Direct measurements of interfacial shear strength of multi-walled carbon nanotube/PEEK composite using a nano-pullout method

This paper presents a proposal of a simple and easy method to evaluate the interfacial shear strength (IFSS) of CNT-dispersed polymer composites. An individual multi-wall carbon nanotube (MWNT) was pulled out from a MWNT-dispersed/PEEK composite using a nano-pullout testing system installed in an SEM. The tensile load was measured using the elastic deformation of an AFM cantilever. The pull-out length was controlled by making a through-thickness hole near the specimen edge using a focused ion beam (FIB) system. The IFSS of a MWNT/PEEK composite was measured as 3.5-14 MPa, which agrees with the IFSS estimated from the macroscopic stress-strain behavior of the MWNT/PEEK composites.     

Interfacial shear strength of a glass fiber/epoxy bonding in composites modified with carbon nanotubes

In recent years, carbon nanotubes (CNTs) grown on fibers have attracted a lot of interest as an additional reinforcing component in conventional fiber-reinforced composites to improve the properties of the fiber/matrix interface. Due to harsh growth conditions, the CNT-grafted fibers often exhibit degraded tensile properties. In the current study we explore an alternative approach to deliver CNTs to the fiber surface by dispersing CNTs in the fiber sizing formulation. This route takes advantage of the developed techniques for CNT dispersion in resins and introduces no damage to the fibers. We focus on unidirectional glass fiber/epoxy macro-composites where CNTs are introduced in three ways: (1) in the fiber sizing, (2) in the matrix and (3) in the fiber sizing and matrix simultaneously. Interfacial shear strength (IFSS) is investigated using single-fiber push-out microindentation. The results of the test reveal an increase of IFSS in all three cases. The maximum gain (over 90%) is achieved in the composite where CNTs are introduced solely in the fiber sizing.     

Temperature dependence of the interfacial shear strength in glass-fibre polypropylene composites

The present work focuses on further investigation of the hypothesis that a significant fraction of the level of apparent IFSS in glass fibre-reinforced thermoplastic composites can be attributed to a combination of thermal residual stress and static friction at the fibre-polymer interface. In order to obtain information on the temperature dependence of glass fibre-polypropylene IFSS a thermo-mechanical analyser has been adapted to enable interfacial microbond testing to be carried out in a well controlled temperature environment. Test results obtained by TMA-microbond testing showed excellent comparability with those obtained by normal microbond testing. The temperature dependence of IFSS of glass fibre-polypropylene was measured in the range from −40 °C up to 100 °C. The IFSS showed a highly significant inverse dependence on testing temperature with a major increase in the glass transition region of the PP matrix. It is shown that approximately 70% of the apparent room temperature IFSS in this system can be attributed to residual radial compressive stress at the fibre-matrix interface.     

Interfacial load transfer in carbon nanotube/ceramic microfiber hybrid polymer composites

Growing carbon nanotubes (CNTs) on the surface of fibers has the potential to modify fiber–matrix interfacial adhesion, enhance the composite delamination resistance, and possibly improve its toughness and any matrix-dominated elastic property as well. In the present work aligned CNTs were grown upon ceramic fibers (silica and alumina) by chemical vapor deposition (CVD) at temperatures of 650 °C and 750 °C. Continuously-monitored single fiber composite (SFC) fragmentation tests were performed on pristine as well as on CNT-grown fibers embedded in epoxy. The critical fragment length, fiber tensile strength at critical length, and interfacial shear strength were evaluated. Significant increases (up to 50%) are observed in the fiber tensile strength and in the interfacial adhesion (which was sometimes doubled) with all fiber types upon which CNTs are CVD-grown at 750 °C. We discuss the likely sources of these improvements as well as their implications.     

Multifunctional properties of high volume fraction aligned carbon nanotube polymer composites with controlled morphology

Advanced composites, such as those used in aerospace applications, employ a high volume fraction of aligned stiff fibers embedded in high-performance polymers. Unlike advanced composites, polymer nanocomposites (PNCs) employ low volume fraction filler-like concepts with randomly-oriented and poorly controlled morphologies due to difficult issues such as dispersion and alignment of the nanostructures. Here, novel fabrication techniques yield controlled-morphology aligned carbon nanotube (CNT) composites with measured non-isotropic properties and trends consistent with standard composites theories. Modulus and electrical conductivity are maximal along the CNT axis, and are the highest reported in the literature due to the continuous aligned-CNTs and use of an unmodified aerospace-grade structural epoxy. Rule-of-mixtures predictions are brought into agreement with the measured moduli when CNT waviness is incorporated. Waviness yields a large (10×) reduction in modulus, and therefore control of CNT collimation is seen as the primary limiting factor in CNT reinforcement of composites for stiffness. Anisotropic electron transport (conductivity and current-carrying capacity) follows expected trends, with enhanced conductivity and Joule heating observed at high current densities.     

