG (T_max). The scission of isopropylidene groups at high temperature (>580 °C) evolved higher mass derivatives that lower the fire retardancy of PSF. By using a simplified kinetic model, PES showed maximum activation energy with a conversion ratio of 0.2–0.3, which implies a high fire retardant effect of sulfide formation in PES. A comparative study with the proposed model and experimental data showed the theoretical pyrolysis curves to be in agreement with the experimental curves for PES and PSF pyrolysis, respectively. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 2387–2398, 2001     

Synthesis and characterization of nylon‐6/mesoporous silica nanocomposites via in situ synchronous hydrolytic polymerization of tetraethylorthosilicate and ε‐caprolactam

Nylon 6 (N6)/mesoporous silica (MS) nanocomposites (NMSNs) were synthesized via in situ synchronous hydrolytic polymerization of tetraethylorthosilicate (TEOS) and ε‐caprolactam. The novelty of this technique lies in that the nanosilica generated in situ has unique mesoporous structure and ultrahigh‐specific surface area (SSA). Mechanical test showed that, compared to conventional precipitated silica (PS) nanofillers, the MS generated in situ shows better reinforcing efficiency on N6. At a loading of only 3.0 wt % MS, the tensile modulus, flexural modulus, and the heat distortion temperature of NMSNs exhibit increase of 54.8%, 77.9%, and 55.9°C, respectively. The effects of MS on the crystallization behaviors of N6 have been studied by differential scanning calorimetry (DSC), which shows that the incorporation of MS influences the crystallization behaviors of N6 obviously: (1) increases crystallization temperature (T_c) by serving as heterogonous nucleating agent; (2) favors the formation of γ‐phase by hindering the mobility of N6 chains. Dynamic mechanical analysis confirmed that, compared ti that of neat N6, the temperature of the main α‐relaxation (T_α) and the secondary β‐relaxation (T_β) of NMSNs is shifted 6.1°C and 5.3°C toward higher temperature. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis,characterization, and properties of a polyhedral oligomeric octadiphenylsulfonylsilsesquioxane

A novel polyhedral oligomeric octadiphenylsulfonylsilsesquioxane (ODPSS) was synthesized from octaphenylsilsesquioxane and benzenesulfonyl chloride via a Friedel–Crafts reaction with a high yield. ODPSS was identified by Fourier transform infrared spectroscopy, ¹H‐NMR, ¹³C‐NMR, ²⁹Si‐NMR, matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI–TOF MS), wide‐angle X‐ray diffraction, and elemental analysis to be a kind of polyhedral oligomeric silsesquioxane of a T₈R₈ structure. ODPSS exhibited superior thermal stability according to thermogravimetric analysis. Its initial thermal decomposition temperature (T_onset) was at 491°C in air and 515°C in nitrogen. Thermal and mechanical properties of epoxy resin (EP) composites with ODPSS added were studied by differential scanning calorimetry and tensile testing. The results show that the incorporation of ODPSS at a low loading content not only improved the glass‐transition temperature of the EP composites but also enhanced their tensile strength. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40892.     

Synthesis and characterization of new soluble polyamides from an unsymmetrical diamine bearing a bulky triaryl pyridine pendent group

New unsymmetrical diamine monomer containing triaryl pyridine pendent group, 2,4‐diaminophenyl [4‐(2, 6‐diphenyl‐4‐pyridyl) phenyl]ether, was synthesized via aromatic substitution reaction of 1‐chloro‐2,4‐dinitrobenzene with 4‐(2,6‐diphenyl‐4‐pyridyl) phenol, followed by Pd/C‐catalyzed hydrazine reduction. Five Polyamides (PA) were prepared by the phosphorylation polycondensation of different dicarboxylic diacids with the diamine. Inherent viscosities of PAs were in the range 0.51–0.59 g/dL indicating formation of medium molecular weight polymers. The weight and number average molecular weights of a PA, (PA‐d), determined by GPC were 6944 g/mol and 17,369 g/mol, respectively. PAs exhibited glass‐transition temperatures (T_g) in the range 140–235°C. These polymers, essentially amorphous, were soluble in polar aprotic solvents such as DMF, NMP, DMAc, DMSO, pyridine, m‐cresol, and THF. The initial decomposition temperatures (T_i) of PAs, determined by TGA in air, were in the range 300–380°C indicating their good thermal stability. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improved processability of PA66-polyimide copolymers with different polyimide contents

