Effects of aluminium nitride inclusions on thermal and electrical properties of epoxy and polypropylene: An experimental investigation

Thermal and dielectric properties of polymers reinforced with micro-sized aluminium nitride (AlN) particles have been studied. A set of epoxy–AlN composites, with filler content ranging from 0 to 25 vol% is prepared by hand lay-up technique. With similar filler loading, polypropylene -AlN composites are fabricated by compression molding technique. Density (ρ_c), effective thermal conductivity (k_eff), glass transition temperature (T_g), coefficient of thermal expansion (CTE) and dielectric constant (ε_c) of these composites are measured experimentally. The various experimental data were interpreted using appropriate theoretical models. Incorporation of AlN in both the resin increases the k_eff and T_g whereas CTE of composite decreases favourably. The dielectric constant of the composite also found to get modified with filler content. With improved thermal and modified dielectric characteristics, these AlN filled polymer composites can possibly be used for microelectronics applications.     

Electrospun nanofibre toughened carbon/epoxy composites: Effects of polyetherketone cardo (PEK-C) nanofibre diameter and interlayer thickness

Polyetherketone cardo (PEK-C) nanofibres were produced by an electrospinning technique and directly deposited on carbon fabric to improve the interlaminar fracture toughness of carbon/epoxy composites. The influences of nanofibre diameter and interlayer thickness on the Mode I delamination fracture toughness, flexure property and thermal mechanical properties of the resultant composites were examined. Considerably enhanced interlaminar fracture toughness has been achieved by interleaving PEK-C nanofibres with the weight loading as low as 0.4% (based on weight of the composite). Finer nanofibres result in more stable crack propagation and better mechanical performance under flexure loading. Composites modified by finer nanofibres maintained the glass transition temperature (T_g) of the cured resin. Increasing nanofibre interlayer thickness improved the fracture toughness but compromised the flexure performance. The T_g of the cured resin deteriorated after the thickness increased to a certain extent.     

Thermal conductive and electrical properties of polyurethane/hyperbranched poly(urea-urethane)-grafted multi-walled carbon nanotube composites

Hyperbranched poly(urea-urethane)-grafted multi-walled carbon nanotubes (HPU-MWCNTs) were incorporated in a polyurethane (PU) matrix based on poly(ethylene oxide-tetrahydrofuran) and aliphatic polyisocyanate resin as curing agent. The 9–12 nm thick HPU shell formed on the MWCNTs improved the dispersion of MWCNTs and enhanced the interfacial adhesion between the PU matrix and MWCNTs, leading to improvements in storage modulus and T_g of the composites and enhancement of the thermal stability of PU. Thus, composites with 0.5–1 wt% MWCNTs increased the thermal conductivity by about 60–70% when compared to, and retained the high electrical resistivity of, neat PU.     

Preparation and properties of hollow glass microsphere-filled epoxy-matrix composites

Hollow glass microsphere (HGM)–filled epoxy composites, with filler content ranging from 0 to 51.3 vol.%, were prepared in order to modify the dielectric properties of the epoxy. The results showed that the dielectric constant (D_k) and dielectric loss (D_f) of the composites decreased simultaneously with increasing HGM content, which was critical for the provision of superior high-frequency device performance. Other properties of the composite, such as the coefficient of thermal expansion (CTE) and the glass transition temperature (T_g), were also improved. The improvement in these properties was related to strong interaction between the HGM and epoxy, which was indicated by the formation of an interphase between the HGM and epoxy-matrix. It was unsatisfactory in this study that the thermal conductivity of the composites also decreased with HGM content. In order to obtain relatively high thermal conductivity and a low dielectric constant simultaneously, this paper suggests further adding other filler.     

Woven hybrid biocomposites: Dynamic mechanical and thermal properties

The dynamic mechanical and thermal analysis of oil palm empty fruit bunch (EFB)/woven jute fibre (J_w) reinforced epoxy hybrid composites were carried out. The storage modulus (E′) was found to decrease with temperature in all cases, and hybrid composites had showed better values of E′ at glass transition temperature (T_g) compared to EFB and epoxy. Loss modulus showed shifts in the T_g of the polymer matrix with the addition of fibre as reinforcing phase, which indicate that fibre plays an important role in case of T_g. The Tan δ peak height was minimum for jute composites and maximum for epoxy matrix. Complex modulus variations and phase behaviour of the hybrid composites was studied by Cole-Cole analysis. Thermal analysis result indicates an increase in thermal stability of EFB composite with the incorporation of woven jute fibres. Hybridization of EFB composite with J_w fibres enhanced the dynamic mechanical and thermal properties.     

