Behavior of sulfonated poly(ether ether ketone) in ethanol–water systems

The behavior of sulfonated poly(ether ether ketone) (sPEEK) membranes in ethanol–water systems was studied for possible application in direct ethanol fuel cells (DEFCs). Polymer membranes with different degrees of sulfonation were tested by means of uptake, swelling, and ethanol transport with dynamic measurements (liquid–liquid and liquid–gas systems). Ethanol permeability was determined in an liquid–liquid diffusion cell. For membranes with an ion‐exchange capacity (IEC) between 1.15 and 1.75 mmol/g, the ethanol permeability varied between 5 × 10^?8 and 1 × 10^?6 cm²/s, being dependent on the measuring temperature. Ethanol and water transport in liquid–gas systems was tested with pervaporation as a function of IEC and temperature. Higher IEC accounted for higher fluxes and lower water/ethanol selectivity. The temperature had a large effect on the fluxes, but the selectivity remained constant. Furthermore, the membranes were characterized with proton conductivity measurements. The proton diffusion coefficient was calculated, and a transition in the proton transfer mechanism was found at a water number of 12. Membranes with high IEC (>1.6 mmol/g) exhibited larger proton diffusion coefficients in ethanol–water systems than in water systems. The membrane with the lowest IEC exhibited the best proton transport to ethanol permeability selectivity. The use of sPEEK membranes in DEFC systems depends on possible modifications to stabilize the membranes in the higher conductive region rather than on modifications to increase the proton conductivity in the stable region. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effects of heat treatment on the properties of heterogeneous cation permeable membranes from blends of poly(ether sulfone)/sulfonated poly(phenylene sulfide) and phenolphthalein poly(ether ether ketone)/sulfonated poly(phenylene sulfide)

The effects of heat treatment on the properties of membranes prepared from blends of poly(ether sulfone)/sulfonated poly(phenylene sulfide) (SPPS) and phenolphthalein poly(ether ether ketone)/SPPS were studied in detail. The membranes' fundamental properties, including water content, transport number, diffusion coefficient of electrolytes, flux, and so on, changed with both treated temperature and time, whereas the ion‐exchange capacity and electrical resistance remained approximately unchanged. The trends may have been due to the possible structural change resulted from the shrinking of the polymers forming the membranes. Furthermore, the membranes also retained a good physical appearance at temperatures below 220°C. Therefore, a series of heterogeneous membranes with desired conductivities and selectivities as well as proper water contents, which could satisfy different industrial purposes, such as electrodialysis, diffusional dialysis, and proton exchange, were achieved by simple heat treatment for a proper time and at a proper temperature. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 494–499, 2005     

Effect of PES on the morphology and properties of proton conducting blends with sulfonated poly(ether ether ketone)

Development of alternate materials to Nafion, based on ionically conducting polymers and their blends is important for the wider applications of proton exchange membrane fuel cells. In this work, blends of sulfonated poly(ether ether ketone) (SPEEK) with poly(ether sulfone) (PES) are investigated. SPEEK with various ion exchange capacity (IEC) was prepared and blended with PES, which is nonionic and hydrophobic in nature. A comparative study of the water uptake, proton conductivity, and thermo‐mechanical characteristics of SPEEK and the blend membranes as a function of the IEC is presented. Addition of PES decreases the water uptake and conductivity of SPEEK. Chemical and thermal stability and mechanical properties of the membrane improve with the addition of PES. The effect of water content on the thermo‐mechanical properties of membranes was also studied. The morphology of blend membranes was studied using SEM to understand the microstructure and miscibility of the components. On the basis of the results, a plausible microstructure of the blends is presented, and is shown to be useful in understanding the variation of different properties with blending. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization and melting behavior of poly(ether ether ketone)/poly(aryl ether sulfone) blends

