Effect of dimethyl sulfoxide on synthesis of thermoplastic cellulose‐Graft‐poly(l‐lactide) copolymer using ionic liquid as reaction media

In this study, ring‐opening graft polymerization of l ‐lactide onto cellulose was carried out homogeneously in ionic liquid (IL)/dimethyl sulfoxide (DMSO) co‐solvent as a reaction media. Through the effective control of high viscosity and steric hindrance caused by the interaction between the IL and the hydroxyl group of cellulose by adding DMSO as a co‐solvent, cellulose‐graft‐poly(l ‐lactide) (Cell‐g‐PLLA) copolymer with higher substitution efficiency was successfully prepared, at relatively low concentration of l ‐lactide. The maximum values of molar substitution, degree of lactyl substitution, and degree of polymerization of poly(l ‐lactide) in the copolymer were 3.76, 1.74, and 2.16, respectively, determined by ¹H‐NMR. The prepared cell‐g‐PLLA copolymers showed thermal plasticization with a glass transition temperature of 155°C. In addition, the thermal processibility could be improved as the amount of grafted PLLA in the copolymer increased. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41331.     

Preparation and characterization of poly(L‐lactide) membranes prepared by γ‐radiation‐induced grafting of N‐vinyl pyrrolidone

A copolymer, poly(L ‐lactide)‐g‐poly(N‐vinyl pyrrolidone) (PLLA‐g‐PVP) was prepared with poly(L ‐lactide) (PLLA) and N‐vinyl pyrrolidone in the presence of methanol as a solvent by γ‐ray irradiation. The structure of PLLA‐g‐PVP was characterized by ¹H‐NMR and Fourier transform infrared spectroscopy. The PLLA‐g‐PVP graft ratio calculated by the percentage increase in weight increased with the increase of absorbed dose, and the percentage crystallinity of PLLA‐g‐PVP decreased with increasing graft ratio. The introduction of the poly(N‐vinyl pyrrolidone) chain into PLLA resulted in a decrease in the contact angle of PLLA‐g‐PVP with increasing graft ratio. In vitro degradation testing showed that PLLA‐g‐PVP had a higher degradation rate both in the weight‐loss test and molecular weight measurement because of a lower crystalline percentage and higher hydrophilicity compared to PLLA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and dispersibility of poly(L‐lactide)‐grafted silica nanoparticle

To improve dispersibility of silica nanoparticle in organic solvents, the grafting of poly(L ‐lactide) (PLLA) onto silica nanoparticle surface by ring‐opening polymerization of L‐lactide (LA) was investigated in the presence of an amidine base catalyst. The ring‐opening polymerization of LA successfully initiated in the presence of silica having amino groups (silica‐NH₂) and an amidine base catalyst to give PLLA‐grafted silica, but not in the presence of untreated silica (silica‐OH). In the absence of the amidine base catalyst no ring‐opening polymerization of LA even in the presence of silica‐NH₂ and no grafting of PLLA onto silica were observed. It became apparent that the amidine base catalyst acts as an effective catalyst for the ring‐opening graft polymerization of LA from the surface of silica‐NH₂. In addition, it was found that the percentage of PLLA grafting onto silica could be controlled according to the reaction conditions. The average particle size of PLLA‐grafted silica was smaller than that of silica‐NH₂. Therefore, it was considered that the aggregation structure of silica nanoparticles was considerably destroyed by grafting of PLLA onto the surface. The PLLA‐grafted silica gave a stable dispersion in polar solvents, which are good solvents for PLLA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synthesis and characterization of AB‐type copolymers poly(L‐lactide)‐block‐poly(methyl methacrylate) via a convenient route combining ROP and ATRP from a dual initiator