Limitations in the properties of polyamide PA66, such as low glass transition temperature and high water absorptivity, limit its applications. Introduction of amorphous polyimide segments into the PA66 main chain lowers the glass transition temperature and melting temperature and also improves its processability. PA66-polyimide (PA-PI) copolymers with different weight ratios of PI are prepared by high temperature and high-pressure solution polymerization. The degree of crystallization of PA-PI copolymers decreases with increasing PI content. The melting point decreases from 261°C for PA66 to 223°C for PA-PI-4. Dynamic mechanical analysis shows that the T_g increases from 70 to 90°C, and the storage modulus can be well maintained. Rheological studies show that the temperature for processing can reach 70°C. Copolymers with different PI contents show different processing viscosities. In addition, water absorptivity (about 1.8%) and dielectric constant values of PA-PI and PA6/6T are similar.     

A methacrylate monomer bearing nitro,aryl, and hydroxyl side groups: Homopolymerization,characterization, dielectric,and thermal degradation behaviors

2‐Hydroxy‐3‐(4‐nitrophenoxy)propyl methacrylate (HNPPMA) monomer was synthesized. The poly(HNPPMA) was prepared by free radical polymerization (FRP) method. The characterization of poly(HNPPMA) was carried out using FT‐IR, NMR, differential scanning calorimetry, and GPC techniques. The thermal stability and degradation behavior of this polymer have been studied by using thermogravimetry (TG), GC‐MS, NMR, and FT‐IR. The results were in comparison to poly[2‐hydroxy‐3‐(1‐naphtyloxy)propyl methacrylate] sample with α‐naphtyloxy side group prepared by the same method in the our previous study. The effect of thermal activation on non‐isothermal decomposition kinetics of poly(HNPPMA) was investigated using thermogravimetric analysis according to Flynn‐Wall‐Ozawa method. The dielectric measurements of poly(HNPPMA) and doped with europium(III)chloride (EuCI₃) were investigated by impedance analyzer technique in range of 10–4000 Hz frequency by depending on the alternating current conductivities. The mode of thermal degradation including formation of the main products of poly(HNPPMA) degraded from ambient temperature to 500 °C was identified. S°, the cold ring fraction (CRF) was collected from room temperature to 500 °C. The structure of the degradation products has also been studied depending on the GC‐MS analysis. The thermal degradation mechanism for poly(HNPPMA) with radical degradation processes thought to dominate at high temperature was proposed based on GC/MS, NMR, FT‐IR, and taking into account the new products and differences in stability. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43925.     

Thermal degradation of poly(3‐hydroxybutyrate) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) as studied by TG,TG–FTIR,and Py–GC/MS

The thermal degradation kinetics of poly(3‐hydroxybutyrate) (PHB) and poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) [poly(HB–HV)] under nitrogen was studied by thermogravimetry (TG). The results show that the thermal degradation temperatures (T_o, T_p, and T_f) increased with an increasing heating rate (B). Poly(HB–HV) was thermally more stable than PHB because its thermal degradation temperatures, T_o(0), T_p(0), and T_f(0)—determined by extrapolation to B = 0°C/min—increased by 13°C–15°C over those of PHB. The thermal degradation mechanism of PHB and poly(HB–HV) under nitrogen were investigated with TG–FTIR and Py–GC/MS. The results show that the degradation products of PHB are mainly propene, 2‐butenoic acid, propenyl‐2‐butenoate and butyric‐2‐butenoate; whereas, those of poly(HB–HV) are mainly propene, 2‐butenoic acid, 2‐pentenoic acid, propenyl‐2‐butenoate, propenyl‐2‐pentenoate, butyric‐2‐butenoate, pentanoic‐2‐pentenoate, and CO₂. The degradation is probably initiated from the chain scission of the ester linkage. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1530–1536, 2003     

