Water vapor permeability of poly(lactide)s: Effects of molecular characteristics and crystallinity

Amorphous‐made poly(L ‐lactide) [i.e., poly(L ‐lactic acid) (PLLA)], poly(L ‐lactide‐co‐D ‐lactide)[P(LLA‐DLA)](77/23), and P(LLA‐DLA)(50/50) films and PLLA films with different crystallinity (X_c) values were prepared, and the effects of molecular weight, D ‐lactide unit content (tacticity and optical purity), and crystallinity of poly(lactide) [i.e., poly(lactic acid) (PLA)] on the water vapor permeability was investigated. The changes in number‐average molecular weight (M_n) of PLLA films in the range of 9 × 10⁴–5 × 10⁵ g mol^?1 and D ‐lactide unit content of PLA films in the range of 0–50% have insignificant effects on their water vapor transmission rate (WVTR). In contrast, the WVTR of PLLA films decreased monotonically with increasing X_c from 0 to 20%, while leveled off for X_c exceeding 30%. This is probably due to the higher resistance of “restricted” amorphous regions to water vapor permeation compared with that of the “free” amorphous regions. The free and restricted amorphous regions are major amorphous components of PLLA films for X_c ranges of 0–20% and exceeding 30%, respectively, resulting in the aforementioned dependence of WVTR on X_c. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Highly enhanced accelerating effect of melt‐recrystallized stereocomplex crystallites on poly(L‐lactic acid) crystallization: effects of molecular weight of poly(D‐lactic acid)

The effects of the molecular weight of poly(D ‐lactic acid) (PDLA), which forms stereocomplex (SC) crystallites with poly(L ‐lactic acid) (PLLA), and those of processing temperature T_p on the acceleration (or nucleation) of PLLA homocrystallization were investigated using PLLA films containing 10 wt% PDLA with number‐average molecular weight (M_n) values of 5.47 × 10⁵, 9.67 × 10⁴ and 3.67 × 10⁴ g mol^–1 (PDLA‐H, PDLA‐M and PDLA‐L, respectively). For the PLLA/PDLA‐H and PLLA/PDLA‐M films, the SC crystallites that were ‘non’‐melted and those that were ‘completely’ melted at T_p values just above their endset melting temperature and recrystallized during cooling were found to act as effective accelerating (or nucleation) agents for PLLA homocrystallization. In contrast, SC crystallites formed from PDLA‐L, having the lowest M_n, were effective accelerating agents without any restrictions on T_p. In this case, the accelerating effects can be attributed to the plasticizer effect of PDLA‐L with the lowest M_n. The accelerating effects of SC crystallites in the PLLA/PDLA‐H and PLLA/PDLA‐M films was dependent on crystalline thickness for T_p values below the melting peak temperature of SC crystallites, whereas for T_p values above the melting peak temperature the accelerating effects are suggested to be affected by the interaction between the SC crystalline regions and PLLA amorphous regions.     

Synthesis and characterization of star‐shaped poly(ethylene glycol)‐block‐poly(L‐lactic acid) copolymers by melt polycondensation

Compared with linear diblock or triblock poly(ethylene glycol)‐block‐poly(L ‐lactic acid) copolymer (PEG‐b‐PLLA), star‐shaped PEG‐b‐PLLA (sPEG‐b‐PLLA) copolymers exhibit smaller hydrodynamic radius and lower viscosity and are expected to display peculiar morphologies, thermal properties, and degradation profiles. Compared with the synthesis routine of PEG‐b‐PLLA form lactide and PEG, the traditional synthesis routine from LA and PEG were suffered by the low reaction efficiency, low purity, lower molecular weight, and wide molecular weight distribution. In this article, multiarm sPEG‐b‐PLLA copolymer was prepared from multiarm sPEG and L ‐lactic acid (LLA using an improved method of melt polycondensation, in which two types of sPEG, that is, sPEG₁ (four arm, Mn = 4300) and sPEG₂ (three arm, Mn = 3200) were chosen as the core. It was found the molecular weight of sPEG‐b‐PLLA could be strongly affected by the purity of LLA and sPEGs, and the purification technology of vacuum dewater and vacuum distillation could help to remove most of the impurities in commercial available LLA. The polymers, including sPEG and sPEG‐b‐PLLA with varied core (sPEG₁ and sPEG₂) and LLA/sPEG feeding ratios, were characterized and confirmed by ¹H‐NMR and ¹³C‐NMR spectroscopy, Fourier transform infrared spectroscopy (FT‐IR) and gel permeation chromatography, which showed that the terminal hydroxyl group in each arm of sPEGs had reacted with LLA to form sPEG‐b‐PLLA copolymers with fairly narrow molecular weight distribution. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Hydrolytic Degradation of Amorphous Films of L‐Lactide Copolymers with Glycolide and D‐Lactide