The crystallization and melting behavior of poly(ether ether ketone) (PEEK) in blends with poly(aryl ether sulfone) (PES) prepared by melt mixing are investigated by differential scanning calorimetry (DSC) and wide‐angle X‐ray scattering (WAXS). The presence of PES is found to have a notable influence on the crystallization behavior of PEEK, especially when present in low concentrations in the PEEK/PES blends. The PEEK crystallization kinetics is retarded in the presence of PES from the melt and in the rubbery state. An analysis of the melt crystallization exotherm shows a slower rate of nucleation and a wider crystallite size distribution of PEEK in the presence of PES, except at low concentrations of PES, where, because of higher miscibility and the tendency of PES to form ordered structures under suitable conditions, a significantly opposite result is observed. The cold crystallization temperature of the blends at low PES concentration is higher then that of pure PEEK, whereas at a higher PES concentration little change is observed. In addition, the decrease in heat of cold crystallization and melting, which is more prevalent in PEEK‐rich compositions than in pure PEEK, shows the reduction in the degree of crystallinity because of the dilution effect of PES. Isothermal cold crystallization studies show that the cold crystallization from the amorphous glass occurs in two stages, corresponding to the mobilization of the PEEK‐rich and PES‐rich phases. The slower rate of crystallization of the PEEK‐rich phase, even in compositions where a pure PEEK phase is observed, indicates that the presence of the immobile PES‐rich phase has a constraining influence on the crystallization of the PEEK‐rich phase, possibly because of the distribution of individual PEEK chains across the two phases. The various crystallization parameters obtained from WAXS analysis show that the basic crystal structure of PEEK remains unaffected in the blend. Further, the slight melting point depression of PEEK at low concentrations of PES, apart from several other morphological reasons, may be due to some specific interactions between the component homopolymers. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2906–2918, 2003     

Sulfonated poly(arylene ether ketone)s prepared by direct copolymerization as proton exchange membranes: Synthesis and comparative investigation on transport properties

Sulfonated poly(aryl ether ketone)s (SPAEK) copolymers were synthesized by aromatic nucleophilic polycondensation from 3,3′, 5,5′‐tetramethyl‐4, 4′–biphenol, 1,4‐bis(4‐fluorobenzoyl) benzene, and disulfonated difluorobenzophenone. The SPAEK membranes did not exhibit excessive swelling in hot water and at the same time show the proton conductivities in the range of 0.030 S/cm to 0.099 S/cm at 80°C. The methanol diffusion coefficients of the SPAEK membranes were in the range of 4.7 × 10^?7 to 8.1 × 10^?7cm²/s measured at 25°C. The transport properties of this series of SPAEK copolymers were compared to poly(aryl ether ether ketone)s (SPEEK), poly(aryl ether ether ketone ketone)s (SPEEKK), and Nafion® membranes. It was found that the transport properties (including proton conductivity and methanol permeability) follows the trend of SPEEKK‐60 < SPAEK‐60 < SPEEK‐60 < Nafion® 117, the order of which is also attributed to the differences in the chemical structure of the polymers and the membrane morphology. In general, this novel series of SPAEK membranes possess various advantages, such as low cost of the initial monomers, high thermal and mechanical stability, and low methanol permeability while simultaneously possessing sufficient proton conductivity, which makes them notably promising as proton exchange membrane (PEM) materials in direct methanol fuel cell (DMFC) applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Poly(ether ether ketone)/poly(aryl ether sulfone) blends: Relationships between morphology and mechanical properties

Mechanical properties such as the tensile modulus, yield (break) strength, and elongation to break (or yield) are measured for multiphase poly(ether ether ketone) (PEEK)/poly(aryl ether sulfone) (PES) blends. Specimens with three different levels of thermal histories (quenched, as‐molded, and annealed) are prepared in order to study their effects on the mechanical properties of PEEK/PES blends. Synergistic behavior is observed in the tensile modulus and tensile strength of the blends in almost the whole range of compositions. The ductility of quenched blends measured as the elongation to break (yield) shows an unexpected synergistic behavior in the blend containing 90 wt % PEEK, although a negative deviation from additive behavior is observed in the rest of the compositions. A ductile–brittle transition is observed between 50 and 75 wt % PEEK in the blend. The ductile–brittle transition in as‐molded blends shifts to 75–90 wt % PEEK. Annealed blends show predominantly brittle behavior in the whole composition range. The experimental data are further correlated with the theoretically predicted results based on various composite models. Although the prediction based on these equations fails to fit the experimental data in the whole composition range, the simplex equations that are normally used for blends showing synergistic behavior produced a reasonable fit to the experimental data. The mechanical properties obtained for different blend compositions are further correlated with their morphology as observed by scanning electron microscopy. Morphological observation shows a two‐phase morphology in PES‐rich blends, which is an interlocked morphology in which the disperse phase is not clearly visible in PEEK‐rich blends, and a cocontinuous type of morphology for a 50/50 composition. Considerable permanent deformation of both the disperse and matrix phase, especially in the case of quenched tensile specimens, demonstrates the remarkable adhesion present between the two phases. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 2887–2905, 2003     

