Irrigated composite liner designs for fast hydration and prevention of thermal desiccation of geosynthetics clay liners

In composite liners made of geomembrane (GMB)-geosynthetics clay liners (GCLs), maintaining bentonite in the GCL in a suitably hydrated state is critical for their performance. Hydration of GCL from subsoil, following industry best practice, is time consuming and conditional on suitable water chemistry in subsoil. In addition, under thermal gradients, dehydration occurs, with moisture migrating downwards to the subsoil, leading to the development of cracks in the bentonite and hence loss of performance.Two novel ideas are proposed in this paper, namely hydration of GCLs by artificial irrigation and hydraulic separation of the liner system from the underlying subsoil. Three new composite liner designs allowing for actively irrigating a geosynthetic clay liner (GCL) through a geocomposite layer were investigated. In two of the three designs, the hydraulic connection between the GCL and the subsoil was broken by placing an additional GMB between them. The new designs were tested in column experiments under 20 kPa overburden pressure and temperatures of up to 78 °C applied to the top of the liner. The performances of the new designs were compared to that of a standard GCL-GMB design where GCL was allowed to hydrate from a well-graded sandy subsoil. Three scenarios for the staging of hydration and thermal load application were investigated.Under active hydration of the composite liners, it took less than 14 days for the GCLs to reach a gravimetric water content ω of 110–130%, compared to 49 days taken to reach ω~95% under hydration from the subsoil. GCLs in the new designs in which the hydraulic connection with the subsoil was broken, remained well-hydrated (ω>100%) after 14 days of heating and no cracks appeared in the bentonite. On the other hand, the GCL in the conventional design experienced severe desiccation under the same conditions. The new designs hence offer a viable solution to the problem of slow hydration and/or thermal desiccation of GCLs.     

Experimental study on the permeability and self-healing capacity of geosynthetic clay liners in heavy metal solutions

Geosynthetic clay liners (GCLs), which have a very low permeability to water and a considerably high self-healing capacity, are widely used in liner systems of landfills. In this study, a series of experimental tests were carried out under complex conditions on typical commercial GCLs from China. In particular, the effects of pH values and lead ions (Pb²⁺) were tested in addition to other factors. The swelling properties of natural bentonite encapsulated between geotextile components in the GCLs were tested first. The swelling capacity was reduced rapidly at pH values < 3 and concentrations of Pb²⁺ >40 mM. Permeability tests on GCLs with different concentrations of lead ions were then performed by using the self-developed multi-link flexible wall permeameter, and data showed that increases in lead ion concentrations greatly improved the permeability. Finally, self-healing capacity tests were conducted on needle-punched GCLs under different levels of damage. Results showed that the GCLs have a good self-healing capacity with small diameter damage holes (2 mm, close to three times the original aperture), but with a damage aperture larger than 15% of the sample area, the self-healing capacity could not prevent leakage; hence, in certain situations it will be necessary to repair the damage to meet the anti-seepage requirement.     

Hydraulic conductivity of geosynthetic clay liners to tailings impoundment solutions

The results of a comprehensive testing program conducted to evaluate the hydraulic conductivity (k) of two geosynthetic clay liners (GCLs) considered as a liner component for a tailings impoundment at a proposed zinc and copper mine are reported. The two GCLs were permeated with a relatively low ionic-strength ground water (GW) from the mine site and two electrolyte solutions, a process water (PW) and a simulated leachate (SL), with chemical compositions consistent with those expected during operation of the impoundment. A total of 22 flexible-wall tests were performed to determine the effects of prehydration with the GW, type of GCL, type of permeant liquid, and duration of the back-pressure stage of the test. The k values for both GCLs permeated with the GW were 1.7 × 10⁻⁹ cm/s, which is within the range 1–3 × 10⁻⁹ cm/s typically reported for GCLs permeated with low ionic-strength liquids, such as deionized water. However, the mean values of k based on permeation of duplicate specimens of both types of GCL with either PW or SL relative to the values of k based on permeation with GW, or k/k_w, ranged from a factor of 200 (2.3 orders of magnitude) to a factor of 7600 (3.9 orders of magnitude). Thus, both tailings impoundment solutions had significant adverse impacts on the hydraulic performance of both GCLs. Given the overall range of k/k_w values, factors such as prehydration, type of GCL, type of permeant liquid, and duration of back pressure, were relatively insignificant. The results of this study serve to emphasize the need to perform hydraulic conductivity testing using site specific materials.     