Synthesis and properties of methyl hexahydrophthalic anhydride‐cured fluorinated epoxy resin 2,2‐bisphenol hexafluoropropane diglycidyl ether

The fluorinated epoxy resin, 2,2‐bisphenol hexafluoropropane diglycidyl ether (DGEBHF) was synthesized through a two‐step procedure, and the chemical structure was confirmed by ¹H n uclear magnetic resonance (NMR), ¹³C NMR, and Fourier transform infrared (FTIR) spectra. Moreover, DGEBHF was thermally cured with methyl hexahydrophthalic anhydride (MHHPA). The results clearly indicated that the cured DGEBHF/MHHPA exhibited higher glass transition temperature (T_g 147°C) and thermal decomposition temperature at 5% weight loss (T₅ 372°C) than those (T_g 131.2°C; T₅ 362°C) of diglycidyl ether of bisphenol A (DGEBA)/MHHPA. In addition, the incorporation of bis‐trifluoromethyl groups led to enhanced dielectric properties with lower dielectric constant (D_k 2.93) of DGEBHF/MHHPA compared with cured DGEBA resins (D_k 3.25). The cured fluorinated epoxy resin also gave lower water absorption measured in two methods relative to its nonfluorinated counterparts. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 2801–2808, 2013     

Poly(decamethylene terephthalamide) copolymerized with long‐chain alkyl dodecanedioic acid: Toward bio‐based polymer and improved performances

Poly(decamethylene terephthalamide) (PA10T), a bio‐based high‐performance semi‐aromatic polyamide, has been commercialized in recent years. However, there still are some weaknesses restricting its application range, such as narrow melt processing window and low ductility. In this study, we chose dodecanedioic acid (a potential bio‐based raw material) as the comonomer to prepare copolyamides [poly(decamethylene terephthalamide/decamethylene dodecanediamide), PA10T/1012] for solving these problems. The basic properties of these copolyamides were characterized by viscosity measurement, Fourier transform infrared spectrometer, proton nuclear magnetic resonance, wide‐angle X‐ray diffraction, differential scanning calorimetry, thermogravimetric analysis, dynamic mechanical analysis, and tensile measurement. Results show that, compared to PA10T, PA10T/1012 exhibits wider melt processing window and more outstanding elongation at break. Meanwhile, PA10T/1012 is still qualified for high temperature resistant material. Furthermore, T_g, T_d,5%, T_d,10%, and T_d,max of PA10T/1012 show a linear dependence on 1012 content, which is helpful to design new bio‐based copolyamides for meeting the needs of various occasions. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46531.     

Glycidyl Azide Polymer Crosslinked Through Triazoles by Click Chemistry: Curing,Mechanical and Thermal Properties

Glycidyl azide polymer (GAP) was cured through “click chemistry” by reaction of the azide group with bispropargyl succinate (BPS) through a 1,3‐dipolar cycloaddition reaction to form 1,2,3‐triazole network. The properties of GAP‐based triazole networks are compared with the urethane cured GAP‐systems. The glass transition temperature (T_g), tensile strength, and modulus of the system increased with crosslink density, controlled by the azide to propargyl ratio. The triazole incorporation has a higher T_g in comparison to the GAP‐urethane system (T_g−20 °C) and the networks exhibit biphasic transitions at 61 and 88 °C. The triazole curing was studied using Differential Scanning Calorimetry (DSC) and the related kinetic parameters were helpful for predicting the cure profile at a given temperature. Density functional theory (DFT)‐based theoretical calculations implied marginal preference for 1,5‐addition over 1,4‐addition for the cycloaddition between azide and propargyl group. Thermogravimetic analysis (TG) showed better thermal stability for the GAP‐triazole and the mechanism of decomposition was elucidated using pyrolysis GC‐MS studies. The higher heat of exothermic decomposition of triazole adduct (418 kJ ⋅ mol⁻¹) against that of azide (317 kJ ⋅ mol⁻¹) and better mechanical properties of the GAP‐triazole renders it a better propellant binder than the GAP‐urethane system.     

