An Efficient Summer Operation Scheme for a Thermal Power Plant Air Cooling System based on Electric Peak Shaving

We proposed a novel efficient operation scheme for a thermal power plant’s air-cooling system based on peak shaving, in order to cope with high ambient temperature in summer. We introduced an absorptiongeneration equipment with water/lithium working pairs into the air cooled condenser(ACC) to reconstruct the traditional thermal power plant, and established a dynamic thermodynamic model adopting Ebsilon code. We studied the thermodynamic performance variation of the reconstructed thermal power pl...     

Thermodynamic analysis of novel hybrid liquid air energy storage system combined with ORC

为了进一步提高液态空气储能（LAES）的系统效率，提出了一种利用有机朗肯循环（ORC）回收利用LAES放电过程中余冷和余热的新型LAES系统。采用Aspen HYSYS V8.4流程模拟方法研究了系统中不同设备性能参数对LAES系统热力特性的影响。结果表明：低温泵等熵效率和换热器夹点温度对LAES系统效率的影响较小；透平等熵效率和燃烧室出口温度对LAES系统效率的影响非常显著，LAES系统效率随透平等熵效率和燃烧室出口温度的增加而显著增加；LAES系统效率随低温泵出口压力的升高而增加，但增加幅度会逐渐减小。该研究结果可为LAES系统的工程应用和效率提升提供重要参考和依据。     

Brayton refrigeration cycle for gas turbine inlet air cooling

In this paper, a new approach to enhance the performance of gas turbines operating in hot climates is investigated. Cooling the intake air at the compressor bell mouth is achieved by an air Brayton refrigerator (reverse Joule Brayton cycle) driven by the gas turbine and uses air as the working fluid. Fraction of the air is extracted from the compressor at an intermediate pressure, cooled and then expands to obtain a cold air stream, which mixes with the ambient intake. Mass and energy balance analysis of the gas turbine and the coupled Brayton refrigerator are performed. Relationships are derived for a simple open gas turbine coupled to Brayton refrigeration cycle, the heat rejected from the cooling cycle can be utilized by an industrial process such as a desalination plant. The performance improvement in terms of power gain ratio (PGR) and thermal efficiency change (TEC) factor is calculated. The results show that for fixed pressure ratio and ambient conditions, power and efficiency improvements are functions of the extraction pressure ratio and the fraction of mass extracted from the air compressor. The performance improvement is calculated for ambient temperature of 45°C and 43.4% relative humidity. The results indicated that the intake temperature could be lowered below the ISO standard with power increase up to 19.58% and appreciable decrease in the thermal efficiency (5.76% of the site value). Additionally, the present approach improved both power gain and thermal efficiency factors if air is extracted at 2 bar which is unlike all other mechanical chilling methods. Copyright © 2007 John Wiley & Sons, Ltd.     

Analysis of parameters affecting the performance of gas turbines and combined cycle plants with vapor absorption inlet air cooling

The integration of an aqua‐ammonia inlet air‐cooling scheme to a cooled gas turbine‐based combined cycle has been analyzed. The heat energy of the exhaust gas prior to the exit of the heat recovery steam generator has been chosen to power the inlet air‐cooling system. Dual pressure reheat heat recovery steam generator is chosen as the combined cycle configuration. Air film cooling has been adopted as the cooling technique for gas turbine blades. A parametric study of the effect of compressor–pressure ratio, compressor inlet temperature, turbine inlet temperature, ambient relative humidity, and ambient temperature on performance parameters of plants has been carried out. It has been observed that vapor absorption inlet air cooling improves the efficiency of gas turbine by upto 7.48% and specific work by more than 18%, respectively. However, on the adoption of this scheme for combined cycles, the plant efficiency has been observed to be adversely affected, although the addition of absorption inlet air cooling results in an increase in plant output by more than 7%. The optimum value of compressor inlet temperature for maximum specific work output has been observed to be 25 °C for the chosen set of conditions. Further reduction of compressor inlet temperature below this optimum value has been observed to adversely affect plant efficiency. Copyright © 2013 John Wiley & Sons, Ltd.     