Effect of water salinity on the water retention curve of geosynthetic clay liners

The effect of water salinity on the water retention curve of geosynthetic clay liners (GCLs), under constant volume condition is examined. The results indicate that at a constant gravimetric moisture content the total suction increases as the salinity of the wetting liquid increases. Furthermore, the difference in total suction between the GCL hydrated by saline water and distilled water is greater than the difference in the osmotic potential of the wetting water. This behaviour is possibly caused by the matric suction being affected by the expected chemically induced pore size change of the bentonite component of the GCL.     

Hydraulic conductivity of two geosynthetic clay liners permeated with a hyperalkaline solution

GCLs containing powdered Na-bentonite treated with different dosages of a proprietary additive intended to reduce the impacts of chemical interactions were permeated with three solutions: a hyperalkaline solution (1 M NaOH and 1.3 mM CsCl) having similar pH to aluminum refining leachate, a 1.3 mM CsCl solution (no NaOH), and DI water. For a given permeant solution, the hydraulic conductivity of both GCLs was similar. Thus, the higher additive dosage had no measureable impact on hydraulic conductivity. Hydraulic conductivity of both GCLs decreased by a factor of approximately 1.5–1.8 during permeation with CsCl in response to osmotic swelling induced by the low ionic strength of the CsCl solution entering the pore space. In contrast, permeation with the NaOH–CsCl solution caused the hydraulic conductivity of both GCLs to increase modestly (<50 times the hydraulic conductivity to DI water), and then level out (or decrease slightly) as a result of reduced osmotic swelling in the interlayer combined with dissolution of the mineral. For the tests conducted with CsCl solution, nearly all of the Cs was adsorbed by the bentonite. In contrast, Cs broke through readily when the NaOH–CsCl solution was used as the permeant solution. Permeation with the NaOH–CsCl solution also increased the sodicity of the bentonite by replacing bound K, Ca, and Mg on the mineral surface.     

Hysteresis of the water retention curves of geosynthetic clay liners in the high suction range

This paper examines two needle-punched geosynthetic clay liners' water retention behaviour at high suction ranges using the vapour equilibrium technique where super-saturated salt solutions controlled the relative humidity. This study shows that the bentonite form and its mineralogy affect the absorption/desorption of GCLs and their corresponding water retention curves. In particular, a granular bentonite-based GCL was found to absorb more and release less water than a powdered bentonite-based GCL due to its higher montmorillonite content and larger pores. The water retention curves of both GCLs exhibited very little hysteretic behaviour at high suction. Repeated wetting-drying cycles shifted the WRCs of both GCLs slightly downward with minimal impact on their degree of hysteresis.     

Effect of specimen preparation on the swell index of bentonite-polymer GCLs

Experiments were conducted to investigate how specimen preparation (crushing and sieving) affects the swell index (SI) of bentonite-polymer (B–P) composites and the relationship between SI and hydraulic conductivity of B–P GCLs. Seven B–P and one Na–B GCLs were used in this study. Tests were conducted using DI water and synthetic municipal solid waste incineration ash leachates. Specimens were prepared using the ASTM D5890 and two alternative methods prior to SI testing. For both Na–B and B–P composites, <100% of the specimen passed through the #100 sieve regardless of the amount of crushing performed using a mortar and pestle. SIs and loss on ignitions (LOI) of the portion of the B–P composites passing #100 sieve were comparable to the Na–B, whereas the B–P specimen retained on #100 sieve had very high SIs and LOIs. These observations indicate that crushing and sieving of the B–P composites lead to segregation of polymer. A stronger correlation (R² = 0.90) was observed between SI and hydraulic conductivity, only when SI tests were conducted with B–P without any crushing and sieving, suggesting that SI tests should conduct with B–P composites retrieved from the GCLs without sieving to provide a better prediction of hydraulic compatibility.     

Effect of geotextile ageing and geomembrane surface roughness on the geomembrane-geotextile interfaces for heap leaching applications

A series of large scale direct shear experiments is used to investigate the effect of the geomembrane (GMB) surface roughness, geotextile (GTX) properties, and GTX ageing, on the GMB-GTX interface shear behaviour. Interfaces involving smooth, coextruded textured, and structured surface GMBs underlying four different nonwoven needle-punched staple fibres (GTXs) with mass per unit areas between 200 and 2400 g/m², and a geocomposite drain (GCD) are examined at normal stresses between 250 and 1000 kPa. The results showed that the interlocking between the GMB and GTX increased with increasing the GMB asperity height and/or decreasing the mass per unit area of the GTX. For the interfaces that involved GTXs preaged prior to the shear box experiments for up to 2 years at 85 °C, it was found that the 2400 g/m² heat bonded two-layered GTX exhibited internal shear failure at low shear displacements. However, all the highly aged single layered GTXs showed an increase in the peak interface friction angles with the increase in their ageing. For these single layered GTX, the results suggest that assessing the interface friction angles using unaged GTXs for the stability analysis is conservative as long as the GTX remains intact in the field.     