Summary: Films of poly(L ‐lactic acid) (PLLA) and copolymers of L ‐lactide (LLA) with either glycolide [P(LLA‐GA)](81/19) or D ‐lactide [P(LLA‐DLA)](77/23) were prepared and an effect of comonomer type on the hydrolytic degradation of the films was studied in phosphate‐buffered solutions at 37 °C. The degraded films were investigated using gravimetry (weight loss and water absorption), gel permeation chromatography, DSC, X‐ray diffractometry, tensile testing and polarization optical microscopy. To exclude the effects of molecular weight and crystallinity on hydrolytic degradation, the films were prepared from polymers with similar molecular weights and were made amorphous by melt quenching. It was found that the hydrolytic degradation rate decreased in the order P(LLA‐GA) > P(LLA‐DLA) > PLLA. The hydrolytic degradation rate constant of PLLA and LLA copolymer films increased with increasing the water absorption (hydrophilicity), or with decreasing the initial glass transition temperature or the L ‐lactyl unit sequence length, indicating that the hydrolytic degradation rate of the copolymers was closely related to these three parameters. The crystallization of P(LLA‐GA) film occurred within hydrolytic degradation for 20 weeks.

M_n of PLLA and LLA copolymer films as a function of hydrolytic degradation time.     

Synthesis and structure control of l‐lactic acid–glycolic acid copolymer by homo‐copolymerization

A two‐step direct melt copolymerization process of l ‐lactic acid (L ‐LA)/glycolic acid (GA) was developed: poly(l ‐lactic acid) (PLLA) and poly(glycolic acid) (PGA) with different molecular weight was first synthesized respectively by binary catalyst (tin chloride/p‐toluenesulfonic or tin chloride); and then poly(l ‐lactic‐co‐glycolic acid) (b‐PLGA) was produced by melt polymerization of the as‐prepared PLLA and PGA, wherein the composition and chain structure of b‐PLGA copolymers could be controlled by the molecular weight of PLLA. The chain structure and thermal properties of copolymers were studied by Wide‐angle X‐ray diffraction, nuclear magnetic resonance, differential scanning calorimetry, and thermogravimetric analysis. In comparison with the random PLGA (r‐PLGA) synthesized by one‐step direct melt polymerization, the average l ‐lactic blocks length (L_LA) in b‐PLGA was longer while the average glycolic blocks length (L_GA) in b‐PLGA was shorter which further resulted in the improved crystallinity and thermostability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41566.     

Synthesis and thermal properties of poly(methyl methacrylate)‐poly(L‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer

Poly(methyl methacrylate)‐poly(L ‐lactic acid)‐poly(methyl methacrylate) tri‐block copolymer was prepared using atom transfer radical polymerization (ATRP). The structure and properties of the copolymer were analyzed using infrared spectroscopy, gel permeation chromatography, nuclear magnetic resonance (¹H‐NMR, ¹³C‐NMR), thermogravimetry, and differential scanning calorimetry. The kinetic plot for the ATRP of methyl methacrylate using poly(L ‐lactic acid) (PLLA) as the initiator shows that the reaction time increases linearly with ln[M]₀/[M]. The results indicate that it is possible to achieve grafted chains with well‐defined molecular weights, and block copolymers with narrowed molecular weight distributions. The thermal stability of PLLA is improved by copolymerization. A new wash‐extraction method for removing copper from the ATRP has also exhibits satisfactory results. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and chain extension of poly(L‐lactic acid‐co‐succinic acid‐co‐1,4‐butene diol)

