Biodegradable poly(vinyl alcohol)‐graft‐ poly(ε‐caprolactone) comb‐like polyester: Microwave synthesis and its characterization

Poly(vinyl alcohol)‐initiated microwave‐assisted ring opening polymerization of ε‐caprolactone in bulk was investigated, and a series of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) (PVA‐g‐PCL) copolymers were prepared, with the degree of polymerization (DP) of PCL side chains and the degree of substitution (DS) of PVA by PCL being in the range of 3–24 and 0.35–0.89, respectively. The resultant comb‐like PVA‐g‐PCL copolymers were confirmed by means of FTIR, ¹H NMR, and viscometry measurement. The introduction of hydrophilic backbone resulted in the decrease in both melting point and crystallization property of the PVA‐g‐PCL copolymers comparing with linear PCL. With higher microwave power, the DP of PCL side chains and DS of PVA backbone were higher, and the polymerization reaction proceeded more rapidly. Both the DP and monomer conversion increased with irradiation time, while the DS increased first and then remained constant. With initiator in low concentration, the DP and DS were higher, while the monomer was converted more slowly. Microwaves dramatically improved the polymerization reaction in comparison of conventional heating method. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104, 3973–3979, 2007     

Amphiphilic linear–hyperbranched polymer poly(ethylene glycol)–branched polyethylenimine–poly(ϵ‐caprolactone): synthesis,self‐assembly and application as stabilizer of platinum nanoparticles

Amphiphilic linear–hyperbranched polymer poly(ethylene glycol)–branched polyethylenimine–poly(?‐caprolactone) (PEG‐PEI‐PCL) was synthesized by progressively conjugating PEG (one chain) and PCL (multi‐chains) to PEI (hyperbranched architecture) with a yield of 87%. PEG‐PEI‐PCL forms nano‐sized uniform spherical micelles by self‐assembly in water. The micelles had an average diameter of 56 nm determined using dynamic light scattering and 35 nm observed from transmission electron microscopy images. PEG‐PEI‐PCL was used as a stabilizer of platinum nanoparticles (PtNPs) for the first time. The particle diameter of PEG‐PEI‐PCL‐stabilized PtNPs was 7.8 ± 1.4 nm. Amphiphilic (hydrophilic–hydrophilic–hydrophobic) and hyperbranched (linear–hyperbranched–grafted) structures enabled PtNPs to effectively stabilize and disperse in liquid‐phase synthesis. The highly disperse PtNPs in PEG‐PEI‐PCL micelles improved the catalytic activity for the reduction of 4‐nitrophenol with a catalytic yield of near 100%. © 2016 Society of Chemical Industry     

Synthesis and characterization of novel urethane‐siloxane copolymers with a high content of PCL‐PDMS‐PCL segments

Novel polyurethane copolymers derived from 4,4′‐methylenediphenyl diisocyanate (MDI), 1,4‐butanediol (BD) and α,ω‐dihydroxy‐[poly(caprolactone)‐poly (dimethylsiloxane)‐poly(caprolactone)] (α,ω‐dihydroxy‐(PCL‐PDMS‐PCL); = 6100 g mol^?1) were synthesized by a two‐step polyaddition reaction in solution. In the synthesis of the polyurethanes, the PCL blocks served as a compatibilizer between the nonpolar PDMS blocks and the polar comonomers, MDI and BD. The synthesis of thermoplastic polyurethanes (TPU) with high soft segment contents was optimized in terms of the concentrations of the reactants, the molar ratio of the NCO/OH groups, and the time and temperature of the polyaddition reaction. The structure, composition, and hard MDI/BD segment length of the synthesized polyurethane copolymers were determined by ¹H, ¹³C‐NMR, and two‐dimensional correlation (COSY, HSQC, and HMBC) spectroscopy, while the hydrogen bonding interactions in the copolymers were analyzed by FT‐IR spectroscopy. The influence of the reaction conditions on the structure, molecular weight, thermal, and some physical properties was studied at constant composition of the reaction mixture. A change in the molar ratio of the NCO/OH groups and the reaction conditions modified not only the molecular weight of the synthesized polyurethanes, but also the microstructure and therefore the thermal and physical properties of the copolymers. It was demonstrated that only PCL segments with high soft segment contents crystallize, thereby showing spherulitic morphology. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

In Situ synthesis of multiblock copolymers of poly(ϵ‐caprolactone) with different poly(ether diols) based polyurethane by reactive extrusion

