FEP和多孔PTFE复合膜铁电驻极体的压电性及电荷动态特性

报道了将致密的FEP和多孔PTFE交互层叠在一起，采用热粘合的方法制备出具有孔洞结构的聚合物复合膜，然后经电晕极化处理使该复合膜成为铁电驻极体。最后用准静态方法测量该铁电复合膜的压电系数d33，并通过热刺激电流放电（TSD）电流谱和等温衰减研究了FEP和多孔PTFE复合膜铁电驻极体的电荷动态特性。结果表明：该复合膜的压电系数d33可达200～500pC/N，在0～12kPa的压强范围内呈现出良好的线性，并且在90℃下老化160min后仍保持在原来的43％且趋于稳定；FEP和多孔PTFE复合膜铁电驻极体电荷在热激发脱阱后复合途径主要有2种：一种是沿着固体介质的表面迁移与异性电荷复合，另一种是穿过固体介质层与异性电荷复合。在低温区（7512附近）前者占优，高温区（120℃附近）后者占优。     

辐照交联聚丙烯压电功能膜的机电性能

研究了基于辐照交联聚丙烯（XPP）的压电驻极体功能膜的机电性能。利用介电谐振谱测定了XPP膜的弹性模量;通过准静态方法测量了该功能膜的压电系数d33及其压强特性曲线;对压电相应的时域谱进行了分析;最后讨论了该功能膜的力学疲劳特性。结果表明XPP压电驻极体膜的弹性模量为1.3MPa,压电系数d33在10～100kPa的压强范围内都具有良好的线性度;时域谱揭示了XPP膜的粘流特性;XPP膜的输出电压和压力呈现良好的线性关系;经历60万次的循环力载荷,压电系数d33没有明显的变化。     

单层及多层PP蜂窝膜驻极体的压电性

经压力膨化处理后,以正逆压电系数d33测量研究了一种经无栅电晕充电的国产商用聚丙烯蜂窝膜(cellular PP,商品名PQ50)驻极体的压电性.经过优化工艺参数压力膨化处理后的PQ50蜂窝膜呈现600pC/N以上的准静态压电系数,这一量值约为PVDF相关系数的40倍.而通过将单层PQ50蜂窝膜驻极体粘贴形成合理的多层结构,得到的复合膜系压电系数d33高达2010pC/N,约为PZT压电陶瓷相应系数的3倍.从而为拓宽这类新一代的非极性孔洞聚合物压电功能膜应用领域,推动其应用进程提供了一定的理论和技术依据.     

孔洞结构聚丙烯铁电驻极体薄膜的压电性研究

为了提高孔洞结构聚丙烯(cellular PP)铁电驻极体的压电性能,采用高压气体膨化技术对材料进行了改性处理,并利用准静态和干涉仪测量方法,对经处理的cellular PP铁电驻极体薄膜的压电效应进行了研究.结果表明:气体膨化工艺能够明显提高cellular PP铁电驻极体薄膜的压电活性:这种突出的压电活性源干膨化膜杨氏模量Y的降低和电极化能力的提高;压电系数d33随频率的增加呈现下降趋势:从0.01 Hz下的1200 pC/N降低到共振频率附近的350 pC/N;对于不同参数处理的样品,它们的共振频率在150～400 kHz;大多数样品的d33在0.2～10 kPa的范围内没有明显的变化,但是高于10 kPa,d33随之下降;cellular PP铁电驻极体薄膜d33的热稳定性与非孔洞型PP驻极体薄膜的电荷储存热稳定性相当.     

微结构PDMS压电俘能器设计与特性研究

设计了一种具有三明治结构的微结构驻极体膜,采用旋涂、"软刻蚀"等工艺,结合氧等离子体键合、恒压电晕放电技术,以铜网作为电极,摸索出完整的工艺流程,制作了基于微结构PDMS驻极体的柔性压电俘能器。测量了驻极体膜的压电系数以及力-电特性。结果显示,微结构PDMS压电俘能器的压电系数(d33)为25pC/N;在5N周期性压力下,最大能够产生1.98Vpp的开路电压;驻极体膜的谐振频率为32Hz,且产生的电压与受到的压力呈线性关系。     

