Effect of lactic acid chain length on thermomechanical properties of star‐LA‐xylitol resins and jute reinforced biocomposites

Star‐shaped bio‐based resins were synthesized by direct condensation of lactic acid (LA) with xylitol followed by end‐functionalizing of branches by methacrylic anhydride with three different LA chain lengths (3, 5 and 7). The thermomechanical and structural properties of the resins were characterized by ¹³C NMR, Fourier transform IR spectroscopy, rheometry, DSC, dynamic mechanical analysis (DMA), TGA and flexural and tensile tests. An evaluation of the effect of chain length on the synthesized resins showed that the resin with five LAs exhibited the most favorable thermomechanical properties. Also, the resin's glass transition temperature (103 °C) was substantially higher than that of the thermoplast PLA (ca 55 °C). The resin had low viscosity at its processing temperature (80 °C). The compatibility of the resin with natural fibers was investigated for biocomposite manufacturing. Finally, composites were produced from the n5‐resin (80 wt% fiber content) using jute fiber. The thermomechanical and morphological properties of the biocomposites were compared with jute‐PLA composites and a hybrid composite made of the impregnated jute fibers with n5 resin and PLA. SEM and DMA showed that the n5‐jute composites had better mechanical properties than the other composites produced. Inexpensive monomers, good thermomechanical properties and good processability of the n5 resin make the resin comparable with commercial unsaturated polyester resins. © 2017 Society of Chemical Industry     

Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) with high molecular weight poly(lactic acid) blends determined by thermal analysis

An important strategy used in the polymer industry in recent years is blending two bio‐based polymers to attain desirable properties similar to traditional thermoplastics, thus increasing the application potential for bio‐based and bio‐degradable polymers. Miscibility of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (PHBV) with poly(L ‐lactic acid) (PLA) were characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Three different grades of commercially available PLAs and one type of PHBV were blended in different ratios of 50/50, 60/40, 70/30, and 80/20 (PHBV/PLA) using a micro‐compounder at 175°C. The DSC and TGA analysis showed the blends were immiscible due to different stereo configuration of PLA polymer and two distinct melting temperatures. However, some compatibility between PHBV and PLA polymers was observed due to decreases in PLA's glass transition temperatures. Additionally, the blends do not show clear separation by SEM analysis, as observed in the thermal analysis. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Compatibility study of chlorinated polyethylene/ethylene methacrylate copolymer blends using thermal,mechanical, and chemical analysis

Blends of chlorinated polyethylene (CPE) elastomer and ethylene methacrylate copolymer (EMA) in various compositions were studied for their compatibility using differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), and Fourier transform infrared (FTIR) spectroscopy techniques. Irrespective of measurement techniques used, all blends showed a single glass transition temperature (T_g) lying in between the T_g of control polymers in both DSC and DMA. Glass transition temperatures of blends obtained from DSC were in consistency with Couchman–Karasz equation. Also, the T_g obtained from both DSC and DMA are above the “rule of mixing” line of the two control polymers. These results from thermal analysis clearly indicate some compatibility between the two polymers. Furthermore, compatibility of CPE/EMA blends were also been investigated by FTIR spectroscopy and scanning electron microscopic analysis. A shifting of characteristic C? Cl stretching peak of CPE and C?O stretching peak of EMA toward lower wave number indicate the presence of specific interaction between the two polymers. Mechanical properties like tensile strength, modulus at 100% elongation, elongation at break, and hardness were observed above the line of additivity drawn between the two control polymers, which corroborate compatibility between CPE and EMA. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40316.     

Compatible and crystallization properties of poly(lactic acid)/poly(butylene adipate‐co‐terephthalate) blends

Differential scanning calorimetry (DSC), wide angle X‐ray diffraction (WAXD) and dynamic mechanical analysis (DMA) properties of poly(lactic acid)/ poly(butylene adipate‐co‐terephthalate) (PLA/PBAT) specimens suggest that only small amounts of poor PLA and/or PBAT crystals are present in their corresponding melt crystallized specimens. In fact, the percentage crystallinity, peak melting temperature and onset re‐crystallization temperature values of PLA/PBAT specimens reduce gradually as their PBAT contents increase. However, the glass transition temperatures of PLA molecules found by DSC and DMA analysis reduce to the minimum value as the PBAT contents of PLA_xPBAT_y specimens reach 2.5 wt %. Further morphological and DMA analysis of PLA/PBAT specimens reveal that PBAT molecules are miscible with PLA molecules at PBAT contents equal to or less than 2.5 wt %, since no distinguished phase‐separated PBAT droplets and tan δ transitions were found on fracture surfaces and tan δ curves of PLA/PBAT specimens, respectively. In contrast to PLA, the PBAT specimen exhibits highly deformable properties. After blending proper amounts of PBAT in PLA, the inherent brittle deformation behavior of PLA was successfully improved. Possible reasons accounting for these interesting crystallization, compatible and tensile properties of PLA/PBAT specimens are proposed. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Ultraporous poly(lactic acid) scaffolds with improved mechanical performance using high‐pressure molding and salt leaching