Polyurethanes with multiblock copolymers of poly(?‐caprolactone) (PCL) and poly(tetramethylene oxide) glycol (PTMG) or poly(ethylene glycol) (PEG) as a soft segment were synthesized in situ via reactive extrusion from ?‐caprolactone (CL) and 4,4′‐diphenylmethane diisocyanate (MDI). The titanium alkoxide mixture generated from an ester‐exchange reaction between titanium propoxide [Ti(OPr)₄], and excessive PTMG or PEG was used as an initiator and catalyst. Compared to the reported fabrication of polycaprolactone‐based polyurethane (PCLU), the in situ reactive extrusion preparation not only explored a new rapid route for the fabrication of PCLU but also offered a simplified, controllable approach for the production of PCLU in a successive mass scale. A series of PTMG–PCLUs and PEG–PCLUs with different PCL block‐average degrees of polymerization (DP_n's) were prepared by only an adjustment of the relative concentration of CL in the reaction system, with a certain constant molar ratio of MDI to titanium alkoxide. ¹H‐NMR, gel permeation chromatography, and differential scanning calorimetry results indicate that all of the CL monomers were converted in the polymerization, and the molecular weight of the copolymers was about 8 × 10⁴ g/mol with a polydispersity index of approximate 2.4. With an increase in the PCL block‐average DP_n in PTMG–PCLU from 25 to 40, the tensile strength increased from 16.5 to 22.7 MPa, and the melting point increased from 46.1 to 49.5°C. It was also verified by PEG–PCLU prepared with organic Ti of lowered content in the initiator mixture that the mechanical properties could be greatly affected and dropped with decreasing content of organic Ti in the initiator mixture. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Miscibility of block copolymers of poly(ε‐caprolactone) and poly(ethylene glycol) with poly(3‐hydroxybutyrate) as well as the compatibilizing effect of these copolymers in blends of poly(ε‐caprolactone) and poly(3‐hydroxybutyrate)

Atactic poly(3‐hydroxybutyrate) (a‐PHB) and block copolymers of poly(ethylene glycol) (PEG) with poly(ε‐caprolactone) (PCL‐b‐PEG) were synthesized through anionic polymerization and coordination polymerization, respectively. As demonstrated by differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) measurements, both chemosynthesized a‐PHB and biosynthesized isotactic PHB (i‐PHB) are miscible with the PEG segment phase of PCL‐b‐PEGs. However, there is no evidence showing miscibility between both PHBs and the PCL segment phase of the copolymer even though PCL has been block‐copolymerized with PEG. Based on these results, PCL‐b‐PEG was added, as a compatibilizer, to both the PCL/a‐PHB blends and the PCL i‐PHB blends. The blend films were obtained through the evaporation of chloroform solutions of mixed components. Excitingly, the improvement in mechanical properties of PCL/PHB blends was achieved as anticipated initially upon the addition of PCL‐b‐PEG. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2600–2608, 2001     

Synthesis and properties of novel biodegradable poly(ε‐caprolactone)/ poly(ethylene glycol)‐based polyurethane elastomers

Elastomeric polyurethanes with tunable biodegradation properties and suitable for numerous biomedical applications were synthesized via reaction of epoxy‐terminated polyurethanes (EUPs) with 1,6‐hexamethylenediamine as curing agent. The EUPs themselves were prepared from glycidol and isocyanate‐terminated polyurethanes made from poly(ε‐caprolactone) (PCL) or poly(ethylene glycol) (PEG) and 1,6‐hexamethylene diisocyanate. All the polymers were characterized by conventional methods, and their physical, mechanical, thermal, and degradation properties were studied. The results showed that the degradation rate and mechanical properties of the final products can be controlled by the amount of PEG or PCL present in the EUP. Increasing the PEG content causes an increase of hydrolytic degradation rate, and increasing the PCL content improves the mechanical properties of the final products. Evaluation of cytotoxcicity showed nontoxic behavior of the prepared samples, but the cytocompatibility of these polymers needs to be improved. Copyright © 2006 Society of Chemical Industry     

Biodegradable and photocurable multiblock copolymers with shape‐memory properties from poly(ε‐caprolactone) diol,poly(ethylene glycol), and 5‐cinnamoyloxyisophthalic acid