L ‐Lactic acid (LA) was copolymerized with succinic acid (SA) and 1,4‐butenediol (1,4‐BED) in bulk state with titanium(IV) butoxide as a catalyst to produce poly(LA‐co‐SA‐co‐1,4‐BED) (PLASBED). Poly(L ‐lactic acid) (PLLA) homopolymer obtained from a direct condensation polymerization of LA had weight average molecular weight (M_w) less than 4.1 × 10⁴ and was too brittle to prepare specimens for the tensile test. Addition of SA and 1,4‐BED to LA produced PLASB with M_w as high as 1.4 × 10⁵ and exhibited tensile properties comparable to a commercially available high‐molecular‐weight PLLA. Chain extension by intermolecular linking reaction through the unsaturated 1,4‐BED units in PLASBED with benzoyl peroxide further increased the molecular weight and made PLASBED more ductile and flexible to show elongation at break as high as 450%. Biodegradability of PLASBED measured by the modified Sturm test was nearly independent of the 1,4‐BED content. Gel formation during the chain extension did not exert any significant influence on the biodegradability either. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1116–1121, 2005     

Synthesis of high molecular weight poly(L‐lactic acid) via melt/solid polycondensation: Intensification of dehydration and oligomerization during melt polycondensation

Melt/solid state polycondensation (MP/SSP) is a cost‐effective route for synthesis of high molecular weight poly(L ‐lactic acid) (PLLA). However, the reaction rates in its four stages need to be enhanced greatly and the reaction times to be shortened largely before the MP/SSP technology can be industrialized. In this study, a new catalyst addition policy, i.e., adding TSA at the dehydration stage and SnCl₂·2H₂O at the MP stage, and more appropriate temperature and pressure programs were presented and applied in the MP process of LLA. The presence of TSA from dehydration appeared very effective for speeding up the dehydration and oligomerization stages as well as depressing racemization in the whole MP process. The polymerization degree (X_n) of oligomer was clearly increased, and the reaction time was shortened to a great extent. Direct using reduced pressure was also very helpful for intensifying the dehydration stage, only leading to LLA loss as little as 2%. A PLLA with M_w of 44,000 and optical purity of 96.8% suitable for subsequent SSP was produced after dehydration for 2 h, oligomerization for 2 h and MP for 4 h under appropriate conditions. And an interesting strong dependence of the M_w of final PLLA product on the X_n of the oligomer was observed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Stereocomplex formation between poly(L‐lactic acid) and poly(D‐lactic acid) with disproportionately low and high molecular weights from the melt

Poly(L ‐lactic acid) (PLLA) and poly(D ‐lactic acid) (PDLA) with very different weight‐average molecular weights (M_w) of 4.0 × 10³ and 7.0 × 10⁵ g mol^?1 (M_w(PDLA)/M_w(PLLA) = 175) were blended at different PDLA weight ratios (X_D = PDLA weight/blend weight) and their crystallization from the melt was investigated. The presence of low molecular weight PLLA facilitated the stereocomplexation and thereby lowered the cold crystallization temperature (T_cc) for non‐isothermal crystallization during heating and elevated the radial growth rate of spherulites (G) for isothermal crystallization, irrespective of X_D. The orientation of lamellae in the spherulites was higher for the neat PLLA, PDLA and an equimolar blend than for the non‐equimolar blends. It was found that the orientation of lamellae in the blends was maintained by the stereocomplex (SC) crystallites. Although the G values are expected to decrease with an increase in X_D or the content of high‐molecular‐weight PDLA with lower chain mobility compared with that of low‐molecular‐weight PLLA, G was highest at X_D = 0.5 where the maximum amount of SC crystallites was formed and the G values were very similar for X_D = 0.4 and X_D = 0.6 with the same enantiomeric excess. This means that the effect of SC crystallites overwhelmed that of chain mobility. The nucleating mechanisms of SC crystallites were identical for X_D = 0.1–0.5 in the T_c range 130–180 °C. Copyright © 2011 Society of Chemical Industry     

