Synthesis and characterization of poly(dimethylsiloxane)–polythiophene composites

The synthesis was performed by the electropolymerization of thiophene on a poly(dimethylsiloxane) (PDMS)‐coated platinum electrode at 2.2 V with tetrabutylammoniumtetrafloroborate (TBAFB) as a supporting electrolyte and with acetonitrile as a solvent. The characterization of the PDMS–polythiophene (Pth) composites was carried out with cyclic voltammetry, Fourier transform infrared (FTIR), scanning electron microscopy (SEM), differential scanning calorimetry (DSC), thermogravimetric analysis, and conductivity measurements. The observed conductivities of the PDMS composites were 2.2–5.2 S/cm. The conductivity of Pth did not change appreciably with the addition of up to 30% insulating PDMS, but its processability improved. FTIR, SEM, and DSC studies showed the existence of a strong interaction, rather than physical adhesion, between PDMS and Pth. Highly flexible and foldable PDMS–Pth composites were obtained. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 2113–2119, 2003     

Preparation and characterization of poly(glycerol sebacate)/cellulose nanocrystals elastomeric composites

Poly(glycerol sebacate) (PGS) is one of the new elastomers used for soft tissue engineering, while improving its limited mechanical strength is the biggest challenge. In this work, a novel biodegradable elastomer composite PGS/cellulose nanocrystals (CNCs) was prepared by solution‐casting method and the mechanical properties, sol–gel contents, crosslink density, and hydrophilic performance were characterized. The thermal and degradation properties of composites were also investigated. Results show that the addition of CNCs into PGS resulted a significant improvement in tensile strength and modulus, as well as the crosslink density and the hydrophilicity of PGS. When the CNCs loading reached 4 wt %, the tensile strength and modulus of the composite reached 1.5 MPa and 1.9 MPa, respectively, resulting 204% and 158% increase compared to the pure PGS. Prolonging the curing time also improved the strength of both the neat PGS and PGS/CNCs composites according to the association and shift of hydroxy peaks around 3480 cm^?1. DSC results indicate that the addition of CNCs improved both the crystallization capacity and moving capability of PGS molecular chain. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42196.     

Synthesis and characterization of poly(methyl methacrylate)/polysiloxane composites and their coating properties

A series of poly(methyl methacrylate) (PMMA)/polysiloxane composites and their coatings were prepared as designed. A copolymer (PMMAVTEOS) containing methyl methacrylate (MMA) and vinyltriethoxysilane (VTEOS) was prepared by free radical polymerization and then condensed with methyl triethoxysilane (MTES) to fabricate PMMA/polysiloxane composites; their corresponding coatings were obtained via a curing process in an oven (at 75 °C). The polymers were characterized by gel permeation chromatography and Fourier transform infrared spectroscopy. The surface property, hardness, water contact angle, thermal stability, and optical property of the coatings were investigated by scanning electron microscopy, pencil hardness testing, water contact angle testing, thermogravimetric analysis, and ultraviolet–visible spectroscopy, respectively. The results showed that, after addition of MMA, the pencil hardness of the coatings was reduced from 6H to 2H and the thermal stability decreased from 365 to 314 °C. However, it increased the flexibility and adhesion properties (the water contact angle increased from 94.7° to 102.1°). The transparent PMMA/polysiloxane coatings showed excellent scratch resistance, a smooth surface, high thermal stability, and a strong adhesion property. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46358.     

Synthesis and characterization of novel polyfuran/poly(2‐iodoaniline) conducting composite

The electrically conducting polyfuran/poly(2‐iodoaniline) (PFu/P2IAn) and P2IAn/PFu composites were prepared by chemical oxidative polymerization using polyfuran and poly(2‐iodoaniline) in HCl and CHCl₃ media. The conductivities of composites were determined as a function of the amount of guest polymer. It was found out that the conductivities of P2IAn/PFu composites increased 100‐fold, whereas the conductivities of PFu/P2IAn composites did not show a specific increase. The composite compositions were altered by varying guest polymer feed ratios during preparation. Generally, the electrical conductivities of P2IAn/PFu composites increased with increasing the amount of PFu. Homopolymers and composites were further characterized thermally, employing thermogravimetry (TGA) and morphologically employing scanning electron microscopy (SEM). Further evidences concerning the polymer structures were obtained by FTIR and UV‐vis spectroscopies and magnetic susceptibility measurements. TGA results revealed that PFu/P2IAn among the homopolymers (PFu and P2IAn) and P2IAn/PFu composite have the highest thermal stability. The composites synthesized varying the host and the guest polymer order have different conductivities, morphological structures, and thermal properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2823–2830, 2003     