Biodegradable and photocurable multiblock copolymers of various compositions were synthesized by the high‐temperature solution polycondensation of poly(ε‐caprolactone) (PCL) diols of molecular weight (M_n) = 3000 and poly(ethylene glycol)s (PEG) of M_n = 3000 with a dichloride of 5‐cinnamoyloxyisophthalic acid (ICA) as a chain extender, followed by irradiation by a 400 W high‐pressure mercury lamp (λ > 280 nm) to form a network structure. The gel contents increased with photocuring time, reaching a level of over 90% after 10 min for all copolymers without a photoinitiator. The thermal and mechanical properties of the photocured copolymers were examined by DSC and tensile tests. In cyclic thermomechanical tensile tests, the photocured ICA/PCL/PEG copolymer films showed good shape‐memory properties at 37–60°C, with both shape fixity ratio and shape recovery ratio over 90% at a maximum tensile strain of 100–300%. The water absorption of these copolymers and their rate of degradation in a phosphate buffer solution (pH 7.0) at 37°C increased significantly with increasing PEG content. The novel photocured ICA/PCL/PEG multiblock copolymers are potentially useful in biomedical applications. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Self‐assembled micelles prepared from poly(ɛ‐caprolactone)–poly(ethylene glycol) and poly(ɛ‐caprolactone/glycolide)–poly(ethylene glycol) block copolymers for sustained drug delivery

A series of poly(?‐caprolactone)–poly(ethylene glycol) (PCL‐PEG) and poly(?‐caprolactone/glycolide)–poly(ethylene glycol) [P(CL/GA)‐PEG] diblock copolymers were prepared by ring‐opening polymerization of ?‐caprolactone or a mixture of ?‐caprolactone and glycolide using monomethoxy PEG (mPEG) as macroinitiator and Sn(Oct)₂ as catalyst. The resulting copolymers were characterized using ¹H‐NMR, gel permeation chromatography, differential scanning calorimetry, and wide‐angle X‐ray diffraction. Copolymer micelles were prepared using the nanoprecipitation method. The morphology of the micelles was spherical or worm‐like as revealed by transmission electron microscopy, depending on the copolymer composition and the length of the hydrophobic block. Introduction of the glycolide component, even in small amounts (CL/GA = 10), disrupted the chain structure and led to the formation of spherical micelles. Interestingly, the micelle size decreased with the encapsulation of paclitaxel. Micelles prepared from mPEG5000‐derived copolymers exhibited better drug loading properties and slower drug release than those from mPEG2000‐derived copolymers. Drug release was faster for copolymers with shorter PCL blocks than for those with longer PCL chains. The introduction of glycolide moieties enhanced drug release, but the overall release rate did not exceed 10% in 30 days. In contrast, drug release was enhanced in acidic media. Therefore, these bioresorbable micelles and especially P(CL/GA)‐PEG micelles with excellent stability, high drug loading content, and prolonged drug release could be promising for applications as drug carriers. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45732.     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Synthesis and characterization of poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers by combined ring‐opening polymerization and cross‐coupling processes

2,5‐Dibromo‐1,4‐(dihydroxymethyl)benzene was used as initiator in ring‐opening polymerization of ε‐caprolactone in the presence of stannous octoate (Sn(Oct)₂) catalyst. The resulting poly(ε‐caprolactone) (PCL) macromonomer, with a central 2,5‐dibromo‐1,4‐diphenylene group, was used in combination with 1,4‐dibromo‐2,5‐dimethylbenzene for a Suzuki coupling in the presence of Pd(PPh₃)₄ as catalyst or using the system NiCl₂/bpy/PPh₃/Zn for a Yamamoto‐type polymerization. The poly(p‐phenylenes) (PPP) obtained, with PCL side chains, have solubility properties similar to those of the starting macromonomer, ie soluble in common organic solvents at room temperature. The new polymers were characterized by ¹H and ¹³C NMR and UV spectroscopy and also by GPC measurements. The thermal behaviour of the precursor PCL macromonomer and the final poly(p‐phenylene)‐graft‐poly(ε‐caprolactone) copolymers were investigated by thermogravimetric analysis and differential scanning calorimetry analyses and compared. Copyright © 2004 Society of Chemical Industry     

Synthesis and aggregation behavior of four types of different shaped PCL‐PEG block copolymers

