SmCo6.6Nb0．4块状纳米晶烧结磁体的结构和磁性能

采用SPS技术制备了纳米晶SmCo6．6Nb0.4烧结磁体，研究了磁体的结构和磁性能．X衍射结果表．4明烧结磁体具有TbCu7结构，说明SPS过程可以获得稳定的1：7相．TEM观察显示，磁体由平均晶粒尺寸约为30nm的1：7相构成．室温时磁体的矫顽力高达2．8T，而剩磁比高达0．74，说明在纳米晶之间存在强烈的晶间交换耦合作用．烧结磁体具有良好的高温性能，矫顽力温度系数β为-0.169％/K。     

SmCo7块状纳米晶烧结磁体的制备和性能

采用放电等离子烧结技术制备了致密纳米晶SmCo6.6Nb0.4烧结磁体,研究了磁体的结构和磁性能.结果表明,烧结磁体具有TbCu7结构,说明通过SPS过程可以获得稳定的1:7相;磁体由平均晶粒尺寸约为30 nm的1:7相构成,磁体的室温矫顽力高达2.8 T,而剩磁比高达0.74,说明在纳米晶之间存在强烈的晶间交换耦合作用.烧结磁体具有良好的高温性能,773K时的矫顽力为0.48 T,矫顽力温度系数β为-0.169%/K.     

SmCo7-xFex块状纳米晶烧结磁体的研究

采用放电等离子烧结技术制备了块状纳米晶SmCo7-xFex（x=0，0．4，1，2）烧结磁体，对磁体的微观结构扣磁性能进行了观察扣测试．X衍射结果表明，烧结磁体具有TbCu7结构，说明SPS过程可以获得稳定的1：7相．TEM观察显示，磁体晶粒尺寸在20～50nm．磁体具有较好的磁性能，x=0．4时，矫顽力为992．8kA/m，剩磁为0．634T（BH）max为69．75kJ/m^3。     

块状纳米晶Sm2Co17烧结磁体的研究

采用高能球磨和放电等离子烧结技术制备了致密纳米晶Sm2Co17烧结磁体,研究了粉末和烧结磁体的结构和磁性能.球磨粉末在低温退火(<1023K)时,主相为TbCu7结构;高温退火(>1023K)时,主相为Th2Zn17结构.退火温度从923K增加到1223K,粉末的矫顽力从0.99T下降到0.12T.烧结磁体也具有TbCu7结构,磁体平均晶粒尺寸约为35nm.室温时磁体的剩磁为0.65T,矫顽力达0.87T.烧结磁体具有较好的高温性能,573K时的剩磁为0.6T,矫顽力为0.32T.     

回收制备烧结Nd-Fe-B磁体的磁性能与耐热性能

以废旧钕铁硼磁体为原料,采用短流程回收制备技术制备了烧结Nd-Fe-B磁体,通过添加镨钕混合稀土研究了磁体的磁性能和耐热性能。结果表明,在回收磁体中添加2%PrNd,制备的烧结Nd-Fe-B磁体的剩磁为1.31T、矫顽力为1 474.86kA/m、磁能积为353.90kJ/m~3。与一次成品相比矫顽力恢复到102%,剩磁恢复到95%,磁能积恢复到90%。在293~393K范围内未掺杂PrNd磁体的矫顽力温度系数为-0.589 9%/K,掺杂2%PrNd磁体的矫顽力温度系数为-0.556 4%/K,提高了磁体在高温下的耐热性能。这是由于添加混合稀土PrNd增强了主相晶粒间的去磁交换耦合作用,提高了主相的磁晶各向异性场,从而提高了磁体的矫顽力和耐热性能。     

回收制备烧结Nd-Fe-B磁体的磁性能与耐热性能

以废旧钕铁硼磁体为原料,采用短流程回收制备技术制备了烧结Nd-Fe-B磁体,通过添加镨钕混合稀土研究了磁体的磁性能和耐热性能.结果表明,在回收磁体中添加2％ PrNd,制备的烧结Nd-Fe-B磁体的剩磁为1.31T、矫顽力为1 474.86 kA/m、磁能积为353.90 kJ/m3.与一次成品相比矫顽力恢复到102％,剩磁恢复到95％,磁能积恢复到90％.在293～393 K范围内未掺杂PrNd磁体的矫顽力温度系数为-0.589 9％/K,掺杂2％PrNd磁体的矫顽力温度系数为-0.556 4％/K,提高了磁体在高温下的耐热性能.这是由于添加混合稀土PrNd增强了主相晶粒间的去磁交换耦合作用,提高了主相的磁晶各向异性场,从而提高了磁体的矫顽力和耐热性能.     