火电站直接空冷凝汽器积灰监测

火电站直接空冷凝汽器积灰是影响传热性能的重要因素,研究直接空冷凝汽器积灰对传热性能的影响规律并提出监测措施具有重要意义。通过分析汽轮机背压与汽轮机排汽量、冷却空气流量、凝汽器传热系数、凝汽器总传热面积以及环境温度之间的关系,得到了空冷凝汽器在维持汽轮机排汽量和冷却空气量不变时,汽轮机背压和传热系数之间的关系以及凝汽器积灰对汽轮机背压的影响。研究表明:凝汽器积灰会导致凝汽器传热系数降低,汽轮机背压升高,机组运行经济性下降。设计工况下,当蛇形翅片扁平管结构凝汽器积灰厚度达到1.2 mm时,汽轮机背压将增加50%左右。通过监测空冷机组运行过程中汽轮机背压的变化,可预报积灰的程度,为直接空冷凝汽器清洗提供一定的理论依据。     

1000MW直接空冷机组变工况特性

以1 000MW直接空冷机组为例,基于η-NTU法,建立了直接空冷机组变工况数学模型。在模型中考虑了排汽管道压降及机组对环境散热量等因素,编程计算做出了凝汽器排汽压力与环境温度、迎面风速、排汽流量间的特性曲线。得出迎面风速为2.2m/s左右时,排汽压力波动范围接近额定值,机组的运行良好。为同类1 000MW空冷机组在变工况下选择合适的运行值和提高经济性提供了参考。     

Preliminary analysis of compound systems based on high temperature fuel cell, gas turbine and Organic Rankine Cycle

This article presents a novel proposal for complex hybrid systems comprising high temperature fuel cells and thermal engines. In this case, the system is composed by a molten carbonate fuel cell with cascaded hot air turbine and Organic Rankine Cycle (ORC), a layout that is based on subsequent waste heat recovery for additional power production. The work will credit that it is possible to achieve 60% efficiency even if the fuel cell operates at atmospheric pressure.The first part of the analysis focuses on selecting the working fluid of the Organic Rankine Cycle. After a thermodynamic optimisation, toluene turns out to be the most efficient fluid in terms of cycle performance. However, it is also detected that the performance of the heat recovery vapour generator is equally important, what makes R245fa be the most interesting fluid due to its balanced thermal and HRVG efficiencies that yield the highest global bottoming cycle efficiency. When this fluid is employed in the compound system, conservative operating conditions permit achieving 60% global system efficiency, therefore accomplishing the initial objective set up in the work.A simultaneous optimisation of gas turbine (pressure ratio) and ORC (live vapour pressure) is then presented, to check if the previous results are improved or if the fluid of choice must be replaced. Eventually, even if system performance improves for some fluids, it is concluded that (i) R245fa is the most efficient fluid and (ii) the operating conditions considered in the previous analysis are still valid.The work concludes with an assessment about safety-related aspects of using hydrocarbons in the system. Flammability is studied, showing that R245fa is the most interesting fluid also in this regard due to its inert behaviour, as opposed to the other fluids under consideration all of which are highly flammable.     

A study on performance of solid oxide fuel cell‐organic Rankine cycle combined system

This study presents an energetic performance analysis for a combined power generation system consisting of a solid oxide fuel cell (SOFC) and an organic Rankine cycle (ORC). In order to simulate the SOFC–ORC combined system under steady‐state conditions, a mathematical model is developed. The developed model is used to determine the potential effects caused by the changes of the design parameters on the energetic performance of the combined system. As design parameters, turbine inlet pressure, condenser temperature, fuel utilization, current density, compressor pressure ratio, and cell operating temperature are taken into account. In this regard, the electrical power and First Law efficiency are estimated by parametrical analysis and discussed comprehensively. Results of these analyses show that the efficiency is increased about 14–25% by recovering SOFC waste heat through ORC based on investigated design parameter conditions. Copyright © 2008 John Wiley & Sons, Ltd.     

First and second law analysis of solar operated combined Rankine and ejector refrigeration cycle

A combined Rankine and ejector refrigeration cycle is proposed for the production of power and refrigeration output using duratherm 600 oil as the heat transfer fluid. Thermodynamic analysis has been done to observe the effect of parameters on the performance of the combined cycle. The effect of various parameters asthe turbine inlet pressure, evaporator temperature, condenser temperature, extraction ratio and direct normal radiation per unit area on the performance of the cycle have significant effects on the net power output, refrigeration output, first law efficiency and second law efficiency. It is also observed that the maximum irreversibility occurs in central receiver as 52.5% followed by 25% in the heliostat, 5.3% in the heat recovery vapor generator, 2.6% in the ejector, and 1.6% in the turbine and around 1.1% in the other components of the cycle. The second law efficiency of the solar operated combined Rankine and ejector refrigeration cycle is 11.90% which is much lower than its first law efficiency of 14.81%.     