Biodegradable, amphiphilic, linear (diblock and triblock) and star‐shaped (three‐armed and four‐armed) poly[(ethylene glycol)‐block‐(ε‐caprolactone)] copolymers (PEG–PCL copolymers) were synthesized by ring‐opening polymerization of ε‐caprolactone (CL) with stannous octoate as a catalyst, in the presence of monomethoxypoly(ethylene glycol) (MPEG), poly(ethylene glycol) (PEG), three‐armed poly(ethylene glycol) (3‐arm PEG) or four‐armed poly(ethylene glycol) (4‐arm PEG) as an initiator, respectively. The monomer‐to‐initiator ratio was varied to obtain copolymers with various PEG weight fractions in a range 66–86%. The molecular structure and crystallinity of the copolymers, and their aggregation behavior in the aqueous phase, were investigated by employing ¹H‐NMR spectroscopy, gel permeation chromatography and differential scanning calorimetry, as well as utilizing the observational data of gel–sol transitions and aggregates in aqueous solutions. The aggregates of the PEG–PCL block copolymers were prepared by directly dissolving them in water or by employing precipitation/solvent evaporation technique. The enthalpy of fusion (ΔH_m), enthalpy of crystallization (ΔH_crys) and degrees of crystallinity (χ_c) of PEG blocks in copolymers and the copolymer aggregates in aqueous solutions were influenced by their PEG weight fractions and molecular architecture. The gel–sol transition properties of the PEG–PCL block copolymers were related to their concentrations, composition and molecular architecture. Copyright © 2006 Society of Chemical Industry     

Porous biodegradable polyester blends of poly(L‐lactic acid) and poly(ε‐caprolactone): physical properties,morphology, and biodegradation

Poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their films without or blended with 50 wt% poly(ethylene glycol) (PEG) were prepared by solution casting. Porous films were obtained by water‐extraction of PEG from solution‐cast phase‐separated PLLA‐blend‐PCL‐blend‐PEG films. The effects of PLLA/PCL ratio on the morphology of the porous films and the effects of PLLA/PCL ratio and pores on the physical properties and biodegradability of the films were investigated. The pore size of the blend films decreased with increasing PLLA/PCL ratio. Polymer blending and pore formation gave biodegradable PLLA‐blend‐PCL materials with a wide variety of tensile properties with Young's modulus in the range of 0.07–1.4 GPa and elongation at break in the range 3–380%. Pore formation markedly increased the PLLA crystallinity of porous films, except for low PLLA/PCL ratio. Polymer blending as well as pore formation enhanced the enzymatic degradation of biodegradable polyester blends. Copyright © 2006 Society of Chemical Industry     

A statistical study of poly(ε‐caprolactone) crystallinity in poly(ε‐caprolactone)–silica sol–gel materials and their in vitro calcium phosphate‐forming ability

Composite poly(ε‐caprolactone) (PCL)–silica materials for potential use in orthopaedic applications have been prepared by a sol–gel method using an experimental design approach to investigate the effect of synthesis variables, separately and together, on the physical form of the organic polymer. A combination of differential scanning calorimetry, X‐ray diffraction and Fourier‐transform infrared methods were used to obtain information on the arrangement of the organic polymer in the hybrid material. As our studies investigated the effect of synthesis variables simultaneously, it was possible to establish that the increase of tetraethyl orthosilicate (TEOS)/PCL and HCl/TEOS molar ratios decreased the poly(ε‐caprolactone) crystallinity and provided for a better mixing of the two phases. At a mechanistic level it was possible to show that increase in catalyst content affected the condensation of silicon containing species. In vitro calcium phosphate‐forming ability tests using the static biomimetic method have been carried out on selected PCL–silica sol–gels. In vitro bioactivity was only observed for PCL–silica sol–gel composites with high silica content (30% weight). Changes in catalyst levels had a smaller but still significant effect. Calcium phosphate formation on largely non‐porous surfaces is proposed to occur via the formation of a silica sol–gel layer, and is influenced by the topography and the chemistry of the materials surface. Copyright © 2003 Society of Chemical Industry     

Rapid synthesis of new block copolyurethanes derived from L‐leucine‐PEG in ionic liquids under microwave irradiation