Sm(Co_(0.74)Cu_(0.12)Fe_(0.1)Zr_(0.04))_(7.5)纳米晶烧结磁体的结构和磁性能

采用放电等离子烧结技术制备了致密纳米晶SmCoCuFeZr烧结磁体,研究了磁体的结构和磁性能.X衍射结果表明,烧结磁体具有TbCu_7结构.TEM观察显示,烧结磁体平均晶粒尺寸为35nm.室温时磁体的剩磁为0.49T,矫顽力高达1.42T,而剩磁比Mr/Ms为0.63,表明在纳米晶之间存在晶间交换耦合作用.     

NdH纳米助剂回收制备烧结钕铁硼永磁体的研究

采用NdH纳米掺杂的方法对废旧烧结钕铁硼磁体进行了回收制备。研究了不同NdH纳米粉掺杂量对再制造烧结钕铁硼磁性能的影响。随着NdH纳米粉末掺杂量的增多,烧结磁体矫顽力从926.54 kA/m增加到1 299.87 kA/m;剩磁首先相对稳定在1.296 T,在掺杂量2.0%(质量分数)后,剩磁逐渐下降。与原始磁体相比,2.0%(质量分数)NdH纳米粉掺杂磁体性能最佳,矫顽力回复97.5%,剩磁回复95.9%,磁能积回复89.7%。通过计算,掺杂3.0%(质量分数)NdH纳米粉后,再制造烧结磁体中富钕相体积分数从3.03%增加到5.70%,然而其晶粒尺寸从8.18μm增长至11.68μm。结合微观分析与磁性能,2.0%(质量分数)NdH纳米粉掺杂磁体性能最好。     

采用SC工艺制备高性能烧结钕铁硼磁体的研究

研究了采用SC(strip casting)工艺制备的高性能烧结钕铁硼磁体。结果表明：速凝薄带主要由厚度约3μm的(2：14：1)相片状晶组成．片状晶之间被厚度0．2～0．5μm的富Nd相薄层隔开，没有α-Fe枝状晶存在。速凝薄带经氢破碎、气流磨、压型、烧结后磁体的永磁性能达到：Br=1．431T，jHe=1022kA／m，(BH)max=387kJ／m3。     

放电等离子烧结NdFeB磁体的磁化特征

利用放电等离子烧结技术(SPS)制备烧结钕铁硼磁体SPS NdFeB。为了更好地理解SPS Nd-FeB磁体的磁硬化机理,利用振动样品磁强计研究了SPS NdFeB磁体在室温下的磁化和反磁化过程。结果表明,在强度为800kA/m的较低外加磁场和强度为1760kA/m的较高外加磁场下的磁化特征明显不同,前者可称为形核控制模式,后者则为钉扎控制模式。比较样品的磁化过程和反磁化过程的曲线,发现样品的矫顽力大小等于样品磁化过程钉扎场的大小。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Synthesis of Alumina-Zirconia Nanocomposites by Solgel Process

Al₂O₃-ZrO₂ nanocomposites were developed starting with the solgel process. Composite alumina-zirconia nanopowders were synthesized from metallorganic precursors (Aluminium secondary butoxide and zirconium Iso propoxide) using the solgel process. The parameters affecting the synthesis—solvent, concentration of precursor, R/H ratio (i.e., dilution of water in solvent)—were varied as also the temperature and pH. BET and TEM were used to measure nanosize. Diffuse reflectance spectroscopy and also qualitative optical absorption led to identical particle size estimate. The variation of process parameters was used to study the effect and interdependence of process parameters. Artificial Neural Networks was used to rigorously analyze the process. Although this led to confirmation of interdependence of parameters, the presence of a single overwhelming solvent variable was also established. Then the optimal process was used to synthesize more nanopowder. To produce bulk nanocomposite the nanopowders were sintered by varying the temperature and time period. The sintered lithoids were probed with a vickers hardness tester to measure elastic modulus, hardness, and fracture toughness. The results showed high elastic modulus, modest hardness, and very high fracture toughness.