Rheological properties in blends of poly(aryl ether ether ketone) and liquid crystalline poly(aryl ether ketone)

Rheological properties of the blends of poly(aryl ether ether ketone) (PEEK) with liquid crystalline poly(aryl ether ketone) containing substituted 3‐trifluoromethylbenzene side group (F‐PAEK), prepared by solution precipitation, have been investigated by rheometer. Dynamic rheological behaviors of the blends under the oscillatory shear mode are strongly dependent on blend composition. For PEEK‐rich blends, the systems show flow curves similar to those of the pure PEEK, i.e., dynamic storage modulus G′ is larger than dynamic loss modulus G″, showing the feature of elastic fluid. For F‐PAEK‐rich systems, the rheological behavior of the blends has a resemblance to pure F‐PAEK, i.e., G″ is greater than G′, showing the characteristic of viscous fluid. When the PEEK content is in the range of 50–70%, the blends exhibit an unusual rheological behavior, which is the result of phase inversion between the two components. Moreover, as a whole, the complex viscosity values of the blends are between those of two pure polymers and decrease with increasing F‐PAEK content. However, at 50% weight fraction of PEEK, the viscosity‐composition curves exhibit a local maximum, which may be mainly attributed to the phase separation of two components at such a composition. The changes of G′ and G″ with composition show a trend similar to that of complex viscosity. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 4040–4044, 2006     

Compatibility studies of sulfonated poly(ether ether ketone)–poly(ether imide)–polycarbonate ternary blends

Binary blends of the sulfonated poly(ether ether ketone) (SPEEK)–poly(ether imide) (PEI) and SPEEK–polycarbonate (PC), and ternary blends of the SPEEK–PEI–PC, were investigated by differential scanning calorimetry. SPEEK was obtained by sulfonation of poly(ether ether ketone) using 95% sulfuric acid. From the thermal analysis of the SPEEK–PEI blends, single glass transition temperature (T_g) was observed at all the blend composition. For the SPEEK–PC blends, double T_gs were observed. From the results of thermal analysis, it is suggested that the SPEEK–PEI blends are miscible and the SPEEK–PC blends are immiscible. Polymer–polymer interaction parameter (χ₁₂) of the SPEEK–PEI blends was calculated from the modified Lu and Weiss equation, and found to range from −0.011 to −0.825 with the blend composition. For the SPEEK–PC blends, the χ₁₂ values were calculated from the modified Flory–Huggins equation, and found to range from 0.191 to 0.272 with the blend composition. For the SPEEK–PEI–PC ternary blends, phase separation regions that showed two T_gs were found to be consistent with the spinodal curves calculated from the χ₁₂ values of the three binary blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 2488–2494, 2000     

Poly(aryl ether ketone)s with bromomethyl groups: Synthesis and quaternary amination