Performance and parametric investigation of a binary geothermal power plant by exergy

Exergy analysis of a binary geothermal power plant is performed using actual plant data to assess the plant performance and pinpoint sites of primary exergy destruction. Exergy destruction throughout the plant is quantified and illustrated using an exergy diagram, and compared to the energy diagram. The sites with greater exergy destructions include brine reinjection, heat exchanger and condenser losses. Exergetic efficiencies of major plant components are determined in an attempt to assess their individual performances. The energy and exergy efficiencies of the plant are 4.5% and 21.7%, respectively, based on the energy and exergy of geothermal water at the heat exchanger inlet. The energy and exergy efficiencies are 10.2% and 33.5%, respectively, based on the heat input and exergy input to the binary Rankine cycle. The effects of turbine inlet pressure and temperature and the condenser pressure on the exergy and energy efficiencies, the net power output and the brine reinjection temperature are investigated and the trends are explained.     

Parametric analysis for a new combined power and ejector–absorption refrigeration cycle

A new combined power and ejector–absorption refrigeration cycle is proposed, which combines the Rankine cycle and the ejector–absorption refrigeration cycle, and could produce both power output and refrigeration output simultaneously. This combined cycle, which originates from the cycle proposed by authors previously, introduces an ejector between the rectifier and the condenser, and provides a performance improvement without greatly increasing the complexity of the system. A parametric analysis is conducted to evaluate the effects of the key thermodynamic parameters on the cycle performance. It is shown that heat source temperature, condenser temperature, evaporator temperature, turbine inlet pressure, turbine inlet temperature, and basic solution ammonia concentration have significant effects on the net power output, refrigeration output and exergy efficiency of the combined cycle. It is evident that the ejector can improve the performance of the combined cycle proposed by authors previously.     

Experimental investigation of pressurized packing saturator for humid air turbine cycle

Humid air turbine (HAT) cycle is an advanced power generation system, and its efficiency and output power are improved by humidifying the compressed air. This humidification process is completed in the saturator. Therefore, the humidifying performance of saturator has great influence on the performance of HAT cycle. In this work, a new type packing saturator was designed and a series of experiments were carried out to study its humidifying performance. In order to improve the uniformity of the saturator inlet, a twin-tangential annular flow gas distributor was designed. Then it was authorized by China invention patents (ZL201010200778.9). Now, the mal-distribution factor of inlet air is mainly between 0.15 and 0.35 in all experimental conditions. Some key parameters of air and water at the inlet and outlet of saturator were measured at different experimental conditions. These results show the outlet humid air temperature is an important parameter for determining the humidifying amount of the saturator. The humidifying performance of the saturator is mainly affected by the inlet water temperature and the liquid/gas (L/G) ratio. At the same operating pressure, the humidity ratio of outlet humid air increases with inlet water temperature and L/G ratio. At higher inlet water temperature, the L/G ratio has a greater effect on the humidity ratio of outlet humid air. The outlet water temperature is mainly affected by the inlet gas temperature. With the increasing of inlet air temperature, the outlet water temperature increases, and it is close to the wet-bulb temperature of inlet air.     

Performance enhancement of gas turbines by inlet air‐cooling in hot and humid climates

In this paper, a model to study the effect of inlet air‐cooling on gas turbines power and efficiency is developed for two different cooling techniques, direct mechanical refrigeration and an evaporative water spray cooler. Energy analysis is used to present the performance improvement in terms of power gain ratio and thermal efficiency change factors. Relationships are derived for an open gas turbine cycle with irreversible compression and expansion processes coupled to air‐cooling systems. The obtained results show that the power and efficiency improvements are functions of the ambient conditions and the gas turbine pressure ratio. The performance improvement is calculated for, ambient temperatures from 30 to 50°C, the whole range of humidity ratio (10–100%) and pressure ratio from 8 to 12. For direct mechanical refrigeration air‐cooling, the power improvement is associated with appreciable drop in the thermal efficiency. The maximum power gain can be obtained if the air temperature is reduced to its lowest limit that is the refrigerant evaporation temperature plus the evaporator design temperature difference. Water spray cooling process is sensitive to the ambient relative humidity and is suitable for dry air conditions. The power gain and efficiency enhancement are limited by the wet bulb temperature. The performance of spray evaporative cooler is presented in a dimensionless working graph. The daily performance of the cooling methods is examined for an ABB‐11D5 gas turbine operating under the hot humid conditions of Jeddah, Saudi Arabia. The results indicate that the direct mechanical refrigeration increased the daily power output by 6.77% versus 2.57% for the spray air‐cooling. Copyright © 2005 John Wiley & Sons, Ltd.     

