以碳酸氢铵为沉淀剂制备纳米氧化锌粉体

以硫酸锌、碳酸氢铵为主要原料，采用直接沉淀法制备出纳米氧化锌粉体。对前驱体进行DSC-TG分析，对煅烧样品进行x射线衍射（XRD）分析，利用谢乐公式计算晶粒度。结果显示，前驱体在300℃时基本分解完毕；550℃煅烧可制备出结晶良好、35-45nm的氧化锌粉体；提高沉淀反应的温度能降低纳米ZnO粉体的粒度。     

纳米氧化锌的制备及抗菌性能研究

目的 研究以乙酸锌和氢氧化钠为原料,利用水热合成法制备纳米氧化锌的最佳工艺条件及抗菌性能。方法 以纳米氧化锌的粒径和形貌为评价指标,讨论合成条件对产物的影响;基于单因素设计响应面实验,以抑菌圈直径为响应值,分析抑菌效果较好的纳米氧化锌的制备条件。结果 在水热温度为111.14 ℃,反应时间为10 h,乙酸锌浓度为0.02 mol/L时制备的纳米氧化锌的抗菌效果最好,大肠杆菌的抑菌圈直径为（17.265±0.011）mm。结论 水热温度、水热时间和前驱体浓度会影响纳米氧化锌的粒径和形貌;水热温度和前驱体浓度是影响纳米氧化锌抑菌性的显著因素,水热时间是非显著因素。     

聚乙烯醇为助剂水热法制备氧化锌纳米棒

一维结构的纳米氧化锌具有独特的电子和光电性能,在众多领域有着广阔的应用前景,故而对其合成方法的研究十分重要.本文中以聚乙烯醇作为修饰剂,通过水热法在较低的反应温度下制备了一维氧化锌纳米棒.分别用透射电镜、选区电子衍射和X射线衍射对产物形貌与结构进行了表征.研究发现,以聚乙烯醇为助剂在120℃反应24h可制备出具有六方结构的氧化锌纳米棒,其直径为50～80nm、长度为1～2μm.实验表明,聚乙烯醇在一维结构合成过程中起到关键作用,以Zn(0H)2为水热反应前驱体可制备出品质较高的一维氧化锌纳米棒.     

纳米氧化锌的制备

以硫酸锌和碳酸铵为原料,直接沉淀法制得纳米氧化锌的前驱体,然后煅烧得到纳米氧化锌.采用 TG-DTG、XRD和TEM等测试手段对其进行了表征.结果表明,前驱体为Zn4(OH)6CO3.通过控制煅烧温度、反应温度和反应物浓度可以得到不同粒径的球形纳米氧化锌.得出了最佳制备工艺条件.     

不同形貌Ti-O基纳米结构的可控制备与形成机制探讨

利用碱辅助水热法实现了Ti-O基纳米管、纳米带和纳米结构微球的合成,通过TEM、SEM等手段对所制备的纳米结构进行表征。当采用商品级锐钛矿TiO2为原料,热水处理温度为180℃、碱的浓度为10mol/L,热处理48h时可以得到Ti-O基纳米带。纳米带宽度为50~200nm,长度达到几十微米甚至一百多微米;产物产率高,质量好,结晶良好,表面洁净,无缺陷。当热处理温度为120℃时,可以得到Ti-O基纳米管,纳米管的长度为200~500nm,外径在20~50nm之间。当所用前驱体的粒径较小时,容易形成较细或者较窄的纳米带或者纳米线,当在选用前驱体的粒径较大时,可以生成纳米结构微球。     

醇-水体系无表面活性剂纳米ZnO的制备及表征

以乙酸锌为前驱物,乙醇、正丙醇和正丁醇为溶剂,不加入表面活性剂,通过改变反应体系中醇水体积比、pH值、前驱物浓度,在反应温度80℃、反应时间30 min的条件下,制备得到不同尺寸和形貌的纳米氧化锌粒子.通过透射电子显微镜(TEM)、X射线衍射和紫外-可见吸收光谱等方法对纳米氧化锌进行了表征.结果表明:所合成的纳米氧化锌样品在350～365 nm范围内具有较为明显的吸收峰,减小醇水体积比、减弱溶剂极性、增加前驱物乙酸锌浓度,均可以导致纳米氧化锌粒子尺寸变大、团聚加重,前驱物溶液pH值的改变对纳米氧化锌的吸收峰影响不大.     