Preparation of high‐molecular‐weight poly(L‐lactic acid)‐based polymers through direct condensation polymerization in bulk state

Poly(L ‐lactic acid‐co‐succinic acid‐co‐1,4‐butanediol) (PLASB) was synthesized by a direct condensation copolymerization of L ‐lactic acid, succinic acid (SA), and 1,4‐butanediol (BD) in bulk state using titanium(IV) butoxide (TNBT) as a catalyst. Weight average molecular weight (M_w) of PLASB increased from 3.5 × 10⁴ to 2.1 × 10⁵ as the content of SA and BD went up from 0.01 to 0.5 mol/100 mol of L ‐lactic acid (LA). PLASB having M_w in the range from 1.8 × 10⁵ to 2.1 × 10⁵ showed tensile properties comparable to those of commercially available poly(L ‐lactic acid) (PLLA). In sharp contrast, homopolymerization of LA in bulk state produced PLLA with M_w as low as 4.1 × 10⁴, and it was too brittle to prepare specimens for the tensile tests. M_w of PLASB synthesized by using titanium(IV)‐2‐ethyl(hexoxide), indium acetate, indium hydroxide, antimony acetate, antimony trioxide, dibutyl tin oxide, and stannous‐2‐ethyl 1‐hexanoate was compared with that of PLASB obtained by TNBT. Ethylene glycol oligomers with different chain length were added to LA/SA in place of BD to investigate effect of chain length of ethylene glycol oligomers on the M_w of the resulting copolymers. Biodegradability of PLASB was analyzed by using the modified Sturm test. Toxicity of PLASB was evaluated by counting viable cell number of mouse fibroblast cells that had been in contact with PLASB discs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 466–472, 2006     

A comprehensive single‐particle model for solid‐state polymerization of poly(L‐lactic acid)

We propose here, a comprehensive model for the solid‐state polymerization (SSP) of a low to moderate molecular weight (MW) prepolymer of lactic acid, to produce high MW poly(L ‐lactic acid) (PLLA). The reactions are rationally assumed to occur only in the amorphous region, and effective concentrations of end groups, vary with crystalinity, X_c, during SSP. We estimate byproduct diffusivities, D, using free volume theory. The effects of various parameters on the SSP of PLLA prepolymer have been examined with respect to the optimum MW, X_c and D. We introduce self‐consistently, scaling factors of ～ 0.27, in the experimental procedure, to determine via ¹⁹F‐NMR, concentrations of the end groups, after converting them to fluorinated ester groups. The relevant reaction rate constants are obtained by fitting to early time data from representative SSP experiments at 150°C, under high vacuum, on PLLA prepolymer powder (i.e., spherical geometry) of number average MW, M_n0 ～ 10,200 Da, which attains M_n ～ 150,000 Da, via SSP. The subsequent successful comparison of the model predictions with experimental data throughout the entire SSP duration indicates that the model is comprehensive and accounts for all the relevant phenomena occurring during the SSP to synthesize high MW PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis,physical properties,and crystallization of optically active poly(L‐phenyllactic acid) and poly(L‐phenyllactic acid‐co‐L‐lactic acid)

