横向双模双频滤波器设计

基于横向滤波器耦合结构,采用支节加载双模谐振器,设计了中心频率位于1.57 GHz(GPS应用)与2.4GHz(WLAN应用)的双频微带滤波器。由短路支节加载双模谐振器形成第一个通带,开路支节加载双模谐振器形成第二个通带,两个谐振器被输入/输出馈线隔离,每个通带的中心频率与带宽可以单独调节。测试结果表明:两个通带内的最小插损分别为2.18,1.35 dB,3 dB带宽分别为5.2%,6.8%,回波损耗均小于16 dB,三个传输零点分别位于1.28,2.08,2.71 GHz处。该滤波器具有尺寸小、带外选择性好等优点。     

基于T型枝节加载SIR的双频微带滤波器的设计

针对当前通信系统需要滤波器支持多频段、小型化和高性能等要求,提出了一种基于T型枝节加载SIR的频率独立可控双频微带滤波器结构。针对该谐振器,利用提出的特殊电耦合结构实现滤波器的小型化,并引入零度馈电结构构造传输零点来改善阻带抑制,最终得到覆盖WLAN 2.4 GHz和WLAN 5.2 GHz两个频段且占用尺寸仅为16.5 mm×21.7 mm的双频微带带通滤波器。由仿真结果显示,两个通带的中心频率分别为2.45 GHz和5.2 GHz,带内最小插入损耗分别为0.35 dB和0.47 dB,带内最小回波损耗分别为-44 dB和-34.8 dB,3 dB相对带宽分别为28.9%和11.3%,阻带抑制也因引入三个传输零点而大大改善。该滤波器结构整体尺寸小、插损低、频带宽且带外抑制特性好,具有一定的实际应用价值。     

基于奇偶模分析法的四模谐振器结构的双通带带通滤波器设计

提出了一款基于四模谐振器的新型双通带带通滤波器.设计的四模谐振器基于微带线结构,由四个开路枝节和一个短路枝节组成.两次采用奇偶模分析法对该四模谐振器结构进行分析.该四模谐振器的每个模式能够实现独立调节,同时每两个模式形成一个通带.采用源与负载耦合的馈电方式,提高滤波器的带外抑制性.该滤波器具有四个传输零点和四个传输极点.测试结果表明,该双模双通带滤波器工作于2.08GHz和6.07GHz,3dB带宽分别为11.06%和7.74%.设计的滤波器具有紧凑的结构,只有0.28λ_g×0.11λ_g大小.     

基于双模开环谐振器的双频带滤波器设计

基于开环双模谐振器设计了一种双频带通滤波器,由两个中心重合的正方形开口环谐振器组成。分析该谐振器的奇偶模谐振频率与传输零点,每个通带内有两个谐振模式。该滤波器中心频率分别为4.5 GHz和6.5 GHz,3 dB相对带宽FBW分别为11%、5%,两通带带内插入损耗分别小于0.6 dB、1.4 dB,带内回波损耗分别优于19.5 dB、16.5 dB,高频处阻带抑制达到50 dB,两通带之间隔离度达到53 dB,尺寸仅为6 mm×11 mm×1.09 mm。     

应用于多模WLANs的紧凑SIR双频带通滤波器

提出了一种基于阶梯阻抗谐振器的紧凑、高选择性的微带双频带通滤波器,使用了两个发卡型阶梯阻抗谐振器交叉组成了伪交指结构谐振器,实现了小型化双频滤波器。采用0°馈电结构引入了三个传输零点,从而提高了频率选择特性。加工了微带双频带通滤波器实物,实测结果显示,两个通带中心频率分别为2.41GHz和5.26GHz,中心频率比大于2,带内插损分别为1.06dB和1.59dB,3dB相对带宽分别为22.8%、15.6%,仿真与实测吻合较好。与传统的分支加载、阶梯阻抗等双频滤波器相比,该滤波器具有设计简单、结构紧凑、低插入损耗及高频率选择特性等优点。     