纳米氧化锌的制备工艺研究

以均匀沉淀法作为纳米氧化锌的制备方法,通过单因素实验和正交实验,系统地分析了溶液水解反应温度、水解反应时间、原料摩尔配比、煅烧温度等对氧化锌粉体产率和粒径的影响。结果表明,最佳工艺是:以直接混合的方式混合原料液,聚乙二醇-400作表面活性剂,反应温度90℃,原料摩尔配比c(尿素)/c(硝酸锌)=3:1,反应时间5.5h,前驱体碱式碳酸锌的最佳煅烧温度为500℃。通过所制得纳米氧化锌的XRD、SEM的粒径分析,证明了所制得的纳米氧化锌晶形为六方晶相,纯度大于99.9%、平均粒径约为68nm,产率为89.6%。     

前驱体反应温度对CeO2粉体抛光性能的影响

以CeCl3为铈源,Na2CO3为沉淀剂,采用沉淀法在不同反应温度下制备CeO2前驱体,焙烧前驱体制备CeO2粉体,研究前驱体反应温度对产物组成、结构、形貌及抛光性能的影响。结果表明,当反应温度低于或高于50℃时,前驱体分别以Ce2(CO3)3·8H2O或CeCO3OH为主;反应温度对由2种前驱体制备的CeO2粉体的抛光性能影响较大,当前驱体反应温度为45~50℃时,制备的CeO2粉体粒度均匀,抛光性能最优。     

钛酸盐一维纳米材料向TiO2纳米材料的水热转化研究

采用强碱性水热处理法分别控制第一次水热反应为160℃和200℃,制备出一维纳米管和纳米棒2种形貌的产物,将其作为第二次水热反应的前驱体,考察了第二次水热体系中pH值和温度对TiO2纳米材料的晶相组成及其微观形貌的影响;采用XRD、TEM以及HRTEM对样品进行了分析.结果表明,当以纳米管为前驱体时,除在pH=0的体系中得到了以金红石相为主的单晶纳米棒外,在pH值为2、4和7的条件下均得到了单晶纯锐钛矿相TiO2纳米颗粒.当以纳米棒为前驱体时,在pH=0的体系中得到了金红石相与板钛矿相共存的纳米棒和纳米颗粒混合产物;在pH值为2、4和7的条件下均得到了纯锐钛矿相TiO2纳米棒;当二次水热温度低于180℃时,前驱体没有转化完全,所得产物为前驱体与锐钛矿相TiO2共存的纳米棒;当水热温度为180℃和210℃时,产物为纯锐钛矿相纳米棒.     

纳米氧化锌-煅烧高岭土复合材料的制备

以煅烧高岭土和纳米氧化锌为主要原料,用水解沉淀法在煅烧高岭土表面包覆纳米氧化锌,制备一种无机复合型抗紫外材料;采用分光光度计分别测定在波长325、350、375、400nm紫外光下复合材料的紫外光吸光度。结果表明:反应温度、氧化锌包覆量、改性时间、改性剂滴加速度、矿浆浓度、煅烧温度等对纳米氧化锌-煅烧高岭土复合粉体材料的紫外光吸收性能有重要影响。在制备条件为:氧化锌包覆量为8%、反应温度为90℃、改性时间为10min、改性剂滴加速度为3mL/min、矿浆中m(水)∶m(煅烧高岭土)=10∶1、煅烧温度为400℃时,所制备的纳米氧化锌-煅烧高岭土复合粉体材料的紫外光吸收性能较好。     

凝固科学技术与材料

从凝固科学与实践发展的角度介绍了当前凝固材料体系的基本框架和凝固科学主要发展阶段的基本理论。作为材料科学与工程的基本组成，凝固科学技术正在现代科学理论的基础上针对传统材料的改性提高和新材料的发展需求，以控形、控构、控性为目标开展优质铸件的定向、晶体生长、快凝、深过冷及各种新型和超常领域凝固过程的研究，并介绍了其中某些方面和展望了可能的发展趋势。     

Development and challenges of planning and scheduling for petroleum and petrochemical production

Production planning and scheduling are becoming the core of production management, which support the decision of a petrochemical company. The optimization of production planning and scheduling is attempted by every refinery because it gains additional profit and stabilizes the daily production. The optimization problem considered in industry and academic research is of different levels of realism and complexity, thus increasing the gap. Operation research with mathematical programming is a conventional approach used to address the planning and scheduling problem. Additionally, modeling the processes, objectives, and constraints and developing the optimization algorithms are significant for industry and research. This paper introduces the perspective of production planning and scheduling from the development viewpoint.     