Diblock copolymers of poly(L ‐lactide)‐block‐poly(methyl methacrylate) (PLLA‐b‐PMMA) were synthesized through a sequential two‐step strategy, which combines ring‐opening polymerization (ROP) and atom transfer radical polymerization (ATRP), using a bifunctional initiator, 2,2,2‐trichloroethanol. The trichloro‐terminated poly(L ‐lactide) (PLLA‐Cl) with high molecular weight (M_n,GPC = 1–12 × 10⁴ g/mol) was presynthesized through bulk ROP of L ‐lactide (L ‐LA), initiated by the hydroxyl group of the double‐headed initiator, with tin(II) octoate (Sn(Oct)₂) as catalyst. The second segment of the block copolymer was synthesized by the ATRP of methyl methacrylate (MMA), with PLLA‐Cl as macroinitiator and CuCl/N,N,N′,N″,N″‐pentamethyldiethylenetriamine (PMDETA) as catalyst, and dimethyl sulfoxide (DMSO) was chosen as reaction medium due to the poor solubility of the macroinitiator in conventional solvents at the reaction temperature. The trichloroethoxyl terminal group of the macroinitiator was confirmed by Fourier transform infrared spectroscopy (FTIR) and ¹H‐NMR spectroscopy. The comprehensive results from GPC, FTIR, ¹H‐NMR analysis indicate that diblock copolymers PLLA‐b‐PMMA (M_n,GPC = 5–13 × 10⁴ g/mol) with desired molecular composition were obtained by changing the molar ratio of monomer/initiator. DSC, XRD, and TG analyses establish that the crystallization of copolymers is inhibited with the introduction of PMMA segment, which will be beneficial to ameliorating the brittleness, and furthermore, to improving the thermal performance. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of poly(vinyl alcohol)‐graft‐poly(ε‐caprolactone) and poly(vinyl alcohol)‐graft‐poly(lactide) in melt with magnesium hydride as catalyst

Grafting of poly(ε‐caprolactone) (PCL) and poly(lactide) (PLA) chains on poly(vinyl alcohol) backbone (PVA degree of hydrolysis 99%) was investigated using MgH₂ environmental catalyst and melt‐grown ring‐opening polymerization (ROP) of ε‐caprolactone (CL) and L ‐lactide (LA), that avoiding undesirable toxic catalyst and solvent. The ability of MgH₂ as catalyst as well as yield of reaction were discussed according to various PVA/CL/MgH₂ and PVA/LA/MgH₂ ratio. PVA‐g‐PCL and PVA‐g‐PLA were characterized by ¹H‐ and ¹³C‐NMR, DSC, SEC, IR. For graft copolymers easily soluble in tetrahydrofuran (THF) or chloroform, wettability and surface energy of cast film varied in relation with the length and number of hydrophobic chains. Aqueous solution of micelle‐like particles was realized by dissolution in THF then addition of water. Critical micelle concentration (CMC) decreased with hydrophobic chains. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Plasticization of Poly‐L‐lactide with L‐lactide,D‐lactide,and D,L‐lactide monomers

Poly‐L ‐lactide (PLLA) is being widely considered for repair of damaged tissues, for controlled antibiotic release, and also as scaffolds for cultured cells. PLLA was blended with the lactide monomer in its two enantiomeric forms: D ‐lactide (D ‐la) and L ‐lactide (L ‐la) and with the cyclic dimmer D ,L ‐la, in order to enhance its flexibility and thereby overcome its inherent problem of brittleness. In this work, the crystallization, phase structure, and tensile properties of PLLA and PLLA plasticized with 5, 10, 15, and 20 wt% of D ‐la, L ‐la, and D ,L ‐la are explored. The three plasticizers used were effective in lowering the glass transition temperature (T_g) and the melting temperature (T_m) of PLLA, around 20°C for a plasticizer content of 20 wt%. The tensile strength and modulus of the blends decreased following the increasing content of plasticizers from approximately 58 MPa to values below 20 MPa, and from 1667 to 200 MPa, respectively. Aging the blends at storage ambient temperature revealed that the enhanced flexibility as well as the morphological stability was lost over time due to the migration of the plasticizer to the surface, this being less marked in the case of D ‐la as a result of interactions between the polymer and its enantiomeric monomer of complementary configuration. POLYM. ENG. SCI., 53:2073–2080, 2013. © 2013 Society of Plastics Engineers     

Surface modification of halloysite nanotubes with l‐lactic acid: An effective route to high‐performance poly(l‐lactide) composites