Investigating factors influencing polymer elution and the mechanism controlling the chemical compatibility of GCLs containing linear polymers

A study was conducted to investigate (1) physicochemical factors that influence polymer elution from GCLs containing a blend of bentonite and linear (water-soluble) polymer (LPB GCLs) and (2) the mechanism that controls the chemical compatibility of LPB GCLs when polymer elutes. A series of hydraulic conductivity (k), free swell and viscosity tests were performed on a commercial LPB GCL using DI water, varying concentrations of NaCl and CaCl?. Comparable tests were also performed on a conventional bentonite (CB) GCL containing the same untreated bentonite and the same physical properties as the LPB GCL. The LPB GCL showed improved swelling and hydraulic performance compared to the CB GCL when permeated with salt solutions. Total organic carbon analysis of the effluents showed that polymer eluted from the LPB GCL regardless of the permeant solution. However, the rate at which polymer eluted increased as the concentration and valence of the dominant cation increased. The rate at which polymer eluted also increased with hydraulic gradient. The mass of polymer retained inside the GCL matrix did not correlate with the k of the LPB GCL. Free swell tests coupled with chemical analysis suggest that, the improved chemical compatibility of the LPB GCL was due to the ability of the polymer to scavenge cations from the solution which allows the bentonite to undergo adequate swelling during the initial hydration period. Analogous to water-prehydrated CB GCLs, the dispersed structure of the bentonite fabric and increased adsorbed water molecules attained during initial swelling controls the k of the LPB GCL when polymer elutes.     

Stress-controlled direct shear testing of geosynthetic clay liners I: Apparatus development

The use of geosynthetic clay liners (GCLs) in waste containment applications can induce long-term normal and shear stresses as well as expose GCLs to elevated temperatures and non-standard hydration solutions. Considering the importance of GCL internal shear strength to the design and integrity of waste containment barrier systems, innovative laboratory testing methods are needed to assess shear behavior of GCLs. There were two main objectives of this study: (i) develop a stress-controlled direct shear apparatus capable of testing GCLs exposed to elevated temperatures and hydrated in non-standard solutions; and (ii) assess internal shear behavior of GCLs under varying experimental conditions (e.g., stress, temperature, solution). These two objectives were partitioned into a two-paper set, whereby Part I (this paper) focuses on the shear box design and Part II focuses on an assessment of shear behavior. The direct shear apparatus includes a reaction frame to mitigate specimen rotation that develops from an internal moment within needle-punched reinforced GCLs. Rapid-loading shear tests were conducted to assess functionality of the apparatus and document baseline shear behavior for a heat-treated and a non-heat treated needle-punched GCL with comparable peel strength. These two GCLs failed at comparable applied shear stress; however, the heat-treated GCL yielded lower shear deformation and failure occurred via rupture of reinforcement fiber anchors, whereas the non-heat treated GCL yielded larger shear deformation and failure via pullout of reinforcement fibers.     

Investigation of initial hydration and rehydration of geosynthetic clay liners from sandy subgrades via X-ray computed tomography images

The hydraulic conductivity of geosynthetic clay liners (GCLs) widely used as barrier systems considerably depends on their hydration status after the initial hydration of virgin GCLs and the rehydration of desiccated GCLs. Free hydration tests were performed on virgin and desiccated GCLs over sandy subgrades to compare their hydration level. In addition, high-resolution micro-X-ray computed tomography (CT) images of both GCLs and sandy subgrades with different gravimetric water content (i.e. 15%, 20%, and 25%) after the initial hydration were analyzed for better insights. The results show significant influences of subgrade water content on moisture content and thickness of virgin GCLs. Water loss of sandy subgrades and the time interval necessary for reaching a steady state of desiccated GCLs during rehydration was greater and longer than virgin GCLs during initial hydration. X-ray CT images verified a dense distribution of bentonite particles, macropores, and minor desiccation cracks that existed in poorly-hydrated GCLs over unsaturated sand. On the other hand, the completely saturated sandy subgrade facilitated the hydration of GCLs, leaving a lot of macropores in the sand. The relationship between water distribution and the frequency of macropore generation observed in the upper contact zone of sandy subgrades was also indicated via these X-ray CT images.     