Optically active poly(L ‐phenyllactic acid) (Ph‐PLLA), poly(L ‐lactic acid) (PLLA), and poly(L ‐phenyllactic acid‐co‐L ‐lactic acid) with weight‐average molecular weight exceeding 6 × 10³ g mol^?1 were successfully synthesized by acid catalyzed direct polycondensation of L ‐phenyllactic acid and/or L ‐lactic acid in the presence of 2.5–10 wt % of p‐toluenesulfonic acid. Their physical properties and crystallization behavior were investigated by differential scanning calorimetry, thermogravimetry, and polarimetry. The absolute value of specific optical rotation ([α]) for Ph‐PLLA (?38 deg dm^?1 g^?1 cm³) was much lower than that of [α] for PLLA (?150 deg dm^?1 g^?1 cm³), suggesting that the helical nature was reduced by incorporation of bulky phenyl group. PLLA was crystallizable during solvent evaporation, heating from room temperature, and cooling from the melt. Incorporation of a very low content of bulky phenyllactyl units even at 4 mol % suppressed the crystallization of L ‐lactyl unit sequences during heating and cooling, though the copolymers were crystallizable for L ‐phenylactyl units up to 6 mol % during solvent evaporation. The activation energy of thermal degradation (ΔE_td) for Ph‐PLLA (200 kJ mol^?1) was higher than that for PLLA (158 kJ mol^?1). The ΔE_td for the copolymers increased with an increase in L ‐phenyllactyl unit content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of high‐molecular‐weight poly(l‐lactic acid) by chain‐extending reaction with phosphites

Poly(l ‐lactic acid) (PLLA) of high molecular weight was prepared by a chain‐extending reaction in a microcompounder. Phosphites were used as chain extenders to increase the molecular weight of the PLLA prepolymer, which was prepared by the bulk polycondensation of l‐lactic acid. The effects of the amount of phosphite, the temperature, and the screw speed on the torque of the PLLA melt were studied. Under the optimal conditions, the molecular weight of PLLA increased from 62,100 to 126,000 g/mol. The chemical structure and crystallinity of PLLA were characterized by Fourier transform infrared spectroscopy, ¹H‐NMR and ¹³C‐NMR, differential scanning calorimetry, and X‐ray diffraction. The mechanical properties of PLLA were measured. The results indicate that triphenyl phosphite (TPPi) was an effective chain extender for PLLA. The role of the TPPi in chain extending is suggested to be an esterification‐promotion agent. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Thermally induced crystallization and enzymatic degradation studies of poly (L‐lactic acid) films

Poly(L ‐lactic acid) (PLLA) films with different crystallinities were prepared by solvent casting and subsequently annealed at various temperatures (T_a) (80–110°C). The effects of crystallinity on enzymatic degradation of PLLA films were examined in the presence of proteinase K at 37°C by means of weight loss, DSC, FTIR spectroscopy, and optical microscopy. DSC and the absorbance ratio of 921 and 956 cm^?1 (A₉₂₁/A₉₅₆) were used to evaluate crystallinity changes during thermally induced crystallization and enzymatic hydrolysis. The highest percentage of weight loss was observed for the film with the lowest initial crystallinity and the lowest percentage of weight loss was observed for the film with highest crystallinity. FTIR investigation of degraded films showed a band at 922 cm^?1 and no band at 908 cm^?1 suggested that all degraded samples form α crystals. The rate of degradation was found to depend on the initial crystallinity of PLLA film and shown that enzymatic degradation kinetics followed first‐order kinetics for a given enzyme concentration. DSC crystallinity and IR absorbance ratio, A₉₂₁/A₉₅₆ ratio, showed no significant changes with degradation time for annealed PLLA films whereas as‐cast PLLA film showed an increase in crystallinity with degradation; this revealed that degradation takes place predominantly in the free amorphous region of annealed PLLA films without changing long range and short range order © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Non‐isothermal crystallization behavior of stereo diblock polylactides with relatively short poly(d‐lactide) segments from the melt