To improve the interfacial bonding between halloysite nanotubes (HNTs) and poly(l ‐lactide) (PLLA), a simple surface modification of HNTs with l ‐lactic acid via direct condensation polymerization has been developed. Two modified HNTs were obtained: HNTs grafting with l ‐lactic acid (l‐HNTs) and HNTs grafting with poly(l ‐lactide) (p‐HNTs). The structures and properties of l‐HNTs and p‐HNTs were investigated. Then, a series of HNTs/PLLA, l‐HNTs/PLLA and p‐HNTs/PLLA composites were prepared using a solution casting method and were characterized by polarized optical microscopy (POM), field scanning electron microscopy, and tensile testing. Results showed that l ‐lactic acid and PLLA could be easily grafted onto the surface of HNTs by forming an Al carboxylate bond and following with condensation polymerization, and the amounts of the l ‐lactic acid and PLLA grafted on the surface of the HNTs were 5.08 and 14.47%, respectively. The surface‐grafted l ‐lactic acid and PLLA played the important role in improving the interfacial bonding between the nanotubes and matrix. The l‐HNTs and p‐HNTs can disperse more uniformly in and show better compatibility with the PLLA matrix than untreated HNTs. As a result, the l‐HNTs/PLLA and p‐HNTs/PLLA composites had better tensile properties than that of the HNTs/PLLA composites. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41451.     

Novel bioresorbable hydrogels prepared from chitosan‐graft‐polylactide copolymers

A series of biodegradable chitosan‐graft‐polylactide (CS‐g‐PLA) copolymers were prepared by grafting of poly(L ‐lactide) (PLLA) or poly(D ‐lactide) (PDLA) precursor to the backbone of chitosan using N,N′‐carbonyldiimidazole as coupling agent. The composition of the copolymers was varied by adjusting the chain length of PLA as well as the ratio of chitosan to PLA. The copolymers synthesized via this ‘graft‐onto’ method present interesting properties as shown by NMR and infrared spectroscopy, gel permeation chromatography and solubility tests. Hydrogels were prepared by mixing water‐soluble CS‐g‐PLLA and CS‐g‐PDLA solutions. Gelation was assigned to stereocomplexation between PLLA and PDLA blocks as evidenced by differential scanning calorimetry and wide‐angle X‐ray diffraction measurements. Thymopentin (TP5) was taken as a model drug to evaluate the potential of these CS‐g‐PLA hydrogels as drug carriers. An initial burst and a final release up to 82% of TP5 were observed from high‐performance liquid chromatography analysis. Copyright © 2011 Society of Chemical Industry     

Degradation behaviors of linear low‐density polyethylene and poly(L‐lactic acid) blends

In this study, the degradability of linear low‐density polyethylene (LLDPE) and poly(L ‐lactic acid) (PLLA) blend films under controlled composting conditions was investigated according to modified ASTM D 5338 (2003). Differential scanning calorimetry, X‐ray diffraction, and Fourier transform infrared spectroscopy were used to determine the thermal and morphological properties of the plastic films. LLDPE 80 (80 wt % LLDPE and 20 wt % PLLA) degraded faster than grafted low‐density polyethylene–maleic anhydride (M‐g‐L) 80/4 (80 wt % LLDPE, 20 wt % PLLA, and 4 phr compatibilizer) and pure LLDPE (LLDPE 100). The mechanical properties and weight changes were determined after composting. The tensile strength of LLDPE 100, LLDPE 80, and M‐g‐L 80/4 decreased by 20, 54, and 35%, respectively. The films, as a result of degradation, exhibited a decrease in their mass. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Cold‐crystallization behavior of poly(L‐lactide)/ACR blend films investigated by in situ FTIR spectroscopy

The cold crystallization behavior of poly (L ‐lactide) (PLLA) blend films modified by small amount of acrylic rubber particles (ACR) have been investigated by in situ Fourier‐transform infrared (FTIR) spectroscopy. During the isothermal cold crystallization, the crystallization rate of PLLA is greatly improved with addition of only 1 wt % ACR. However, for PLLA with 8 wt % ACR, the crystallization rate is slower than that of neat PLLA. The relative crystallinity of PLLA with the addition of 1–5 wt % ACR is obviously higher than that of the neat PLLA. For the PLLA blend film with 3 % ACR, the relative crystallinity reaches a maximum. It was found that the addition of ACR particles below 5% accelerated the cold crystallization nucleation process and made the cold‐crystallization rate of PLLA/ACR be quicker than that of neat PLLA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Preparation of diblock copolymers consisting of methoxy poly(ethylene glycol) and poly(ε‐caprolactone)/poly(L‐lactide) and their degradation property