Electrical properties of poly(phenylene sulfide)/multiwalled carbon nanotube composites prepared by simple mixing and compression

Poly(phenylene sulfide) (PPS)/multiwalled carbon nanotubes (MWNTs) conductive composites were prepared through the simple mixing of PPS granules with MWNT powder and subsequent compression. The electrical properties as a function of MWNT loading clearly showed a low percolation threshold of about 0.22 vol % and a high critical exponent value of 3.55 for composites prepared by this method. A comparison study with composites prepared via melt mixing was also carried out, where a random dispersion of MWNTs was achieved. There existed a striplike morphology of MWNTs in the PPS matrix and MWNTs were selectively located in strips caused by compression. The effects of temperature and pressure on the conductivity of the PPS/MWNT composites as prepared via simple mixing and compression are discussed. In addition, the conductivity also showed a dependence on the flow direction of the compression, with higher conductivity in the direction parallel to the flow direction than in the direction perpendicular to the flow direction. So the relationship of the processing and morphological properties was investigated in detail. The possible conductive mechanisms of conventional melt blending and preparation via sample mixing and compression are also discussed. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Ultrasonic characterization of conductive epoxy resin/polyaniline composites

This study presents the ultrasonic characterization of conductive epoxy resin (ER)/polyaniline (PANI) composites. The prepared PANI is mixed with ER matrix at weight percentages of 5%, 10%, and 15% for preparing the ER/PANI composites. The effects of PANI amount on the mechanical properties of ER/PANI composites are investigated by ultrasonic pulse‐echo‐overlap method. Also, electrical conductivity, ultrasonic wave velocity and ultrasonic micro‐hardness values of ER/PANI composites are correlated. Experimental results show that there is an excellent correlation between ultrasonic micro‐hardness and ultrasonic shear wave velocity. Also, the results of ultrasonic velocities and elastic constants values illustrate that the appropriate combination ratio is 95 : 5 for ER and PANI in ER/PANI composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42748.     

Preparation,characterization, electrical and antibacterial properties of sericin/poly(vinyl alcohol)/poly(vinyl pyrrolidone) composites

In this study, we focused on the fabrication of poly(vinyl alcohol) (PVA)/poly(vinyl pyrrolidone) (PVP)/sericin composites via a simple solution‐blending method. The composites were characterized by Fourier transform infrared (FTIR) spectroscopy, UV spectroscopy, X‐ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning calorimetry, thermogravimetric analysis (TGA), and measurements of the conductivity, tensile strength, and antibacterial activity against Staphylococcus aureus. The results of FTIR and UV spectroscopy implied the occurrence of hydrogen bonding between sericin and the PVA/PVP blend. The structure and morphology, studied by XRD and SEM, revealed that the sericin particles were well dispersed and arranged in an orderly fashion in the blend. The glass‐transition temperature (T_g) of the composite was higher than that of the pure blend, and the T_g value shifted toward higher temperatures when the volume fraction of sericin increased. TGA indicated that sericin retarded the thermal degradation; this depended on the filler concentration. The mechanical and electrical properties, such as the tensile strength, alternating‐current electrical conductivity, dielectric constant, and dielectric loss of the composites, were higher than those of the pure blend, and these properties were enhanced when the concentration of sericin was increased up to 10 wt % filler content, whereas the elongation at break of the composite decreased with the addition of sericin particles. The antibacterial properties of the composite showed that sericin had a significant inhibitory effect against S. aureus. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43535.     