Reactive blends of polyamide 6 with polyester elastomer using coupling agents

In situ compatibilized melt blends of polyamide 6 (PA‐6) with polyester elastomer (PEL) were prepared in a corotating twin‐screw extruder using two types of coupling agent (CA): diglycidyl ether of bisphenol A (DGEBA) and 1,4‐phenylene bis(2‐oxazoline) (PBO). The notched impact strength of PA‐6 and PA‐6/PEL blends increased with the addition of coupling agent, especially DGEBA, and the maximum impact toughening of the blend was obtained with 0.6 mol % DGEBA, the composition of minimum domain size observed from SEM. Viscosities of the untreated blends increased over those of the base resins at low frequencies. Viscosities of both the base resins and the blends increased with the addition of CA, and the effect was much more pronounced with DGEBA, especially for PA‐6 and PA‐6–rich blends. The crystallization temperature (T_c) of PEL increased over 10°C, whereas the T_c of PA‐6 decreased by 2–3°C in the blends. With the addition of coupling agents, the crystallization melting temperature (T_m) and T_c of PA‐6 decreased by up to 5°C with DGEBA, implying that the crystallization of PA‐6 is disturbed by the in situ formed PA‐6–CA–PEL or PA‐6–CA–PA‐6 type copolymer. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3966–3973, 2004     

Compatibility of poly(vinylidene fluoride) (PVDF)/polyamide 12 (PA12) blends

Poly(vinylidene fluoride) (PVDF)/polyamide 12 (PA12) blends showed new peaks in XRD profile with increasing PA12 and the crystallinity of PA12 significantly decreased with the addition of PVDF. PVDF showed three relaxation regions at about −40, 40, and 100°C, respectively, and glass transition temperature (T_g ) of PA12 increased in blends (10.8→30.14°C) and α‐relaxation of PVDF decreased from 100.26 to 86.46°C. Complex viscosities (η*) vs. composition curve showed a great positive deviation in PVDF‐rich and a small negative deviation in PA12‐rich blends. The N—H and C=O stretching band of PA12 shifted slightly toward higher wavelength, and from curve‐fitted data the area of hydrogen‐bonded C=O stretching bands of PA12 decreased with the addition of PVDF, especially in the 30/70 blend, implying the existence of interactions between the β‐hydrogen atom of PVDF and amide carbonyl group of PA12 in the blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1374–1380, 2000     

The pyrolysis behaviors of ternary copolyimide derived from aromatic dianhydride and aromatic diisocyanates

A polyimide (PI) based on benzophenone‐3,3′,4,4′‐tetracarboxylic acid dianhydride, toluene diisocyanate (TDI), and 4,4′‐methylenebis (phenyl isocyanate) (MDI) has been synthesized via a one‐step polycondensation procedure. The resulting PI possessed excellent thermal stability with the glass transition temperature (T_g) 316°C, the 5% weight loss temperature (T_5%) in air and nitrogen 440.4°C and 448.0°C, respectively. The pyrolysis behaviors were investigated with dynamic thermogravimetric analysis (TGA), TGA coupled with Fourier transform infrared spectrometry (TGA–FTIR) and TGA coupled with mass spectrometry (TGA–MS) under air atmosphere. The results of TGA–FTIR and TGA–MS indicated that the main decomposition products were carbon dioxide (CO₂), carbonic oxide (CO), water (H₂O), ammonia (NH₃), nitric oxide (NO), hydrogen cyanide (HCN), benzene (C₆H₆), and compounds containing NH₂, C?N, N?C?O or phenyl groups. The activation energy (E_a) of the solid‐state process was estimated using Ozawa–Flynn–Wall (OFW) method which resulted to be 143.8 and 87.8 kJ/mol for the first and second stage. The pre‐exponential factor (A) and empirical order of decomposition (n) were determined by Friedman method. The activation energies of different mechanism models were calculated from Coats–Redfern method. Compared with the activation energy values obtained from the OFW method, the actual reaction followed a random nucleation mechanism with the integral form g(α) = ?ln(1 ? α). © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40163.     