The influence of carbon nanotubes on the PVC glass transition temperature

The suspension poly(vinyl chloride) with the K number 70 (PVC S-70) compound was applied as a matrix of the nanocomposite, and the multi-wall carbon nanotubes (MWCNT) in the concentration range between 0.01 wt.% and 0.05 wt.% as a nanofiller. The T_g determination was realized by means of DMTA, dielectric losses measurements and DSC measurements. In all cases the PVC matrix revealed lower T_g comparing with corresponding composites with CNTs, and a clear relationship between the frequency, CNT contain and the T_g was found. With an increase of the charging frequency an increase of T_g of about 3 °C by DMTA measurements, realized by frequencies f = 1 Hz and f = 10 Hz, and of 9 °C by f = 1000 Hz, was noted. Independent on the frequency a maximum of the T_g increase was observed by the CNT concentration of about 0.01–0.02 wt.%.     

Electromagnetic interference shielding behavior of poly(trimethylene terephthalate)/multi-walled carbon nanotube composites

Poly(trimethylene terephthalate) [PTT]/multiwalled carbon nanotube [MWCNT] composites having varying amounts of MWCNTs were fabricated with an aim to investigate the potential of such composites as an effective light weight electromagnetic interference (EMI) shielding material in the frequency range of 12.4-18 GHz (Ku-band). PTT/MWCNT composite with shielding effectiveness (SE) of 36-42 dB was obtained at 10% (w/w) MWCNT loading. Shielding mechanism was studied by resolving the total SE into absorption (SE_A) and reflection loss (SE_R). PTT/MWCNT composite showed absorption dominated shielding; thus it can be used as microwave, radar absorbing and stealth material. The effect of MWCNT loadings on electrical conductivity (σ) and dielectric properties of PTT and the correlation among conductivity, tan δ, absorption loss and reflection loss were also studied.     

Toughening and reinforcement of poly(vinylidene fluoride) nanocomposites with “bud-branched” nanotubes

Bud-branched nanotubes, fabricated by growing metal particles on the surface of multi-wall carbon nanotubes (MWCNTs), were used to prepare poly(vinylidene fluoride) (PVDF) based nanocomposites. The results of differential scanning calorimetry (DSC) showed that the introduction of the MWCNTs and bud-branched nanotubes both increased the crystallization temperature, while no significant variation of T_m (melting temperature), ΔH_c (melting enthalpy) and ΔH_m (crystallization enthalpy) occurred. The results of wide angle X-ray diffraction (WAXD) tests showed that α-phase was the dominated phase for both pure PVDF and its nanocomposites, indicating the addition of the MWCNTs and bud-branched nanotubes did not alter the crystal structures. Dynamic mechanical analysis (DMA) tests showed that bud-branched nanotubes were much more efficient in increasing storage modulus than the smooth MWCNTs. In addition, no significant variation of the T_g (glass transition temperature) was observed with the addition of MWCNTs and bud-branched nanotubes. Tensile tests showed that the introduction of MWCNTs and bud-branched nanotubes increased the modulus. However, a dramatic decrease in the fracture toughness was observed for PVDF/MWCNTs nanocomposites. For PVDF/bud-branched nanotubes nanocomposites, a significant improvement in the fracture toughness was observed compared with PVDF/MWCNTs nanocomposites.     

Study on short ramie fiber/poly(lactic acid) composites compatibilized by maleic anhydride

Short ramie fiber reinforced poly(lactic acid) (PLA) composites without and with maleic anhydride (MA) were developed. The influence of PLA-g-MA as a compatibilizer on the properties of the composites was studied. The tensile, flexural and impact strength of the composites have improvements with the addition of PLA-g-MA. The morphology of fracture surface evaluated by SEM indicates that the composites with the addition of PLA-g-MA can get better adhesion between the fiber and the matrix. And the Vicat softening temperature and the degradation temperature of the composites are increased with the addition of PLA-g-MA. However, PLA-g-MA leads the glass transition temperature (T_g) decrease according to the DSC results.     