This study concerns the synthesis of novel multi block polyurethane (PU) copolymers containing eco‐friendly segments, taking the advantage of ionic liquids (IL)s under microwave irradiation. For this, L ‐leucine anhydride cyclodipeptide (LAC) was prepared and then a new class of poly(ether‐urethane‐urea)s (PEUUs) was synthesized with two types of ILs, including room temperature imidazolium (RTIL)s and molten ammonium type ILs. ILs were used as reaction media and PUs were prepared via two‐step polymerization method. Polymerization reaction was also conducted under conventional heating method in N‐methyl pyrrolidone (NMP) as reaction solvent. In the first step, 4,4′‐methylene‐bis(4‐phenylisocyanate) (MDI) was reacted with LAC to produce isocyanate‐terminated poly(imide‐urea) oligomers as hard segment. Chain extension of the resulting prepolymer with polyethyleneglycol (PEG) of molecular weights of 400 (PEG‐400) was the second step to furnish a series of new PEUUs. These multiblock copolymers are optically active, thermally stable and soluble in amide‐type solvents. PEUUs prepared in ILs under microwave irradiation showed more phase separation and crystallinity than PEUU prepared under conventional method. Some structural characterization and physical properties of these PEUUs, prepared under different methods, are reported and compared. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Confined crystallization morphology of poly(ϵ‐caprolactone) block within poly(ϵ‐caprolactone)–poly(l‐lactide) copolymers

The confined crystallization of poly(?‐caprolactone) (PCL) block in poly(?‐caprolactone)–poly(l ‐lactide) (PCL‐PLLA) copolymers was investigated using differential scanning calorimetry, polarized optical microscopy, scanning electronic microscopy and atomic force microscopy. To study the effect of crystallization and molecular chain motion state of PLLA blocks in PCL‐PLLA copolymers on PCL crystallization morphology, high‐temperature annealing (180 °C) and low‐temperature annealing (80 °C) were applied to treat the samples. It was found that the crystallization morphology of PCL block in PCL‐PLLA copolymers is not only related to the ratio of block components, but also related to the thermal history. After annealing PCL‐PLLA copolymers at 180 °C, the molten PCL blocks are rejected from the front of PLLA crystal growth into the amorphous regions, which will lead to PCL and PLLA blocks exhibiting obvious fractionated crystallization and forming various morphologies depending on the length of PLLA segment. On the contrary, PCL blocks more easily form banded spherulites after PCL‐PLLA copolymers are annealed at 80 °C because the preexisting PLLA crystal template and the dangling amorphous PLLA chains on PCL segments more easily cause unequal stresses at opposite fold surfaces of PCL lamellae during the growth process. Also, it was found that the growth rate of banded spherulites is less than that of classical spherulites and the growth rate of banded spherulites decreases with decreasing band spacing. © 2019 Society of Chemical Industry     

Poly(ethyl glycol) assisting water sorption enhancement of poly(ε‐caprolactone) blend for drug delivery

Poly(ε‐caprolactone) (PCL) has been thermally synthesized, and then fractionated to blend with poly(ethyl glycol) (PEG). Blend films of PCL and PEG have been prepared by solution casting. Fourier transform infrared spectrum and differential scanning calorimetry of the films have been carried out, and the results indicate some hydrogen bonding interaction between the two components, which is resulted from the carbonyl groups of PCL and the hydroxyl end‐groups of the low‐molecular‐weight PEG. Scanning electron microscope images of the blend films reveal porous network structures for their surfaces and for their inner parts and the porous structure becomes more pronounced with the increase of PEG in the blend film. Ibuprofen (IBU) was used as the model drug to test the drug release behavior for the PCL/PEG blend matrices. The results show that IBU could be released from the blend tablets rapidly, and the release rate increases with PEG content. Analysis of the release profiles indicates PCL erosion control release mechanism of pure PCL tablet, but drug diffusion control of the blend tablet, because PEG can absorb water to allow water feasible to diffuse into drug core and dissolve drug. Therefore, the interconnected channels in the blend matrices and the hydrophilic nature of PEG contribute to the improvement of the IBU release rate. The research indicates that drug release rate from PCL based material could be efficiently improved by addition of small amount of hydrophilic low‐molecular‐weight PEG. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol) block copolymers prepared by a salicylaldimine‐aluminum complex

A series of poly(?‐caprolactone)‐b‐poly(ethylene glycol) (PCL‐b‐PEG) block copolymers with different molecular weights were synthesized with a salicylaldimine‐aluminum complex in the presence of monomethoxy poly(ethylene glycol). The block copolymers were characterized by ¹H NMR, GPC, WAXD, and DSC. The ¹H NMR and GPC results verify the block structure and narrow molecular weight distribution of the block copolymers. WAXD and DSC results show that crystallization behavior of the block copolymers varies with the composition. When the PCL block is extremely short, only the PEG block is crystallizable. With further increase in the length of the PCL block, both blocks can crystallize. The PCL crystallizes prior to the PEG block and has a stronger suppression effect on crystallization of the PEG block, while the PEG block only exerts a relatively weak adverse effect on crystallization of the PCL block. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers with dibutylmagnesium as catalyst

