立方体AgBrCl硫增感光的电子行为

本文利用微波吸收相敏检测技术 ,同时获得了立方体AgBrCl乳剂中 ,在增感温度增加的条件下 ,自由光电子和浅束缚光电子的时间衰减曲线 ,分析了不同的硫增感产物随增感温度增加所起的陷阱效应。结果表明 ,在立方体AgBrCl乳剂中 ,硫增感初始阶段的增感产物主要是作为浅电子陷阱存在 ;随着增感温度增加至5 5℃时 ,增感产物浅电子陷阱效果最佳 ;如增感温度进一步增加 ,硫增感中心又变为深电子陷阱。文中还讨论了浅电子陷阱中浅束缚光电子衰减时间与阱深的依存关系。     

还原增感立方体AgCl微晶光电子衰减特性

利用微波吸收介电谱检测技术测得了还原增感立方体氯化银微晶光电子衰减随增感条件的变化规律。实验发现,随增感条件的不同,增感中心发生了由空穴陷阱作用向深电子陷阱作用的转变。当增感中心起空穴陷阱作用时通过俘获空穴,降低了光电子与光空穴的复合几率,提高了光电子的利用率,从而有利于潜影的形成。由此得到在增感浓度一定时的最佳增感时间和最佳增感温度的组合。     

温度对还原增感立方体氯化银乳剂中光电子衰减的影响

利用微波介电检测技术,测得还原增感立方体氯化银乳剂中自由光电子与浅束缚光电子衰减行为随还原增感温度的变化。实验发现还原增感温度变化会引起增感中心陷阱作用的变化:当还原增感温度较低时,增感中心起空穴陷阱作用,延缓光电子衰减;还原增感温度较高时,增感中心起深电子陷阱作用,加速光电子衰减。由此,我们得到了确定最佳增感温度的依据。     

硫增感AgBrI T颗粒乳剂光电子行为研究

利用微波相敏技术，获得了硫增感AgBrI T颗粒乳剂中自由光电子和束缚光电子时间衰减信号，分析了光电子衰减时间、电子陷阱效应、光电子寿命、有效陷阱深度及束缚电子转移时间与增感时间的关系，获得了最佳的增感时间、衰减时间、电子陷阱效应、光电子寿命、有效陷阱深度和转移时间数值，     

纳米硫化铅增感的溴化银微晶中光电子衰减特性研究

采用纳米硫化铅作为增感剂对边长为0.8μm的溴化银立方体颗粒进行了化学增感．利用微弱信号的微波吸收相敏检测技术，在超短脉冲激光作用下，获得了立方体溴化银乳剂中自由光电子和浅束缚光电子随增感时间变化的衰减曲线。通过测量溴化银光作用过程的时间分辨谱，讨论了卤化银晶体中电子陷阱对光电子运动行为的影响，分析了电子陷阱效应同增感时间之间的关系以及两个一级衰减区间寿命值同增感时间的关系．通过未增感样品与增感样品的衰减曲线对比，得到了在此实验奈件下的最佳增感时间为60min．     

溴碘化银核壳乳剂中电子的捕获和复合

本文应用双注仪制备了在核表面进行不同程度还原增感和一系列溴碘化银核壳乳剂，在没条件下测定了核表面形成的不同还原增感中心对乳剂微晶光电子衰减动力学及发光光谱的影响。结果表明：在一定增感温度和时间条件下，当Ｎａ２ＳＯ３用量低于５．４ｍｇ／ｍｏｌＡｇ时光电子衰减动力学为二级反应，而当Ｎａ２ＳＯ３用量超过２７ｍｇ／ｍｏｌＡｇ时，增感中心一部分作为穴陷阱，另一部分作为电子陷阱，光电子衰减速率决定了电子的捕获     

S+Au增感对AgBrI T-颗粒乳剂中光电子衰减行为的影响

利用35ps脉冲激光发源,采用微波吸收介电谱检测技术,获得了S+Au增感后的AgBrI-T颗粒微晶中光电子衰减时间分辨谱,通过分析自由光电子和浅束缚光电子衰减曲线的变化,得到了S+Au增感的不同时间与AgBrI-T颗粒乳剂自由光电子寿命和衰减时间及浅束缚光电子衰减时间的对应关系,给出最佳增感时间。     