基于方开环谐振器的双陷波超宽带滤波器

针对超宽带系统易受窄带信号干扰的问题,设计了一种可以抑制无线局域网络(WLAN)和卫星通信信号干扰的双陷波超宽带带通滤波器。该滤波器的主要谐振结构由T型枝节加载的多模谐振器组成,改进的T型枝节增加了两个传输零点,同时减小了滤波器尺寸;通过耦合方开环谐振器,实现了两个陷波特性,调节谐振器尺寸,可以得到所需的陷波频率。测试结果表明,该滤波器的尺寸仅16.7mm×8.5mm,中心频率为6.9GHz,通带为3.0~10.8GHz,陷波中心频率在5.8GHz和8.04GHz,衰减最低点分别为-27dB和-18dB,仿真与测量结果有较好的一致性。     

宽阻带小型化双频带通滤波器

文中提出了一种具有宽阻带的紧凑型双频带通滤波器,它采用了折叠短路枝节负载谐振器、紧凑型微 带单元谐振器(CMRC)和阶跃阻抗谐振器结构。由于多个谐振器产生了五个可控传输零点(TZ),该滤波器实现了两个 通带之间的良好隔离度以及宽阻带特性。制作并测试了尺寸紧凑的双频带通滤波器实验样品,测试结果显示,第一通 带和第二通带的中心频率/ 插入损耗分别为0. 66 GHz/0. 8 dB 和1. 73 GHz/0. 7 dB,阻带频率高达10. 5 GHz,抑制水平 超过15 dB。     

基于枝节加载环形谐振器的双频带滤波器

该文提出了一种新型的非对称枝节加载环形谐振器,并研究了该谐振器的性质。基于提出的谐振器设计了一款双频带通滤波器,并进行了测试。测试结果表明:滤波器的两个通带的中心频率分别为2.38 GHz和5.19 GHz,带宽分别约为140 MHz和90 MHz,带内插损分别小于1.7 dB和2.2 dB,回波损耗分别大于15 dB和12 dB。4个传输零点按频率由低到高分别为1.78 GHz,3.34 GHz,4.98 GHz和5.96 GHz,这些零点极大地提高了滤波器的选择性。     

双频带通滤波器的优化设计

利用阶跃阻抗谐振器优化,设计了一个工作在无线局域网(2.4/5.2GHz)的双频带通滤波器。通过奇、偶模分析,在阶跃阻抗谐振器理论计算公式基础上,根据不同的阻抗比条件,阶跃阻抗谐振器谐振频率比与阶跃阻抗高、低阻抗电长度之比的关系曲线,可以方便地确定阶跃阻抗谐振器的谐振频率和电长度,通过sonnet电路仿真软件验证了设计的合理性,并给出了用于无线通信2.4、5.2 GHz双频带通滤波器的设计结果。该带通滤波器可以分别在2.4、5.2 GHz处得到较好的通带性。由于交叉耦合的存在,该双频带通滤波器在两个通带端各有一个传输零点,以此来提高滤波器的通带频率选择性。最后,测量结果与仿真结果基本吻合。     

带SIR结构新型多枝节加载双频滤波器

本文在传统λ/4阶梯阻抗谐振器的基础上,提出了一种新型的宽带双频滤波器改进设计方案。改进的滤波器增加了传输零点,此传输零点能有效的改进通带的选择性和阻带特性,且上阻带带宽很宽。结构简单,在传统类似滤波器同谐振频率基础上有效缩小了尺寸,并且设计的滤波器通带的中心频率和带宽是完全独立可控,方便我们应用到实际。工作在4.1 GHz和6 GHz两个频段,3 dB相对带宽分别为7.2%和2.2%,实测和仿真吻合良好。     

A Dual-Band Combline Bandpass Filter Loaded by Lumped Series Resonators

This letter presents a dual-band combline bandpass filter (BPF) loaded by lumped series resonators. The proposed filter configuration can easily generate two desired passbands by controlling the resonant frequencies of the comblines as well as the series resonators. Furthermore, the skirt frequency characteristics between the two passbands are improved by transmission zeros introduced by source-load coupling via a lumped element capacitor. Two-pole dual-BPF with center frequencies of 1.2 and 1.54 GHz is designed and the measured results agree well with simulated results.     