On site experimental evaluation of a low-temperature solar organic Rankine cycle system for RO desalination

The paper presents the on site experimental evaluation of the performance of a low-temperature solar organic Rankine cycle system (SORC) for reverse osmosis (RO) desalination. This work is a research step forward to the experimental evaluation of the SORC under laboratory conditions, where the system was tested using an electric brake as load and an electric thermal heater as heat supply. The difference is that solar collectors have been applied as heat supply and there has been a realistic investigation of the performance of the system under the conditions implied by solar energy. The thermal energy produced by the solar collectors’ array evaporates the refrigerant HFC-134a in the pre-heater-evaporator surfaces of the Rankine engine. The superheated vapour is then driven to the expander, where the generated mechanical work produced from expansion drives the high-pressure pump of the RO desalination unit. The superheated vapour at the expander’s outlet is directed to the condenser and condensates. Finally, the saturated liquid at the condenser outlet is pressurized by a positive displacement pump and the thermodynamic cycle is repeated. A special energy recovery system of Axial Pistons Pumps (APP) has been integrated into the RO unit to minimise the specific energy consumption. The results prove that the above concept is technically feasible and continuous operation is achieved under the intermittent availability of solar energy. However, considerably low efficiency has been observed, in comparison with the results taken under controlled thermal load. Nevertheless, it becomes apparent that further optimisation work is required to improve the system efficiency. The research work has been done within the framework of COOP-CT-2003-507997 contract, partly financed by EC.     

Analysis of the power cycle utilizing the cold energy of LNG

The aim of this study is to analyse the performance of the Rankine power cycles operating with the LNG as the heat sink and with the seawater as the heat source. A model for the power cycle utilizing the cold energy of the LNG is established and a cycle simulation is carried out to analyse the performance characteristics. The analysis reveals that there exist optimum values in the condenser-outlet temperatures of the LNG and the ratio of heat transfer capacity of the condenser to the total capacity of the condenser and the vapour generator. An additional finding of this study is that near the point of maximum net work, the heat transfer capacity of the vapour generator becomes larger than that of the condenser, as opposed to the cases of a general Rankine cycle. Also the results of this study illuminate several advantages of using binary mixtures as working fluids over the use of pure substances.     

Wind effect on the performance of a solar organic Rankine cycle

The effects of wind, ambient temperature and solar radiation on the simultaneous productions of mechanical work and heat by a solar Rankine cycle are studied. The on site experimental study uses the pentafluorobutane R365mfc as working fluid in a system consisting of a small-scale single glazed flat plate collector, a micro turbine, a condenser and a pump. The theoretical study focuses on the prediction of the optimum operating temperature of the collector according to the solar radiation, the temperature of air and the wind speed. Then, the total production of mechanical and thermal energy is calculated during a sunny day for which various wind speeds are simulated. The results highlight the effect of wind on the corresponding production and they also establish the value of the recommended evaporating temperature according to weather conditions.     

Evaluation of cooling technologies of concentrated solar power plants and their combination with desalination in the mediterranean area

Different alternatives for the effective integration of desalination technologies in the cooling of concentrating solar power (CSP) plants in the Mediterranean area are discussed and evaluated. Two cases are considered where a low temperature multi-effect distillation (LT-MED) plant is integrated into a CSP plant replacing the condenser of the power cycle. In one case, a LT-MED plant is fed by steam at the outlet of the turbine expanded to 70 °C. In the other case a LT-MED is fed by the steam obtained from a thermal vapour compressor (TVC) which uses the exhaust steam of the CSP plant (at 37 °C, 0.063 bar) together with some from the high pressure turbine extraction (17 bar). The two cases are compared with that of a reverse osmosis (RO) unit powered by the electricity produced by the CSP plant. In this case, two different wet cooling technologies, once-through and evaporative water cooling, and a dry air cooling are considered for the CSP plant. Thermodynamic simulations are presented for all cases, together with an economic analysis.     