Effect of a carbon black surface treatment on the microwave properties of poly(ethylene terephthalate)/carbon black composites

A surface treatment was applied to carbon black to improve the electrical and microwave properties of poly(ethylene terephthalate) (PET)-based composites. Three different formamide solutions with 1, 2, and 3 wt % concentrations were prepared to modify the surface chemistry of carbon black. Microwave properties such as the absorption loss, return loss, insertion loss, and dielectric constant were measured in the frequency range of 8–12 GHz (X-band range). Composites containing formamide-treated carbon black exhibited enhancements in the electrical conductivity, electromagnetic interference (EMI) shielding effectiveness, and dielectric constant values when compared to composites with untreated carbon black. In addition, increases in the formamide solution concentration and carbon black content of composites resulted in an increase in the electrical conductivity, EMI shielding effectiveness, and dielectric constant values. The percolation threshold concentration of PET composites shifted from a 3 to 1.5 wt % carbon black composition with the surface treatment. The best EMI shielding effectiveness was around 27 dB, which was obtained with the composite containing 8 wt % carbon black treated with a 3 wt % formamide solution. Moreover, this composition gave the lowest electrical resistivity and the highest dielectric constant among the produced composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Influence of environmental conditioning on the shear behavior of poly(phenylene sulfide)/glass fiber composites

Advanced thermoplastic composites are an alternative because of their ease of processing and storage. Poly(phenylene sulfide) (PPS) stands out among these materials because of its structural characteristics; for instance, it provides size, shape, and thermal stability, low moisture absorption, excellent chemical resistance, and good mechanical properties, including flexure, strength, and shear properties, compared to thermoset composites. Thus, the objective of this study was to evaluate the influence of environmental conditioning on the shear strength behavior of PPS/glass fiber composites. For this reason, first, some samples were treated to UV‐light exposure in a chamber. Other samples were immersed in seawater and hygrothermal baths simultaneously. They were tested with the interlaminar shear strength (ILSS) and Iosipescu shear test methods. The shear values obtained for the treated samples were compared against the dry sample values. For all samples tested with the ILSS and Iosipescu methods, the results indicate that the PPS/glass fiber composites presented a decrease in shear strength after they were submitted to hygrothermal and seawater solution conditioning. The moisture absorption was not uniform throughout the material, and wet conditioning induced strong matrix plasticization, which reduced the shear strength values of the laminates. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of carbon nanotube purification on the electrical and mechanical properties of poly(ethylene terephthalate) composites with carbon nanotubes in low concentration

Surface properties of carbon nanotubes (CNTs) were altered by purification with nitric acid, sulfuric acid, ammonium hydroxide, and hydrogen peroxide. As‐received and purified CNT‐based conductive poly (ethylene terephthalate) composites were prepared with a twin‐screw extruder. The effects of CNT purification on the surface properties of the CNTs and on the morphology and electrical and mechanical properties of CNT‐based composites were investigated. Surface energy measurements showed that the acidic component of the surface energies of the CNTs increased after purification. According to Fourier transform infrared (FTIR) spectroscopy, the purification resulted in the formation of oxygen‐containing functional groups on the surfaces of the CNTs. Electron spectroscopy for chemical analysis results indicate the removal of the metallic catalyst residues and an increase in the oxygen content of the CNT surfaces as a result of the purification procedure. X‐ray diffraction analyses revealed a change in the crystalline structure of the CNTs after purification. All of the composites prepared with the purified CNTs had higher electrical resistivities and tensile and impact strength values than the composites based on the as‐received CNTs because of the functional groups and defect sites formed on the surfaces of the CNTs during purification. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation and properties of poly(ethylene terephthalate)/inorganic whiskers composites

To improve the crystallization and mechanical properties of poly(ethylene terephthalate) (PET), in this work, PET/SiO₂‐MgO‐CaO whiskers composites were prepared via in situ polymerization. The morphology, crystallization, and mechanical properties of the prepared composites were investigated. It was found that inorganic whiskers could be easily dispersed in PET matrix, as demonstrated by SEM and PLM. DSC and PLM observation indicated a strong nucleation capability of inorganic whiskers for PET. Mechanical analysis results showed that the glass transition temperature, tensile strength, and modulus of the composites were greatly improved. A possible chemical bonding between PET chains and the surface of whiskers was observed by FTIR, TGA, and sedimentation experiment. It could be the main reason for the good dispersion and improved properties of the prepared composites. This work is important for the application of PET due to the low cost but high reinforcing efficiency of this inorganic whisker. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synthesis and characterization of poly(3‐octylthiophene)/single wall carbon nanotube composites for photovoltaic applications