一种紧凑型微带三频滤波器的设计

提出了一种新型微带三频滤波器,滤波器由两个弯折并相互嵌套的分支线谐振器和一个T形谐振器组成。谐振器之间相互耦合,得到三通带频率响应特性。该滤波器可通过调节微带线几何参数改变通带位置以及带宽,以满足不同应用需求。这种结构的滤波器结构紧凑,电路面积小,三个通带两边各引入一个传输零点,增强了通带间的隔离度以及阻带抑制特性。设计并制作了一款1.57/3.55/5.2GHz三通带滤波器,测试结果与仿真结果基本相符,验证了该滤波器结构的有效性。     

Dual-band bandpass filter with source-load coupling

A compact dual-band bandpass filter is presented for wireless LAN applications. Using two centrally-loaded stepped-impedance resonators, the second passband frequency can be conveniently tuned. Two transmission zeros are generated between the two passbands because of source-loading coupling topology. Simulated results show that two central frequencies are located at desired 2.4 and 5.7 GHz with 3 dB fractional bandwidths of 18.8 and 7.1 , respectively. Comparison of measured and simulated results shows good agreement.     

Compact triple-passband bandpass filter based on new modified stepped impedance resonators

This study proposed a triple-passband bandpass filter with compact size, low loss and high passband selectivity. The filter includes two coupled stepped impedance resonators (SIRs) and two embedded stub-loaded stepped impedance resonators (SL-SIRs), connected with coupling scheme at the symmetric plane of the filter. The filter is designed to have triple-passband at 2.4, 3.5 and 5.2 GHz for worldwide interoperability for microwave access (WiMAX) applications. By properly tuning the impedance ratio and physical length ratio of the SL-SIRs, the three passbands can be easily determined, at the same time, achieving the high passband selectivity and wide stopband. Besides, the transmission zeros near passband edges of each passband are generated by the proposed filter with cross-coupling structure. The measured results are in good agreement with the full-wave electromagnetic (EM) simulation results.     

Dual-Band Bandpass Filter Design Using a Novel Feed Scheme

A planar dual-band bandpass filter based on a novel feed scheme is presented in this letter. The proposed filter employs two sets of resonators operating at diverse frequencies to generate two passbands. A novel scheme is introduced to feed the resonators. One set of resonators is utilized to not only generate the lower passband but also feed other resonators. Source-load coupling for upper passband is inherently realized. This scheme provides sufficient degrees of freedom to control the center frequencies and bandwidth of the two passbands. Four transmission zeros can be created close to passband edges, resulting in high skirt selectivity. To validate the proposed idea, a demonstration filter is implemented. The design methodology, filter sensitivity and experimental results are presented.      

Multilayer Dual-Band Filter Using a Reflector Cavity and Dual-Mode Resonators

A dual-band filter has been designed using a multilayer approach. The structure includes a reflector cavity and dual-mode resonators. The walls of the reflector cavity have been designed using metalized vias enabling the integration characteristics of standard planar microwave circuits. The principle includes the passband division of a fourth-order fully canonical form into two narrowband second-order passbands. The designed topology exhibits a dual-band response with center frequencies of 5.2 and 5.7GHz and in-between isolation of 30 dB created by two in-band transmission zeros. The enclosing cavity reduces radiation loss and increases the unloaded of the resonant modes. The hybrid design provides insertion losses better than 1.7 dB and narrow fractional bandwidths of 2.5%.     

一种耦合线加载的双通带滤波器

提出一种基于耦合线加载的双通带滤波器,该滤波器在开口矩形环内部加载两根相互耦合的微带,从而产生两个通带。与加载单枝节的双通带滤波器相比,该滤波器在设计时有更多可变参数和更小的调节步进。比如当耦合线宽度不等步进变化时通带中心频率会向相反方向变化,这一性质可以用作对两通带之间的频率间隔进行微调。测试结果表明,该滤波器有两个通带,其中心频率分别为3.78 GHz 和6.55 GHz,相对带宽分别为4.6%和4.8%。除此之外,还研究了调整加载耦合线的长度和宽度对滤波器频率特性的影响。仿真和实测结果之间良好的吻合证实了设计方法的有效性。     

自均衡双通带微带滤波器综合与设计

 本文介绍了一种利用复传输零点设计自均衡双通带滤波器的方法,并用开环微带谐振器实现该滤波器电路.利用全波仿真软件,设计了一个12阶双通带自均衡高温超导薄膜微带滤波器.仿真结果显示该滤波器两个通带分别为2.631~2.679GHz,2.781~2.829GHz,阻带为2.681~2.779GHz,平坦的群时延占整个带宽60%以上.