Analysis of optimization in an OTEC plant using organic Rankine cycle

This study quantified the effects of evaporation temperature, condensation temperature, and the inlet- and outlet-temperature differences of deep cold seawater and warm seawater on the performance of an ocean thermal energy conversion (OTEC) plant using an organic Rankine cycle (ORC), and also investigated the optimal operations required for the performance. A finite-temperature-difference heat transfer method is developed to evaluate the objective parameter, which is the ratio of net power output to the total heat transfer area of heat exchanger in the system, and R717, R600a, R245fa, R152a, and R134a were used as the working fluids. The optimal evaporation and condensation temperatures were obtained under various conditions for maximal objective parameters in an OTEC system.The results show that R717 performed optimally in objective parameter evaluation among the five working fluids, and that R600a performed better than other fluids in thermal efficiency analysis. The optimal seawater temperature differences between the inlet and outlet of the evaporator and condenser are proposed. Furthermore, the influences of inlet temperatures of warm and cold seawater in the ORC are presented for an OTEC plant. The simulation results should enable the performance of an ORC system to be compared when using various organic working fluids.     

A study of organic working fluids on system efficiency of an ORC using low-grade energy sources

Rankine cycles using organic fluids (as categorized into three groups: wet, dry, and isentropic fluids) as working fluids in converting low-grade energy are investigated in this study. The main purpose is to identify suitable working fluids which may yield high system efficiencies in an organic Rankine cycle (ORC) system. Efficiencies of ORC systems are calculated based on an assumption that the inlet condition of the working fluid entering turbine is in saturated vapor phase. Parameters under investigation are turbine inlet temperature, turbine inlet pressure, condenser exit temperature, turbine exit quality, overall irrversibility, and system efficiency. The low-grade energy source can be obtained from a solar pond or/and an ocean thermal energy conversion (OTEC) system. Results indicate that wet fluids with very steep saturated vapor curves in T-s diagram have a better overall performance in energy conversion efficiencies than that of dry fluids. It can also be shown that all the working fluids have a similar behavior of the efficiency-condenser exit temperature relationship. Furthermore, an appropriate combination of solar energy and an ORC system with a higher turbine inlet temperature and a lower condenser temperature (as operated deeply under sea level) would provide an economically feasible and environment-friendly renewable energy conversion system.     

Power and efficiency optimization for combined Brayton and inverse Brayton cycles

A thermodynamic model for open combined Brayton and inverse Brayton cycles is established considering the pressure drops of the working fluid along the flow processes and the size constraints of the real power plant using finite time thermodynamics in this paper. There are 11 flow resistances encountered by the gas stream for the combined Brayton and inverse Brayton cycles. Four of these, the friction through the blades and vanes of the compressors and the turbines, are related to the isentropic efficiencies. The remaining flow resistances are always present because of the changes in flow cross-section at the compressor inlet of the top cycle, combustion inlet and outlet, turbine outlet of the top cycle, turbine outlet of the bottom cycle, heat exchanger inlet, and compressor inlet of the bottom cycle. These resistances control the air flow rate and the net power output. The relative pressure drops associated with the flow through various cross-sectional areas are derived as functions of the compressor inlet relative pressure drop of the top cycle. The analytical formulae about the relations between power output, thermal conversion efficiency, and the compressor pressure ratio of the top cycle are derived with the 11 pressure drop losses in the intake, compression, combustion, expansion, and flow process in the piping, the heat transfer loss to the ambient, the irreversible compression and expansion losses in the compressors and the turbines, and the irreversible combustion loss in the combustion chamber. The performance of the model cycle is optimized by adjusting the compressor inlet pressure of the bottom cycle, the air mass flow rate and the distribution of pressure losses along the flow path. It is shown that the power output has a maximum with respect to the compressor inlet pressure of the bottom cycle, the air mass flow rate or any of the overall pressure drops, and the maximized power output has an additional maximum with respect to the compressor pressure ratio of the top cycle. When the optimization is performed with the constraints of a fixed fuel flow rate and the power plant size, the power output and efficiency can be maximized again by properly allocating the fixed overall flow area among the compressor inlet of the top cycle and the turbine outlet of the bottom cycle.