聚丙烯孔洞型铁电驻极体薄膜的压电性研究

利用准静态法和激光干涉法测量正、逆压电d33系数,研究了经压力膨化处理的聚丙烯孔洞型铁电驻极体薄膜压电系数的压强和频率特性及其热稳定性.结果表明,聚丙烯薄膜经压力膨化处理后,其压电性能改善的原因是:压力膨化处理既能有效地降低孔洞膜的弹性模量Y,又能增强其储电能力.聚丙烯孔洞膜的压电d33系数在激励信号压强为0.2～4kPa的范围内基本保持恒定,但当其值高于4kPa时,d33系数出现了明显的下降.聚丙烯孔洞膜的压电d33系数随频率上升而下降(即从0.001Hz时的1200pC/N降低到其机械共振频率附近时的350pC/N),是与材料的弹性模量Y随频率的上升而增加直接相关.对不同工艺参数制备的样品,其机械共振频率位于150～400kHz范围内.实验结果还表明:聚丙烯孔洞膜的压电d33系数的热稳定性与非孔洞型聚丙烯驻极体薄膜的电荷储存热稳定性相近.     

温度和湿度对聚四氟乙烯多孔驻极体膜压电活性稳定性的影响

研究了具有开放性孔洞的聚四氟乙烯(voided polytetrafluoroethylene,PTFE)多孔膜和PP蜂窝膜(polypropylene cellular)的驻极体行为和压电活性的温度效应。研究结果指出：和PP蜂窝膜驻极体相比．PTFE多孔膜驻极体呈现出突出的电荷储存和压电活性的温度稳定性;研究了这类稳定性的驻极体和材料的结构根源。PTFE多孔薄膜驻板体这种压电活性的温度稳定性主要依赖于这类驻极体材料电荷储存及材料的本征性能(如力学性质等)的温度稳定性。实验结果还说明：PTFE多孔膜突出的压电系数温度稳定性使它大大扩展了以包括PP在内的空间电荷型多孔膜研制的压电功能元器件的耐温要求。本文还讨论了环境因素(如相对湿度)对这类功能膜压电活性的影响,分析了环境湿度对压电活性影响的结构根源。     

聚合物驻极体材料研究的新进展

综述了几种电活性聚合物近年来的迅猛发展状况。其中之一是空间电荷型聚合物压电膜，例如聚丙稀蜂窝膜(PP cellular)和聚四氮乙烯多孔膜(porous PTFE)，它们呈现出高达200～600pC／N的压电d33系数。另一类是经缺陷结构修正的弛豫铁电聚合物偏氟—三氟乙烯共聚物，它们在150MV／m的电场作用下可能诱导出约5％的高应变量和1J/cm^3的高弹性能密度。而全有机复合材料则且现出十分高的介电系数(＞900)，和在13MV／m的较低电场下形成的2％的高应变量及接近1GPa的高弹性模量。     

多孔PTFE/P(VDF-HFP)复合膜的驻极体性质

通过栅控恒压负电晕充电、等温表面电位衰减测量、热刺激放电(Thermally Stimulated Discharge,TSD)电流谱分析、电荷TSD和压电d33系数测量等方法,首次研究了将旋涂在基片上的含一定溶剂的聚偏氟乙烯和六氟丙烯共聚物(P(VDF-HFP))薄膜与多孔聚四氟乙烯薄膜均匀压合形成的多孔PTFE/P(VDF-HFP)双层复合膜系的驻极体性质.从多孔PTFE面充电的双层膜具有较从P(VDF-HFP)面充电优异的多的电荷热稳定性.使用介电谐振谱测量的双层膜的压电d33系数(31pC/N)是传统的铁电聚合物材料PVDF相应值(15 pC/N)的2倍左右.     

P(VDF-TFE-HFP)/PTFE双层膜的驻极体特性

通过栅控恒压电晕充电,等温表面电位衰减测量．电荷TSD(charge TSD)和热刺激放电(Thermally Stimulated Discharge．TSD)电流谱分析,首次研究了以聚四氟乙烯(PTFE)为基的偏氟、四氟乙烯和六氟丙烯三元共聚物P(VDF—TFE—HFP)构成的双层膜的驻极体性质。TSD电流谱分析说明这种复合驻极体材料是极性驻极体,即体内同时包含有空间电荷和有序取向的偶极电荷。实验结果还指出：通过对双层膜系的PTFE面充电形成的驻极体的空间电荷热稳定性明显优于传统的铁电聚合物驻极体PVDF。适当提高充电温度和充电后的等温老化储存可以改善电荷稳定性,由于该三元共聚物的高弹性柔量(顺度)和双层膜拥有的优良电荷储存能力,其压电活性高于PVDF．     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...