In situ polymerization of P3OT with SWCNT is carried out in the presence of a FeCl₃ oxidant in a chloroform medium. The characterization of the composites is performed with FTIR, Raman, ¹H‐NMR, UV–Vis, PL spectroscopy, XRD, SEM, TEM, and conductivity measurements. The change (if any) in CC symmetric and antisymmetric stretching frequencies in FTIR, the shift in G band frequencies in Raman, any alterations in λ_max of UV–Vis and PL spectroscopic measurements are monitored with SWCNT loading in the polymer matrix. ¹H‐NMR confirms the wrapping of the polymer on to the SWCNT indicating lack of mobility. The work function values and the optical band gap values also support this view. The in situ polymerization procedure of the donor polymer molecules and the acceptor carbon nanotubes has resulted in enhanced dispersibility and stability of the composites in organic solvents. However, the principal focus of the study is to understand the interaction between the polymer and the SWCNTs, as the interface plays an important role in its application in the photovoltaic cells. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of nylon 6/polyalkylaniline conducting composites

Conducting composite films of polyalkylanilines with nylon 6 as the insulating matrix were electrochemically synthesized and characterized. The electrochemical properties of the alkylanilines and their composites were investigated with a cyclic voltammetry technique. The magnetic properties of the polymers and composites were analyzed, and their conducting mechanisms were found to be of bipolaron nature. With Fourier transform infrared spectra, it was clarified that polymerization occurred via the ? NH₂ group in a head‐to‐tail mechanism. Through thermogravimetric analyses, the thermal properties of the polymers and their composites were elucidated. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1693–1701, 2003     

Effect of ZnO type and concentration on the mophology,thermal, and mechanical properties of poly(ether ester)/ZnO composites

Poly(ether ester) (PEE) copolymers were synthesized in a two‐stage process involving transesterification and polycondensation. The synthesized copolymer and the zinc oxide (ZnO) were used in composite preparation by melt compounding. The influence of ZnO type and concentration on the morphology, thermal and mechanical properties of the composites were studied. DSC and XRD analyses indicated that crystallinity of composites was slightly reduced with ZnO content. Homogeneous dispersion of fillers in the polymer matrix was observed through morphological analyses. While in general tensile strength and elongation at break values of the composites decreased with increasing ZnO content, elastic modulus values increased with the addition of ZnO. Moreover, ZnO particles were modified with poly(N‐vinyl pyrrolidone) and a slight improvement in mechanical properties was observed, respectively over the composites containing unmodified particles. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Synthesis and characterization of poly(n‐undecyl isocyanate)/polyaniline polyblend

Poly(n‐undecyl isocyanate) (PUDIC)/n‐dodecylbenzenesulfonic acid (DBSA)‐doped polyaniline (PANIDBSA) polyblend was prepared and the effect of the H‐bonding between these two polymers on the compatibility, conjugation chain length of PANIDBSA, and helixity of PUDIC in the polyblend system were studied. The monomer and polymer were characterized by NMR spectra and the polyblend was analyzed by FTIR, UV–vis spectra, and wide‐angle X‐ray diffraction. It was found when the blend composition of the PUDIC was higher than 10%, the WAXD patterns demonstrated lower angle shifting for the peaks at around 2θ = 2–2.5°, referring to the distance between the layers of the layered structure of PANIDBSA crystalline with increasing PUDIC, indicating the expansion of the layered structure of PANIDBSA. The FTIR spectra illustrated the presence of an absorption peak at 1700 cm^?1 shift to higher wave number with PUDIC due to its H‐bonding with PANIDBSA. The UV–vis spectra of PANIDBSA described a blue‐shift of the λ_max with PUDIC, indicating that the presence of PUDIC in the polyblend system can interrupt and decrease the conjugation chain length of PANIDBSA. The optical activity of the helical PUDIC decreased notably with the presence of PANIDBSA, resulting from the reversed helical effect (de‐nature) of H‐bonding. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis and characterization of novel polythiophenes containing poly(ethylene oxide) side chains

Thiophene copolymers and their derivatives with poly(ethylene oxide) side chains were synthesized. The starting monomers were 3‐hexylthiophene and 2‐(3‐thienyl) ethanol with poly(ethylene oxide) grafted to the side chains. New functionalized polythiophenes were prepared by both chemical oxidation with FeCl₃ and electropolymerization. The conjugating polymers were characterized. The structures of the polythiophene derivatives agreed with the design. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1803–1808, 2006     

Preparation and characterization of poly(vinyl chloride)/virgin and treated sisal fiber composites