Effect of aspect ratio on thermal conductivity of high density polyethylene/multi-walled carbon nanotubes nanocomposites

This study aims to investigate experimentally the effects of aspect ratio (length/diameter ratio) and concentration of multiwalled carbon nanotubes (MWCNTs) on thermal properties of high density polyethylene (HDPE) based composites. The aspect ratios of two types of MWCNT fillers are in the range of 200–400 and 500–3000. Composite samples were prepared by melt mixing up to weight fraction of 19% filler content, followed by a compression molding. Measurements of density, specific heat and thermal diffusivity (by modulated photothermal radiometry, PTR) were performed and effective thermal conductivities k_e of nanocomposites were calculated using these values. The results show that the composites containing MWCNTs with higher aspect ratio have higher thermal conductivities than the ones with lower aspect ratio. In terms of conductivity enhancement k_e/k_m − 1, the results indicate that MWCNTs with higher aspect ratio provide three to fourfold larger enhancement than the ones with lower aspect ratio, at low filler concentrations.     

Effects of grafted chain length on mechanical and electrical properties of nanocomposites containing polylactide-grafted carbon nanotubes

We herein report the effects of interfacial reinforcement on mechanical and electrical properties of nanocomposites based on polylactide (PLA) and multi-walled carbon nanotube (MWCNT). For this purpose, a series of MWCNTs grafted with PLA chains of various lengths (MWCNT-g-PLAs) were prepared by ring-opening polymerization of l-lactide with carboxylic acid-functionalized MWCNT (MWCNT-COOH). MWCNT-g-PLAs were then mixed with commercial PLA to obtain PLA/MWCNT-g-PLA nanocomposites with 1.0 wt.% MWCNT content. It was revealed that morphological, mechanical, and electrical properties of PLA/MWCNT-g-PLA nanocomposites were strongly dependent on the PLA chain length of MWCNT-g-PLAs. FE-SEM images exhibited that the nanocomposites containing MWCNT-g-PLA with longer PLA chain length exhibited better dispersion of MWCNTs in the PLA matrix. Initial moduli and tensile strengths of PLA/MWCNT-g-PLA composites increased with the increment of chain length of PLA grafted on MWCNTs, which attributes to the improved interfacial adhesion between the grafted PLA chains of MWCNT-g-PLA and the PLA matrix. As a result, the experimental initial modulus (2775 ± 193 MPa) of the nanocomposite including MWCNT-g-PLA with PLA chains of average molecular weight of 530 g/mol was quite close to the theoretical value (2911 MPa) predicted for the nanocomposite with perfect interfacial adhesion. Unexpectedly, electrical resistivities of PLA/MWCNT-g-PLA nanocomposites were found to increase from ∼10⁴ to ∼10¹² Ω/sq with increasing the PLA chain length of MWCNT-g-PLA, which is due to the fact that the PLA chains grafted on MWCNTs prevent the formation of the electrical conduction path of MWCNTs in the PLA matrix.     

电场诱导多壁碳纳米管有序排列对多壁碳纳米管/环氧树脂复合材料性能的影响

采用交流（AC）电场诱导法制备了多壁碳纳米管（MWCNTs）均匀分散且定向有序排列的MWCNTs/环氧树脂复合材料。采用SEM、偏振拉曼光谱等研究了电场强度、MWCNTs含量、加电时间及温度（黏度）等因素对MWCNTs定向排列的影响,讨论了MWCNTs有序排列对MWCNTs/环氧树脂复合材料电学和力学性能的影响。结果表明：MWCNTs沿电场方向有序排列;MWCNTs/环氧树脂复合材料施加AC电场后的拉曼强度明显高于未施加电场的情况;当MWCNTs含量从0wt%增加到0.025wt%时,MWCNTs/环氧树脂复合材料导电率从2.3×10^-12 S/cm增加到1.3×10^-8 S/cm,增加了约4个数量级;MWCNTs含量为2.5wt%时,MWCNTs/环氧树脂复合材料拉伸强度提高了26.3%。     