Strengths of C/C composites under tensile, shear, and compressive loading: Role of interfacial shear strength

Various strengths of carbon–carbon composites (C/Cs) are comprehensively reviewed. The topics reviewed include tensile, shear, compressive, and fatigue strength as well as fiber/matrix interfacial strength of C/Cs. When data are available, high temperature properties, including creep behavior, are presented. Since C/Cs have extremely low fiber/matrix interfacial strength τ_d, the interfacial fracture plays important roles in all of the fracture processes dealt in this review. The low τ_d was found to divide tensile fracture units into small bundles, to seriously degrade both shear and compressive strength, and to improve fatigue performance. In spite of the importance of the interfacial strength of C/Cs, techniques for its evaluation and analysis are still in a primitive stage.     

Application of continuously-monitored single fiber fragmentation tests to carbon nanotube/carbon microfiber hybrid composites

To assess the effect of carbon nanotube (CNT) grafting on interfacial stress transfer in fiber composites, CNTs were grown upon individual carbon T-300 fibers by chemical vapor deposition. Continuously-monitored single fiber composite (SFC) fragmentation tests were performed on both pristine and CNT-decorated fibers embedded in epoxy. The critical fragment length, fiber tensile strength at critical length, and interfacial shear strength were evaluated. Despite the fiber strength degradation resulting from the harsh CNT growth conditions, the CNT-modified fibers lead to a twofold increase in interfacial shear strength which correlates with the nearly threefold increase in apparent fiber diameter resulting from CNT grafting. These observations corroborate recently published studies with other CNT-grafted fibers. An analysis of the relative contributions to the interfacial strength of the fiber diameter and strength due to surface treatment is presented. It is concluded that the common view whereby an experimentally observed shorter average fragment length leads to a stronger interfacial adhesion is not necessarily correct, if the treatment has changed the fiber tensile strength or its diameter.     

Influence of hard segment content and nature on polyurethane/multiwalled carbon nanotube composites

Knowledge of how polyurethanes, PU, complexity affects their derived multiwalled carbon nanotube, MWCNT, composites could shed important clues for preparing future tailored PU/MWCNT elastic, strong and electrically conductive composites. In this regard, hard segment content and nature, along with MWCNT functionalisation, are believed to have great influence on both nanoscale PU/MWCNT self assembling mechanisms and on final composites properties. In this work the effect of PU hard segment content into composites was analysed. According to the results, a preferential interaction of nanotubes with polyurethanes hard segments can be assumed although nanotubes introduction hindered both soft and hard segments crystallisation. In all cases carbon nanotubes percolative network formation seemed to be crucial for obtaining significant reinforcement, being observed at this stage, a reduction of ductility, phenomena which is related to an increase on hard domains interconnections by MWCNT. The hard to soft segment ratio into PU plays a crucial role on determining the stress transfer to MWCNT. In addition, PU hard domains nature has important effect on nanotubes reinforcing character, this fact being related to the different PU intrinsic morphologies as well as different PU-MWCNT interactions.     

The effect of interfacial state on the thermal conductivity of functionalized Al2O3 filled glass fibers reinforced polymer composites

Rapidly increasing packaging density of electronic devices puts forward higher requirements for thermal conductivity of glass fibers reinforced polymer (GFRP) composites, which are commonly used as substrates in printed circuit board. Interface between fillers and polymer matrix has long been playing an important role in affecting thermal conductivity. In this paper, the effect of interfacial state on the thermal conductivity of functionalized Al₂O₃ filled GFRP composites was evaluated. The results indicated that amino groups-Al₂O₃ was demonstrated to be effective filler to fabricate thermally conductive GFPR composite (1.07 W/m K), compared with epoxy group and graphene oxide functionalized Al₂O₃. It was determined that the strong adhesion at the interface and homogeneous dispersion of filler particles were the key factors. Moreover, the effect of interfacial state on dielectric and thermomechanical properties of GFRP composites was also discussed. This research provides an efficient way to develop high-performance GFRP composites with high thermal conductivity for integrated circuit packaging applications.     

Improved cryogenic interlaminar shear strength of glass fabric/epoxy composites by graphene oxide

The cryogenic interlaminar shear strength (ILSS) at cryogenic temperature (77 K) of glass fabric (GF)/epoxy composites is investigated as a function of the graphene oxide (GO) weight fraction from 0.05 to 0.50 wt% relative to epoxy. For the purpose of comparison, the ILSS of the GF/epoxy composites is also examined at room temperature (RT, 298 K). The results show that the cryogenic ILSS is greatly improved by about 32.1% and the RT ILSS is enhanced by about 32.7% by the GO addition at an appropriate content of 0.3 wt% relative to epoxy. In addition, the ILSS of the composite at 77 K is much higher than that at RT due to the relatively strong interfacial GF/epoxy adhesion at 77 K compared to the RT case.     