Combined effects of ammonium permeation and dry-wet cycles on the hydraulic conductivity and internal properties of geosynthetic clay liners

The hydraulic conductivity of geosynthetic clay liners (GCLs) permeated with deionized water (S0) and NH₄⁺ solutions, with concentrations of 100 mg/L (S100) and 1000 mg/L (S1000), was examined under six dry-wet cycles. The internal properties of virgin, desiccated, and healed GCLs were analyzed and quantified using X-ray computed tomography images. The hydraulic conductivity of the GCLs permeated with S0 and S100 underwent a negligible change during the six dry-wet cycles, whereas that of S1000 increased by almost three orders of magnitude after two desiccations. Each desiccation, after permeating with S0 and S100, generated a completely different macro-crack pattern; however, generation of macro-cracks at the same locations from dry cycles 2 to 6 and an abundance of micro-cracks were typical for S1000. This implies the severe deterioration of bentonite due to multi-desiccations and chemical compatibility with S1000. Moreover, the swell index of bentonite exposed to S1000 was reduced by approximately half, after six dry-wet cycles. Despite the lower volume percentage of macro-cracks for S1000 compared to S0 and S100, the swelling capacity of this bentonite was insufficient to fully heal these cracks. Hence, the swelling properties of bentonite dominate crack volume with regard to determining the hydraulic conductivity of GCLs.     

Assessment of consolidation-induced VOC transport for a GML/GCL/CCL composite liner system

In municipal solid waste landfills, a triple-layer composite liner consisting of a geomembrane liner (GML), a geosynthetic clay liner (GCL) and a compacted clay liner (CCL) is commonly used at the landfill bottom to isolate the leachates from surrounding environment. This paper presents a numerical investigation of the effect of liner consolidation on the transport of a volatile organic compound (VOC), trichloroethylene (TCE), through the GML/GCL/CCL composite liner system. The numerical simulations were performed using the model CST3, which is a piecewise linear numerical model for coupled consolidation and solute transport in multi-layered soil media and has been extensively validated using analytical solutions, numerical solutions and experimental results. The performed numerical simulations considered coupled consolidation and contaminant transport with representative geometry, material properties, and applied stress conditions for a GML/GCL/CCL liner system. The simulation results indicate that, depending on conditions, consolidation of the GCL and CCL can have significant impact on the transport results of TCE (i.e., TCE mass flux, cumulative TCE mass outflow, and distribution of TCE concentration within the GCL and CCL), both during the consolidation process and long after the completion of consolidation. The traditional approach for the assessment of liner performance neglects consolidation of the GCL and CCL and fails to consider the consolidation-induced transient advection and concurrent changes in material properties and, therefore, can lead to significantly different results. These differences for with and without the consolidation effects can range over several orders of magnitude. The process of consolidation-induced contaminant transport is complex and involves many variables, and therefore case-specific analysis is necessary to assess the significance of liner consolidation on VOC transport through a GML/GCL/CCL composite liner system.     

Effect of gravel subgrade on hydraulic performance of geosynthetic clay liner

The effect of a gravel subgrade on the hydraulic performance of GCLs is investigated. Laboratory test results show that the GCL specimens exhibit significant variation in thickness when compressed against gravel. The maximum and minimum thicknesses of the specimen were about 20 and 3 mm, respectively, after consolidation by an effective stress up to 138 kPa. However, the permittivity of GCLs remained very low. The permittivity of both needle-punched and adhesive-bonded geotextile-supported GCLs decreased with increasing confining stress, regardless of the type of subgrade materials. In general, larger particles led to more significant migration of bentonite. Nevertheless, there was no significant difference in the degree of bentonite migration between the two GCLs investigated.     

Cyclic shear behavior of GMB/GCL composite liner

The composite liner system consisting of geomembrane (GMB) and geosynthetic clay liner (GCL) has been widely used in landfills. Although there have been a lot of studies on the monotonic shear behavior of GMB/GCL composite liner, the dynamic test data are still very limited and consequently, the dynamic shear mechanism is not clear. A series of displacement-controlled cyclic shear tests were conducted to study the shear behavior of GMB/GCL composite liner, including the shear stress versus horizontal displacement relationships, backbone curves, and shear strengths. Hysteretic loops in the shape of parallelogram were obtained and equivalent linear analyses revealed that the secant shear stiffness decreased and the damping ratio increased with the rise in loading cycles. According to the test results, it is generally acceptable to predict the dynamic peak strength of a GMB/GCL composite liner with its static strength envelope. Furthermore, the dynamic softening mechanism and rate-dependent shear stiffnesses were well described by the proposed equations, which also facilitate the accurate modeling of the cyclic shear behavior.     