Compressive behavior of MWCNT/epoxy composite mats

Mats of vertically-aligned multiwall carbon nanotubes were grown in an thermal CVD reactor with simultaneous feed of the catalyst and carbon precursors. Mats were soaked into epoxy resin solutions without any prior chemical modification and then cured to produce composite plates of z-axis nano-reinforcement. Direct observations of the epoxy–CNT interactions at the nanoscale revealed that epoxy interacted naturally with the MWCNTs without affecting their physical characteristics, alignment, or the mat’s morphology. The compressive behavior of the pristine and composite mats was consistent with mechanical predictions accounting for an elastic regime followed by elastic instability and compaction. Strong evidence of reinforcement in the MWCNT/epoxy composites was indicated by increased strength, stiffness and toughness values with respect to the as-grown mats and pure polymer. The elastic instability strain of the composites was of the order of 0.4.     

Synthesis and properties of new CdSe-AgI-As2Se3 chalcogenide glasses

The glass-forming region in the pseudo-ternary CdSe-AgI-As₂Se₃ system was determined. Measurements including differential scanning calorimetry (DSC), density, and X-ray diffraction were performed. The effect resulting from the addition of CdSe or AgI has been highlighted by examining three series of different base glasses. The characteristic temperatures of the glass samples, including glass transition (T_g), crystallisation (T_x), and melting (T_m) temperatures are reported and used to calculate their ΔT = T_x − T_g and their Hruby, H_r = (T_x − T_g)/(T_m − T_x), criteria. Evolution of the total electrical conductivity σ and the room temperature conductivity σ₂₉₈ was also studied. The terahertz transparency domain in the 50-600 cm⁻¹ region was pointed for different chalcogenide glasses (ChGs) and the potential of the THz spectroscopy was suggested to obtain structural information on ChGs.     

Magnetically-sensitive shape memory polyurethane composites crosslinked with multi-walled carbon nanotubes

Magnetically-sensitive polyurethane composites, which were crosslinked with multi-walled carbon nanotubes (MWCNTs) and were filled with Fe₃O₄ nanoparticles, were synthesized via in situ polymerization method. MWCNTs pretreated with nitric acid were used as crosslinking agents. Because of the crosslinking of MWCNTs with polyurethane prepolymer, the properties of the composites with a high content of Fe₃O₄ nanoparticles, especially the mechanical properties, were significantly improved. The composites showed excellent shape memory properties in both 45 °C hot water and an alternating magnetic field (f = 45 kHz, H = 29.7 kA m⁻¹). The shape recovery time was less than one minute and the shape recovery rate was over 95% in the alternating magnetic field.     

Effects of poly(oxyethylene)-block structure in polyetheramines on the modified carbon nanotube/poly(lactic acid) composites

The hybrids of multi-walled carbon nanotube and poly(lactic acid) (MWCNT/PLA) were prepared by a melt-blending method. In order to enhance the compatibility between the PLA and MWCNTs, the surface of the MWCNTs was covalently modified by Jeffamine® polyetheramines by functionalizing MWCNTs with carboxylic groups. Different molecular weights and hydrophilicity of the polyethermaines were grafted onto MWCNTs with the assistance of a dehydrating agent. The results showed that low-molecular-weight Jeffamine® polyetheramine modified MWCNTs can effectively improve the thermal properties of PLA composites. On the other hand, high-molecular-weight and poly(oxyethylene)-segmented polyetheramine could render the modified MWCNTs of well dispersion in PLA, and consequently affecting the improvements of mechanical properties and conductivity of composite materials. With the addition of 3.0 wt% MWCNTs, the increment of E′ of the composite at 40 °C was 79%. For conductivity, the surface resistivity decreased from 1.27 × 10¹² Ω/sq for neat PLA to 8.30 × 10⁻³ Ω/sq for the composites.     