A novel processing technique, i.e. high‐pressure compression molding/salt leaching, was developed to fabricate ultraporous poly(lactic acid) (PLA) scaffolds. The optimized composition was studied in relation to the porosity, pore morphology, thermal property, and mechanical performance of the PLA scaffolds. At a porogen (CaCO₃) content of 90 wt %, the scaffolds have an interconnected open pore structure and a porosity above 80%. It was truly interesting that the structural stability of high‐pressure molded scaffolds was remarkably improved based on the fact that its glass transition temperature (83.5°C) increased about 20°C, as compared to that of the conventional compression‐molded PLA (60°C), which is not far from physiological temperature (～37°C) at the risk of structural relaxation or physical aging. More importantly, the mechanical performance of PLA scaffolds was drastically enhanced under optimized processing conditions. At pressure and temperature of 1000 MPa and 190°C, the porous PLA scaffolds attained a storage modulus of 283.7 MPa, comparable to the high‐end value of trabecular bone (250 MPa) ever reported. In addition, our prepared PLA scaffolds showed excellent cellular compatibility and biocompatibility in vitro tests, further suggesting that the high‐pressure molded PLA scaffolds have high potential for bone tissue engineering applications. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3509–3520, 2013     

Morphology,mechanical properties,and durability of poly(lactic acid) plasticized with Di(isononyl) cyclohexane‐1,2‐dicarboxylate

Di(isononyl) cyclohexane‐1,2‐dicarboxylate (DINCH) was used as a new plasticizer for poly(lactic acid) (PLA), and the effects of DINCH and tributyl citrate ester (TBC) on the morphology, mechanical and thermal properties, and durability of PLA were compared. DINCH has limited compatibility with PLA, leading to PLA/DINCH blends with phase separation in which DINCH forms spherical dispersed phase. TBC is compatible with PLA and evenly distributed in PLA. Plasticized PLA with 10 and 20 phr DINCH have a constant glass transition temperature (T_g) of 50°C and are stiff materials with high elongation at break and impact strength. TBC could significantly decrease the T_g and increase the crystallinity of PLA, and PLA/TBC (100/20) blend is a soft material with a T_g of 24°C. The durability of plasticized PLA was characterized by weight loss measurement under water immersion, mechanical properties, and thermal analysis. The results reveal that PLA/DINCH blends have better water resistance and aging resistance properties than PLA/TBC blends, which is attributed to the relatively high hydrophobicity of DINCH and high T_g of PLA/DINCH blends. POLYM. ENG. SCI., 2009. © 2009 Society of Plastics Engineers     

Synthesis and properties of a novel bismaleimide resin containing 1,3,4‐oxadiazole moiety and the blend systems thereof with epoxy resin

A new bismaleimide monomer, 2‐((4‐maleimidophenoxy)methyl)‐5‐(4‐maleimidophenyl)‐1,3,4‐oxadiazole (Mioxd), was designed and synthesized. The chemical structure of the monomer was confirmed by means of Fourier transform infrared (FTIR) spectroscopy, proton nuclear magnetic resonance (¹H NMR) spectroscopy and elemental analysis, and its thermal properties were characterized using differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Mioxd as a reactive modifier was blended with epoxy resin based on bisphenol A diglycidyl ether (DGEBA) in weight ratio of 5, 10, and 15%, using 4,4′‐diaminodiphenyl sulfone (DDS) as hardener. The effect of Mioxd addition on the cure behavior and thermal properties of the blend resins was studied by DSC, TGA, and dynamic mechanical analysis (DMA). DSC investigations showed that the main exothermic peak temperature (T_p) of the blend systems did not obviously shift with increasing Mioxd content whereas a new shoulder appeared and gradually grew on the high temperature side of the exothermic peak. The results of DMA measurements exhibited the glassy storage modulus (G') and glass transition temperatures (T_g) increased as the Mioxd content was increased, the cured blends investigated were miscible and no phase separation occurred. Further, the thermal decomposition temperature first decreased and then increased, but the char yield at 600°C increased with an increase in Mioxd content. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Novel flame retardant thermosets from nitrogen‐containing and phosphorus‐containing epoxy resins cured with dicyandiamide