Stereo diblock polylactides (SDB‐PLAs) composed of relatively short poly(d ‐lactide) (PDLA) segments and relatively long poly(l ‐lactide) (PLLA) segments were synthesized to have a wide number‐average molecular weight (M_n) range of 2.5 × 10⁴–2.0 × 10⁵ g mol^?1 and d ‐lactyl unit content of 0.9–38.6%. The effects of incorporated short PDLA segments (M_n = 2.0 × 10³–7.7 × 10³ g mol^?1) on crystallization behavior of the SDB‐PLAs were first investigated during heating after complete melting and quenching or during slow cooling after complete melting. Stereocomplex (SC) crystallites can be formed at d ‐lactyl unit content as low as 4.3 and 5.8% for heating and slow cooling, respectively, and for M_n of PDLA segments as low as 2.0 × 10³ and 3.5 × 10³ g mol^?1, respectively. With decreasing M_n and increasing d ‐lactyl unit content, the cold crystallization temperature during heating decreased and the crystallization temperature during slow cooling increased. With increasing d ‐lactyl unit content, the melting enthalpy (ΔH_m) of SC crystallites during heating and the crystallinity (X_c) of SC crystallites after slow cooling increased, whereas ΔH_m of PLLA homo‐crystallites during heating and X_c of PLLA homo‐crystallites after slow cooling decreased. The total ΔH_m of SC crystallites and PLLA homo‐crystallites during heating and the total X_c after slow cooling became a minimum at d ‐lactyl unit content of 10–15% and gave a maximum at d ‐lactyl unit content of 0%. Despite the accelerated crystallization of some of SDB‐PLAs, the low values of total ΔH_m and X_c at d ‐lactyl unit content of 10–15% are attributable to the formation of two crystalline species of SC crystallites and PLLA homo‐crystallites.     

Spontaneous formation of polylactide stereocomplex microspheres containing metal ions

Linear poly(l ‐lactides) (PLLAs ) and poly(d ‐lactides) (PDLAs ) with M _n in the range 2000 ? 4300 containing a different number and placement of carboxyl groups were obtained via cationic ring‐opening polymerization and post‐polymerization functionalization. PLA stereoisomers (PLLA ‐(COOH )_x and PDLA ‐(COOH )_x , where x = 1 ? 3) were used for the investigation of stereocomplexation in solution performed in the presence of metal cations such as Ca²⁺, Mg²⁺, Zn²⁺, Fe³⁺. Spherical microparticles with a diameter in the range 0.7 ? 3.0 µm were obtained in all cases which was confirmed on the basis of scanning electron microscopy (SEM ) analysis. The microsphere size and homogeneity were analyzed depending on the stereocomplexation conditions and the molecular weight as well as the number of carboxyl end groups in the PLLA and PDLA used for stereocomplexation. The PLA microspheres obtained were analyzed by Fourier transform IR spectroscopy, wide angle X‐ray spectroscopy and energy‐dispersive X‐ray spectroscopy methods which confirmed the presence of metal cations inside. The application of regular microspheres with metal ions as drug delivery systems is considered. © 2016 Society of Chemical Industry     

Syntheses of poly(lactic acid)‐poly(ethylene glycol) serial biodegradable polymer materials via direct melt polycondensation and their characterization

Directly starting from lactic acid (LA) and poly(ethylene glycol) (PEG), biodegradable material polylactic acid‐polyethylene glycol (PLEG) was synthesized via melt copolycondensation. The optimal synthetic conditions, including prepolymerization method, catalyst kinds and quantity, copolymerization temperature and time, LA stereochemical configuration, feed weight ratio m_LA/m_PEG and M_n of PEG, were all discussed in detail. When D ,L ‐LA and PEG (M_n = 1000 Da) prepolymerized together as feed weight ratio m_{D ,l‐LA}/m_PEG = 90/10, 15 h copolycondensation under 165°C and 70 Pa, and 0.5 wt % SnO as catalyst, gave D ,L ‐PLEG1000 with the highest [η] of 0.40 dL/g, and the corresponding MW was 41,700 Da. Using L ‐LA instead of D ,L ‐LA, 10 h polymerization under 165°C and 70 Pa, and 0.5 wt % SnO as catalyst, gave L ‐PLEG1000 with the highest [η] of 0.21 dL/g and MW of 15,600 Da. Serial D ,L ‐PLEG with different feed weight ratio and M_n of PEG were synthesized via the simple and practical direct melt copolycondensation, and characterized with FTIR, ¹H NMR, GPC, DSC, XRD, and contact angle testing. D ,L ‐PELG not only had higher MW than PDLLA, PLLA and L ‐PELG, but also better hydrophilicity than PDLLA. The novel one‐step method could be an alternative route to the synthesis of hydrophilic drug delivery carrier PLEG instead of the traditional two‐step method using lactide as intermediate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 577–587, 2006     