Fabrication of multi-walled carbon nanotube-reinforced carbon fiber/silicon carbide composites by polymer infiltration and pyrolysis process

Multi-walled carbon nanotube (MWNT)-reinforced carbon fiber/silicon carbide (C_f/SiC) composites were prepared using a polymer infiltration and pyrolysis (PIP) process. The MWNTs used in this study were modified using a chemical treatment. The MWNTs were found to be well dispersed in the matrix after ultrasonic dispersion, and the mechanical properties of the C_f/SiC composite were significantly improved by the addition of MWNTs. The addition of 1.5 wt.% of MWNTs to the C_f/SiC composite led to a 29.7% increase in the flexural strength, and a 27.9% increase in the fracture toughness.     

Development of aligned-hemp yarn-reinforced green composites with soy protein resin: Effect of pH on mechanical and interfacial properties

Unidirectional hemp yarn-reinforced green composites were fabricated with soy protein concentrate (SPC) resin processed at various pH values. To preserve the yarn alignment during the fabrication of green composites, hemp yarn was wound onto a metal frame with slight tension and precured SPC resin was applied to the yarns. Effects of pH values on the tensile properties of the SPC resin and hemp yarn/SPC resin interfacial shear strength (IFSS) were investigated. Increasing pH of the SPC resin from 7 to 12 decreased its fracture stress and Young’s modulus from 13.1 MPa and 357.5 MPa to 8.1 MPa and 156.2 MPa, respectively. At the same time fracture strain and moisture content increased from 31.5% and 15.65% to 53·4% and 19.30%, respectively, indicating resin plasticization. However, hemp yarn/SPC resin IFSS increased from 17.7 MPa at pH 7 up to 28.0 MPa at pH 10, after which it decreased. The fracture toughness of the composites increased up to pH of 10 but further increase in pH reduced the toughness. SEM photomicrographs showed fracture surfaces of hemp yarn-reinforced green composites that indicated better resin/fiber interaction at pH of 10 than 7 or 12.     

Review of the mechanical properties of carbon nanofiber/polymer composites

In this paper, the mechanical properties of vapor grown carbon nanofiber (VGCNF)/polymer composites are reviewed. The paper starts with the structural and intrinsic mechanical properties of VGCNFs. Then the major factors (filler dispersion and distribution, filler aspect ratio, adhesion and interface between filler and polymer matrix) affecting the mechanical properties of VGCNF/polymer composites are presented. After that, VGCNF/polymer composite mechanical properties are discussed in terms of nanofibers dispersion and alignment, adhesion between the nanofiber and polymer matrix, and other factors. The influence of processing methods and processing conditions on the properties of VGCNF/polymer composite is also considered. At the end, the possible future challenges for VGCNF and VGCNF/polymer composites are highlighted.     

The effect of pre-softened wood chips on wood fibre aspect ratio and mechanical properties of wood–polymer composites

The objective of this work was to study the effect of chemical pre-treatment and moisture content of wood chips on the wood particle aspect ratio after compounding in a twin-screw extruder and on the mechanical properties of wood–polymer composites (WPCs). Composites with 50 wt.% wood content were manufactured using pre-treated and untreated wood chips. The effect of wood moisture content on composite properties was studied by using dried and undried wood chips. The mechanical properties and fracture surfaces of the composites as well as the microstructure and aspect ratio of wood particles after compounding were studied. The highest wood particle aspect ratio after extrusion was achieved by using pre-treated, undried wood chips as raw material. The chemical pre-treatment was found to enhance the defibration of wood chips as well as the mechanical properties of the composites.     

Hybrid nanoreinforced carbon/epoxy composites for enhanced damage tolerance and fatigue life

Hybrid nano/microcomposites with a nanoparticle reinforced matrix were developed, manufactured, and tested showing significant enhancements in damage tolerance properties. A woven carbon fiber reinforced polymer composite, with the polymer (epoxy) matrix reinforced with well dispersed carbon nanotubes, was produced using dispersant-and-sonication based methods and a wet lay-up process. Various interlaminar damage tolerance properties of this composite, including static strength, fracture toughness, fatigue life, and crack growth rates were examined experimentally and compared with similarly-processed reference material produced without nanoreinforcement. Significant improvements were obtained in interlaminar shear strength (20%), fracture toughness (180%), shear fatigue life (order of magnitude), and fatigue crack growth rate (factor of 2). Observations by scanning electron microscopy of failed specimens showed significant differences in fracture surface morphology between the two materials, related to the differences in properties and providing context for understanding of the enhancement mechanisms.     