Methoxy poly(ethylene glycol)‐b‐poly(ε‐caprolactone) (MPEG‐PCL) or MPEG‐b‐poly(L ‐lactide) (MPEG‐PLLA) diblock copolymers were prepared by the polymerization of CL or LA, using MPEG as an initiator in the presence of stannous octoate. MPEG‐b‐poly(ε‐caprolactone‐ran‐L ‐lactide) (MPEG‐PCLA) diblock copolymers with different chemical composition of PCL and PLLA were also prepared by adjusting the amount of CL and LA from MPEG in the presence of stannous octoate. In degradation study, the degradation of the MPEG‐PCLA diblock copolymers mainly depends on the PCL and PLLA segments present in their structure. MPEG‐PCLA, with intermediate ratio of PCL and PLLA segment, completely degraded after 14 weeks. Meanwhile, partially degraded MPEG‐PCLA segments and parent MPEG segments were observed at higher PCL or PLLA segment contents. Introduction of PLLA into the PCL segments caused a lowering of the crystallinity of the diblock copolymers, thus, inducing a faster incoming of water into the copolymers. We confirmed that the diblock copolymers, with lower degree of crystallinity, have degraded more rapidly. POLYM. ENG. SCI., 46: 1242–1249, 2006. © 2006 Society of Plastics Engineers     

Solid‐state linear viscoelastic properties of intercalated poly(L‐lactide)/organo‐modified montmorillonite hybrids

Hybrids of poly(L ‐lactide)/organophilic clay (PLACHs) have been prepared by a melt‐compounding process using poly(L ‐lactide) (PLLA) and different contents of surface‐treated montmorillonite modified with a dimethyl dioctadecyl ammonium salt. The dispersion structures of clay particles in PLACHs were investigated using wide‐angle X‐ray diffraction and transmission electron microscopy. The solid‐state linear viscoelastic properties for these PLACHs were examined as functions of temperature and frequency. The incorporation of organo‐modified silicate into PLLA matrix enhanced significantly both storage moduli (E′) and loss moduli (E″). The strong enhancement observed in dynamic moduli of PLACHs could be attributed to uniformly dispersed state of the clay particles with high aspect ratio (= length/thickness of clay) and the intercalation of the PLLA chains between silicate layers. Copyright © 2006 Society of Chemical Industry     

Fabrication and in vitro investigation of nanohydroxyapatite,chitosan, poly(L‐lactic acid) ternary biocomposite

The nanohydroxyapatite/chitosan/poly(L ‐lactic acid) (HA/CS/PLLA) ternary biocomposites were prepared by blending the hydroxyapatite/chitosan (HA/CS) nanocomposites with poly(L ‐lactic acid) (PLLA) solution. Surface modification by grafting D ‐, L ‐lactic acid onto the HA/CS nanocomposites was designed to improve the bonding with PLLA. The FTIR and ¹³C‐NMR spectrum confirmed that the oligo(lactic acid) was successfully grafted onto the HA/CS nanocomposites, and the time‐dependent phase monitoring showed that the grafted copolymers were stable. The TEM morphology of the HA/CS/PLLA ternary nanocomposites showed that nano‐HA fibers were distributed homogeneously, compacted closely and wrapped tightly by the CS and PLLA matrix. The ternary biocomposites with the HA content of 60 and 67 wt % exhibited high compressive strength of about 160 MPa and suitable hydrophilicity. The in vitro tests exhibited that the ternary biocomposites have good biodegradability and bioactivity when immersed in SBF solutions. All the results suggested that the n‐HA/CS/PLLA ternary biocomposites are appropriate to application as bone substitute in bone tissue engineering. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Reactive blending of poly(L‐lactic acid) with poly(ethylene‐co‐vinyl alcohol)

Poly(L ‐lactic acid) (PLLA) was blended with poly(ethylene‐co‐vinyl alcohol) (EVOH) in the presence of an esterification catalyst to induce reaction between the hydroxyl groups of EVOH and the terminal carboxylic group of PLLA. Nascent low‐molecular‐weight PLLA, obtained from a direct condensation polymerization of L ‐lactic acid in bulk state, was used for the blending. Domain size of the PLLA phase in the graft copolymer was much smaller than that corresponding to a PLLA/EVOH simple blend. The mechanical properties of the graft copolymer were far superior to those of the simple blend, and the graft copolymer exhibited excellent mechanical properties even though the biodegradable fraction substantially exceeded the percolation level. The grafted PLLA reduced the crystallization rate of the EVOH moiety. Melting peak temperature (T_m) of the PLLA phase was not observed until the content of PLLA in the graft reaction medium went over 60 wt %. The modified Sturm test results demonstrated that biodegradation of EVOH‐g‐PLLA took place more slowly than that of an EVOH/PLLA simple blend, indicating that the chemically bound PLLA moiety was less susceptible to microbial attack than PLLA in the simple blend. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 886–890, 2005     