卤化银微晶中浅电子陷阱的阈值效应

依据描述卤化银微晶中光生载流子的微观动力学过程的基本模型 ,分析了自由光电子衰减时间随浅电子陷阱深度和密度的变化情况 ,从而对浅电子陷阱的阈值效应进行了讨论 ,给出了确定卤化银乳剂中浅电子陷阱最佳掺杂条件的依据。     

温度条件对光谱增感AgCl晶体光电子特性的影响

利用微波吸收相敏技术检测了光谱增感AgCl立方体乳剂的光电子时间分辨谱,增感样品由于染料吸附引起填隙银离子浓度增加,其光电子衰减比未增感的要快。通过分析增感温度条件与光电子特性的关系,发现温度条件影响了染料吸附程度,进而影响了光电子的衰减特性。温度为45℃时,晶体受染料吸附的影响最大,光电子衰减最快。低于或高于此温度时染料吸附不充分或存在生成大聚集体的趋势,引起晶体填隙银离子浓度的变化较小,光电子衰减较慢。     

光谱增感AgBrI-T颗粒乳剂光电子特性

用微波吸收相敏技术检测了光谱增感AgBrI T颗粒乳剂的自由光电子时间分辨谱 ,观察到增感样品在染料增感吸收峰位置有明显的光电子信号 ,在AgBrI T颗粒固有吸收带自由光电子衰减时间比未增感样品的衰减时间短。     

Insect antifeedant properties of anthranoids from the genusVismia

Vismiones and ferruginins, representatives of a new class of lypophilic anthranoids from the genusVismia were found to inhibit feeding in larvae of species ofSpodoptera, Heliothis, and inLocusta migratoria.     

Direct observation of freeze-thaw instability of latex coatings via high pressure freezing and cryogenic SEM

Despite its industrial importance, the subject of freeze-thaw (F/T) stability of latex coatings has not been studied extensively. There is also a lack of fundamental understanding about the process and the mechanisms through which a coating becomes destabilized. High pressure (2100 bar) freezing fixes the state of water-suspended particles of polymer binder and inorganic pigments without the growth of ice crystals during freezing that produce artifacts in direct imaging scanning electron microscopy (SEM) of fracture surfaces of frozen coatings. We show that by incorporating copolymerizable functional monomers, it is possible to achieve F/T stability in polymer latexes and in low-VOC paints, as judged by the microstructures revealed by the cryogenic SEM technique. Particle coalescence as well as pigment segregation in F/T unstable systems are visualized. In order to achieve F/T stability in paints, latex particles must not flocculate and should provide protection to inorganic pigment and extender particles. Because of the unique capabilities of the cryogenic SEM, we are able to separate the effects of freezing and thawing, and study the influence of the rate of freezing and thawing on F/T stability. Destabilization can be caused by either freezing or thawing. A slow freezing process is more detrimental to F/T stability than a fast freezing process; the latter actually preserves suspension stability during freezing. Presented at the 82nd Annual Meeting of the Federation of Societies for Coatings Technology, October 27–29, 2004 in Chicago, IL. Tied for first place in The John A. Gordon Best Paper Competition.     

Ethanol and (−)-α-Pinene: Attractant Kairomones for Bark and Ambrosia Beetles in the Southeastern US

In 2002–2004, we examined the flight responses of 49 species of native and exotic bark and ambrosia beetles (Coleoptera: Scolytidae and Platypodidae) to traps baited with ethanol and/or (−)-α-pinene in the southeastern US. Eight field trials were conducted in mature pine stands in Alabama, Florida, Georgia, North Carolina, and South Carolina. Funnel traps baited with ethanol lures (release rate, about 0.6 g/day at 25–28°C) were attractive to ten species of ambrosia beetles (Ambrosiodmus tachygraphus, Anisandrus sayi, Dryoxylon onoharaensum, Monarthrum mali, Xyleborinus saxesenii, Xyleborus affinis, Xyleborus ferrugineus, Xylosandrus compactus, Xylosandrus crassiusculus, and Xylosandrus germanus) and two species of bark beetles (Cryptocarenus heveae and Hypothenemus sp.). Traps baited with (−)-α-pinene lures (release rate, 2–6 g/day at 25–28°C) were attractive to five bark beetle species (Dendroctonus terebrans, Hylastes porculus, Hylastes salebrosus, Hylastes tenuis, and Ips grandicollis) and one platypodid ambrosia beetle species (Myoplatypus flavicornis). Ethanol enhanced responses of some species (Xyleborus pubescens, H. porculus, H. salebrosus, H. tenuis, and Pityophthorus cariniceps) to traps baited with (−)-α-pinene in some locations. (−)-α-Pinene interrupted the response of some ambrosia beetle species to traps baited with ethanol, but only the response of D. onoharaensum was interrupted consistently at most locations. Of 23 species of ambrosia beetles captured in our field trials, nine were exotic and accounted for 70–97% of total catches of ambrosia beetles. Our results provide support for the continued use of separate traps baited with ethanol alone and ethanol with (−)-α-pinene to detect and monitor common bark and ambrosia beetles from the southeastern region of the US.     