江澳两地高校文创设计的协同研究与商业实践

目的 探索江门世遗文化的传承、发展和转化的新思路,践行国家在《粤港澳大湾区发展规划》纲要中要求江门承担与港澳地区文化创意合作与开发任务的分工。方法 与澳门高校紧密合作,开展专业培训课程,以开平碉楼为例,从人文视角开展设计研究,梳理开平碉楼的文化脉络,把世遗文化的元素和其背后的文化融入文创产品中,提升文创产品的附加值,推动当地文创产业结构的变革。结果 两地高校构建了稳定的科研团队,开设长期有效的设计培训课程,与景区建立了研究协作关系,帮助景区构建了一套产销研的商业模式。结论 以跨区域高校合作为平台,以文创产品为抓手,依托江澳两地的资源优势,可以构建江门世遗文化全新的品牌形象,最终推动开平世遗文化的活化。     

Error and uncertainty in modeling and simulation

This article develops a general framework for identifying error and uncertainty in computational simulations that deal with the numerical solution of a set of partial differential equations (PDEs). A comprehensive, new view of the general phases of modeling and simulation is proposed, consisting of the following phases: conceptual modeling of the physical system, mathematical modeling of the conceptual model, discretization and algorithm selection for the mathematical model, computer programming of the discrete model, numerical solution of the computer program model, and representation of the numerical solution. Our view incorporates the modeling and simulation phases that are recognized in the systems engineering and operations research communities, but it adds phases that are specific to the numerical solution of PDEs. In each of these phases, general sources of uncertainty, both aleatory and epistemic, and error are identified. Our general framework is applicable to any numerical discretization procedure for solving ODEs or PDEs. To demonstrate this framework, we describe a system-level example: the flight of an unguided, rocket-boosted, aircraft-launched missile. This example is discussed in detail at each of the six phases of modeling and simulation. Two alternative models of the flight dynamics are considered, along with aleatory uncertainty of the initial mass of the missile and epistemic uncertainty in the thrust of the rocket motor. We also investigate the interaction of modeling uncertainties and numerical integration error in the solution of the ordinary differential equations for the flight dynamics.     

Density and viscosity of tetralin and trans-decalin

New measurements are reported for the density and viscosity of tetralin and trans-decalin. The density was determined from room temperature to 60°C for tetralin and to 95°C for trans-decalin. The kinematic viscosity was measured up to temperatures slightly above 100°C. Our results improve upon the values recommended by the American Petroleum Institute for these liquids.     

Creation and motion of dislocations and fracture in metal and silicon crystals

By making a step on one surface ( ) of a rectangular small paralellepiped copper crystal, dislocations could be created by the molecular dynamic method. The dislocation created was not a complete edge dislocation but a pair of Heidenreich-Shockley partial dislocations. Each time a dislocation was created, the stress on the surface was released. Small copper crystals having a notch were pulled (until fracture), compressed and buckled by use of the molecular dynamic method. An embedded atom potential was used to represent the interaction between atoms. Dislocations were created near the tip of the notch. A very sharp yield stress was observed. The results of high speed deformations of pure silicon small crystals using the molecular dynamics are presented. The results suggest that plastic deformation may be possible for the silicon with a high speed deformation even at room temperature. Another small size single crystal, the same size and the same surfaces, was compressed using molecular dynamic method. The surfaces are {110}, {112} and {111}. The compressed direction was [111]. It was found that silicon crystals are possible to be compressed with a high speed deformation. This may suggest that silicon may be plastically deformed with high speed deformation.     

SMC／BMC的回收与再利用

SMC／BMC废弃物对工业及环境造成了很大影响，指出了SMC／BMC回收再利用的紧迫性。通过对目前国际上SMC／BMC回收再利用的3种典型途径优缺点的对比，参照国外SMC／BMC回收再利用的先进方法，对我国SMC／BMC回收再利用提供了可行的建议．     

The Candela and Photometric and Radiometric Measurements

The national measurement system for photometric and radiometric quantities is presently based upon techniques that make these quantities traceable to a high-accuracy cryogenic radiometer. The redefinition of the candela in 1979 provided the opportunity for national measurement laboratories to base their photometric measurements on optical detector technology rather than on the emission from high-temperature blackbody optical sources. The ensuing technical developments of the past 20 years, including the significant improvements in cryogenic radiometer performance, have provided the opportunity to place the fundamental maintenance of photometric quantities upon absolute detector based technology as was allowed by the 1979 redefinition. Additionally, the development of improved photodetectors has had a significant impact on the methodology in most of the radiometric measurement areas. This paper will review the status of the NIST implementation of the technical changes mandated by the 1979 redefinition of the candela and its effect upon the maintenance and dissemination of optical radiation measurements.