Stretch‐induced molecular ordering in amorphous/crystalline polylactide blends

The effect of amorphous poly(D ,L ‐lactide) (PDLLA) on the molecular orientation and crystallization of crystalline poly(L ‐lactide) (PLLA) on stretching is reported in this study. It is indicated that the presence of PDLLA in its miscible blends with PLLA is not favorable for either cohesive mesophase formation below T_g or strain‐induced crystallization above T_g at strains beyond the segmental extensibility limit. Because of lack of constraints imposed by cohesive mesophase or crystals, oriented segments are liable to slide each other or recoil, responsible for low‐molecular orientation in the stretched blends. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Syntheses of poly(lactic acid)‐poly(ethylene glycol) serial biodegradable polymer materials via direct melt polycondensation and their characterization

Directly starting from lactic acid (LA) and poly(ethylene glycol) (PEG), biodegradable material polylactic acid‐polyethylene glycol (PLEG) was synthesized via melt copolycondensation. The optimal synthetic conditions, including prepolymerization method, catalyst kinds and quantity, copolymerization temperature and time, LA stereochemical configuration, feed weight ratio m_LA/m_PEG and M_n of PEG, were all discussed in detail. When D ,L ‐LA and PEG (M_n = 1000 Da) prepolymerized together as feed weight ratio m_{D ,l‐LA}/m_PEG = 90/10, 15 h copolycondensation under 165°C and 70 Pa, and 0.5 wt % SnO as catalyst, gave D ,L ‐PLEG1000 with the highest [η] of 0.40 dL/g, and the corresponding MW was 41,700 Da. Using L ‐LA instead of D ,L ‐LA, 10 h polymerization under 165°C and 70 Pa, and 0.5 wt % SnO as catalyst, gave L ‐PLEG1000 with the highest [η] of 0.21 dL/g and MW of 15,600 Da. Serial D ,L ‐PLEG with different feed weight ratio and M_n of PEG were synthesized via the simple and practical direct melt copolycondensation, and characterized with FTIR, ¹H NMR, GPC, DSC, XRD, and contact angle testing. D ,L ‐PELG not only had higher MW than PDLLA, PLLA and L ‐PELG, but also better hydrophilicity than PDLLA. The novel one‐step method could be an alternative route to the synthesis of hydrophilic drug delivery carrier PLEG instead of the traditional two‐step method using lactide as intermediate. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 577–587, 2006     

Synthesis,physical properties,and crystallization of optically active poly(L‐phenyllactic acid) and poly(L‐phenyllactic acid‐co‐L‐lactic acid)

Optically active poly(L ‐phenyllactic acid) (Ph‐PLLA), poly(L ‐lactic acid) (PLLA), and poly(L ‐phenyllactic acid‐co‐L ‐lactic acid) with weight‐average molecular weight exceeding 6 × 10³ g mol^?1 were successfully synthesized by acid catalyzed direct polycondensation of L ‐phenyllactic acid and/or L ‐lactic acid in the presence of 2.5–10 wt % of p‐toluenesulfonic acid. Their physical properties and crystallization behavior were investigated by differential scanning calorimetry, thermogravimetry, and polarimetry. The absolute value of specific optical rotation ([α]) for Ph‐PLLA (?38 deg dm^?1 g^?1 cm³) was much lower than that of [α] for PLLA (?150 deg dm^?1 g^?1 cm³), suggesting that the helical nature was reduced by incorporation of bulky phenyl group. PLLA was crystallizable during solvent evaporation, heating from room temperature, and cooling from the melt. Incorporation of a very low content of bulky phenyllactyl units even at 4 mol % suppressed the crystallization of L ‐lactyl unit sequences during heating and cooling, though the copolymers were crystallizable for L ‐phenylactyl units up to 6 mol % during solvent evaporation. The activation energy of thermal degradation (ΔE_td) for Ph‐PLLA (200 kJ mol^?1) was higher than that for PLLA (158 kJ mol^?1). The ΔE_td for the copolymers increased with an increase in L ‐phenyllactyl unit content. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(l‐lactide)/four‐armed star poly(l‐lactide)‐grafted multiwalled carbon nanotubes nanocomposites: Preparation,rheology, crystallization,and mechanical properties