Two series of poly(ε‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ε‐caprolactone) triblock copolymers were prepared by the ring opening polymerization of ε‐caprolactone in the presence of poly(ethylene glycol) and dibutylmagnesium in 1,4‐dioxane solution at 70°C. The triblock structure and molecular weight of the copolymers were analyzed and confirmed by ¹H NMR, ¹³C NMR, FTIR, and gel permeation chromatography. The crystallization and thermal properties of the copolymers were investigated by wide‐angle X‐ray diffraction (WAXD) and differential scanning calorimetry (DSC). The results illustrated that the crystallization and melting behaviors of the copolymers were depended on the copolymer composition and the relative length of each block in copolymers. Crystallization exothermal peaks (T_c) and melting endothermic peaks (T_m) of PEG block were significantly influenced by the relative length of PCL blocks, due to the hindrance of the lateral PCL blocks. With increasing of the length of PCL blocks, the diffraction and the melting peak of PEG block disappeared gradually in the WAXD patterns and DSC curves, respectively. In contrast, the crystallization of PCL blocks was not suppressed by the middle PEG block. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Ultrasonochemical‐assisted fabrication and evaporation‐ induced self‐assembly (EISA) of POSS‐SiO2@Ag core/ABA triblock copolymer nanocomposite film

Poly(ethylene glycol)‐octafunctionalized polyhedral oligomeric silsesquioxane (POSS) (M_n = 5576.6 g/mol) alloying agent stabilized amphiphilic silica@silver metalloid nanocomposite blended with a triblock copolymer poly(p‐dioxanone‐co‐caprolactone)‐block‐poly(ethylene oxide)‐block‐poly(p‐dioxanone‐co‐caprolactone) (POSS‐SiO₂@Ag/PPDO‐co‐PCL‐b‐PEG‐b‐PPDO‐co‐PCL) has been synthesized in both water and in organic medium utilizing ultrasonochemical reaction. The POSS stabilized pre‐made metalloid was successfully dispersed in amphiphilic PPDO‐co‐PCL‐b‐PEG‐b‐PPDO‐co‐PCL (ABA) triblock copolymer matrix of molecular weight 45.9 × 10⁴ g/mol. The mechanism of synthesis of high concentration of SiO₂@Ag nanocomposite from TEOS/AgNO₃ (in the presence of NH₄OH as catalyst/NaBH₄ as reductant) nonmetal/metal precursors and the successful EISA of POSS‐SiO₂@Ag/ABA nanocomposite into films has been discussed. The successful synthesis of metalloid nanocomposite was morphologically accessed by field emission‐scanning electron microscopy, transmission electron microscopy and atomic force microscopy. Surface plasmon resonance was ensured from UV–visible spectral analysis. Identity and the crystallinity of as prepared nanocomposite were studied by X‐ray diffractometer. Structural and luminescence properties of the nanocomposite were examined by Fourier transform infrared spectroscopy and photoluminescence. Thermogravimetric analysis was carried out to study the thermal stability of the resulting hybrid nanocomposite. The resultant inorganic–organic nanocomposite can be easily suspended in water and would be useful in variety of applications. POLYM. COMPOS., 31:1620–1627, 2010. © 2009 Society of Plastics Engineers     

Preparation of poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filament by melt spinning

Poly(ε‐caprolactone)/poly(ε‐caprolactone‐co‐lactide) (PCL/PLCL) blend filaments with various ratios of PCL and PLCL were prepared by melt spinning. The effect of PLCL content on the physical properties of the blended filament was investigated. The melt spinning of the blend was carried out and the as spun filament was subsequently subjected to drawing and heat setting process. The addition of PLCL caused significant changes in the mechanical properties of the filaments. Crystallinity of blend decreased with the addition of PLCL as observed by X‐ray diffraction (XRD) and differential scanning calorimetry (DSC). Scanning electron microscopy (SEM) revealed that the fracture surface becomes rougher at higher PLCL content. It may be proposed that PCL and PLCL show limited interaction within the blend matrix. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012