Enhanced dielectric and ferroelectric properties induced by TiO2@MWCNTs nanoparticles in flexible poly(vinylidene fluoride) composites

Flexible polymer based composites containing multi-walled carbon nanotubes (MWCNTs) have been reported to present high dielectric constant. However, the composites generally exhibit high dielectric loss and low dielectric breakdown strength, which prohibits their practical use in electronic and electric industry. MWCNTs were coated with a continuous layer of TiO₂ nanoparticles (TiO₂@MWCNTs) by a simple hydrothermal process and TiO₂@MWCNTs/poly(vinylidene fluoride) (PVDF) composites were prepared by a solution casting method. Compared to the pristine MWCNTs/PVDF composites, the TiO₂@MWCNTs/PVDF composites presented enhanced dielectric constant and lower dielectric loss. Additionally, the breakdown strength of the TiO₂@MWCNTs/PVDF composites was also improved, which is favorable for enhanced ferroelectric properties in the composites.     

Manufacturing techniques and property evaluations of conductive composite yarns coated with polypropylene and multi-walled carbon nanotubes

This study uses a melt extrusion method, a method for producing wires, to coat polyester (PET) yarns with polypropylene (PP) and multi-walled carbon nanotubes (MWCNTs). The resulting PP/MWCNTs-coated PET conductive yarns are tested for their tensile properties, processability, morphology, melting and crystallization behaviors, electrical conductivity, and applications. The test results indicate that tensile strength of the conductive yarns increases with an increase in the coiling speed that contributes to a more single-direction-orientated MWCNTs arrangement as well as a greater adhesion between PP/MWCNTs and PET yarns. 8 wt% MWCNTs results in an 18 °C higher crystallization temperature (T_c) of PP and an electrical conductivity of 0.8862 S/cm. The test results of this study have proven that this form of processing technology can prepare PP/MWCNTs-coated PET conductive yarns that have satisfactory tensile properties and electrical conductivity, and can be used in functional woven fabrics and knitted fabrics.     

High thermal and mechanical properties enhancement obtained in highly filled polybenzoxazine nanocomposites with fumed silica

Highly filled polybenzoxazine nanocomposites filled with nano-SiO₂ particles were investigated for their mechanical and thermal properties as a function of filler loading. The nanocomposites were prepared by high shear mixing followed by compression molding. A very low A-stage viscosity of benzoxazine monomer gives it excellent processability having maximum nano-SiO₂ loading as high as 30 wt% (18.8 vol%) with negligible void content. Moreover, thermal analysis of the curing process of the compound of the PBA-a/nano-SiO₂ composites was found to be autocatalytic in nature with average activation energy of 79–92 kJ mol⁻¹. Microscopic analysis (SEM) performed on the PBA-a/nano-SiO₂ composite fracture surface indicated a nearly homogeneous distribution of the nano-scaled silica in the polybenzoxazine matrix. In addition, the enhancement in storage modulus of the nano-SiO₂ filled polybenzoxazine composites was found to be significantly higher than that of the recently reported nano-SiO₂ filled epoxy composites. The dependence of the nanocomposites’ modulus on the nano-SiO₂ particles content is well fitted by the generalized Kerner equation. Furthermore, the relatively high micro-hardness of the PBA-a/nano-SiO₂ composites up to about 600 MPa was achieved. Finally, the substantial enhancement in the glass transition temperature (T_g) of the PBA-a/nano-SiO₂ composites was also observed with the ΔT_g up to 16 °C at the nano-SiO₂ loading of 30 wt%. The resulting PBA-a/nano-SiO₂ composite is a highly attractive candidate as coating material in electronic packaging or other related applications.     

Tensile and thermomechanical properties of short carbon fiber reinforced polyamide 6 composites

In this study, carbon fiber (CF) reinforced polyamide 6 (PA6) composites were prepared by using melt mixing method. Effects of fiber length and content, on the mechanical, thermal and morphological properties of CF reinforced PA6 composites were investigated. Fiber length distributions of composites were also determined by using an image analyzing program. It was seen that the maximum number of fibers were observed in the range of 0–50 μm. Mechanical test results showed that, increasing CF content increased the tensile strength, modulus and hardness values but decreased strain at break values of composites. DSC results showed that T_g and T_m values of composites were not changed significantly with increasing CF content and length. However, heat of fusion and the relative degree of crystallinity values of composites decreased with ascending CF content. DMA results revealed that storage modulus and loss modulus values of composites increased with increasing CF content.