Nano-epoxy resins containing electrospun carbon nanofibers and the resulting hybrid multi-scale composites

For the first time, electrospun carbon nanofibers (ECNFs, with diameters and lengths of ∼200 nm and ∼15 μm, respectively) were explored for the preparation of nano-epoxy resins; and the prepared resins were further investigated for the fabrication of hybrid multi-scale composites with woven fabrics of conventional carbon fibers via the technique of vacuum assisted resin transfer molding (VARTM). For comparison, vapor growth carbon nanofibers (VGCNFs) and graphite carbon nanofibers (GCNFs) were also studied for making nano-epoxy resins and hybrid multi-scale composites. Unlike VGCNFs and GCNFs that are prepared by bottom-up methods, ECNFs are produced through a top-down approach; hence, ECNFs are more cost-effective than VGCNFs and GCNFs. The results indicated that the incorporation of a small mass fraction (e.g., 0.1% and 0.3%) of ECNFs into epoxy resin would result in substantial improvements on impact absorption energy, inter-laminar shear strength, and flexural properties for both nano-epoxy resins and hybrid multi-scale composites. In general, the reinforcement effect of ECNFs was similar to that of VGCNFs, while it was higher than that of GCNFs.     

Fabrication and mechanical properties of well-dispersed multiwalled carbon nanotubes/epoxy composites

Multiwalled carbon nanotubes (MWCNTs)/epoxy nanocomposites were fabricated by using ultrasonication and the cast molding method. In this process, MWCNTs modified by mixed acids were well dispersed and highly loaded in an epoxy matrix. The effects of MWCNTs addition and surface modification on the mechanical performances and fracture morphologies of composites were investigated. It was found that the tensile strength improved with the increase of MWCNTs addition, and when the content of MWCNTs loading reached 8 wt.%, the tensile strength reached the highest value of 69.7 MPa. In addition, the fracture strain also enhanced distinctly, implying that MWCNTs loading not only elevated the tensile strength of the epoxy matrix, but also increased the fracture toughness. Nevertheless, the elastic modulus reduced with the increase of MWCNTs loading. The reasons for the mechanical property changes are discussed.     

Effect of silica coating thickness on the thermal conductivity of polyurethane/SiO2 coated multiwalled carbon nanotube composites

Silica coated multiwalled carbon nanotubes (SiO₂@MWCNTs) with different coating thicknesses of ∼4 nm, 30–50 nm, and 70–90 nm were synthesized by a sol–gel method and compounded with polyurethane (PU). The effects of SiO₂@MWCNTs on the electrical properties and thermal conductivity of the resulting PU/SiO₂@MWCNT composites were investigated. The SiO₂ coating maintained the high electrical resistivity of pure PU. Meanwhile, incorporating 0.5, 0.75 and 1.0 wt% SiO₂@MWCNT (70–90 nm) into PU, produced thermal conductivity values of 0.287, 0.289 and 0.310 W/mK, respectively, representing increases of 62.1%, 63.3% and 75.1%. The thermal conductivity of PU/SiO₂@MWCNT composites was also increased by increasing the thickness of the SiO₂ coating.     

Influence of titanium carbide on the interlaminar shear strength of carbon fibre laminate composites

The potential use of carbon fibre laminate composites is limited by the weak out-of-plane properties, especially delamination resistance. The effect of incorporating titanium carbide to the mesophase pitch matrix precursor of carbon fibre laminate composites on interlaminar shear strength is studied both on carbonised and graphitised composites. The presence of titanium carbide modifies the optical texture of the matrix from domains to mosaics in those parts with higher concentrations and it contributes to an increase of fibre/matrix bonding. This fact produces an increase of the interlaminar shear strength of the material and changes the fracture mode.     

Macroscopic analysis of interfacial properties of flax/PLLA biocomposites

This study presents results from a study of the mechanical behaviour of flax reinforced Poly(l-Lactic Acid) (PLLA) under in-plane shear and mode I interlaminar fracture testing. Slow cooling of the unreinforced polymer has been shown to develop crystalline structure, causing improvement in matrix strength and modulus but a drop in toughness. The in-plane shear properties of the composite also drop for the slowest cooling rate, the best combination of in-plane shear performance and delamination resistance is noted for an intermediate cooling rate, (15.5 °C/min). The values of G_Ic obtained at this cooling rate are higher than those for equivalent glass/polyester composites. These macro-scale results have been correlated with microdroplet interface debonding and matrix characterization measurements from a previous study. The composite performance is dominated by the matrix rather than the interface.