A series of bromomethylated poly(arylene ether ketone)s (PAEKs) with different contents of bromine tethered to the benzyl groups were successfully synthesized and characterized in this work. For this purpose, poly(arylene ether ketone) with 3,3′,5,5′‐tetramethyl‐4,4′‐dihydroxybipheny moiety (PAEK‐TM) was prepared by the aromatic nucleophilic polycondensation, and then the PAEK‐TM has benzylic methyl groups that were converted to bromomethyl groups by a radical reaction using N‐bromosuccinimide. Then, the bromomethylbenzyl groups in the membrane was converted to quaternary ammonium moieties in TMPAEK‐NOH. ¹H‐NMR measurements were used to characterize and confirm the structures of the resulting PAEK‐x‐BrTM and TMPAEK‐NBr derivatives (x refers to the molar percentage of bromine introduced per repeating units). TGA analysis showed that PAEK‐x‐BrTM exhibited a very low‐decomposition temperature at about 200°C corresponding to the C Br bond cleavage. The hydroxide conductivity of TMPAEK‐NOH membrane was 8 mS cm⁻¹ at room temperature, while the water uptake of TMPAEK‐NOH membrane was 22.3% at 20°C and 32.6% at 60°C. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Permeation resistance of poly(ether ether ketone) to hydrogen,nitrogen, and oxygen gases

We studied the gas permeation properties of poly(ether ether ketone) (PEEK) and compared it with two other polymers commonly used in the construction of semiconductor microenvironments, polycarbonate (PC), and poly(ether imide) (PEI). The PEEK specimens consisted of extruded films as well as compression‐ and injection‐molded specimens. The compression‐molded specimens were prepared to achieve the highest crystallinity. Injection‐molded disks, representing products, were milled to a prescribed thickness. Permeation, diffusion, and solubility coefficients were measured on these various PEEK specimens for hydrogen, nitrogen, and oxygen gases. It was found that PEEK generally has better permeation resistance than PC or PEI; showing up to five times lower permeation rates than PC or PEI, depending on grade, crystallinity, and gas. The superior permeation resistance of injection‐molded or extruded PEEK, when compared with similarly processed PC or PEI, comes from its crystallinity. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Tensile mechanical properties of sulfonated poly(ether ether ketone) (SPEEK) and BPO4/SPEEK membranes

A study to evaluate the tensile mechanical properties of sulfonated poly(ether ether ketone) (SPEEK) and BPO₄/SPEEK composite membranes has been carried out. It is aimed to give an assessment of these materials for applications in proton exchange membrane fuel cells. The stress–strain response of the membranes was measured as a function of the degree of sulfonation (DS) and the filler–matrix ratio. In addition, the effects of immersion in water at various temperatures were explored in situ by means of a homemade testing chamber fitted to the tensile analyzer. The results indicate that the DS has an important influence on the final mechanical behavior of the membranes. The introduction of the BPO₄ solid filler leads to deterioration in mechanical performance compared to unfilled SPEEK. A general picture of the microstructural features influencing the mechanical properties of SPEEK and BPO₄/SPEEK membranes is proposed. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2380–2393, 2005     

Hydrophilic TiO2 decorated carbon nanotubes/sulfonated poly(ether ether ketone) composite proton exchange membranes for fuel cells

Sulfonated poly(ether ether ketone) (SPEEK) is currently considered to be one of the most potential candidates of commercial perfluorinated sulfonic acid proton exchange membranes. To balance the proton conductivity and mechanical properties of SPEEK, nano TiO₂ coated carbon nanotubes (TiO₂@CNTs) were prepared using a benzyl alcohol-assisted sol-gel method and then used as a new nanofiller to modify SPEEK to prepare SPEEK/TiO₂@CNTs composite membranes. The thick insulated TiO₂ coating layer can effectively avoid the risk of electronic short-circuiting formed by CNTs, while the hydrophilicity of TiO₂ can also reduce the polar difference between CNTs and SPEEK matrix, thus promoting the homogeneous dispersion of CNTs in the composites. As a result, the composite membranes demonstrated simultaneously improved strength and proton conductivity. Incorporating 5 wt% of TiO₂@CNTs exhibited 31% growth in mechanical strength when compared with pure SPEEK. Moreover, the maximum conductivity was 0.104 S cm⁻¹ (80°C) for the composite membrane with 5 wt% of TiO₂@CNTs, which was nearly twice as high as that of SPEEK membrane (0.052 S cm⁻¹).     