A novel phosphorus‐containing epoxy resin (EPN‐D) was prepared by addition reaction of 9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene 10‐oxide (DOPO) and epoxy phenol‐ formaldehyde novolac resin (EPN). The reaction was monitored by epoxide equivalent weight (EEW) titration, and its structure was confirmed by FTIR and NMR spectra. Halogen‐free epoxy resins containing EPN‐D resin and a nitrogen‐containing epoxy resin (XT resin) were cured with dicyandiamide (DICY) to give new halogen‐free epoxy thermosets. Thermal properties of these thermosets were studied by differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), thermal mechanical analyzer (TMA) and thermal‐gravimetric analysis (TGA). They exhibited very high glass transition temperatures (T_gs, 139–175°C from DSC, 138–155°C from TMA and 159–193°C from DMA), high thermal stability with T_{d,5 wt %} over 300°C when the weight ratio of XT/EPN‐D is ≥1. The flame‐retardancy of these thermosets was evaluated by limiting oxygen index (LOI) and UL‐94 vertical test. The thermosets containing isocyanurate and DOPO moieties showed high LOI (32.7–43.7) and could achieve UL‐94 V‐0/V‐1 grade. Isocyanurate and DOPO moieties had an obvious synergistic effect on the improvement of the flame retardancy. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Effect of different aromatic amines on the crosslinking behavior and thermal properties of phthalonitrile oligomer containing biphenyl ethernitrile

To find a proper amine to promote the processability of phthalonitrile‐based composites, three different aromatic amines: 4‐aminophenoxyphthalonitrile (APN), 2,6‐bis (4‐diaminobenzoxy) benzonitrile (BDB) and 4,4′‐diaminediphenyl sulfone (DDS) were used as curing agents to investigate the crosslinking behavior and thermal decomposition behavior of phthalonitrile oligomer containing biphenyl ethernitrile (2PEN‐BPh). Differential scanning calorimeter (DSC) and dynamic rheological analysis were employed to study the curing reaction behavior of the phthalonitrile/amine blends and prepolymers. The studies revealed that BDB was the preferred curing agent and the preferred concentration of BDB was 3 wt %. The thermal properties of the 2PEN‐BPh polymers were monitored by TGA, and the results indicated that all the completely cured 2PEN‐BPh polymers maintained good structure integrity upon heating to elevated temperatures and these polymers could thermal stabilize up to over 550°C in both air and nitrogen atmospheres. Dynamic mechanical analysis (DMA) showed the glass transition temperature (T_g) exceeded 450°C when the 2PEN‐BPh polymer post cured at 375°C for 8 h. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Comparison of thermal techniques for glass transition measurements of polystyrene and cross-linked acrylic polyurethane films

There are few quantitative comparisons in the literature between glass transitions (T_g) measured by differential scanning calorimetry (DSC) and by dynamic mechanical analysis (DMA). Also, in the case of DMA, two different operational definitions have been used to obtain the glass transition, namely, the loss modulus (E″) and damping (tan δ) peak temperatures. We propose a new DMA definition of T_g and demonstrate that it agrees with DSC T_g measurements within ±2°C for both thermoplastic polystyrene and thermoset cross-linked acrylic polyurethane films with measurable tan δ peaks. The glass transitions for a single polystyrene standard and several cross-linked acrylic polyurethane films were measured by DSC. Additionally, E″ and tan δ peak temperatures were measured by DMA as a function of frequency and temperature. Empirically, it was determined that the average of the E″ and tan δ peak temperatures measured at 1 rad/s oscillation frequency corresponds to the glass transition measured by the ASTM E1356 DSC test method. © 1994 John Wiley & Sons, Inc.     