Four‐armed star poly(l ‐ lactide)‐grafted multiwalled carbon nanotubes (CNTs‐g‐4PLLA) were synthesized through the nucleophilic substitution reaction between 4PLLA and acryl chloride of CNTs and then characterized by transmission electron microscope, X‐ray photoelectron spectroscopy, thermal gravimetric analysis (TGA), and ultraviolet visible spectrophotometer. The results indicated that 4PLLA was successfully grafted onto CNTs, and CNTs‐g‐4PLLA contained 37.7 wt% of 4PLLA. PLLA/CNTs‐g‐4PLLA nanocomposites were prepared by solution casting with different CNTs‐g‐4PLLA content. Rheological behavior of PLLA/CNTs‐g‐4PLLA nanocomposites was measured using a rheometer. The result showed that CNTs‐g‐4PLLA formed a network structure at percolation concentration, which improves obviously rheological properties of PLLA in the molten state. The crystallization behavior and crystal structure of the nanocomposites were comprehensive evaluated through differential scanning calorimetry, X‐ray diffraction, and polarizing optical microscope. The results found that CNTs‐g‐4PLLA played two roles in PLLA crystallization. The addition of CNTs‐g‐4PLLA acted as nucleating agent and obviously accelerated the spherulites growth under percolation concentration, while it inhibited the movement of PLLA chains at above percolation concentration, resulting in the decrease of crystallinity. Thermal stability and mechanical properties of the nanocomposites were also investigated using TGA, dynamic mechanical analysis, and tensile test. These results indicated that the incorporation of CNT‐g‐4PLLA into the PLLA matrix improved the thermal stability, storage modulus, and tensile strength of the nanocomposites. POLYM. COMPOS., 37:2744–2755, 2016. © 2015 Society of Plastics Engineers     

Enhanced toughness and strength of poly (d‐lactide) by stereocomplexation with 5‐arm poly (l‐lactide)

The enhancement of mechanical properties were achieved by solution blending of poly(d ‐lactide) (PDLA) and 5‐arm poly(l ‐lactide) (5‐arm PLLA). Differential scanning calorimetry (DSC) and wide‐angle X‐ray diffraction (WAXD) results indicated almost complete stereocomplex could be obtained when 5‐arm PLLA exceeded 30wt %. Tensile test results showed that the addition of 5‐arm PLLA in linear PDLA gave dramatically improvement both on tensile strength and elongation at break, which generally could not be increased simultaneously. Furthermore, this work transformed PDLA from brittle polymer into tough and flexible materials. The mechanism was proposed based on the TEM results: the stereocomplex crystallites formed during solvent evaporation on the blends were small enough (100–200 nm), which played the role of physical crosslinking points and increased the interaction strength between PDLA and 5‐arm PLLA molecules, giving the blends high tensile strength and elongation at break. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42857.     

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) graft copolymers and their application as carriers for drug delivery system

Poly(N‐isopropylacrylamide‐co‐hydroxyethyl methacrylate) [P(NIPAM‐co‐HEMA)] copolymer was synthesized by controlled radical polymerization from respective N‐isopropylacrylamide (NIPAM) and hydroxyethyl methacrylate (HEMA) monomers with a predetermined ratio. To prepare the thermosensitive and biodegradable nanoparticles, new thermosensitive graft copolymer, poly(L ‐lactide)‐graft‐poly(N‐isoporylacrylamide‐co‐hydroxyethyl methacrylate) [PLLA‐g‐P(NIPAM‐co‐HEMA)], with the lower critical solution temperature (LCST) near the normal body temperature, was synthesized by ring opening polymerization of L ‐lactide in the presence of P(NIPAM‐co‐HEMA). The amphiphilic property of the graft copolymers was formed by the grafting of the PLLA hydrophobic chains onto the PNIPAM based hydrophilic backbone. Therefore, the graft copolymers can self‐assemble into uniformly spherical micelles ò about 150–240 nm in diameter as observed by the field emission scanning electron microscope and dynamic light scattering. Dexamethasone can be loaded into these nanostructures during dialysis with a relative high loading capacity and its in vitro release depends on temperature. Above the LCST, most of the drugs were released from the drug‐loaded micelles, whereas a large amount of drugs still remains in the micelles after 48 h below the LCST. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012