Thermal properties of melt‐blended poly(ether ether ketone) and poly(ether imide)

The thermal properties of blends of poly(ether ether ketone) (PEEK) and poly(ether imide) (PEI) prepared by screw extrusion were investigated by differential scanning calorimetry. From the thermal analysis of amorphous PEEK–PEI blends which were obtained by quenching in liquid nitrogen, a single glass transition temperature (T_g) and negative excess heat capacities of mixing were observed with the blend composition. These results indicate that there is a favorable interaction between the PEEK and PEI in the blends and that there is miscibility between the two components. From the Lu and Weiss equation and a modified equation from this work, the polymer–polymer interaction parameter (χ₁₂) of the amorphous PEEK–PEI blends was calculated and found to range from −0.058 to −0.196 for the extruded blends with the compositions. The χ₁₂ values calculated from this work appear to be lower than the χ₁₂ values calculated from the Lu and Weiss equation. The χ₁₂ values calculated from the T_g method both ways decreased with increase of the PEI weight fraction. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 733–739, 1999     

Influence of silica content in sulfonated poly(arylene ether ether ketone ketone) (SPAEEKK) hybrid membranes on properties for fuel cell application

Sulfonated poly(arylene ether ether ketone ketone) (SPAEEKK) copolymer containing pendant sulfonic acid group (sulfonic acid content (SC) = 0.67) was synthesized from commercially available monomers such as sodium 6,7-dihydroxy-2-naphthalenesulfonate (DHNS), 1,3-bis(4-fluorobenzoyl)-benzene (BFBB), and hexafluorobisphenol A (6F-BPA). SPAEEKK/silica hybrid membranes were prepared using the sol-gel process under acidic conditions. The SPAEEKK/silica hybrid membranes were fabricated with different silica contents and the membranes were modified to achieve improved proton conductivity incorporating P-OH groups (H₃PO₄ treatment).The silica particles within the membranes were used for the purpose of blocking excessive methanol cross-over and for forming a pathway for proton transport due to water absorption onto the hydrophilic SiOH surface. The proton conductivities of H₃PO₄-doped membranes were somewhat higher than the un-doped (H₃PO₄-free) membranes due to increasing hydrophilicity of the membranes. The presence of silica particles within the organic polymer matrix, which decreases the ratio of free water to bound water due to the SiOH on the surface of silica derived from sol-gel reaction, results in hybrid membranes with reduced methanol permeability and improved proton conductivity.     

Synthesis and characterization of poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(arylene ether ketone) (S‐PAEK) block copolymers

A series of well‐defined poly(ether ketone ketone) (PEKK)/sodium sulfonated poly(aryl ether ketone) (S‐PAEK) block copolymers of high molecular weights was prepared by direct nucleophilic polymerization of hydroquinone with sodium 5,5′‐carbonylbis(2‐fluorobenzene sulfonate) ( 1 ) and PEKK oligomer ( 2 ). Varying the ratio of 1 to 2 used in polymerization can be used to control the degree of polymer sulfonation, which correspondingly affects the polymer solubility in solvents. Increasing content of 1 in the copolymers, slightly decreases their thermal stability which is nevertheless thermally stable up to 400 °C. Two T_g values, or one broad T_g, were observed in the DSC measurements of the block copolymers, indicating the existence of phase separation, which was further proved by phase‐separated morphologies as shown in atomic force microscopy images. © 2001 Society of Chemical Industry     

磺化聚醚醚酮的性能与应用

聚醚醚酮(PEEK)是一种性能优异的工程塑料。笔者简单地介绍了聚醚醚酮的特性,对近年来磺化聚醚醚酮的制备、SPEEK的性能及应用做了比较全面的归纳,并对磺化聚醚醚酮未来的发展前景进行了展望。     