Study on biodegradable polymer materials based on poly(lactic acid). I. Chain extending of low molecular weight poly(lactic acid) with methylenediphenyl diisocyanate

Methylenediphenyl diisocyanate (MDI) was used as the chain extender for low molecular weight poly(lactic acid) (PLA) to produce high molecular weight biodegradable polymer material with a better heat resistance. PLA prepolymer with a number‐average molecular weight (M_n) of 5800 and a weight‐average molecular weight (M_w) of 9800 was produced by direct polycondensation using stannous octoate as the catalyst. After 40 min of chain extension at 175°C, the resulting polymer had a M_n of 15,000 and a M_w of 57,000. The glass transition temperature (T_g) of the low molecular weight PLA prepolymer was 48.6°C. After chain extension, the T_g of the resulting polymer was raised to 67.9°C, as determined by DSC. DMA results also indicate that the heat resistance was improved by the chain extension. The DSC spectrum and X‐ray diffraction pattern of annealed samples showed that both the crystallinity and rate of crystallization of PLA were lowered by chain‐extension reaction due to the formation of branched molecular structure. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2546–2551, 1999     

Low dielectric thermoset. I. Synthesis and properties of novel 2,6‐dimethyl phenol‐dicyclopentadiene epoxy

A 2,6‐dimethyl phenol‐dicyclopentadiene novolac was synthesized from dicyclopentadiene and 2,6‐dimethyl phenol, and the resultant 2,6‐dimethyl phenol‐dicyclopentadiene novolac was epoxidized to 2,6‐dimethyl phenol‐dicyclopentadiene epoxy. The structures of novolac and epoxy were confirmed by Fourier transform infrared spectroscopy (FTIR), elemental analysis, mass spectroscopy (MS), nuclear magnetic resonance spectroscopy (NMR), and epoxy equivalent weight titration. The synthesized 2,6‐dimethyl phenol‐dicyclopentadiene epoxy was then cured with 4,4‐diaminodiphenyl methane (DDM), phenol novolac (PN), 4,4‐diaminodiphenyl sulfone (DDS), and 4,4‐diaminodiphenyl ether (DDE). Thermal properties of cured epoxy resins were studied by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA), dielectric analysis (DEA), and thermal gravimetric analysis (TGA). These data were compared with those of the commercial bisphenol A epoxy system. Compared with the bisphenol A epoxy system, the cured 2,6‐dimethyl phenol‐ dicyclopentadiene epoxy resins exhibited lower dielectric constants (～3.0 at 1 MHz and 2.8 at 1 GHz), dissipation factors (～0.007 at 1 MHz and 0.004 at 1 GHz), glass transition temperatures (140–188°C), thermal stability (5% degradation temperature at 382–404°C), thermal expansion coefficients [50–60 ppm/°C before glass‐transition temperature (T_g)], and moisture absorption (0.9–1.1%), but higher modulus (～2 Gpa at 60°C). © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2607–2613, 2003     

Effect of the molecular structure of polyurethane elastomers on the thermomechanical properties of PUE/PC blends

Polyurethane elastomers (PUEs) based on 4,4′‐diphenylmethane diisocyanate (MDI), 1,4‐butanediol (BDO) and two kinds of aliphatic polycaprolactone (PCL) diols with molecular weight of 1000 Da and 2000 Da have been synthesized and melt‐blended with polycarbonate (PC). The compatibility of PC and PUEs was investigated by differential scanning calorimetry (DSC), dynamic mechanical analysis (DMA) and scanning electron microscopy (SEM). The results indicated that the glass transition temperature (T_g) of PC decreased by 0–40°C when 0–10 wt % of PUEs incorporated into the PC matrix. Phase separation in the blends was not detected by means of DSC characterization, but measurements of DMA and SEM indicated that phase separation existed in the blends of PC and PUEs synthesized with 1000 Da PCL‐diol. As for PUEs/PC blend in which 2000 Da PCL‐diol as PUEs' soft segments, it turned from completely compatible to partially when the NCO/OH ratio for the PUEs prepolymer was increased from 2 : 1 to 4 : 1. The compatibilities of PC and PUEs were greatly influenced by the molecular weight of polyols and the ratio of NCO/OH in the PUE prepolymer, higher molecular weight of polyols and lower NCO/OH ratio resulted in better compatibility. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