Methyl 2,4,6-decatrienoates Attract Stink Bugs and Tachinid Parasitoids

Halyomorpha halys (Stål) (Pentatomidae), called the brown marmorated stink bug (BMSB), is a newly invasive species in the eastern USA that is rapidly spreading from the original point of establishment in Allentown, PA. In its native range, the BMSB is reportedly attracted to methyl (E,E,Z)-2,4,6-decatrienoate, the male-produced pheromone of another pentatomid common in eastern Asia, Plautia stali Scott. In North America, Thyanta spp. are the only pentatomids known to produce methyl 2,4,6-decatrienoate [the (E,Z,Z)-isomer] as part of their pheromones. Methyl 2,4,6-decatrienoates were field-tested in Maryland to monitor the spread of the BMSB and to explore the possibility that Thyanta spp. are an alternate host for parasitic tachinid flies that use stink bug pheromones as host-finding kairomones. Here we report the first captures of adult and nymph BMSBs in traps baited with methyl (E,E,Z)-2,4,6-decatrienoate in central Maryland and present data verifying that the tachinid, Euclytia flava (Townsend), exploits methyl (E,Z,Z)-2,4,6-decatrienoate as a kairomone. We also report the unexpected finding that various isomers of methyl 2,4,6-decatrienoate attract Acrosternum hilare (Say), although this bug apparently does not produce methyl decatrienoates. Other stink bugs and tachinids native to North America were also attracted to methyl 2,4,6-decatrienoates. These data indicate there are Heteroptera in North America in addition to Thyanta spp. that probably use methyl 2,4,6-decatrienoates as pheromones. The evidence that some pentatomids exploit the pheromones of other true bugs as kairomones to find food or to congregate as a passive defense against tachinid parasitism is discussed.     

2007～2008年世界塑料工业进展

收集了2007年7月～2008年6月世界塑料工业的相关资料,介绍了2007～2008年国外塑料工业的发展情况,提供了世界塑料产量、消费量及全球各类树脂的需求量及产能情况.按通用热塑性树脂(聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂)、工程塑料(尼龙、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚)、特种工程塑料(聚苯·硫醚、液晶聚合物、聚醚醚酮)、通用热固性树脂(酚醛、聚氨酯、不饱和聚酯树脂、环氧树脂)不同品种的顺序,对树脂的产量、消费量、供需状况及合成工艺、产品应用开发、树脂品种的延伸及应用的进一步扩展等技术作了详细介绍.     

2005～2006年国外塑料工业进展

收集了2005年7月～2006年6月国外塑料工业的相关资料,介绍了2005—2006年国外塑料工业的发展情况。提供了世界塑料产量、消费量及全球各类树脂生产量以及各国塑料制品的进出口情况。作为对比,介绍了中国塑料的生产情况。按通用热塑性树脂（聚乙烯、聚丙烯、聚苯乙烯、聚氯乙烯、ABS树脂）、工程塑料（聚酰胺、聚碳酸酯、聚甲醛、热塑性聚酯、聚苯醚）、通用热固性树脂（酚醛、聚氨酯、不饱和树脂、环氧树脂）、特种工程塑料（聚苯硫醚、液晶聚合物、聚醚醚酮）的品种顺序,对树脂的产量、消费量、供需状况及合成工艺、产品开发、树脂品种的延伸及应用的扩展作了详细的介绍。