Preparation of heat‐resistant branched poly(styrene‐alt‐NPMI) by ATRP with divinylbenzene as the branching agent

Heat‐resistant branched poly(styrene‐alt‐NPMI) has been prepared via atom transfer radical polymerization (ATRP) of styrene (St) and N‐phenyl maleimide (NPMI) with divinylbenzene (DVB) as the branching agent in anisole at 80°C. Gas chromatography (GC) was used to determine the conversion of the reactants. Triple detection gel permeation chromatography (TD‐GPC) was used to analyze the copolymers. The results show that the polymerization yields primary chains predominately in the early stages and the formation of branched molecules occurs mainly when conversion is higher than 50%. As expected, higher dosage of DVB in our investigation range favors the formation of polymers with higher degree of branching. All the resulting branched poly(styrene‐alt‐NPMI)s have glass transition temperature (T_g) above 175°C, extrapolated initial weight loss temperature (T_i) above 410°C and statistic heat‐resistant index above 200°C. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Structural evolution of the R‐T phase boundary in KNN‐based ceramics

Although a rhombohedral‐tetragonal (R‐T) phase boundary is known to substantially enhance the piezoelectric properties of potassium‐sodium niobate ceramics, the structural evolution of the R‐T phase boundary itself is still unclear. In this work, the structural evolution of R‐T phase boundary from ?150°C to 200°C is investigated in (0.99?x)K_0.5Na_0.5Nb_1?ySb_yO₃–0.01CaSnO₃–xBi_0.5K_0.5HfO₃ (where x = 0‐0.05 with y = 0.035, and y = 0‐0.07 with x = 0.03) ceramics. Through temperature‐dependent powder X‐ray diffraction (XRD) patterns and Raman spectra, the structural evolution was determined to be Rhombohedral (R, <?125°C)→Rhombohedral + Orthorhombic (R + O, ?125°C to 0°C)→Rhombohedral + Tetragonal (R + T, 0 °C to 150°C)→dominating Tetragonal (T, 200°C to Curie temperature (T_C)) → Cubic (C, >T_C). In addition, the enhanced electrical properties (e.g., a direct piezoelectric coefficient (d₃₃) of ~450 ± 5 pC/N, a conversion piezoelectric coefficient () of ~580 ± 5 pm/V, an electromechanical coupling factor (k_p) of ~0.50 ± 0.02, and T_C~250°C), fatigue‐free behavior, and good thermal stability were exhibited by the ceramics possessing the R‐T phase boundary. This work improves understanding of the physical mechanism behind the R‐T phase boundary in KNN‐based ceramics and is an important step toward their adoption in practical applications.     

Preparation,thermo‐optic property and transmission loss of chiral azobenzene polyurethane

A novel chiral azobenzene polyurethane (CAPU) was prepared from chromophore, chiral reagent L (?)‐tartaric acid and toluene diisocyanate (TDI). The chemical structure and the thermal property were characterized by UV‐Vis spectrum, FT‐IR, ¹H NMR, circular dichroism (CD) spectrum, differential scanning calorimeter (DSC) and thermogravimetric analysis (TGA). DSC and TGA experiments showed that the glass transition temperature (T_g) and the decomposition temperature (T_d) at 5% mass loss were 110°C and 199°C, respectively. The refractive index (n) and thermo‐optic coefficient (dn/dT) of the CAPU were measured at 650 nm wavelength and different temperature by attenuated total reflection (ATR) technique. By using CCD digital imaging devices, transmission loss of CAPU was measured and the value is 0.565dB/cm. The results will provide the foundation for many potential applications such as digital thermo‐optic switch materials and other fields in the future. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011