New polymers from epoxidized soybean oil with pyridine derivatives

In this study 4‐methylpyridine (4MP), 4‐vinylpyridine (4VP) and poly(4‐vinylpyridine) (P4VP) were separately reacted with epoxidized soybean oil triglycerides (ESO) to give plant oil based thermoset polymers. The addition reaction of pyridine with epoxide followed by a rearrangement results in formation of pyridone units and these were polymerized via a Diels–Alder reaction. DMA, DSC, TGA and IR spectroscopy were used for the characterization of the products. 4MP‐ESO, P4VP‐ESO and P4VP‐ESO‐in situ polymers were crosslinked yielding rigid infusible polymers. Glass transition temperatures (T_g) of 4MP‐ESO and P4VP‐ESO‐in situ were found as ?10.5 and 70.5 (32.3 as shoulder) °C respectively, by DMA analysis. Storage moduli of 4MP‐ESO and P4VP‐ESO‐in situ at 25°C were 13.7 and 187.2 MPa, respectively. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of modified bismaleimide resins based on phthalide‐containing monomer

A series of bismaleimide resins based on phthalide‐containing monomer have been prepared by the copolymerization reaction of 3,3‐bis[4‐(4‐maleimidophenoxy)phenyl] ‐phthalide (PPBMI), 4, 4'‐dimaleimido diphenylmethane (MBMI) and 2, 2'‐diallyl bisphenol A (DABPA) in different feed ratios. The curing behavior, thermal, mechanical and physical properties and compatibility of all resultant resins were carefully characterized using differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), notched Izod impact test, water absorption test and scanning electron microscopy (SEM). DSC investigations showed that with an increase of the weight ratio of PPBMI, the dominating exothermic polymerization temperature (T_p) increased. The glass transitions were observed from DMA thermograms for the cured BMI resins in the temperature range from 277°C to 311°C and decreased with increasing PPBMI content. The TGA results indicated the thermal stability was improved as PPBMI content increased. The investigations of the mechanical properties showed a complicated trend with an increase in PPBMI content. In addition, the equilibrium water uptake of the modified resins was reduced as PPBMI content increased. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 1084‐1091, 2013     

Preparations and properties of a high performance semicrystalline copolyimide and composites reinforced with glass fiber

A semicrystalline copolyimide derived from 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (s‐BPDA), 1,3‐bis‐(4‐aminophenoxy)benzene (TPER), and 4,4′‐oxydianiline (4,4′‐ODA), end capped with phthalic anhydride (PA), was synthesized. Glass fiber reinforced composite was also prepared by impregnating powdery glass fiber with poly(amic acid) followed by solution imidization techniques. This copolyimide displayed a glass transition temperature of 202°C and a melting temperature of 373°C by differential scanning colorimeter (DSC). Crystallization and melting behaviors were investigated under nonisothermal and isothermal crystallization conditions. Double exothermic peaks were found by DSC when the copolyimide was cooled from the melt and multiple melting behaviors can be observed after the coployimide had been isothermally crystallized at different temperatures. Mechanical properties were investigated by dynamical mechanical analysis (DMA) and tensile experiments. The samples were cured at different temperatures and then tested at different temperatures. Results indicated that the copolyimide and the composite showed excellent mechanical properties. Additionally, this copolyimide also showed lower melt viscosity by rheological analysis. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40345.     

Phase segregation behavior in PE/DOP blends and glass‐transition temperatures of polyethylene

Phase segregation behavior in PEs/DOP blends, interactions between PEs and DOP, and glass‐relaxation transitions of PEs were investigated. FTIR, DSC, and TGA data demonstrated that molecular interactions were present between PEs and DOP. DMA data demonstrated that pure PEs each (except HDPE) exhibited two loss maxima at about ?20 and ?120°C but the PEs/DOP blends (including the HDPE/DOP blend) yielded one new loss maximum at about ?60°C. The glass‐relaxation transitions corresponding to the three loss maxima on the DMA curves were designated α (?20°C), β (?60°C), and γ (?120°C) transitions and were attributed to the relaxation of the amorphous phases in the interlamellar, interfibrillar, and interspherulitic regions, respectively, based on DMA, WAXD, SAXS, and POM measurements. The controversial T_g values of PEs and their origin were thus clarified in this study. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3591–3601, 2001     

Super-crosslinked ionic liquid-intercalated montmorillonite/epoxy nanocomposites: Cure kinetics,viscoelastic behavior and thermal degradation mechanism