Synthesis and characterization of poly(L‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(L‐lactic acid) copolyesters

Random copolyester namely, poly(ethylene terephthalate‐co‐sebacate) (PETS), with relatively lower molecular weight was first synthesized, and then it was used as a macromonomer to initiate ring‐opening polymerization of l ‐lactide. ¹H NMR quantified composition and structure of triblock copolyesters [poly(l ‐lactic acid)‐b‐poly(ethylene terephthalate‐co‐sebacate)‐b‐poly(l ‐lactic acid)] (PLLA‐PETS‐PLLA). Molecular weights of copolyesters were also estimated from NMR spectra, and confirmed by GPC. Copolyesters exhibited different solubilities according to the actual content of PLLA units in the main chain. Copolymerization effected melting behaviors significantly because of the incorporation of PETS and PLLA blocks. Crystalline morphology showed a special pattern for specimen with certain composition. It was obvious that copolyesters with more content of aromatic units of PET exhibited increased values in both of stress and modulus in tensile test. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Morphology and hydrolysis of PCL/PLLA blends compatibilized with P(LLA‐co‐ϵCL) or P(LLA‐b‐ϵCL)

The effect of the compatibilizers, P(LLA‐co‐?CL) and P(LLA‐b‐?CL), on the morphology and hydrolysis of the blend of poly(?‐caprolactone) (PCL) and poly(L ‐lactide) (PLLA) was investigated. An addition of P(LLA‐co‐?CL) or P(LLA‐b‐?CL) into the blend could enhance the compatibility between the dispersed PCL domains and the PLLA matrix. The size of the PCL domains in the PLLA/PCL (70/30) blend containing P(LLA‐co‐?CL) reduced more significantly with an increase in the content of the compatibilizer than that in the blend containing P(LLA‐b‐?CL). The molecular weight of the PLLA/PCL blend films compatibilized with P(LLA‐co‐?CL) or P(LLA‐b‐?CL) decreased during the hydrolysis and the decrease of the molecular weight of the blend films compatibilized with P(LLA‐co‐?CL) was much more significant than that of the blend films compatibilized with P(LLA‐b‐?CL). © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1892–1898, 2002     

Fabrication and in vitro investigation of nanohydroxyapatite,chitosan, poly(L‐lactic acid) ternary biocomposite

The nanohydroxyapatite/chitosan/poly(L ‐lactic acid) (HA/CS/PLLA) ternary biocomposites were prepared by blending the hydroxyapatite/chitosan (HA/CS) nanocomposites with poly(L ‐lactic acid) (PLLA) solution. Surface modification by grafting D ‐, L ‐lactic acid onto the HA/CS nanocomposites was designed to improve the bonding with PLLA. The FTIR and ¹³C‐NMR spectrum confirmed that the oligo(lactic acid) was successfully grafted onto the HA/CS nanocomposites, and the time‐dependent phase monitoring showed that the grafted copolymers were stable. The TEM morphology of the HA/CS/PLLA ternary nanocomposites showed that nano‐HA fibers were distributed homogeneously, compacted closely and wrapped tightly by the CS and PLLA matrix. The ternary biocomposites with the HA content of 60 and 67 wt % exhibited high compressive strength of about 160 MPa and suitable hydrophilicity. The in vitro tests exhibited that the ternary biocomposites have good biodegradability and bioactivity when immersed in SBF solutions. All the results suggested that the n‐HA/CS/PLLA ternary biocomposites are appropriate to application as bone substitute in bone tissue engineering. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013