Hydration/dehydration behaviour of geosynthetic clay liners in the Antarctic environment

This paper examines the hydration/dehydration behaviour of geosynthetic clay liner (GCL) under polar conditions for four simulated conditions experienced at Australia's Casey Station in Antarctica: (a) hydration during summer, (b) dehydration during a winter-summer cycle, (c) hydration through a fine Antarctic soil, and (d) hydration through a coarse Antarctic soil. Hydration during the summer is found to occur if there is direct contact with the water table. In contrast, the low relative humidity of the environment tends to dehydrate the GCL along a path that depends on the field conditions the GCL is exposed to. Hydration from either fine or coarse Antarctica soil is function of the original gravimetric water content of the subgrade soil and its grain size distribution as well as the low relative humidity prevailing in Antarctica.     

土工合成材料与土界面作用特性的研究

土工合成材料加筋土工程中 ,土工合成材料与填料的界面作用特性是最关键的技术指标 ,因此利用直剪试验和拉拔试验研究土工合成材料与填料的界面作用特性是非常必要的。本文以 5种不同种类的国产土工合成材料为加筋材料 ,以砂和石灰粉煤灰为填料 ,通过直剪试验和拉拔试验比较各种国产土工合成材料与填料的界面作用特性 ,得到一些有益的结论 ,可指导土工合成材料的优选和研究加筋机理。     

Hydrodynamic assessment of bentonite granule size and granule swelling on hydraulic conductivity of geosynthetic clay liners

Flow in an idealized geosynthetic clay liner (GCL) containing bentonite comprised of equisized and equispaced square granules was simulated using a hydrodynamic model to quantitatively evaluate the premise that the hydraulic conductivity of GCLs diminishes as the bentonite granules hydrate and swell into adjacent intergranular pores, creating smaller and tortuous intergranular flow paths. Predictions with the model indicate that hydraulic conductivity decreases as granules swell and intergranular pores become smaller, and that greater granule swelling during hydration is required to achieve low hydraulic conductivity when the bentonite is comprised of larger granules, or the bentonite density is lower (lower bentonite mass per unit area). Predictions made with the model indicate that intergranular pores become extremely small (<1 μm) as the hydraulic conductivity approaches 10⁻¹¹ m/s. These outcomes are consistent with experimental data showing that GCLs are more permeable when hydrated and permeated with solutions that suppress swelling of the bentonite granules, and that the hydraulic conductivity of GCLs with bentonite having smaller intergranular pores (e.g., GCLs with smaller bentonite granules, more broadly graded particles, or higher bentonite density) is less sensitive to solutions that suppress swelling.     

Effect of geosynthetic component characteristics on the potential for GCL internal erosion

Experiments quantifying GCL permittivity and the ultimate water head the GCLs can sustain before the initiation of internal erosion when underlain by a 50 mm angular to subangular gravel subgrade are conducted. The influence of different geotextiles over the subgrade, water heads, hydration periods before testing, masses per unit area of bentonite within the GCL, and ionic strengths of the solution (cation exchange) are considered. Test results show that GCL with the scrim-reinforced nonwoven geotextile over the subgrade has the best hydraulic performance against internal erosion, followed by the woven geotextile coated with a 110 g/m² polypropylene film. A woven or nonwoven is the least useful for preventing internal erosion, with the corresponding threshold water head initiating internal erosion >39 m for scrim-reinforced nonwoven, 21 m for lightly coated woven, 4–5 m for woven and nonwoven alone, respectively. Cation exchange, length of hydration, and mass per unit area of bentonite do not notably affect the threshold water head for the subgrade examined. Once internal erosion occurs, there is a 3-order of magnitude increase in permittivity. The practical implications are discussed.     

Model test of clogging effects on composite foundation of geosynthetic-encased steel slag column

Experiments were conducted to study the performance of geosynthetic encased steel slag column with a diameter of 150 mm and a length of 900 mm in a soft clay foundation. The effect of clogging was simulated by mixing the slag with 10% and 20% fines. The measured bearing capacity of the column treated foundation is notably increased to about 10 times than that of the untreated foundation, and is seldom affected by the intrusion of fines. The vertical stress within the soil at column tip attenuates to 85% and 60% of the stress close to the ground surface for the column with no fines and 20% fines, respectively. For the cases with fines content of 10% and 20%, the maximum excess pore pressure is in average 5% and 10% greater than the case without fines, respectively, and the dissipation rate of excess pore pressure is in average 18% and 24% slower than the case without fines. The column treated foundation prevents the water ponding on the surface as that occurs for the untreated foundation. The undrained shear strength of the soil close to the column increases by 18% at the depth of 100 mm, and 6% at the depth of half column, regardless of the fines.