Super-crosslinked epoxy nanocomposites containing N-octadecyl-N′-octadecyl imidazolium iodide (IM)-functionalized montmorillonite (MMT-IM) nanoplatelets were developed and examined for cure kinetics, viscoelastic behavior and thermal degradation kinetics. The structure and morphology of MMT-IM were characterized by FTIR, XRD, TEM, and TGA. Synthesized MMT-IM revealed synergistic effects on the network formation, the glass transition temperature (T_g) and thermal stability of epoxy. Cure and viscoelastic behaviors of epoxy nanocomposites containing 0.1 wt% MMT and MMT-IM were compared based on DSC and DMA, respectively. Activation energy profile as a function of the extent of cure was obtained. DMA results indicated a strong interface between imidazole groups of MMT-IM and epoxy, which caused a significant improvement in storage modulus and the T_g of epoxy. Network degradation kinetics of epoxy containing 0.5, 2.0, and 5.0 wt% MMT and MMT-IM were compared by using Friedman, Kissinger-Akahira-Sunose (KAS), Flynn-Wall-Ozawa (FWO) and the modified Coats-Redfern methods. Although addition of MMT to epoxy was detrimental to the T_g value, as featured by a fall from 94.1°C to 89.7°C detected by DMA method, and from 103.3°C to 97.9°C by DSC method, respectively. By contrast, meaningful increase in such values were observed in the same order from 94.1°C to 94.7°C and from 103.3°C to 104.7°C for super-crosslinked epoxy/MMT-IM systems.     

Morphology,biodegradability, mechanical,and thermal properties of nanocomposite films based on PLA and plasticized PLA

In this study, melt intercalation method is applied to prepare poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG)‐plasticized PLA nanocomposite films including 0, 3, and 5% organoclay (Cloisite 30B) using a laboratory scale compounder, which is connected to a microcast film device. To evaluate the nanomorphology and the dispersion state of the clays, X‐ray diffraction (XRD) and transmission electron microscopy (TEM) are conducted. Tensile tests are performed to characterize the mechanical behavior of the films. Biodegradation rate is determined by degradation tests in composting medium. Differential scanning calorimeter (DSC) is applied to observe the thermal behavior of the films. XRD and TEM show that the exfoliation predominantly occurrs in plasticized PLA nanocomposites, whereas unexfoliated agglomerates together with exfoliated clays are observed in the nonplasticized PLA. Tensile tests indicate that the addition of 3% clay to the neat‐PLA does not affect the strength; however, it enhances the modulus of the nanocomposites in comparison to neat‐PLA. Incorporation of 3% clay to the plasticized PLA improves the modulus with respect to PLA/PEG; on the other hand, the strain at break value is lowered ～ 40%. The increase in the rate of biodegradation in composting medium is found as in the order of PLA > PLA/PEG > 3% Clay/PLA/PEG > 5% Clay/PLA/PEG > 3% Clay/PLA. DSC analysis shows that the addition of 3% clay to the neat PLA results in an increase in T_g. The addition of 20% PEG as a plasticizer to the neat‐PLA decreases T_g about 30°C, however incorporation of clays increases T_g by 4°C for the plasticized PLA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Crystallization,morphology, and mechanical behavior of polylactide/poly(ε‐caprolactone) blends

Optically pure polylactides, poly(L ‐lactide) (PLLA) and poly(D ‐lactide) (PDLA), were blended across the range of compositions with poly(ε‐caprolactone) (PCL) to study their crystallization, morphology, and mechanical behavior. Differential scanning calorimetry and dynamic mechanical analysis (DMA) of the PLA/PCL blends showed two T_gs at positions close to the pure components revealing phase separation. However, a shift in the tan δ peak position by DMA from 64 to 57°C suggests a partial solubility of PCL in the PLA‐rich phase. Scanning electron microscopy reveals phase separation and a transition in the phase morphology from spherical to interconnected domains as the equimolar blend approaches from the outermost compositions. The spherulitic growth of both PLA and PCL in the blends was followed by polarized optical microscopy at 140 and 37°C. From tensile tests at speed of 50 mm/min Young's modulus values between 5.2 and 0.4 GPa, strength values between 56 and 12 MPa, and strain at break values between 1 and 400% were obtained varying the blend composition. The viscoelastic properties (E′ and tan δ) obtained at frequency of 1 Hz by DMA are discussed and are found consistent with composition, phase separation, and crystallization behavior of the blends. POLYM. ENG. SCI., 46:1299–1308, 2006. © 2006 Society of Plastics Engineers