Mechanical property changes, thermal stability, and water absorption capacity of poly(vinyl chloride) (PVC)/sisal fiber composites were assessed with respect to the effect of maleic anhydride chemical treatments of the sisal fiber, for five different sisal fiber contents, varying from 0 to 30% by weight in the composite. The composites prepared with the untreated sisal exhibited higher tensile modulus and hardness than the unloaded resin, while elongation and tensile strength were reduced. The deterioration in the mechanical properties of PVC blended with sisal fiber is attributed to the presence of moisture, interfacial defects at the fiber and polymer interface, and fiber dispersion in the PVC matrix. The amount of absorbed water is a function of the amount of fiber in the composite (F0 = 0 phr, F5 = 0.77 phr, and F20 = 4.83 phr). The comparison of the results of characterization of F5, F20, and F30 formulations prepared with the untreated fibers and the treated ones showed a reduction in absorbed water after the chemical treatment of fiber with maleic anhydride (F0 = 0 phr, F5 = 0.28 phr, and F20 = 2.99 phr), thus improving the mechanical properties of composites prepared with the treated sisal. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 3630–3636, 2007     

Preparation and characterization of poly(vinyl alcohol) biocomposites with microalgae ash

Gasification of microalgae feedstock generates mineral ash. In this work, raw ash is produced from lipid‐extracted algal biomass of the Nannochloropsis salina strain. Prior to using it as filler for composite fabrication with poly(vinyl alcohol), raw ash (RASH) is activated with NaOH and surface modified with (3‐aminopropyl)triethoxysilane. Surface modification of activated ash (PASH) significantly improves interfacial interaction between surface‐modified ash (GASH) and polymer matrix. Higher ultimate tensile strength of PVA/GASH composites is recorded, compared with PVA/RASH and PVA/PASH. Young's modulus of biocomposites appears to increase proportionally to loading of the fillers. Thermal properties of polymeric materials of PVA with these ashes are stable. This is the first report to demonstrate the utilization of microalgal ash, the leftover after completed gasification of algal biomass, as an efficient filler for production of value‐added polymeric materials. It is proposed that microalgal ash is capable of improving the economic feasibility of microalgae‐based biorefinery. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43599.     

Synthesis and characterization of secondary doped polypyrrole/organic modified attapulgite conductive composites

Secondary doping method was introduced into fabricating polypyrrole/oganic modified attapulgite conductive composites. The preparation conditions, such as amount of hexadecylpyridinium chloride (CPC, modifying agent), organic modified attapulgite (OATP), and HCl (secondary dopant) have been optimized to get the composites with the highest conductivity. When m_CPC/m_ATP, m_OATP/m_Py, and n_HCl/n_SA (SA is sulfamic acid) reaches 0.03, 0.6, and 0.5, respectively, the PPy/OATP composites possess the highest conductivity of 87.59 S cm^?1 as well as the highest thermal degradation temperature of 249.29°C. Scanning electron microscopy, transmission electron microscopy, X‐ray diffraction, Fourier transform infrared spectroscopy, UV‐Visible diffuse reflectance study, and X‐ray photoelectron Spectroscopy results showed that PPy chains form the core‐shell structure and may combine with OATP via π–π stacking interaction. Thermogravimetric analysis showed that the thermal stability of PPy/OATP‐SH composites was enhanced and these could be attributed to the retardation effect of OATP as barriers for the degradation of PPy. This method may open a new door for PPy‐based composites with special structures, higher performance, and thus broader application ranges. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41407.     

Thermal and dynamic mechanical behavior of poly(vinyl chloride)/wood flour composites

Thermal and dynamic mechanical behaviors of wood plastic composites made of poly vinyl chloride (PVC) and surface treated, untreated wood flour were characterized by using differential scanning calorimetry and dynamic mechanical analysis. Glass transition temperature (T_g) of PVC was slightly increased by the addition of wood flour and by wood flour surface treatments. Heat capacity differences (ΔC_p) of composites before and after glass transition were markedly reduced. PVC/wood composites exhibited smaller tan δ peaks than PVC alone, suggesting that less energy was dissipated for coordinated movements and disentanglements of PVC polymer chains in the composites. The rubbery plateaus of storage modulus (E′) curves almost disappeared for PVC/wood composites in contrast to a well defined plateau range for pure PVC. It is proposed that wood flour particles act as “physical crosslinking points” or “pinning centers” inside the PVC matrix, resulting in the absence of the rubbery plateau and high E′ above T_g. The mobility of PVC chain segments were further retarded by the presence of surface modified wood flour. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008