Adhesion property of sulfonated poly(arylene ether sulfone)s

Sulfonated poly(arylene ether sulfone)s (S‐PESs) were synthesized from sulfonated 4,4′‐dichlorodiphenylsulfone (S‐DCDPS), 4,4′‐dichlorodiphenylsulfone (DCDPS), and 4,4′‐biphenol through variations in the molar ratio of S‐DCDPS to DCDPS from 10/90 to 40/60. The S‐PES sodium form was characterized with Fourier transform infrared, ¹H‐NMR, thermogravimetric analysis, differential scanning calorimetry, and dynamic mechanical analysis, and the intrinsic viscosity and solubility were also evaluated. The sodium form was then subjected to acidification by immersion in 1.5M HCl for 24 h at room temperature, which was followed by washing with deionized water. The S‐PES adhesive properties were measured with single laboratory shear samples with aluminum alloys, and the failure mode was investigated. The synthesized S‐PESs exhibited increased glass‐transition temperatures with increased S‐DCDPS/DCDPS ratios; their acid forms provided much lower glass‐transition temperatures than their sodium forms. In addition, the S‐PES sodium form exhibited a high intrinsic viscosity, which indicated a high molecular weight. The S‐PES acid form exhibited an adhesion strength similar to that of the sodium form, and the single‐lap‐shear strength increased with 10% S‐PES and then decreased with 20, 30, and 40% S‐PES. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 1211–1218, 2004     

Synthesis and properties of novel phosphorus‐containing poly(ether ether ketone ketone)s

A novel monomer, bis[4‐(4‐fluorobenzoyl)phenyl]phenylphosphine oxide, was synthesized through the reaction of bis(4‐chloroformylphenyl) phenyl phosphine oxide with fluorobenzene. Three poly(ether ether ketone ketone)s derived from bis[4‐(4‐fluorobenzoyl)phenyl]phenylphosphine oxide and different aromatic bisphenols were prepared by aromatic nucleophilic substitution reactions. The resulting polymers had inherent viscosities in the range of 0.55–0.73 dL/g. The structures of the poly(ether ether ketone ketone)s were characterized with Fourier transform infrared and ¹H‐NMR. Thermal analysis indicated that the glass‐transition temperatures of the poly(ether ether ketone ketone)s were higher than 200°C, and the 5% weight loss temperatures in nitrogen were higher than 463°C. All the polymers showed excellent solubility in polar solvents such as N‐methyl‐2‐pyrrolidone, dimethylformamide, and dimethylacetamide and could also be dissolved in chlorinated methane. The polymers afforded transparent and flexible films by solvent casting. Organic phosphorous moieties also imparted good flame‐retardancy to the polymers. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and properties of thio‐containing poly(ether ether ketone)s

A series of thio‐containing poly(ether ether ketone) (PEESK) polymers was synthesized by the introduction of thio groups from 4,4′ thiodiphenol (TDP) into the poly(ether ether ketone) (PEEK) structure via reaction between the phenol and aromatic fluoride groups. The effect of the thio groups on the properties of the PEESK materials was investigated. Differential scanning calorimetry (DSC) analysis and X‐ray diffraction (XRD) patterns show a depression in the crystallinity of the PEESKs with incorporation of the content of thio groups in the backbones. The crystalline structure was identified as an orthorhombic structure with lattice constants of a = 7.52 Å, b = 5.86 Å and c = 10.24 Å for all crystallizable PEESKs. The crystalline structures of the thio‐containing PEEK polymers were the same as that of the neat PEEK, which means the thio‐containing block in the whole thio‐containing PEEK molecule is almost excluded from the crystalline structure and the crystals are completely formed by ‘non‐thio’ blocks only. Due to the glass transition temperature (T_g) and melting temperature (T_m) depression with increase in the TDP content in the reaction system, the processability of the resultant thio‐containing PEEKs could be effectively improved. Copyright © 2004 Society of Chemical Industry     

Synthesis and characterization of novel (sulfonated) poly(arylene ether)s with pendent trifluoromethyl groups

This paper reports the synthesis of four different trifluoromethyl-substituted poly(arylene ether)s on the basis of 2,2-bis(4-hydroxyphenyl)hexafluoropropane (bisphenol AF) and various difluoro- or dinitrobiphenyl or terphenyl monomers in the course of a step-growth polycondensation. Besides a comparison between the polymerisability of the different monomer combinations, a main focus of this work lies on the NMR characterization of these poly(arylene ether)s. Poly(arylene ether)s with sufficiently high number average molecular weights were sulfonated by fuming sulfuric acid or chlorosulfonic acid and investigated in terms of membrane properties relevant for fuel cell applications.